JVC LVT1238-002A User manual

JVC
Brand
JVC
Model
LVT1238-002A
Category
Loudspeakers
Type
User manual

This manual is also suitable for

CAR STEREO SPEAKER
For Proper Installation and Use
If a kit is necessary for your car, consult your telephone
directory for the nearest car audio speciality shop ("IN-CAR
ENTERTAINMENT" dealer)
Thank you for purchasing the JVC Car Stereo Speakers. These
speakers can be mounted either in the doors or in the rear tray of
your vehicle. For the secure installation and perfect operation of your
speakers, please read the following carefully.
Specifications
Type : 16 cm (6-1/2") 2-Way Component Speaker, Door/
rear mounting
Power Handling Capacity : 150 watts (MAX. MUSIC POWER)
Impedance : 4 ohms
Magnet Mass : 256 g (9 oz)
Mass : 0.87 kg (2.00 lbs)
(Design and specifications are subject to change without notice.)
INSTRUCTIONS
CS-VS601
CS-VS601
CAR STEREO SPEAKER
1. Before connecting the speakers to the amplifier, confirm that the
power has been turned off. The click noise generated by the
connection if the power is on may damage the speakers.
2. The amplifier and speakers should be connected between
corresponding terminals, i.e. "left" to "left", and "right" to "right", as
well as "+" to "+", and "-" to "-". Connection with reversed polarity
will degrade the quality of stereo reproduction.
3. Do not subject the speakers to excessive input. The power handling
capacity of the CS-VS601 is 150 watts (Max. music power). Any
excessive input may damage the speakers.
4. The CS-VS601 has an impedance of the amplifier's speaker terminal
is rated at 4 ohms.
5. When cleaning the speakers, use a soft cloth and wipe the surface
gently. Do not apply thinner or solvent.
-
UNIT : mm
Dimensions
O1
42
4
-O4
.9
HO
L
ES
O179.3
43.8 21.9
O124
O80
LVT1238-002A
48.8
42.4
O50.5
18.5 9
O49.8
27.3
O58.8
Q/YXFJ105
JVC
(Victor Company of Japan, Limited)
JVC
68
Connection
How to Install
1. To install the speaker in the rear tray, first
determine the appropriate area in which to place
it. The speakers must be installed in a place
where there are spaces of at least 32 mm over
the tray and at least 49 mm under the tray. ln
determining the location, make sure that the
bottom part of each speaker fits into the large
hole in the steel plate on which the rear tray is
fixed.
2. Remove the rear tray.
3. The paper pattern printed on the bottom of the
packing box shows the exact shape of the area
on the rear tray through which the speaker will
be installed. Apply the paper pattern onto the
area determined in 1. above, and trace out the
shape of the area on the tray.
4. Then, cut out the marked area.
5. The next step is to wire the speakers. Be sure to
connect to connect corresponding terminals, i.e.
"left" to "left", "-" to" -", etc.
6. Use the tapping screw and speed nuts provided
to fix the speaker and grille to the rear tray. Match
the 4 screw holes in the speaker frame and the grille
to the holes in the rear tray, insert the 4 screws
in into the holes and secure them with 4 nut.
7. The process for installing the speakers in the
door is much the same as for installing the
speakers in the rear tray. ln this case, however,
extra care must be taken to install the speaker
out of the way of the door handle. lnstall the
speakers with the terminals down.
Amplifier
Woofer
Tweeter
Speed nut
(O4 mm)
x16
Black lined
Black lined
Network cord
x2
Speaker cord
x2
Speaker cord
x2
Amplifier
Midwoofer
Tweeter
2-WAY CROSSOVER NETWORK
12dB/Oct.
WOOFERINPUT TWEETER
2m 2m4m
Screw
x8
(O4x25mm)
Screw
x4
(O4x20mm)
Screw
x4
(O3.5x20mm)
Screw
x2
(O4x25mm)
Screw nut
x4
(O4mm)
1 2
3
4
5
6
7
8 9
7
11
8
9
Parts
10
1
6
x4
x4
Woofer Mounting
Network
x2
Grille Ass'y
10 11
2-WAY CROSSOVER N
ETW
ORK
12
dB/Oct.
WOOFE
R
INPU
T
TWEETER
Mounting bracket
x2
12
Angle adaptor
13
Fix frame
x2 x2
14
2-WAY
CRO
SSOVER NE
TWORK
12dB/
Oct.
WOOFER
INPUT
TWE
ETER
-3dB
0dB
Tweeter level adjust
-3dB
0dB
(-3dB)
-3dB
0dB
(-0dB)
Swivel Mounting
Flush Mounting
13
3
6
14
x2
x2
Tweeter Mounting
Angle Mounting
2-W
AY
C
RO
SS
OVER NETW
ORK
12
dB
/Oct.
W
OOFER
INPUT
TWEETER
11
Network Mounting
2-WAY CR
OSSOVE
R NET
WO
RK
12
dB
/Oct.
WOO
FE
R
INPUT
TWEETER
Surface Mounting
5
4
3
x2
6
x2
14
12
4
5
2
x2
6
x2
  • Page 1 1
  • Page 2 2

JVC LVT1238-002A User manual

JVC
Brand
JVC
Model
LVT1238-002A
Category
Loudspeakers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents