GRAUPNER SWITCHING POWER SUPPLY 5-15V 0-15A Owner's manual

Page is loading ...

Order.-Nr. 6458 SWITCHING POWER SUPPLY 5 - 15V 0 - 15A

Order.-Nr. 6459 SWITCHING POWER SUPPLY 5 - 15V 0 - 20A

Wide Adjustable Output Area Constant Current

Introduction

Please be sure to read right through these operating instruction attentively before you

attempt to use your new switching power supply, as this will ensure that you can make full

use of all of its facilities. Take particular note of the warnings and safety notes. These

instructions should be kept in a safe place; if you ever dispose of the charger be sure to pass

them on to the new owner.

This power supply is small, lightweight, compact, provided with a current limiter, a

universal output for 4mm banana plugs and an automatic current regulator. At the same time,

it is suitable for giving power or testing your equipment. It’s also provided with a protection

circuitry to prevent any damages to the unity or your equipment in case of malfunctioning to

high-voltages. Fitted out with a cooling system that guarantees a constant full operatively to

the unit and prevents from overheating. This power supply is perfect to supply 12V chargers

and DC mini drills. This power supply can also be used as a Pb charger.

1. Specification:

 Input Voltage: 220~240V AC 50Hz

 Input Plug: #6458 EURO main plug, #6459 SCHUKO plug

 Output Power: #6458 200W, #6459 300W

 Output Connection: 4mm Banana Clamp

 Output Voltage: 5V~15V DC (adjustable)

 Output Current: #6458 0~15A (adjustable) #6459 0~20A (adjustable)

 Size: #6458 142×130×84mm, #6458 170×170×85mm

2. Features:

 Over power protection, short circuit protection

 Inner cooling system by fan

 Adjustable maximum power output

Pw =Vo×Io

Vo: output voltage (adjustable)

Io: output current in short circuit (adjustable)

 LED displaying output voltage and current

3. Operating Instructions:

1. Using as a common DC power supply: plug in, adjust the voltage knob to get your

needed value (5~15V). The voltage button “ ”will show the set voltage on screen.

Then turn the Amp knob to get your needed max current cut off point, Amp button “ ”

will show you the value.

2. Read thoroughly the following contents before using.

3. Disconnect the power supply from AC mains power before connecting device to the

power supply.

4. Connect the device to the power supply ensuring the correct polarity. Red is positive.

Black is negative and ensuring good contact.

5. Switch the power supply “OFF” with the switch on the front of the unit. Connect the

power supply input AC lead.

6. Switch the power supply “ON” with the switch on the front of the unit. The “power on”

led will illuminate. And the unit will commence supply of power to the device.

• Warnings:

• When the power supply is operating. Do not attempt to open the power supply casing. In

doing so will void warranty.

• Do ensure correct polarity when connecting device to the power supply. As damage to this

device may occur if in correct connections are made.

• Do not attempt use with device requiring greater current than Rated 40 amps.

• Do not allow to rain and to become wet.

• Only connect to AC mains outlet when in use at all other time disconnect the power

supply from AC mains outlet.

• Power supply may become warm during use or emit a slight buzzing sound. This is quit

norm and can be disregarded.

• Do place the power supply on a non flammable surface when in use.

• This power supply is for indoor use only.

3. Using as a charger (charging with constant voltage, constant current) :

Charging battery Suitable voltage area Constant current

12VLead-acid battery 13.8V~14.2V

6VLead-acid battery 6.9V~7.1V

Battery capacity

1h

Four-cell LiFe pack 14.0-14.4V

Battery capacity

1h

Three-cell Lipo pack

Three-cell LiFe pack

12.3V

10.6-10.8V

Two-cell LiPo pack

Two-cell LiFe pack

8.2V

7.0-7.2V

Battery capacity

1h

7Ah

e.g: 6VLead-acid battery: Constant current = = 1.4A

5

(1/5～1/10) ×

(1/2～2) ×

(1～4) ×

WARNINGS AND SAFETY NOTES

• This product isn‘t designed for use by children under the age of 14, it isn‘t a toy! This

appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety. Children should be supervised to ensure that they do not play with the

appliance.

• Protect the charger from dust, damp, rain, heat (e.g. direct sunshine) and vibration. It should

only be operated in dry indoor conditions.

• The case slots serve to cool the charger, and must not be covered or enclosed; set up the

charger with space round it, so that cooling air can circulate unhindered.

• The charger is designed to be powered by a 220~240V AC main socket only. It is not

permissible to modify the charger in any way. You must not connect AC power to the DC

input.

• The charger and the battery to be charged should be set up on a heat-resistant, non-

inflammable and non-conductive surface before use. Never place the charger directly on a

car seat, carpet or similar. Keep all inflammable and volatile materials well away from the

charging area. Provide good ventilation. Defective batteries can explode or burn!

