Electrolux EFG 732 User manual

Page is loading ...

8

Wenn die Dunsthaube nicht funktioniert

Check that the power plug is connected to the wall

power outlet and that no fuse is blown. Do not do

any operations that can cause hazard or damage to

the product. If the problem remains contact your

dealer or an approved service company

Remember to save the purchase recite and the

Warranty card (only used in some countries)

Kundendienst

Bei eventuellen Rückfragen und Störungen rufen

Sie bitte unseren Kundendienst an (siehe

Kundendienst-Stellenverzeichnis).

Geben Sie beim Anruf an:

1. Die Modellbezeichnung

2. Die Produktnummer

3. Das Kaufdatum

Diese Daten finden Sie auf dem Typenschild

nach Öffnen der Fettfiltergitter auf der

Innenseite des Gerätes.

Konstruktions- und Farbänderungen im Rahmen

der technischen Entwicklung bleiben vorbehalten.

Ausbau der Dunsthaube aus dem

Möbelumbau

Montageschritte:

1. Metallfilter-Gitter und Gehäuseabdeckung

abnehmen.

2. Die 4 zusätzlichen Schrauben der

Rahmenbefestigung entfernen.

3. Schrauben an den beiden Befestigungsfedern

lockern (Fig. 13).

4. Einen Flachschraubendreher in das Loch der

Befestigungsfeder (rechts und links) einstecken

und die Befestigungsfeder jeweils nach innen

drücken (Fig. 14).

5. Gleichzeitig Dunstabzugshaube (rechts und

links) aus dem Möbelumbau ziehen.

Der Einbau erfolgt wie unter Montage beschrieben.

Fig. 14

Fig. 15

Page is loading ...

34

Technische gegevens

Model EFG 732 X EFG 532 X

Capaciteit hoog 450 m

3

/h

x)

286 m

3

/h 450 m

3

/h

x)

286 m

3

/h

laag 197 m

3

/h 197 m

3

/h

Afmetingen hoogte 302 mm 302 mm

breedte 748 mm 548 mm

diepte 302 mm 302

Verlichting 2 x PL 9 W 1 x PL 11 W

Vetfilters 1 pc 1 pc

Netspanning 230 V 230 V

Electric safety class Class 1 Class 1

Aansluitwaarde 204 W 197 W

x)

Bij gebruik als circulatiekap.

EFG 732 X afmetingen

710

4,5

748

70

160

283

302

510

4,5

548

70

160

283

302

EFG 532 X afmetingen

Page is loading ...

43

Contents

Safety instructions .............................................................................................................. 44

Description of the appliance .............................................................................................. 45

Function .................................................................................................................................................................45

Exhausting .............................................................................................................................................................45

Recycling ...............................................................................................................................................................45

Special accessories ............................................................................................................ 45

Installation ........................................................................................................................... 46

Unpacking..............................................................................................................................................................46

Placement ..............................................................................................................................................................46

Electrical connection .............................................................................................................................................46

Mounting of hood ..................................................................................................................................................46

Exhausting mode ...................................................................................................................................................47

Recirculation mode (with carbon filter) ................................................................................................................47

Using the hood .................................................................................................................... 47

Speed regulation ....................................................................................................................................................47

Work light ..............................................................................................................................................................47

Correct ventilation .................................................................................................................................................47

Important to know ...............................................................................................................47

Maintenance......................................................................................................................... 48

Grease filter ...........................................................................................................................................................48

Carbon filter...........................................................................................................................................................48

Cleaning.................................................................................................................................................................48

Changing the lighting elements .............................................................................................................................48

Demounting of the hood ........................................................................................................................................49

If the hood does not function............................................................................................. 49

Service and spare parts ..........................................................................................................................................49

Technical data...................................................................................................................... 50

EFG 732 X dimensions .........................................................................................................................................50

EFG 532 X dimensions .........................................................................................................................................50

44

Congratulations to your new Cooker Hood

Thank you for your choice of an Electrolux product. We are convinced that you will have

great use and pleasure from your new cooker hood.

Before you use the cooker hood we recommend that you read through the whole user

manual giving a direct description of the cooker hood and its functions.

To avoid the risks, that are always present when you use a product driven by electricity, it

is important that the cooker hood is installed correctly and that you read the safety instruc-

tions carefully to avoid misuse and hazard.

Save the instruction manual and keep it available at use of the cooker hood

Safety instructions

At installation and service

l The cooker hood is made for normal households

with normal cooking. If it is used for other

purposes there is a risk of damage which is not

covered by the warranty.

l All eventual electric installation has to be

carried out by a qualified electrician. The

installation of the hood should be made by a

person with enough knowledge. Installation

made otherwise could lead to loss of perform-

ance and even injuries and /or damage on

properties.

l The hood cannot be connected to flues of other

appliances that run on energy sources other than

electricity.

