Acroprint ES1000 User manual

USER'S MANUAL

1

The details of this User's Manual are subject to change without previous notification.

This User's Manual has been prepared with the utmost care to cover all aspects of the time

recorder's use.

If you feel, however, that some explanations are inadequate, unclear, or difficult to

understand, please do not hesitate to contact Acroprint.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted,

in any form or by any means, mechanical, photocopying, recording or otherwise without

the written consent of Acroprint Time Recorder.

Place the time recorder at the position close to the wall outlet so that it is easily

accessible to disconnect.

1.

2.

3.

2

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his or her own expense.

Caution: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS A LIMITS FOR RADIO NOISE EMISSIONS

FROM DIGITAL APPARATUS AS SET OUT IN THE RADIO INTERFERENCE REGULATIONS OF THE

CANADIAN DEPARTMENT OF COMMUNICATIONS.

LE PRÉSENT APPAREIL NUMÉRIQUE N'ÉMET PAS DE BRUITS RADIOÉLECTRIQUES DÉPASSANT LES

LIMITES APPLICABLES AUX APPAREILS NUMÉRIQUES DE CLASSE A PRESCRITES DANS LE

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE ÉDICTÉ PAR LE MINISTÈRE DES

COMMUNICATIONS DU CANADA.

WARNING

Precautions

This user's manual is prepared for safe and proper use of the unit.

Please follow all the instructions to avoid possible danger to yourself or

others and damage to the unit.

Signs

Various warnings and cautions are provided throughout this manual along with signs.

Remember each sign and its explanation listed below for your safety and proper

operation of the unit.

Caution

Warning

Improper handling may cause electric

shock DANGER.

DO NOT disassemble the unit.

"Don't" sign.

"Must-Do" sign.

Be sure to remove the line cord plug

from the outlet.

Do not disassemble the unit. There is a high voltage present inside, possibly leading to an

electric shock.

Do not use any voltage of the power source other than designated.

Do not share a single outlet with another plug. These may lead to fire or shock hazards.

Do not damage, break, or modify the power cord. Do not put a heavy object on, pull, or

forcefully bend the cord, either. These may damage the cord, possibly resulting in a fire or

electric shock.

If any anomaly occurs, for example, heat or smoke is generated or an odor is emitted, unplug

the unit immediately and contact your dealer for servicing. There is a danger that further use

may cause a fire or electric shock.

Do not modify the unit. Modifications may cause a fire and/or electric shock.

Warning

Improper handling may cause bodily accidents including

death and serious injury.

Improper handling may harm the human body or material.

3

1

If foreign matter should get in the unit (including a piece of metal, water, or liquid), disconnect

the plug from the outlet immediately and contact your dealer for servicing. There is a danger

that further use may cause a fire or electric shock.

Do not place the unit on an uneven or tilted surface. This may result in injuries due to the unit

dropping or falling off.

Do not put a water-filled container or a metal object on top of the unit. If water is spilled or the

metallic object slips inside, a fire or shock hazard may occur.

Do not place the unit near kitchen counter or humidifier. Oil, smoke, or steam generating from

them may cause fire or shock hazards.

Do not yank the power cord to disconnect from the outlet. Hold the plug with your hand to do

so, or the cord may be damaged, possibly leading to a fire or electric shock.

Remove the line cord plug from the outlet before transferring the unit, or it may damage the

cord, possibly leading to a fire or electric shock.

Make sure to insert the power plug as far as it will go. Improper insertion of the plug may

develop fire or shock hazards.

Do not insert or drop any other time card than specified into the slot. Such misuse may cause a

fire or electric shock.

If the unit should be dropped or the case be broken, unplug the unit and contact your dealer for

servicing. Further use may lead to a fire or shock hazard.

Be careful not to contact the print head, as you may get hurt or burned.

Do not install the unit in a humid or dusty environment. It may cause a fire or electric shock.

Do not plug or unplug the unit with a wet hand. You may get an electric shock.

Caution

4

2

Table of Contents

Introduction and Features of the ES1000

Getting Started

Unpacking the ES1000

Overview

Installing the Ribbon Cassette

Wall Mounting the ES1000

Where to Install the ES1000

Overview of Operation

What You Can Do with the ES1000

Settings

Preparation for Setting

Overview of Function Buttons

Setting the Hour Display Format

Setting the Time

Setting the Date

Setting Pay Period and Pay Period Ending Date

Monthly

Weekly

Bi-Weekly

Semi-monthly

Setting the Day Advance Time

Selecting the Print Format

Enabling Override and Transfer Functions

Selecting Rounding Rules

Schedule (Setting Calculation Rules)

Setting the Schedule

Free Zone or Open Shift (easy and most popular)

Time Zone or Fixed Shift

(ideal when everyone is on the same schedule)

Overtime Calculation

Round and Grace Time for Start/End Time (ST/ET)

Setting the Weekly Program for External Time Signal

Setting the Auto Daylight Saving Change

Selecting the Language

Setting the Password

1.

