3M Cold Shrink QS4 Integrated Splice QS4-35TS-QCI-350-750 Operating instructions

Brand: 3M

Model: Cold Shrink QS4 Integrated Splice QS4-35TS-QCI-350-750

Type: Operating instructions

This manual is also suitable for

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

™

Cold Shrink QS4 Integrated Splice

Kit QS4-35TS-350-1000

for TapeShield, Wire Shield, UniShield

, and

Longitudinally Corrugated (LC) Cable

Instructions

IEEE Std. 404

35 kV Class

250 kV BIL

F CAUTION

Working around energized systems may cause serious injury or death. Installation should

be performed by personnel familiar with good safety practice in handling electrical

equipment. De-energize and ground all electrical systems before installing product.

Kit Selection Table

Kit Number Cable Insulation O.D. Range Min. Cable Jacket O.D. Conductor Size Range

QS4-35TS-350-1000

1.24" - 2.07"

(31,5 - 52,6 mm)

1.78"

(45,2 mm)

350 - 1000 kcmil*

(185 - 500 mm

)

* Splices (including size transitions) can be made to smaller or larger conductors (but larger conductors may require special neutral

handling), provided both cables are within the Insulation O.D. Range and the connector meets the dimensional requirements

shownbelow.

Connector Dimensional Requirements

Minimum Inches (mm) Maximum Inches (mm)

Outside Diameter 0.87" (22,1 mm) 2.07" (52,6 mm)

Length

Aluminum (Al/Cu) Compression

—

7.50" (191 mm)

Length

Copper (Cu) Compression and 3M

™

Shearbolt Connectors

QCI 350-750 and QCI 500-1000

—

8.25" (210 mm)

July 2016

78-8127-8892-1 Rev B 3

2 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

1.0 Kit Contents

a. 3M Cold Shrink QS4 Integrated Splice Body QS4-35TS-350-1000 (1 ea.)

b. Constant Force Springs (5 ea.)

c. 3M Red Compound P55/R Tubes (non-silicone grease) (2 ea.)

d. Scotch

Rubber Mastic Tape 2228 Rolls, 2" x 36" (2 ea.)

e. Scotch

Mastic Strips 2230, 6" length (6 ea.)

f. Cold Shrink Adapter Tube (1 ea.)

g. 3M EMI Copper Foil Shielding Tape 1181 Strips, 1/2" x 10" (2 ea.)

h. Ground Strap (1 ea.)

i. 3M Cable Cleaning Pads CC-3 (1 ea.)

j. Cut-back Templates (2 ea.)

k. Wire Brush (1 ea.)

l. Instruction Booklet (1 ea.)

Note: Cold Shrink adapter tube may not be included in all kits.

Note: Kits contain either 1 or 2 cut-back templates as needed per conductor size.

Note: Do not use knives to open plastic bags.

Note: Connector not shown, but if included, it is indicated on the packaging label.

78-8127-8892-1 Rev B 3

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

2.0 Prepare Cables

2.1 Check to be sure the cable fits within the kit ranges as shown on the cover page.

2.2 Prepare cables according to standard procedures. Refer to template provided or illustration below for proper

dimensions (Figure 1).

[ B ]

[ A ]

3 1/2"

(89 mm)

(76 mm)

Cable Jacket

Metallic

Shield

Semi-con

Insulation

[ B ]

[ A ]

3 1/2"

(89 mm)

Cable Jacket

Wire Shield

Semi-con

Insulation

[ B ]

[ A ]

Insulation

Shield Wires

3 1/2"

(89 mm)

Tape & LC Shielded Cables

Wire Shielded Cable

UniShield

Cable

Figure1

Typical Conductor Size*

kcmil (mm

)

Insulation OD Range

Inches (mm)

Jacket Cutback "A"

Inches (mm)

Semi-con Cutback "B"

Inches (mm)

350**-500

(185-300)

1.24-1.70”

(31,5-43,2)

15 3/4”

(400 mm)

9 1/4”

(235 mm)

750-1000**

(325-500)

1.59-2.07”

(40,4-52,6)

15 1/4”

(387 mm)

8 3/4”

(222 mm)

*For 100% and 133% insulation levels, Insulation OD is the ﬁnal determining factor.