• The charge output sockets and connecting leads must not be modified, and must not be

inter-connected in any way. There is a danger of short-circuit between the charge outputs

and the vehicle’s bodywork when the charger is connected to the car battery. The charge

leads and connecting leads must not be coiled up when the charger is in use. Avoid short-

circuiting the charge output or the model battery with the car bodywork. For this reason the

charger must never be placed directly on the vehicle’s bodywork.

• Never leave the charger running or connected to the car battery unsupervised.

• Only one battery may be connected at each output at any one time.

• The following types of battery must not be connected to the charger:

• Ni-Cd / Ni-MH batteries, lead-acid batteries with a nominal voltage of more than 12V

or less than 6V, Lithium-Ion / Li-Mn / Lithium-Polymer / LiFePO

4

(LiFe) batteries

with less than 2 cells and more than 3 cells (4 cells for LiFePO

4)

.

• Batteries which require a different charge method from CC/CV or lead-acid types.

• Faulty or damaged cells or batteries.

• Batteries consisting of parallel-wired cells, or cells of different types.

• Batteries consisting of old and new cells, or cells of different makes.

• Non-rechargeable batteries (dry cells). Caution: explosion hazard!

• Batteries which are not expressly stated by the manufacturer to be suitable for the

currents which this unit delivers during the charge process.

• Packs which are already fully charged or hot, or only partially discharged.

• Batteries or cells fitted with an integral charge circuit or charge termination circuit.

• Batteries installed in a device, or which are electrically connected to other components.

• To avoid short-circuits between the banana plugs fitted to the charge leads, please always

connect the charge leads to the charger first, and only then to the battery to be charged.

Reverse the sequence when disconnecting.

• As a basic rule always check that the charge quantity is approximately the same as you

expected after

the charger has indicated that the pack is fully charged. This is a simple

method of detecting a problem reliably and in good time, should the charge process be

terminated prematurely for any reason. The likelihood of premature termination varies

according to many factors, but is at its highest with deep-discharged packs, low cell counts

and particular cell types which are known to cause problems.

• We recommend that you carry out a series of test charges to satisfy yourself that the

automatic termination circuit is working perfectly. This applies in particular when you are

charging packs consisting of a small number of cells. If the cells feature has a poorly

defined voltage peak, the charger may fail to detect the fully charged state.

• Before charging please check: have you selected the appropriate charge output for the

battery? Are all connections firm, or is there an intermittent contact at any point in the

circuit? Please bear in mind that it can be dangerous to fast-charge batteries. For example, if

there is a brief interruption due to an intermittent contact, the result is inevitably a

malfunction such as a restart of the charge process, which would result in the pack being

massively overcharged.

• Be careful! A battery could explode or burn, if the charger does have a fault or if the

user does choose the wrong charging output and parameters.

4. Operation:

1. Connect the charger to an easily accessible mains power socket (220-240V AC,

50Hz).The red LED display will be on to confirm that the charger is ready for use.

Adjust the max. charge current and charge voltage like shown in the table.

Doing not so or adjusting the wrong voltage or current can cause explosion and fire.

2. Make absolutely sure that the polarity of the battery and the polarity of the charging

cable match.

- RED to positive pole (+)

- BLACK to negative pole

The charge current can be displayed in the LED display to indicate that charging is in

progress.

4. If the charge current is lower as 0.1 - 0.2A, the battery is fully charged. Disconnect the

battery from the charge lead, and disconnect the charger from the mains socket.

5. In case of charging LiFe or LiPo batteries, you must use the LiPo-Balancer 5 plus

#3064 or LiPo-Balancer 6 plus #3065 for safety reasons. The maximum charge current

must be limited to max. 10 A. Use a LiPo safety case #8370 or #8371.

5. Safety notes:

¾ Make sure to follow the correct polarity connecting the battery charger. In case of

wrong connection you could cause severe damages to the battery charger

connected.

¾ Protect the charger from dust, damp, rain, heat (e.g. direct sunshine)and vibration. It

should only be operated in dry, indoor conditions.

¾ The case surface serves to cool the charger and must not be covered or enclosed;

cooling air must be able to circulate unhindered.

¾ Do not leave the charger running unsupervised.

¾ Power supply may become warm during use or emit a slight buzzing sound, this is

normal and can be disregarded.

¾ Do not attempt to open the casing, as there are no user serviceable parts inside, and

this may void the warranty.

¾ For indoor use only.

¾ The following types of battery must not be connected to the charger:

- Faulty, damaged or hot batteries

- NiMH or NiCd batteries

- Non-rechargeable batteries (dry cells)

6. Caution: explosion hazard!

- Batteries which are not expressly stated by the manufacture to be suitable for the

currents which the unit produces during the charge process.

- Batteries which are already fully charged or hot, or only partially discharged.

- Batteries fitted with an integral charge circuit or charge termination circuit.

Graupner GmbH & Co.KG, Henriettenstr. 94-96, 73230 Kirchheim/Teck, Germany

Page is loading ...

EG-Konformitätserklärung

Für das folgend bezeichnete Erzeugnis

Best.-Nr. 6461

wird hiermit bestätigt, dass es den wesentlichen Schutzanforderungen entspricht, die in der Richtlinie des Rates

zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über die elektromagnetische Verträglichkeit

(89/336/EWG) und (73/23/EWG) über die elektrische Sicherheit festgelegt sind.

Zur Beurteilung des Erzeugnisses hinsichtlich elektromagnetischer Verträglichkeit wurden folgende Normen

herangezogen:

EN 61558-1 Prüfung der elektrischen Sicherheit

EN 61558-2-17

Diese Erklärung wird verantwortlich für den Hersteller/Importeur

Graupner GmbH & Co. KG

Henriettenstr. 94-96

73230 Kirchheim/Teck

abgegeben durch den Geschäftsführer

73230 Kirchheim/Teck, den 21.10.2008

Unterschrift

---------------------------------------------------------------------------------------------------------------------------

Declaration of Conformity

We hereby certify that the product designated in the following:

Order Nr: 6461

complies with the essential safety requirements as laid down in the Outlines of the Council for the Adaptation of

Legal Regulations for Electro-Magnetic Compatibility (89/336/EWG) and (73/23/EWG) LVD in its member states.

In assessing the electro-magnetic compatibility of this product the following norms have been applied:

EN 61558-1 LVD

EN 61558-2-17 LVD

This declaration of responsibility has been issued in accordance with the producer/importer

Graupner GmbH & Co. KG

Henriettenstr. 94-96

73230 Kirchheim/Teck

by Managing Director

73230 Kirchheim/Teck signed on 21.10.2008

Signature

Hinweise zum Umweltschutz

Das Symbol auf dem Produkt, der Gebrauchsanleitung oder der Verpackung weist darauf hin, dass dieses Produkt bzw. elektronische Teile davon

am Ende seiner Lebensdauer nicht über den normalen Haushaltsabfall entsorgt werden dürfen. Es muss an einem Sammelpunkt

für das Recycling von elektrischen und elektronischen Geräten abgegeben werden.

Die Werkstoffe sind gemäß ihrer Kennzeichnung wieder verwertbar. Mit der Wiederverwendung, der stofflichen Verwertung oder

anderen Formen der Verwertung von Altgeräten leisten Sie einen wichtigen Beitrag zum Umweltschutz.

Batterien und Akkus müssen aus dem Gerät entfernt werden und bei einer entsprechenden Sammelstelle getrennt entsorgt

werden.

Bei RC-Modellen müssen Elektronikteile, wie z.B. Servos, Empfänger oder Fahrtenregler aus dem Produkt ausgebaut und getrennt bei einer

entsprechenden Sammelstelle als Elektro-Schrott entsorgt werden.

Bitte erkundigen Sie sich bei der Gemeindeverwaltung die zuständige Entsorgungsstelle.

Environnemental Protection Notes

When this product comes to the end of its useful life, you must not dispose of it in the ordinary domestic waste. The correct

method of disposal is to take it to your local collection point for recycling electrical and electronic equipment. The symbol shown

here, which may be found on the product itself, in the operating instructions or on the packaging, indicates that this is the case.

Individual markings indicate which materials can be recycled and re-used. You can make an important contribution to the

protection of our common environment by re-using the product, recycling the basic materials or recycling redundant equipment in

other ways.

Remove batteries from your device and dispose of them at your local collection point for batteries.

In case of R/C models, you have to remove electronic parts like servos, receiver, or speed controller from the product in question, and these parts

must be disposed of with a corresponding collection point for electrical scrap.

If you don’t know the location of your nearest disposal centre, please enquire at your local council office.

Indications quant à la protection de

l’environnement

Ce produit à la fin de sa durée de vie ne doit pas être mis à la poubelle, mais être remis à une collecte pour le recycle ment

d'appareils électriques et électroniques. Le symbole inscrit sur le produit, dans la notice d'instructions et sur son emballage

l'indique.

Les matériaux selon leurs reconnaissances sont réutilisables. Avec le recyclage de matériaux et autres formes d'appareils, vous

contribuez à la protection de l'environnement.

Les batteries et accus doivent être retirés de l'appareil et doivent être remis à un dépôt homologué pour ce type de produits.

Pour les modèles radiocommandés, les pièces électroniques, comme par exemple les servos, récepteur ou variateur de vitesse, doivent être

démontés et retirés du produit et être remis à une collecte spécialisée pour produits électroniques.

Veuillez s.v.p. demander auprès de votre mairie l'adresse exacte du point de récupération le plus proche de chez vous.

GRAUPNER SWITCHING POWER SUPPLY 5-15V 0-15A Owner's manual

GRAUPNER SWITCHING POWER SUPPLY 5-15V 0-15A Owner's manual

in other languages

Related papers

Other documents