2.

3.

4.

1

2

3

5

6

7

11

12

13

14

15

16

17

18

19

20

21

22

23

25

26

30

37

42

45

48

52

53

5

Printing Hours Summary

Printing List of Active Card Numbers

Printing List of Program Settings

Additional Features

Override Printing

Card Transfer

Card Resetting

All Cards Resetting

Resetting

Installing the Optional Battery Backup

Connecting External Signal Control

Troubleshooting

Specifications

5

6.

7.

8.

9.

10.

11.

12.

13.

57

58

59

60

61

63

64

65

66

68

69

For accessories, visit Acroprint on-line

at www.acroprint.com or

call 800.334.7190 or (919) 872.5800 (outside the USA)

6

1. Introduction and Features of the ES1000

The ES1000 Totalizing Time Recorder provides fast, easy and accurate

calculations of your employee hours worked. The ES1000 can handle a

Weekly, a Bi-Weekly, a Semi-Monthly or a Monthly pay period for up to 100

employees. The recorder can be programmed to print late in or early out

punches in "RED". This state-of-the-art totalizing recorder offers a program for

an external signal (Bell/Horn, not included) and an optional full operational

battery back up for punching without AC power.

The ES1000 allows for the selection of two sets of calculating rules:

Free Zone or "Open Shift" rules permits employees to punch IN and OUT

without being assigned to a fixed schedule. Employee's times are calculated

using elapsed time or punched IN time subtracted from punched OUT time.

Using this selection is the easiest and most popular form of totalizing

employee's hours worked.

Free Zone allows for Auto Lunch deduction and permits you to select the

length of the break. You may also choose the number of regular hours worked

before overtime is calculated. You may also select the maximum hours an

employee is on the clock when it would be considered a "forgotten" out punch.

Using the Free Zone calculating rules will permit easy, accurate totalizing of

your payroll hours.

Time Zone or Fixed Schedule rules are designed for companies that have all

employees on one assigned shift. Time Zone rules allows for assignment of

"start" and "stop" times of the shift with GRACE times with early or late

punches printing in RED. Time Zone permits three break periods.

Time Zone rules may also be used with Free Zone rules under certain

circumstances. Taking advantage of all these advance features will require

additional programming time but will offer an advance time and attendance

system.

7

1

Overview

2. Getting Started

Unpacking the ES1000

Operation Manual

Wall Mount Screws, Brackets

and Template

Ribbon Cassette

Keys

8

Wall-mounting holes

Front cover

Display

Function buttons

Key hole

Card slot

External signal and full

operation battery (optional)

compartment

2

Installing the Ribbon Cassette

1

Unlock cover and pull up the top

side of the card insertion slot and

pull it towards you.

2

Turn the knob on the cassette in the

arrow-indicated direction to make the

ribbon taut.

3

To insert the ribbon cassette inside

the unit, thread the ribbon between the

ribbon mask and the print head (See

drawing next page). Slide the clasps

on the lower side of the cassette into

projections on the unit.

Keep on pushing in the ribbon cassette

until the clasps at both sides catch and

the cassette snaps into position. If it is

difficult to insert the ribbon cassette,

try it while turning the knob.

Knob

Clasp

Print head

Make sure the power is on before installing.

9

Front Cover

Projection

3

Take the following precautions when inserting a new ribbon cassette.

Install the ribbon cassette so that the ribbon is between the

print head and the

ribbon mask (see the figure on the left). Printing failure may occur if the ribbon is

placed behind the ribbon mask (see the figure below).

4

Precautions to take when replacing the ribbon

65

Replace the cover by fitting the tabs at

the bottom of the cover into the holes

located on the clock.

Then close the cover letting it snap

into place.

Turn the knob of the ribbon cassette in

the counter clockwise to tighten the

ribbon.

Print head

Ribbon mask

Ribbon

Print head

Ribbon mask

Ribbon

10

4

Correct Incorrect

Wall Mounting the ES1000

The ES1000 may be platform or wall mounted using the wall mount screws supplied.

To mount unit on wall, take the following steps:

The supplied screws

are intended for use

on a thick wooden

wall or wooden

column. Do not use

them on any other

materials. There is

a danger that the

unit may come off if

used on other

materials.

Install wall mount screws (supplied) into a wall 3.94 inches (10 cm) apart.

Be sure to keep about 0.12 inch ( 3 mm) of the screw head out of the wall.

You can use a supplied template to fix position of two screws.

Where to Install the ES1000

Avoid placing the unit in environments that are:

• humid or dusty

• exposed to direct sunshine

• subject to frequent or continuous vibrations

• outside the temperature range between -5˚ and 45˚ C (23˚ to 113˚F)

• affected by chemicals or ozone

Mount the wall mount

brackets as shown on the

right.

1

2

11

5

0.12"(3mm)

3.94" (10cm)

Wall Mount Template

Wall

Screws

Once the AC line cord is plugged into the outlet, the unit can be used immediately. Basic

operations, including the time and ending dates, are preset.

The ES1000 is designed to work only with the ES1010 Time Cards. The clock will not

function correctly using other style time cards, and using other cards may cause damage to

sensors.

Do not let any metallic object get into the slot, including paper clips. Do not

forcefully push in a card, either. These may cause the unit to malfunction.

3. Overview of Operation

It is easy to operate the unit. Just insert a time card. To start a time card, make sure the

"number" on the card faces outward (towards operation). The card is then automatically

pulled in, printed and then ejected.

When a new card is inserted, the card will automatically be registered, and will print the

"IN" print on the first line. The month will be printed on the first line also or on the line

when the month and printing line change.

You can print "IN" and "OUT" as many times as you want per day. Concerning the printing

line, it will slide one line down each time you insert the card for "IN" print.

The recorder will record the last imprint and automatically switch the "IN" and "OUT".

You may also manually switch the column position of imprint by pushing the "IN" button

or "OUT" button.

The number of cards that can be automatically registered is a maximum of 100 cards.

Card numbers 001 through 100 using duplicate numbers can cause incorrect totals.

See "2. Getting Started".

Even if the "IN" is printed, when the present time passes the "Day Advance Time", it will

consider that the "OUT" print was forgotten and will print the "IN" print on the next line.

12

6

Schedule [Time Zone Rule]

You can select days of the week which your desired schedule is applied to. All other days of

the week will be regarded as "weekend or non-scheduled work days", which you can set

threshold hours and duration of auto break deduction.

Based on the programmed schedule, you can regulate the day's working rules. The day's

partition that is the schedule's standard is the "Day advance time", and this time is selectable.

[Applicable days of the week]

Example: From Monday to Friday

What You Can Do With the ES1000

13

7

IN

Day

advance

time

red red red

7:30 a.m.

START

8:00 a.m. 1:00 p.m.12:00 p.m. 3:15 p.m.3:00 p.m.

END

5:00 p.m.

02 Start time for

irregular printing

(black red)

Break time 1 Break time 2

Day

advance

time

Printed

in black

* Any punch during "break time" will be printed in black regardless of settings.

* Break time will be deducted from worked hours automatically.

Printed

in black

(If you set the Break #3, set 14 and 15 also.)

* All punches are printed in black.

Note: Numbers in square mean program numb

er.

[Non-selected days of the week]

Example: Saturday and Sunday

16 Threshold hours for auto

break deduction

17 Duration of

break time

Worked more

than 4 hours

Break time

(= 30 min.)

Worked hours

( = 4 hours)

Worked hours

03 End time for

irregular printing

(red black)

OUT

5:05 p.m.

IN

8:30 a.m.

OUT

3:30 p.m.

12 Start time

of Break #2

10 Start time

of Break #1

13 Duration in

minutes,

Break #2

11 Duration in

minutes,

Break #1

In addition to the start time and duration for the maximum settings of three "break times",

the following settings are available to fulfill your needs.

Start and End Time for Irregular (Red) Printing

Once you set the schedule for irregular printing, printing color automatically changes

according to the start/end time you've set. Color change makes it possible to easily see an

employee's late in or early out.

* Note: Any punch during break time will be printed in black regardless of the above setting.

Regular Hours and Overtime

You can select calculation type from the following four choices according to how to divide

and calculate "regular hours" and "overtime" when you selected "time zone" rule.

Semi-monthly and Monthly pay period overtime calculations are based on daily overtime

only. To assure accurate calculations for these pay periods, please select daily regular hours

limit as desired, and select " " as the limit for weekly regular hours. This will "disable"

the weekly OT function so that the clock will calculate properly.

[Type 1]

Basically all worked hours are accumulated as regular hours.

14

8

IN OUT RH OT OTRH

Au Mo 9:00A Mo 6:00P

Tu 8:00P