Page is loading ...
2-WAY COMPONENT SPEAKER
NS6-Q2
User Manual
www.nakamichicaraudio.com
PRODUCT INFORMATION
WHAT’S IN THE BOX
INSTALLATION
Check and identify the contents of your package:
Tweeter
20
102
30
42
4
89
800Hz20KHz
ASV 25mm
-
Woofer
75
140
1530
75
4
88dB±3dB
50Hz8KHz
KSV 35mm
20
Specifications
RMS.Power(W)
Mounting Diameter(mm)
Net Mass(g)
Mounting Depth(mm)
Sensitivity@1w/1m(dB)
Frequency Range
Nominal lmpedance(Ω
Voice Coil
Magnet Mass(Oz)
6. Network (x2);
7. 2.5mm “L” Type Wrench (x1);
8. 3.0mm “L” Type Wrench (x1);
9. Mounting Screw M3x10mm (tweeter) (x6);
10. Mounting Screw M4x30mm (woofernetwork) (x16);
1. Installation Manual (x2);
2. Woofer (x2);
3. Woofer’s Grille Net + Frame (x2);
4. Tweeter (x2);
5. Tweeter’s Back Cover (x2);
Fig.1
Fig.2
Fig.3 Fig.4
Y ou can mou n t the woof er s on the f r ont /r ear door of you r car .
Option 1 : Mount the woofer on door (front or rear)
★
★
★
M ake s ure that nothi ng obs tructs around the mounti ng l ocation of the door.
A hol e for mounti ng may already be cut out of the i nner panel of the door(front or rear) . In this care, y ou need to modify the board onl y .
E ns ure that the s peaker termi nal s, frame or m agnet do not i nterfer
e wi th any i nner parts, s uch as the wi ndow) , etc. A l s o ens ure
that the speaker gri l l e does not touch any i nner fi tti ngs , s uch as the wi ndow cranks, door handl es , arm res ts etc.
1. Tu r n off the car ign it ion key.
★ I f the power i s on, the cl i ck noi se generated by the connecti on may damage the s peakers .
2. Cu t ou t the moun tin g t emplate f r om t he packing box.
3. P aste t he template on the location
select ed f or mou ntin g the speaker.
4. M ar k th e cu t- of f hol e an d th e 4 bolt hol es. (Fi g.1)
5. Cu t ou t the mar ked ar ea an d dr il l t he bolt h oles. (F ig.2)
6. R emove th e gr il le n et . (Fi g.3)
7. Con nect t he woof er s to th e n etwor k or car au di o.
(See ’How t o complete th e wir ing.’)
8. M oun t on th e speaker as sh own below. (Fig.4)
9. P r ess an d in ser t the edges of the gr ille n et.
★ T he s peaker gri l l e can be mounted wi thout the gri l l e net, i f y ou l i ke.
HOW TO COMPLETE THE WIRING.
★ Consult the diagram below. Be sure to connect corresponding terminals, i.e. ''+'' to ''+'' and ''-'' to ''-''. Connection
with reversed polarity will degrade the quality of production.
★ Connect the provided speaker cord to the speaker terminal while holding the lower portion of the speaker terminal.
Connect the woofers and the tweeters to the 2-way crossover network first, then connect the network
to your amplifier or car audio directly.
You can also mount the speakers into the surface of the rear tray.
Follow the steps in section “Option 1: Mount on door” to mount the speakers into the rear tray.
Option 2: Mount the woofer on rear tray
Follow steps mentioned in “Mount the woofer” section to mount tweeter.
Find a proper location to mount the tweeter. Mount the tweeter onto the car with the supplied screws.
Mount Mid-range and Tweeter
Option 1 Option 2
★Find a proper location to mount the networks.
★Mount the networks onto the car with the supplied screws.
MOUNT THE NETWORK
Option 2
Option 1
Amplifier
Woofer
Tweeter
IMPORTANT
Read and understand all instructions before you use the apparatus. If damage is caused by failure to follow instructions,
the warranty does not apply.
Use only the supplied mounting hardware for a safe and secure installation.
Do not continuously use the speaker system beyond the peak power handling capacity.
Keep credit cards, watches, recorded tapes etc. with magnetic coding away from the speaker system to prevent damage
caused by the magnets in the speakers.
Clean the apparatus with soft, damp cloth. Never use substances such as alcohol, chemicals or household cleaners on
the apparatus.
DIMENSIONS (UNIT:MM)
Woofer
Φ140mm
Φ166mm
Φ171mm
Φ4mmx4
74.5mm
Tweeter
Φ58mm
Φ58mm
Φ42mm
Φ6mm
30mm
35mm
★ Design and specifications are subject to change without notice.
Network
110mm
170mm
45mm
/