**Cables must be within the Insulation OD Range of the splice kit and the connector must meet the dimensional requirements shown on the front page.

4 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

2.3 Secure end of each metallic shield or wires with a copper tape strip (Figure 2).

Cable Jacket

Wire Shield

Semi-con

Insulation

Shield Wires

Wire Shielded Cable

UniShield

Cable

Tape & LC Shielded Cables

Foil Tape

Semi-con

Insulation

Metallic Shield

Cable Jacket

Foil Tape

Figure2

2.4 Clean or cover cable jacket 30" (760 mm) from jacket edge on side where splice body will be parked.

2.5 Slide integrated splice body onto clean cable jacket (Figure 3).

Loose core end

Integrated splice body

Cleaned cable jacket

Figure3

78-8127-8892-1 Rev B 5

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

3.0 Install Connector

Note: If using a crimp-type connector, go to step (3.3).

3.1 If using a 3M Shearbolt Connector QCI 350-750 or QCI 500-1000, refer to the instructions included with

the connector for insulation cut-back dimension. Insulation removal length shall not exceed 3 3/4" (95 mm) from

conductor end (Figure 4).

Refer to connector instructions for dimensions

Figure4

3.2 Install 3M Shearbolt Connector QCI 350-750 or QCI 500-1000 according to the instructions included with the

connector (Figure 5).

Connector

Shearbolt

Figure5

Go to section 4.0 “Install Splice.”

6 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

3.3 If using a crimp type connector, remove cable insulation for 1/2 connector length plus an allowance* for

increases in connector length due to crimping. Insulation removal length shall not exceed 4 1/8" (105 mm) from

conductor end. Do not install connector now (Figure 6).

*Note: This assumes that the installer has determined the increased length of an aluminum connector crimped with

a specific tool and die.

Aluminum (Al/Cu) Crimp Connector Growth Chart

Conductor Size Typical growth allowance (per end)

350 - 500 kcmil 1/4" (6 mm)

750 - 1000 kcmil 3/8" (10 mm)

Note: 1) Copper connectors do not require a length change allowance.

2) Maximum aluminum connector crimped length allowed is 8.25" (210 mm).

One-half connector length

+ growth allowance*

Figure6

3.4 For 350 through 1000 kcmil copper connectors, 350 through 750 kcmil aluminium connectors or

connectors with an O.D. between 0.87 - 1.60" (22,1 - 40,6 mm): Park the cold shrink adapter tube on the

insulation. (Figure 7)

Cold shrink adapter tube

Figure7

78-8127-8892-1 Rev B 7

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

3.5 Install connector. See table (on cover) for proper connector dimensions. (For standard 3M

Connectors, refer

to table at the end of this instruction for crimping information). If using an aluminum conductor, wire brush

aluminum strands and then insert into connector. Remove excess inhibitor compound and remove conductor from

connector. Wire brush aluminum strands again. Insert into connector and crimp. Remove any excess oxidation

inhibitor from connector ends (Figures 8 and 9). File sharp connector flashing, if necessary, taking care to

remove all metal filings from splice area.

Antioxidant Compound

Figure8

Connector

Figure9

4.0 Install Splice

4.1 Apply a tape marker to semi-con insulation shield on cable which does not contain splice. Measure 11 1/4"

(286 mm) from center of connector (Figure 10).

Tape Marker

Semi-con

11 1/4"

(286 mm)

Figure10

8 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

4.2 If using cold shrink adapter tube: Position adapter tube over the connector. Shrink adapter near the center of

connector by pulling and unwinding the loose core end in a counterclockwise direction

(Figure 11)

Cold shrink adapter tube

Figure11

4.3 Clean cables using standard practice:

a. Do not allow solvent or abrasive to contact the cable semi-conductive insulation shield.

b. Do not reduce cable insulation diameter below 1.24" (31,5 mm) specified for the splice.

c. The insulation surface must be round, smooth and free of cuts/voids. Sanding may be necessary, finish

sanding should be done with a 120 grit or higher electrical grade abrasive.

d. Make certain that the cable insulation is smooth, clean and dry before continuing.

4.4 Apply 3M Red Compound P55/R on cable insulations, making certain to fill in edge of cable semi-con. Do not

use silicone grease (Figure 12).

Apply

™

Red

Compound P55/R

Apply

™

Red

Compound P55/R

Fill semi-con step Fill semi-con step

Figure12

78-8127-8892-1 Rev B 9

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

Note: This core installs differently than other cold shrink products.

4.5 Position the splice body over connector area, aligning end of the splice body (not the core) at the center of the tape

marker. Slowly start to remove the splice core by pulling and unwinding the loose core end counterclockwise,

allowing only ¼" (6 mm) of the splice to shrink onto the tape marker. Carefully slide the splice body off the tape

marker by pulling and twisting until the entire tape marker is exposed. Continue removing the core to complete

the splice body installation (Fig ure 13).

Note: The splice body ends must overlap onto the semi-con of each cable by at least 1/2" (13 mm).

Note: Do not push the splice body toward the tape marker as this may cause the end to roll under. If the end does

roll under, DO NOT use sharp-edged tools to pull it out as this could cut and damage the splice.

Unwind Counterclockwise

Align splice body with tape marker

Figure13

5.0 Connect Shielding

5.1 Remove the vinyl tape holding the shield sleeve on the rejacketing tube, and spread the shield sleeve out toward

the cable jacket.

5.2 Hand-tighten the shield sleeve outward and secure it to the wires, tape or LC shields on either side of the

splice using two constant force springs on each end between the jacket edge and the copper foil tape as shown

(Fig ure 14).

Note: If using a ground strap for external grounding, leave room for a third constant force spring over the

shield sock at the jacket end. Refer to Step (6.1).

10 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

5.3 If shield sleeve extends beyond jacket edge, it may be interwoven with the constant force springs. Cinch (tighten)

the spring after wrapping the final winding (Fig ure 14).

Cable Jacket

Rejacketing Tube

Constant Force Springs

Foil Tape beneath Shield Sleeve

Figure14

5.4 Wrap two half-lapped layers of vinyl tape over all constant force springs (Figure 15).

Vinyl Tape

Figure15

78-8127-8892-1 Rev B 11

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

6.0 External Grounding (Optional)

6.1 Wrap the ground strap around the shield sleeve with the tails toward the cable jacket (Figure 16 ). Ensure that the

shield sleeve is over the tape, LC, or wire shield.

Ground Strap

Shield Sleeve

Figure16

6.2 Secure ground strap to the shield sleeve using a constant force spring (Fig ure 17).

Constant Force Spring

Figure17

6.3 Overwrap the spring with two layers of stretched vinyl tape (Figure 18).

Vinyl Tape

Figure18

12 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

6.4 Place one mastic sealing strip on the cable jacket under the solder blocks of the ground strap no farther than 1/2"

(13 mm) from the jacket edge (Figure 19).

1/2” max

(13 mm)

Mastic Strip

Figure19

6.5 Place another mastic strip over the solder blocks. Press the mastic strips around the solder blocks and onto the

cable jacket. If tails overlap at the solder blocks, place a piece of mastic between them (Figure 20).

1/2” max

(13 mm)

Mastic Strip

Figure20

78-8127-8892-1 Rev B 13

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

7.0 Install Jacket

Note: Jacketing is not optional.

7.1 Wrap a roll of slightly stretched Scotch

Rubber Mastic Tape 2228, 2" x 36" around cable jacket ends (tacky side

toward cable) (Figure 21). If grounding was applied, apply tape over mastic strips at solder block. Stretch and tear

off last 1 - 2" (25 - 50 mm) of mastic (Figure 22).

2" rubber mastic 2" rubber mastic

Figure21

Stretch and tear off last 1 - 2"

(25 - 50 mm) of rubber mastic

Figure22

7.2 Install the rejacketing tube by twisting the tube (not the liner) from side to side to start the movement. Then slide

and unroll the tube over the constant force springs and rubber mastic. (Figure 23). Repeat on other side.

