Western MVP 3 T-Frame Installation guide

Western
Brand
Western
Model
MVP 3 T-Frame
Type
Installation guide

Western MVP 3 T-Frame

The Western MVP 3 T-Frame is a versatile snowplow attachment that can be used for a variety of snow removal tasks. It is designed to be easy to install and use, and it can be used with a variety of vehicles. The T-Frame is made of durable materials and is built to last.

The MVP 3 T-Frame is perfect for clearing snow from driveways, parking lots, and other areas. It can also be used for commercial snow removal applications. The T-Frame is available in a variety of sizes to fit different vehicles and needs.

Here are some of the benefits of using the Western MVP 3 T-Frame:

Western MVP 3 T-Frame

The Western MVP 3 T-Frame is a versatile snowplow attachment that can be used for a variety of snow removal tasks. It is designed to be easy to install and use, and it can be used with a variety of vehicles. The T-Frame is made of durable materials and is built to last.

The MVP 3 T-Frame is perfect for clearing snow from driveways, parking lots, and other areas. It can also be used for commercial snow removal applications. The T-Frame is available in a variety of sizes to fit different vehicles and needs.

Here are some of the benefits of using the Western MVP 3 T-Frame:

Lit. No. 43114, Rev. 00 1 June 1, 2013
INSTALLATION INSTRUCTIONS
Pushbeam Installation
1. Park the vehicle on a smooth, level, hard surface,
such as concrete. Lower the blade to the ground,
and turn the control to the "OFF" position.
Disconnect the snowplow from the vehicle, or
turn the vehicle ignition to the "OFF" position and
remove the key.
2. Align the front holes in the pushbeam with the
front holes in the T-frame. Loosely fasten with two
3/4" x 2-1/2" carriage bolts* and 3/4" locknuts.
A DIVISION OF DOUGLAS DYNAMICS, LLC
Western Products
PO Box 245038
Milwaukee, WI 53224-9538
www.westernplows.com
43116
T-Frame Service Kit
Installation Instructions
CAUTION
Use standard methods and practices
when attaching snowplow and installing
accessories, including proper personal
protective safety equipment.
CAUTION
Read this document before installing the
T-Frame Service Kit.
WARNING
Do not exceed GVWR or GAWR, including
blade and ballast. The rating label is found on
the driver-side vehicle door cornerpost.
3. Align the rear holes in the pushbeam with the rear
holes in the T-Frame and fasten in the middle
position using two 3/4" x 2-1/2" carriage bolts* and
3/4" locknuts. Tighten until assembly is secure, but
do not torque at this time.
4. Assemble the rest of the snowplow.
5. Check that the T-frame is parallel with the ground
as described in Step 1 under "Leveling Adjustment
Procedure."
3/4" Locknut
3/4" x 2-1/2"
Carriage Bolt*
* 3/4-10 x 2-1/2 Hex Cap Screws (PN 90459) are required
when attaching the T-frame to a push assembly with round
holes instead of square holes.
3/4" Locknut
3/4" x 2-1/2"
Carriage Bolt*
Lit. No. 43114, Rev. 00 2 June 1, 2013
Western Products reserves the right under its product improvement policy to change construction or design details and furnish equipment when
so altered without reference to illustrations or specifi cations used. Western Products or the vehicle manufacturer may require or recommend
optional equipment for snow removal. Do not exceed vehicle ratings with a snowplow. Western Products offers a limited warranty for all
snowplows and accessories. See separately printed page for this important information. The following are registered (®) or unregistered (™)
trademarks of Douglas Dynamics, LLC: UltraMount® 2, WESTERN®.
Printed in U.S.A.
Leveling Adjustment Procedure
1. With the snowplow attached to a properly ballasted
vehicle and the blade lowered to the ground, the
T-frame should be parallel with the ground.
If the T-frame is parallel with the ground, go to
Step 4.
If the T-frame is not already parallel with the
ground, place the snowplow in the scoop position
and follow Steps 2–4.
2. Loosen the front fasteners connecting the
pushbeam to the T-frame, but do not remove
them. Next, remove the rear fasteners connecting
the pushbeam to the T-frame. Level the T-frame
so its parallel with the ground.
3. Select the hole in the rear of the T-frame that is
aligned closest to the rear holes in the pushbeam.
Reassemble the previously removed fasteners into
the rear holes.
4. Lubricate and tighten all fasteners to 250 ft-lb.
Front
Fasteners
Rear Fasteners
T-Frame
Push
Beam
Select the hole best
aligned with rear holes
in push assembly
  • Page 1 1
  • Page 2 2

Western MVP 3 T-Frame Installation guide

Western
Brand
Western
Model
MVP 3 T-Frame
Type
Installation guide

Western MVP 3 T-Frame

The Western MVP 3 T-Frame is a versatile snowplow attachment that can be used for a variety of snow removal tasks. It is designed to be easy to install and use, and it can be used with a variety of vehicles. The T-Frame is made of durable materials and is built to last.

The MVP 3 T-Frame is perfect for clearing snow from driveways, parking lots, and other areas. It can also be used for commercial snow removal applications. The T-Frame is available in a variety of sizes to fit different vehicles and needs.

Here are some of the benefits of using the Western MVP 3 T-Frame:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents