PRECISION DIGITAL PD8-6310 User manual

ProtEX-MAX PD8-6310 Explosion-Proof

Pulse Input Batch Controller Instruction Manual

PRECISION DIGITAL CORPORATION

233 South Street • Hopkinton MA 01748 USA

Tel (800) 343-1001 • Fax (508) 655-8990

www.predig.com

Batch Controller

• Pulse, Open Collector, NPN, PNP, TTL, Switch Contact,

Sine Wave (Coil), Square Wave Inputs

• 5, 10, or 24 V Flowmeter Power Supply

• K-Factor, Internal Scaling, or External Calibration

• Start, Batch, Pause, & Stop with Front Panel Buttons

• Display Batch Total + Rate, Grand Total, Batch Count or Preset

• Single or Multi-Stage Batching with up to 4 Relays

• Automatic Overflow Protection

• Manual Control or Automatic Batching

• Modern, Sleek and Practical Enclosure

• Display Mountable at 0°, 90°, 180°, & 270° Degrees

• Explosion-Proof, IP68, NEMA 4X Enclosure

• SafeTouch

®

Through-Glass Button Programming

• Flanges for Wall or Pipe Mounting

• Superluminous Sunlight Readable Display

• Free USB Programming Software & Cable

USB Install

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

2

Disclaimer

The information contained in this document is subject to change without notice. Precision

Digital makes no representations or warranties with respect to the contents hereof; and

specifically disclaims any implied warranties of merchantability or fitness for a particular

purpose.

CAUTION: Read complete

instructions prior to installation

and operation of the controller.

WARNING: Risk of

electric shock or

personal injury.

Warning!

• This product is not recommended for life support applications or applica-

tions where malfunctioning could result in personal injury or property

loss. Anyone using this product for such applications does so at his/her

own risk. Precision Digital Corporation shall not be held liable for dam-

ages resulting from such improper use.

• Failure to follow installation guidelines could result in death or serious in-

jury. Make sure only qualified personnel perform the installation.

• Never remove the instrument cover in explosive environments when the

circuit is live.

• Cover must be fully engaged to meet flameproof/explosion-proof require-

ments.

• Information in this manual supersedes all enclosure, compliance, and

agency approval information included in additional product manuals in-

cluded with this product.

Limited Warranty

Precision Digital Corporation warrants this product against defects in material or

workmanship for the specified period under “Specifications” from the date of shipment from

the factory. Precision Digital’s liability under this limited warranty shall not exceed the

purchase value, repair, or replacement of the defective unit.

Registered Trademarks

MeterView

®

Pro is a registered trademark of Precision Digital Corporation. Modbus

®

is a

Registered Trademark of Schneider Automation Inc. All other trademarks mentioned in this

document are the property of their respective owners.

www.predig.com

!

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual 
   
 
 