Twist to break seal,

then slide tube

Liner

Figure23

14 78-8127-8892-1 Rev B

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

7.3 Remove the liners and discard.

Figure24

7.4 Connect optional grounding.

Note: In applications where the splice is regularly exposed to high levels of ultra-violet radiation (i.e. direct

sunlight), wrap two half-lapped layers of Scotch

Super 33+

™

Vinyl Electrical Tape or Scotch

Vinyl

Electrical Tape Super 88 over the rejacketing tube.

78-8127-8892-1 Rev B 15

™

Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000

Crimping Tool - Die Sets (number of crimps/end)

™

Connector

Number

Conductor

Size (kcmil)

Burndy Thomas & Betts Corp.

Square D Co.

Anderson Div.

Y34A

Y35, &39

Y45*, Y46*

Y1000** TBM 8 TBM 12 TBM 15

VC6-3**

VC6-FT**

VC8C**

10011 (Cu)

350

A31R (2) U31RT (2) — Red (3) — 71H (3) (2) —

20011 (Al/Cu)

350

— U31ART (2) (1) — 87H (3) 87H (3) (2) —

11011 (Cu)

350

A31R (2) U31RT (3) — Red (4) — 71H (4) (3) —

Cl-350 (Al/Cu)

350

— U31ART (2) — — 87H (2) 87H (2) (3) —

20012 (Al/Cu)

400

— U32ART (4) (1) — 94H (4) 94H (4) (2) (2)

10014 (Cu)

500

A34R (2) U34RT (2) — Brown (3) — 87H (3) (2) —

20014 (Al/Cu)

500

— U34ART (4) (1) — 106H (3) 106H (4) (2) (2)

11014 (Cu)

500

A34R (2) U34RT (3) — Brown (4) — 87H (4) (3) —

Cl-500 (Al/Cu)

500

— U34ART (3) — — — 106H (3) (3) —

20016 (Al/Cu)

600

— U36ART (4) (1) — — 115H (3) (3) (3)

10019 (Cu)

750

— U39RT (3) — — — 106H (3) — —

20019 (Al/Cu)

750

— U39ART (4) — — — 125H (5) (3) (3)

11019 (Cu)

750

— U39RT (5) — — — 106H (4) — —

Cl-750 (Al/Cu)

750

— S39ART (3) — — — 140H (3) (3) —

10024 (Cu)

1000

—

S44RT,

P44RT (4)

— — — 125H (3) — —

20024 (Al/Cu)

1000

—

S44ART,

P44ART (4)

— — — 140H (4) — —

11024 (Cu)

1000

—

S44RT,

P44RT (4)

— — — 125H (4) — —

*Y45 and Y46 accept all Y35 dies (“U Series”). For Y45, use PT6515 adapter. For Y46, use PUADP adapter.

**Anderson VC6-3, VC6-FT, VC8C and Burndy Y1000 require no die set.

3M, Super 33+, and Scotch are trademarks of 3M Company.

UniShield is a registered trademark of General Cable Technologies Corporation.

All other trademarks are the property of their respective owners.

Important Notice

All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable,

but the accuracy or completeness is not guaranteed.

Before using this product, you must evaluate it and determine if it is suitable for

your intended application.

You assume all risks and liability associated with such use.

Any statements related to the product which are not

contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless

expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture at the time of purchase.

3M MAKES NO OTHER WARRANTIES

INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the

3M product or refund the purchase price of the 3M product.

Except where prohibited by law, 3M will not be liable for any direct,

indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory

asserted.

Electrical Markets Division

6801 River Place Blvd.

Austin, TX 78726-9000

800.245.3573

Fax 800.245.0329

www.3M.com/electrical

Please Recycle. Printed in USA.

78-8127-8892-1 Rev B

3M Cold Shrink QS4 Integrated Splice QS4-35TS-QCI-350-750 Operating instructions

Brand: 3M

Model: Cold Shrink QS4 Integrated Splice QS4-35TS-QCI-350-750

Type: Operating instructions

This manual is also suitable for

Download PDF

report

3M Cold Shrink QS4 Integrated Splice QS4-35TS-QCI-350-750 Operating instructions

This manual is also suitable for

3M Cold Shrink QS4 Integrated Splice QS4-35TS-QCI-350-750 Operating instructions

Related papers

Other documents