Please, keep to the provisions of official direc-

tives regarding the question of fumes discharge.

l When the hood is used at the same time of other

appliances that run on energy sources other than

electricity, provision must be made for an

adequate supply of air.

l When installed, the hood must be not less than

65 cm. above electric burners or 75 cm. above

gas or mixed-fuel burners. (Fig. 3).

l The power cord should be drawn so that there is

no risk of damage. Hazard!

At use of cooker hood

l No food must be cooked flambee underneath the

hood.

l The use of an unprotected flame is dangerous

for the filters and could cause fires.

l Never leave the deep-frying or frying pan over a

cooker/hob. The oil contained in the pan may

spontaneously ignite through overheating.

l Observe the filter change or cleaning intervals.

Failure to observe these intervals may cause the

risk of fire through fat deposition.

Note! If a fire starts; Switch of the cooker hood

and the heating zone; Cover the fire , Never use

water.

At disposal

l Help to avoid damages even when the cooker

hood should be disposed. Disconnect the power

plug and cut the power cord at hood inlet. Check

with the authorities for information of how to

proceed for disposal.

45

A.Motor and lamp switch panel

B.Metal filter grill (grease filter)

C.Housing cover

D.Hob light

Standard accessories included:

l Screws for mounting

l Duct with no return valve

Function

The hood may be used as follows:

- For air exhausting

- For air recycling

Exhausting

The air is vented outside by means of pipes to be

connected to the duct supplied (bajonet coupling +

fixing screw) with no return valve (Fig. 2) on top

side of the hood.

Attention! In the horizontal runs the duct must be

slightly slanted (about 10°) and directed upwards

to vent the air easily from the room to the outside.

The hood cannot be connected to flues

of other appliances that run on energy

sources other than electricity.

Recycling

The air is filtered through a carbon filter and

recirculated into the room. The filtered air is

discharged by means of a Ø120 mm pipe which

goes through the cupboard and whose outlet is

above the cupboard.

This version is used when there is no exhaust duct

for venting outdoors or when it is impossible to

install one.

Description of the appliance

Special accessories

Active carbon filter

When the hood is used in recirculation mode an

active carbon filter should be used.

Order by the retailer

PNC 955 101 116 (B,CH,D,Sk)

941 196 401 (P)

Fig. 1

A

B

C

D

Fig. 2

Ø 120mm

0

1

2

3

A

46

Unpacking

Check that the cooker hood has no damages.

Transportation damages should immediately be

reported to the one responsible for the transport

Damages, faults and eventually missing details

should immediately be reported to the seller.

Take care of the packing material so that small

children cannot play with it.

Placement

The hood is to be mounted in a wall cupboard.

When installed, the hood must be not less than 65

cm. above electric burners or 75 cm. above gas or

mixed-fuel burners. (Fig. 3).

Electrical connection

The hood has a power cord with moulded plug

with earth connection to be connected to a wall

outlet of 230 V.

The power cord length is 1,2 m.

Mounting of hood

l Fit the 120 mm air outlet connector with no

return valve (bayonet connection, one half turn

to the right) (Fig. 4).

l Remove the metal grease filter grill. Fold the

grips upwards and press the locking slide in at

the side(Fig. 5).

l Take the housing cover off by pressing the two

spring clips (Fig. 6).

l Fit the extractor hood into the opening in the

cabinet and press it upwards in such a way that

two springs (1-Fig. 7) on the side notch into

place above the supporting plate.

l Tighten screws (2-Fig. 7).

l The housing can be further fastened to the

cabinet with the four 2,9 x 16 mm screws.

l Replace the housing cover and clip in the metal

grease filters.

Installation

Min

75 cm

Min

65 cm

Fig. 3

Fig. 4

Fig. 5

Fig. 7

Fig. 6

47

Fig. 8

Exhausting mode

l Connect the air outlet to the smoke exhaust

hose.

l On the version EFG 732 X check that the two

internal shutters S (Fig. 8) are open.

Recirculation mode (with carbon

filter)

l Remove the metal grease filter grill.

Fold the grips upwards and press the locking

slide in at the side (Fig. 5)

l Fit the carbon filter into the lamp side 1 (Fig. 9)

by pressing the two red lugs, 2, of the filter in

and clip the filter in upwards into the hood.

l Refit the metal grease filter.

l The current of air is to be diverted forwards or

sideways into the room in a suitable fashion.

l The hood with the denomination EFG 732 X has

two internal shutters S (fig. 9) behind the grease

filter. These are at delivery open. Before mount-

ing the carbon filter they should be shut.

Important to know

If the hood is run at the same time as a burner or

fireplace that depend on ambient air (for example

gas, Diesel, coal or wood heaters, water heaters,

etc.) be careful, because the hood, when it exhausts

the air, removes the ambient air required by the

burner or fireplace for combustion.

Not valid if the cooker hood is used in

recirculation mode.

Fig. 10

Speed regulation

The hood has a three speed motor

regulated with a slide switch. For

the best performance, we recom-

mend using the lower speeds in

normal conditions and the highest

speed in particular cases of strong

odour and vapour concentration.

We recommend starting up the

hood a few minutes before cook-

ing and keeping it running until all

the odours have been eliminated.

Work light

The hood work light is independently switch on

and off with the proper push-button switch.

Correct ventilation

To have the cooker hood working correctly the

windows in the kitchen should be closed. In stead a

window in an adjacent room should be open.

0

1

2

3

Using the hood

Fig. 9

1

2

S

48

Maintenance

Before performing any maintenance

operation, disconnect the hood from

the electricity.

Grease filter

This serves to hold the grease particles in suspen-

sion. The metal filter should be washed every

month with warm soapy water or, if possible, in the

dishwasher (60°C).

To remove the metal grease filter, fold the grips

upwards and press the locking slide in at the side

(Fig. 5). Leave to dry before refitting it.

l (Only EFG 732): remove central plastic strip Z

to free the two filter panels (Fig. 11).

Clean the panels support as well.

Carbon filter

This filter dissolves cooking odours.

It should be changed every 6-8 months in normal

use. The carbon filter must never be washed.

To exchange the carbon filter:

l Remove the grease filter

l Take the old carbon filter out by pressing in the

two red lugs (2-Fig. 9) and pull it out forwards.

l Fit the new carbon filter first on the lamp side of

the hood (1-Fig. 9), press the two red lugs of the

filter and clip the filter upwards into the hood.

l Refit the grease filter.

Attention

Failure to observe the rules for cleaning the appli-

ance and changing and cleaning the filters may

cause fires. Therefore, we recommend observing

these instructions.

Cleaning

To clean the outside of the hood use a cloth mois-

tened with denatured alcohol or neutral liquid

detergents. Never use products containing

abrasives.

Changing the lighting elements

l Disconnect the hood from the electricity.

l Open the light cover by turning the latches

counterclockwise 1 (Fig. 12 and 13).

l Pull the old lamp out of the holder and replace it

with a new of same rating

EFG 732 X has 2 PL lamps of 9 W (Fig. 12).

EFG 532 X has 1 PL lamp of 11 W (Fig. 13).

Fig. 12

Fig. 13

Z

Fig. 11

49

If the hood does not function

Before you make contact to service

Check that the power plug is connected to the wall

power outlet and that no fuse is blown. Do not do

any operations that can cause hazard or damage to

the product. If the problem remains contact your

dealer or an approved service company

Remember to save the purchase recite and the

Warranty card (only used in some countries)

Service and spare parts

Service and spare parts you will get via your dealer

or service company.

When you order service or spare parts you should

be ready to give the product number and model

denomination. This information you will find on

the rating label.

Take away the grease filter and you will find the

rating label behind.

Model:

Product number:

Date of purchase:

Demounting of the hood

l Remove the metal grease filter and the housing

cover.

l Remove the 4 additional screws from the frame.

l Loosen the screws on the two fixing springs

(Fig. 14).

l Push a flat screw driver into the hole for the

fixing springs (left and right) and push each of

the fixing springs inwards (Fig. 15).

l At the same time, pull the hood (left and right)

out of the cabinet.

Fig. 14

Fig. 15

50

Technical data

Model EFG 732 X EFG 532 X

Capacity Max 450 m

3

/h

x)

286 m

3

/h 450 m

3

/h

x)

286 m

3

/h

Min. 197 m

3

/h 197 m

3

/h

Dimension Height 302 mm 302 mm

Width 748 mm 548 mm

Depth 302 mm 302 mm

Light 2 x PL 9 W 1 x PL 11 W

Grease filter 1 pc 1 pc

Mains Voltage 230 V 230 V

Electric safety class Class 1 Class 1

Power rating total 204 W 197 W

x)

Valid when the hood is used with carbon filter (recirculation)

EFG 732 X dimensions

710

4,5

748

70

160

283

302

510

4,5

548

70

160

283

302

EFG 532 X dimensions

Page is loading ...

Electrolux EFG 732 User manual

This manual is also suitable for

Electrolux EFG 732 User manual

in other languages

Related papers

Other documents