3 
 
Table of Contents 
Table of Contents ----------------------------------------- 3 
Table of Figures ------------------------------------------- 4 
Introduction ------------------------------------------------- 4 
Ordering Information ------------------------------------ 5 
Specifications ---------------------------------------------- 5 
General ------------------------------------------------------------ 5 
Pulse Input ------------------------------------------------------- 6 
Batch Controller Rate/Totalizer Display --------------- 6 
Relays ------------------------------------------------------------- 7 
Isolated 4-20 mA Transmitter Output ------------------- 7 
Serial Communications -------------------------------------- 8 
MeterView Pro -------------------------------------------------- 8 
Product Ratings and Approvals; ------------------------- 9 
Compliance Information ------------------------------ 10 
Safety ------------------------------------------------------------ 10 
Electromagnetic Compatibility -------------------------- 10 
Safety Information -------------------------------------- 11 
Installation ------------------------------------------------ 11 
Unpacking ------------------------------------------------------ 11 
Pre-Installed Conduit/Stopping Plug ------------------ 12 
Mounting ------------------------------------------------------- 12 
Cover Jam Screw -------------------------------------------- 12 
Transmitter Supply Voltage Selection (P+, P-) ---- 12 
Connections --------------------------------------------------- 13 
Required & Factory Wired Connection --------------- 13 
Connectors Labeling -------------------------------------- 14 
Power Connections --------------------------------------- 14 
Pulse Signal Connections ------------------------------- 15 
Serial Communication Connections ------------------ 15 
Three Wire Connections ----------------------------- 16 
Using PROVU Serial Adapters --------------------------- 17 
Relay Connections ---------------------------------------- 18 
Switching Inductive Loads ------------------------------- 18 
F4 Digital Input Connections ---------------------------- 19 
4-20 mA Output Connections --------------------------- 19 
Analog Output Transmitter Power Supply ----------- 19 
Interlock Relay Feature ---------------------------------- 19 
Digital I/O Connections ----------------------------------- 20 
External Switch Contacts -------------------------------- 20 
Basic Operation and Programming --------------- 21 
SafeTouch
®
 Buttons ---------------------------------------- 21 
Front Buttons and Status LED Indicators ----------- 22 
Controller Operation ---------------------------------------- 23 
Batch Control Operation Example --------------------- 24 
MeterView
®
 Pro Software --------------------------------- 26 
MeterView Pro Installation ------------------------------ 26 
Display Functions and Messages ---------------------- 27 
Setting Numeric Values ----------------------------------- 29 
Setting Up the Batch Controller (setup) ------------- 30 
Scaling and Calibration ---------------------------------- 31 
Setting the Input Signal (Input) ------------------------ 31 
Setting the Totalizer and Batching Features (total)
 ----------------------------------------------------------------- 31 
Setting the Input Units or Custom Tags (units)--- 31 
Setting the Decimal Point (dEc pt) ------------------- 32 
Programming the Batch Controller (prog) ----------- 32 
Input Calibration Method (InCAL) ------------------ 33 
K-Factor Calibration (Factor) ---------------------- 33 
Scaling the Controller (SCALE) ---------------------- 34 
Time Base, Total Conversion Factor & Total 
Reset ------------------------------------------------ 34 
Batch Start Mode (mode) ------------------------------ 35 
Calibrating the Controller with External Source 
(Cal) ------------------------------------------------- 35 
Setting the Display Parameter & Intensity (dsplay)
 ----------------------------------------------------------------- 36 
Setting the Relay Operation (relay) ------------------ 37 
Relay Assignment (Assign) ---------------------------- 38 
Setting the Relay Action --------------------------------- 38 
Setting Batch Control Relays --------------------------- 38 
Programming Alarm Set and Reset Points --------- 39 
Setting Fail-Safe Operation ----------------------------- 39 
Programming Time Delay ------------------------------- 39 
Relay Operation Details ----------------------------------- 40 
Overview ----------------------------------------------------- 40 
Relays Initialization --------------------------------------- 40 
Fail-Safe Operation --------------------------------------- 40 
Front Panel LEDs ----------------------------------------- 40 
Automatic Reset (Auto) ---------------------------------- 41 
Pump Alternation Control -------------------------------- 41 
Setting Up the Interlock Relay (Force On) Feature 41 
Sample Relay Operation -------------------------------- 42 
Relay and Alarm Operation Diagrams ---------------- 42 
High Alarm Operation (Set > Reset) ------------------ 42 
Low Alarm Operation (Set < Reset) ------------------ 42 
High Alarm with Fail-Safe Operation (Set > Reset)
 ----------------------------------------------------------------- 42 
Low Alarm with Fail-Safe Operation (Set < Reset) 42 
Rate Relay Sampling Operation ----------------------- 43 
Total Relay Sampling Operation ----------------------- 43 
Time Delay Operation ------------------------------------ 44 
Scaling the 4-20 mA Analog Output (Aout) --------- 44 
Reset Menu (reset) ----------------------------------------- 45 
Control Menu (Contrl) ------------------------------------- 45 
Setting Up the Password (pass) ------------------------ 45 
Protecting or Locking the Controller ------------------ 45 
Grand Total Reset Password & Non-Resettable 
Total ---------------------------------------------------------- 46 
Making Changes to a Password Protected 
Controller ---------------------------------------------------- 46 
Disabling Password Protection ------------------------ 46 
Advanced Operation and Programming --------- 47 
Advanced Features Menu & Display Messages --- 47 
Function Keys Operation -------------------------------- 49 
F4 Operation ------------------------------------------------ 49 
Multi-Point Calibration & Scaling ---------------------- 49 
Maximum/Minimum Readings -------------------------- 49 
Noise Filter (filter) ----------------------------------------- 50 
Noise Filter Bypass (bypass) --------------------------- 50 
Rounding Feature (round) ------------------------------ 50 
Modbus RTU Serial Communications (serial) --- 50 
Serial Communications Overview --------------------- 51 
Select Menu (SElEct) ------------------------------------ 52 
Signal Conditioning Selection (Functn) ---------- 52 
Low-Flow Cutoff (CutofF) --------------------------- 52 

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual 
   
 
 
 
4 
 
Total and Grand Total Count Direction (Count) 52 
Analog Output Programming (AoutPr) ----------- 53 
Programmable Function Keys User Menu (user) - 53 
Troubleshooting ----------------------------------------- 55 
Diagnostics Menu (diag) -------------------------------- 55 
Determining Software Version ------------------------- 55 
Reset Controller to Factory Defaults ------------------ 55 
Factory Defaults & User Settings ---------------------- 56 
Troubleshooting Tips -------------------------------------- 57 
Service ------------------------------------------------------ 59 
Mounting Dimensions --------------------------------- 60 
EU Declaration of Conformity ----------------------- 61 
Table of Figures 
Figure 1: Transmitter Supply Voltage Selection ....... 12 
Figure 2: Integrated ProVu Required Connections .. 13 
Figure 3: Connector Labeling for Fully Loaded PD8-
6310 ...................................................................... 14 
Figure 4: Power Connections..................................... 14 
Figure 5: Flowmeter Powered by Internal Power 
Supply .................................................................. 15 
Figure 6: Flowmeter Powered by External Supply ... 15 
Figure 7: Self-Powered Magnetic Pickup Coil 
Flowmeter ............................................................ 15 
Figure 8: NPN open Collector Input ........................... 15 
Figure 9: PNP Sensor Powered by Internal Supply .. 15 
Figure 10: Switch Input Connections ........................ 15 
Figure 11: ProtEX-MAX Connections to a Serial 
Converter ............................................................. 15 
Figure 12. Three-Wire RS485 Connection .................. 16 
Figure 13: RS-485 Wiring ............................................ 16 
Figure 14: RS-485 Two-Wire Multi-Drop Wiring ........ 17 
Figure 15: Relay Connections .................................... 18 
Figure 16: AC and DC Loads Protection .................... 18 
Figure 17: Low Voltage DC Loads Protection ........... 18 
Figure 18: F4 Digital Input Connections .................... 19 
Figure 19: 4-20 mA Output Connections ................... 19 
Figure 20: Interlock Connection ................................. 19 
Figure 21: Digital I/O Connections ............................. 20 
Figure 22: General Four-Wire Network Connection .. 51 
Figure 23: General Two-Wire Network Connection... 51 
Figure 24: Enclosure Dimensions – Front View ........ 60 
Figure 25: Enclosure Dimensions – Side Cross 
Section View ......................................................... 60 
 
Introduction 
The ProtEX-MAX PD8-6310 offers all the functionality of the ProVu PD6310 as a fully FM, CSA, 
ATEX, and IECEx approved explosion-proof product. It is a pulse input (NPN, PNP, TTL, switch 
contact, sine wave, etc.) digital batch controller specifically designed for single and multi-stage 
batching applications. It provides excellent but simple batch control capabilities with features such 
as preclose relays and automatic overrun correction for more accurate batches and convenient 
SafeTouch® through-glass buttons for simple operation and menu navigation without having to 
remove the cover. The preclose deactivates a specific relay before the batch is finished in order 
to allow slower fill rates and increased accuracy. Automatic overrun correction keeps the batch 
size accurate over time and with system wear. The PD8-6310 includes a 24 VDC power supply 
to drive the flowmeter and can be equipped with up to four internal relays and a 4-20 mA analog 
output. 
   

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

5

Ordering Information

SunBright Display Models

85-265 VAC Model

12-24 VDC Model

Options Installed

PD8-6310-6H7

PD8-6310-7H7

4 relays & 4-20 mA output

WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Accessories

Model

Description

PDA1232

RS-232 serial adapter

PDA1485

RS-485 serial adapter

PDA7485-I

RS-232 to RS-422/485 isolated converter

PDA8232-N

USB to RS-232 non-isolated converter

PDA8485-I

USB to RS-422/485 isolated converter

PDX6901

Suppressor (snubber): 0.01 µF/470 , 250 VAC

Specifications

Except where noted all specifications apply to operation at +25°C.

General

Display

Line 1: 0.6" (15 mm) high, red LEDs

Line 2: 0.46" (12 mm) high, red LEDs

6 digits: each (-99999 to 999999), with lead

zero blanking.

Default

Display

Assignment

Display line 1 shows batch total. Display line

2 shows rate with alternating units, and can

be switched to show grand total, batch

count, or preset with the STOP key.

Custom

Display

Assignment

The Upper and Lower displays may be

assigned to rate, total, grand total, batch

count, preset, set points, units (lower display

only), alternating R & T, R & GT, preset &

rate, max & min, or a Modbus display

register. Any rate/total/grand total display

may be programmed to alternate with a

custom unit or tag.

Alternating

Display

Displays alternate every 10 seconds when

display is selected or the batch is paused.

Display

Intensity

Eight user selectable intensity levels

Display

Update Rate

5/second (200 ms)

Overrange

Display flashes 999999

Underrange

Display flashes -99999

Front Panel

NEMA 4X, IP65

Programming

Methods

Four front panel buttons, digital inputs, or

PC and MeterView Pro software.

Recalibration

All ranges are calibrated at the factory.

Recalibration is recommended at least every

12 months.

Max/Min

Display

Max/min readings reached by the process

are stored until reset by the user or until

power to the controller is cycled.

Password

Three programmable passwords restrict

modification of programmed settings and

two prevent resetting the totals.

Pass 1: Allows use of function keys and

digital inputs

Pass 2: Allows use of function keys, digital

inputs and editing set/reset points

Pass 3: Restricts all programming, function

keys, and digital inputs.

Total Password: Prevents resetting the total

manually

Gtotal Password: Prevents resetting the

grand total manually

Non-Volatile

Memory

All programmed settings are stored in non-

volatile memory for a minimum of ten years

if power is lost.

Power

Options

85-265 VAC 50/60 Hz, 90-265 VDC, 20 W

max or 12-24 VDC  10%, 15 W max

Powered over USB for configuration only

Fuse

Required external fuse: UL Recognized, 5 A

max, slow blow; up to 6 controllers may

share one 5 A fuse

Isolated

Transmitter

Power Supply

Terminals P+ & P-: 24 VDC  10%. Selectable

for 24, 10, or 5VDC supply (internal jumper J4).

All models transmitter supply rated @ 25mA

max.

Normal Mode

Rejection

Greater than 60 dB at 50/60 Hz

Isolation

4 kV input/output-to-power line

500 V input-to-output or output-to-P+ supply

Overvoltage

Category

Installation Overvoltage Category II:

Local level with smaller transient

overvoltages than Installation Overvoltage

Category III.

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

6

Environmental

T6 Class operating temperature range Ta =

-40 to 60°C

T5 Class operating temperature range Ta =

-40 to 65°C

Max Power

Dissipation

Maximum power dissipation limited to 15.1

W.

Connections

Screw terminals accept 12 to 22 AWG wire

Enclosure

Explosion-proof die cast aluminum with

glass window, corrosion resistant epoxy

coating, color: blue.

NEMA 4X, 7, & 9, IP68.

Default conduit connections: Four ¾" NPT

threaded conduit openings and two ¾" NPT

metal conduit plugs with 12 mm hex key

fitting installed. Additional conduit opening

configurations may be available; verify

quantity and sizes on specific device

labeling during installation.

Mounting

Four slotted flanges for wall mounting or

NPS 1½" to 2½" or DN 40 to 65 mm pipe

mounting. See Mounting Dimensions on

page 60.

Tightening

Torque

Screw terminal connectors: 5 lb-in (0.56 Nm)

Overall

Dimensions

6.42" x 7.97" x 8.47" (W x H x D)

(163 mm x 202 mm x 215 mm)

Weight

16.0 lbs (7.26 kg)

Warranty

3 years parts & labor

Pulse Input

Inputs

Field selectable: Pulse or square wave 0-5

V, 0-12 V, or 0-24 V @ 30 kHz; TTL; open

collector 4.7 k pull-up to 5 V @ 30 kHz;

NPN or PNP transistor, switch contact 4.7

k pull-up to 5 V @ 40 Hz; Modbus PV

(Slave)

Low Voltage

Mag Pickup

(Isolated)

Sensitivity: 40 mVp-p to 8Vp-p

Minimum

Input

Frequency

0.001 Hz

Minimum frequency is dependent on high

gate setting.

Maximum

Input

Frequency

30,000 Hz (10,000 for low voltage mag

pickup)

Input

Impedance

Pulse input: Greater than 300 k @ 1 kHz.

Open collector/switch input: 4.7 k pull-up

to 5 V.

Accuracy

±0.03% of calibrated span ±1 count

Temperature

Drift

Rate display is not affected by changes in

temperature.

Multi-Point

Linearization

2 to 32 points

Low-Flow

Cutoff

0-999999 (0 disables cutoff function)

Decimal Point

Up to five decimal places or none:

d.ddddd, d.dddd, d.ddd, d.dd, d.d, or

dddddd

Calibration

May be calibrated using K-factor, internal

calibration, or by applying an external

calibration signal.

K-Factor

Field programmable K-factor converts input

pulses to rate in engineering units. May be

programmed from 0.00001 to 999,999

pulses/unit.

Calibration

Range

Input 1 signal may be set anywhere in the

range of the controller; input 2 signal may be

set anywhere above or below input 1 setting.

Minimum input span between any two inputs

is 10 Hz.

An error message will appear if the input 1

and input 2 signals are too close together.

Filter

Programmable contact de-bounce filter: 40

to 999 Hz maximum input frequency allowed

with low speed filter.

Time Base

Second, minute, hour, or day

Gate

Low gate: 0.1-99.9 seconds

High gate: 2.0-999.9 seconds

F4 Digital

Input

Contacts

3.3 VDC on contact. Connect normally open

contacts across F4 to COM.

F4 Digital

Input

Logic Levels

Logic High: 3 to 5 VDC

Logic Low: 0 to 1.25 VDC

Batch Controller Rate/Totalizer Display

Rate Display

Indication

-99999 to 999999, lead zero blanking. “R”

LED illuminates while displaying rate.

Batch Total &

Grand Total

Display

0 to 999,999; automatic lead zero blanking.

“T” LED is illuminated while displaying batch

total. “GT” LEDs are illuminated while

displaying grand total. Up to 999,999 for

batch total/preset. Up to 999,999,999 with

grand total-overflow feature. “oF” is displayed

to the left of grand total overflow and ▲ LED

is illuminated.

Batch Total

Decimal Point

Up to five decimal places or none:

d.ddddd, d.dddd, d.ddd, d.dd, d.d, or

dddddd

Total decimal point is independent of rate

decimal point.

Totalizer

Calculates total based on rate and field

programmable multiplier to display total in

engineering units. Time base must be

selected according to the time units in which

the rate is displayed.

Grand

Totalizer

Rollover

Grand totalizer rolls over when display

exceeds 999,999,999. Relay status reflects

display.

Grand Total

Alarms

Up to seven, user selectable under setup

menu. Any set point can be assigned to

grand total and may be programmed

anywhere in the range of the controller for

grand total alarm indication. Relay 1 should

always be assigned to batch.

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

7

Programmabl

e Delay on

Release

0.1 and 999.9 seconds; applied to the first

relay assigned

to total or grand total.

If the controller is programmed to reset total

to zero automatically when the preset is

reached, then a delay will occur before the

total is reset.

Grand Total

Reset

Via front panel button, external contact

closure on digital inputs, automatically via

user selectable preset value and time delay,

or through serial communications.

Grand Total

Reset

Password

Grand total passwords may be entered to

prevent resetting the grand total from the

front panel.

Non-

Resettable

Grand Total

The grand total can be programmed as a

non-resettable total by entering the

password “050873”.

Caution!

Once the Grand Total has been

programmed as “non-resettable”

the feature cannot be disabled.

Relays

Rating

4 SPDT (Form C) internal and/or 4 SPST

(Form A) external; rated 3 A @ 30 VDC and

125/250 VAC resistive load; 1/14 HP (≈ 50

W) @ 125/250 VAC for inductive loads

Noise

Suppression

Noise suppression is recommended for each

relay contact switching inductive loads; see

page 18 for details.

Relay

Assignment

Relays may be assigned to batch control

total, sampling, rate, or grand total alarms.

Preclose

0-100% of batch size, individually user

programmable for each additional batch

control relay beyond the first.

Alarm

Deadband

0-100% of span, user programmable

High or Low

Alarm

User may program any alarm for high or low

trip point.

Unused alarm LEDs and relays may be

disabled (turn off).

Fail-Safe

Operation

Programmable and independent for each

relay.

Note: Relay coil is energized in non-alarm

condition. In case of power failure,

relay will go to alarm state.

Relay

Operation

Batch control

Automatic (non-latching)

1

Sampling

Off (disable unused relays and enable

Interlock feature)

Manual on/off control mode

Secondary Functions

2

Pump alternation control (2 to 4 relays)

Latching (requires manual acknowledge)

Relay Reset

User selectable via front panel buttons,

digital inputs, or PC

1. Automatic reset only (non-latching),

when the input passes the reset point

or total is reset to zero.

2. Automatic + manual reset at any time

(non-latching)

3. Manual reset only, at any time

(latching)

4. Manual reset only after alarm condition

has cleared (L)

Note: Digital inputs may be assigned to

acknowledge relays programmed for manual

reset. It is not recommended to change the

functions of front panel buttons to manual

reset.

Alarm Time

Delay

0 to 999.9 seconds, on & off relay time

delays

Programmable and independent for each

relay.

Alarm Auto

Initialization

When power is applied to the controller,

relays will reflect the state of the input to the

controller.

1

1. Alarms are active only when the batch is running.

2. These functions are not functional when the unit is being

used as a batch controller with total set to yes.

Isolated 4-20 mA Transmitter Output

Output

Source

Rate/process, total, grand total, max, min,

set points 1-4, Modbus register, or manual

control mode

Scaling

Range

1.000 to 23.000 mA for any display range.

Calibration

Factory calibrated: 4.000 to 20.000 = 4-20

mA output

Analog Out

Programming

23.000 mA maximum for all parameters:

Overrange, underrange, max, min, and

break

Accuracy

± 0.1% FS ± 0.004 mA

Temperature

Drift

0.4 µA/C max from 0 to 65C ambient,

0.8 µA/C max from -40 to 0C ambient

Note: Analog output drift is separate from input

drift.

Isolated

Transmitter

Power Supply

Terminals I+ & R: 24 VDC  10%. May be

used to power the 4-20 mA output or other

devices. Refer to Figure 3 on page 14 and

Figure 19 on page 19. All models @ 25mA

max.

External

Loop Power

Supply

35 VDC maximum

Output Loop

Resistance

Power supply

24 VDC

35 VDC

(external)

Minimum

10 

100 

Maximum

700 

1200 

!

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

8

Serial Communications

Compatibility

EIA-485

Connectors

Removable screw terminal connector

Max Distance

3,937' (1,200 m) max

Status

Indication

Separate LEDs for Power (P), Transmit

(TX), and Receive (RX)

Slave Id

1 – 247 (Controller address)

Baud Rate

300 - 19,200 bps

Transmit

Time Delay

Programmable between 0 and 199 ms

Data

8 bit (1 start bit, 1 or 2 stop bits)

Parity

Even, Odd, or None with 1 or 2 stop bits

Byte-To-Byte

Timeout

0.01 – 2.54 second

Turn Around

Delay

Less than 2 ms (fixed)

Note: Refer to the PROVU

®

Modbus Register Tables located

at www.predig.com for details.

Digital Inputs & Outputs

Channels

4 digital inputs & 4 digital outputs

Digital Input

Logic High

3 to 5 VDC

Digital Input

Logic Low

0 to 1.25 VDC

Digital Output

Logic High

3.1 to 3.3 VDC

Digital Output

Logic Low

0 to 0.4 VDC

Source

Current

10 mA maximum output current

Sink

Current

1.5 mA minimum input current

+5 V

Terminal

To be used as pull-up for digital inputs

only.

Connect normally open pushbuttons

across +5 V & DI 1-4.

WARNING

DO NOT use +5 V termi-

nal (pin 1) to power exter-

nal devices.

Function

Assignment

The on-board digital inputs (1-4) are

designed to mimic the behavior of the

front panel buttons (Menu, F1, F2, &

F3).

If you wish to change their behavior, re-

assign F1-F3 to the desired function,

then change the corresponding digital

input to match.

MeterView Pro

System Require-

ments

Microsoft

®

Windows

®

XP/Vista/7/8/10

Communications

USB 2.0 (Standard USB A to Micro USB

B)

Configuration

Configure device settings one at a time

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

9

Product Ratings and Approvals;

FM

Enclosure: Type 4X; IP66

Class I, Division 1, Groups B, C, D

Class II, Division 1, Groups E, F, G

Class III, Division 1, T5/T6

Class I, Zone 1, AEx d, IIC Gb T5/T6

Zone 21, AEx tb IIIC T90°C; Ta -40°C to +65°C

T6 Ta = -40°C to +60°C; T5 Ta = -40°C to +65°C

Certificate Number: 3047283

CSA

Class I, Division 1, Groups B, C, D

Class II, Division 1, Groups E, F, G

Class III, Division 1

Class I Zone 1 Ex d IIC

Zone 21 Ex tb IIIC T90°C

-40°C < Tamb. < +60° C; Temperature Code T6

-40°C < Tamb. < +65° C; Temperature Code T5

Enclosure Type 4X & IP66

Certificate Number: 2531731

ATEX

II 2 G D

Ex d IIC T* Gb

Ex tb IIIC T90°C Db IP68

Ta = -40°C to +*°C

*T6 = -40°C to +60°C

*T5 = -40°C to +65°C

Certificate number: Sira 12ATEX1182

IECEx

Ex d IIC T* Gb

Ex tb IIIC T90°C Db IP68

Ta = -40°C to +*°C

*T6 = -40°C to +60°C

*T5 = -40°C to +65°C

Certificate Number: IECEx SIR 12.0073

Special Conditions for Safe Use:

Use suitably certified and dimensioned cable entry device and/or plug. The equipment shall be

installed such that the supply cable is protected from mechanical damage. The cable shall not

be subjected to tension or torque. If the cable is to be terminated within an explosive atmos-

phere, then appropriate protection of the free end of the cable shall be provided. Cable must be

suitable for 90°C.

Year of Construction

This information is contained within the serial number with the first four digits representing the

year and month in the YYMM format.

For European Community: The ProtEX-MAX must be installed in accordance with the ATEX

directive 94/9/EC, and the product certificate Sira 12ATEX1182.

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

10

Compliance Information

Safety

UL & c-UL Listed

USA & Canada

UL 508 Industrial Control Equipment

UL File Number

E160849

Front Panel

UL Type 4X, NEMA 4X, IP65; panel gasket provided

Low Voltage

Directive

EN 61010-1:2010

Safety requirements for measurement, control, and laboratory use

Electromagnetic Compatibility

Emissions

EN 55022:2010

Class A ITE emissions requirements

Radiated

Emissions

Class A

AC Mains

Conducted

Emissions

Class A

Immunity

EN 61326-1:2013

Measurement, control, and laboratory equipment

EN 61000-6-2:2005

EMC heavy industrial generic immunity standard

RFI - Amplitude

Modulated

80 -1000 MHz 10 V/m 80% AM (1 kHz)

1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)

2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)

Electrical Fast

Transients

±2kV AC mains, ±1kV other

Electrostatic

Discharge

±4kV contact, ±8kV air

RFI - Conducted

10V, 0.15-80 MHz, 1kHz 80% AM

AC Surge

±2kV Common, ±1kV Differential

Surge

1KV (CM)

Power-Frequency

Magnetic Field

30 A/m 70%V for 0.5 period

Voltage Dips

40%V for 5 & 50 periods

70%V for 25 periods

Voltage

Interruptions

<5%V for 250 periods

Note:

Testing was conducted on PD6200 and PD6300 series meters installed through the covers of

grounded metal enclosures with cable shields grounded at the point of entry representing installations

designed to optimize EMC performance. All hardware is identical to the PD8-6310 controllers.

Declaration of Conformity available at www.predig.com

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

11

Safety Information

WARNINGS

• Read complete instructions prior to installation and operation of the instrument.

• Installation and service should be performed only by trained service personnel. Service

requiring replacement of internal sub-components must be performed at the factory.

• Disconnect from supply before opening enclosure. Keep cover tight while circuits are alive.

Conduit seals must be installed within 18" (450mm) of the enclosure or within 2" (50mm) for

Zone installations.

• Verify that the operating atmosphere of the instrument is consistent with the appropriate

hazardous locations certifications.

• If the instrument is installed in a high voltage environment and a fault or installation error

occurs, high voltage may be present on any lead

• Read all product labels completely and follow all instructions and requirements listed on the

labels for installation or service.

Installation

Install in accordance with applicable local and national regulations (e.g. NEC).

For Installation in USA: The ProtEX-MAX must be installed in accordance with the National Electrical

Code (NEC) NFPA 70.

For Installation in Canada: The ProtEX-MAX must be installed in accordance with the Canadian Electri-

cal Code CSA 22.1. All power supplies below 36 V and input circuits must be derived from a CSA Ap-

proved Class 2 source.

For European Community: The ProtEX-MAX must be installed in accordance with the ATEX directive

94/9/EC and the product certificate Sira 12ATEX1182.

WARNING

Disconnect from supply before opening enclosure. Keep

cover tight while circuits are alive. Conduit seals must be in-

stalled within 18" (450mm) of the enclosure or within 2"

(50mm) for Zone installations.

Wiring connectors are accessed by opening the enclosure. To access electrical connectors, remove the 2

captive screws and then remove the electronics module. Connectors are on the rear of the electronics

module.

Unpacking

Remove the instrument from packing box. Inspect the packaging and contents for damage. Report dam-

ages, if any, to the carrier.

If any part is missing or the instrument malfunctions, please contact your supplier or the factory for assis-

tance.

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

12

Pre-Installed Conduit/Stopping Plug

The PD8-6000 is supplied with two pre-installed conduit plugs for installations that do not require the use

of all conduit entries. The conduit/stopping plugs include an internal 12mm hexagonal socket recess for

removal. The pre-installed plugs and their installation are included in the hazardous area approvals for

the PD8 Series enclosure.

WARNING

In hazardous areas, conduit and conduit/stopping plugs require

the application of non-setting (solvent free) thread sealant. It is

critical that all relevant hazardous area guidelines be followed

for the installation or replacement of conduit or plugs.

Mounting

The ProtEX-MAX has four slotted mounting flanges that should be used for pipe mounting or wall mount-

ing. Refer to Mounting Dimensions, page 60 for details.

WARNING

Do not attempt to loosen or remove flange bolts

while the instrument is in service.

Cover Jam Screw

The cover jam screw should be properly installed once the instrument has been wired and tested in a

safe environment. The cover jam screw is intended to prevent the removal of the instrument cover in a

flameproof environment without the use of tools. Using a M2 hex wrench, turn the screw clockwise until

the screw contacts the aluminum enclosure. Turn the screw an additional 1/4 to 1/2 turn to secure the

cover. Caution: Excess torque may damage the threads and/or wrench.

Transmitter Supply Voltage Selection (P+, P-)

All controllers, including models equipped with the 12-24 VDC power option, are shipped from the

factory configured to provide 24 VDC power for the transmitter or sensor.

If the transmitter requires 5 or 10 VDC excitation, the internal jumper J4 must be configured

accordingly.

To access the voltage selection jumper:

1. Remove all the connectors.

2. Unscrew the back cover.

3. Slide the back cover about 1 inch.

4. Configure the J4 jumper, located behind the

input signal connector, for the desired

excitation voltage as shown.

Figure 1: Transmitter Supply Voltage Selection

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

13

Connections

WARNINGS

• Static electricity can damage sensitive components.

• Observe safe handling precautions for static-sensitive components.

• Use proper grounding procedures/codes.

• If the instrument is installed in a high voltage environment and a

fault or installation error occurs, high voltage may be present on

any lead or terminal.

• Follow all fusing and wiring precautions requirements for the in-

strument integrated to the PD8 Series model number being con-

nected.

To access the connectors, remove the enclosure cover and unscrew the two captive screws that fasten

the electronics module. Signal connections are made to de-pluggable connectors on the back of the elec-

tronics module.

Some connectors may be provided already connected. These connections are required for proper opera-

tion of the ProtEX-MAX, and should not be removed unless instructed to by this manual.

Wires marked as being used for testing purposes should be removed.

Grounding connections are made to the two ground screws provided on the base – one internal and one

external.

After all connections have been completed and verified, apply power to the unit.

Required & Factory Wired Connection

The ProtEX-MAX comes with a pre-wired connection. This connection is detailed below, and must be

maintained in order for the instrument to function properly.

WARNING

Observe all safety regulations. Electrical wiring should be performed

in accordance with all agency requirements and applicable national,

state, and local codes to prevent damage to the meter and ensure

personnel safety.

Figure 2: Integrated ProVu Required Connections

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

14

Connectors Labeling

The connectors’ label, affixed to the controller, shows the location of all connectors available with

requested configuration.

Warning!

Do not connect any equipment other than Precision

Digital’s expansion modules, cables, or controllers to

the RJ45 M-LINK connector. Otherwise damage will

occur to the equipment and the controller.

Figure 3: Connector Labeling for Fully Loaded PD8-6310

Power Connections

Power connections are made to a two-terminal connector labeled POWER on Figure 6. The controller will

operate regardless of DC polarity connection. The + and - symbols are only a suggested wiring convention.

Figure 4: Power Connections

AC or DC

POWER

Required External Fuse:

5 A max, 250 V Slow Blow

POWER

+

-

C

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

15

Pulse Signal Connections

Signal connections are made to a six-terminal connector labeled SIGNAL on Figure 7. The COM

(common) terminal is the return for the input signals.

The following figures show examples of signal connections.

Setup and programming is performed through the front panel buttons.

Figure 5: Flowmeter Powered by Internal

Power Supply

Figure 6: Flowmeter Powered by External

Supply

Figure 7: Self-Powered Magnetic Pickup

Coil Flowmeter

Figure 8: NPN open Collector Input

Figure 9: PNP Sensor Powered by Inter-

nal Supply

Figure 10: Switch Input Connections

Serial Communication Connections

The ProtEX-MAX has a 5 position terminal block for connecting RS-485 serial devices.

Figure 11 details the wiring connections from the ProtEX-MAX to an RS-485 serial converter (such as the

PDA7485 or PDA8485) for a four-wire network.

ProtEX-MAX to RS-485

Serial Converter Connections

RS-485 Serial

Converter

ProtEX-MAX RS-

485 Connections

DO

DI

DO

DI

DO

DI

DO

Figure 11: ProtEX-MAX Connections to a Serial Converter

The ProtEX-MAX has three diagnostic LEDs: a Power (P) LED to show when the module is powered

properly, a Transmit Data (TX) LED to show when the module is being transmitted to by the PC side, and

a Receive Data (RX) LED to show when the module is sending data to a receiving device.

The following diagrams detail how to connect the RS-485 serial communications from the ProtEX-MAX to

a RS-485/RS-232 serial converter (PDA7485) in four wire and two wire configurations.

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

16

Three Wire Connections

In order to wire the 5 pins for use as a 3-wire half-duplex RS-485 connection, it is necessary to create a

jumper connection between DI – DO and DI- – DO- as shown below.

Figure 12. Three-Wire RS485 Connection

Figure 13: RS-485 Wiring

Notes:

1. Termination resistors are optional and values depend on the cable length and characteristic im-

pedance. Consult the cable manufacturer for recommendations.

2. Refer to RS-232 to RS-485 Converter documentation for further details.

3. Use shielded cable, twisted-pairs plus ground. Connect ground shield only at one location.

WARNING

Observe all safety regulations. Electrical wiring should be performed

in accordance with all agency requirements and applicable national,

state, and local codes to prevent damage to the meter and ensure

personnel safety.

F4 COM DI DI DO DO

TX

RX

1 2 3 4 51 2

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

17

Figure 14: RS-485 Two-Wire Multi-Drop Wiring

Notes:

1. Termination resistors are optional and values depend on the cable length and characteristic im-

pedance. Consult the cable manufacturer for recommendations.

2. Refer to RS-232 to RS-485 Converter documentation for further details.

3. Use shielded cable, twisted-pair plus ground. Connect ground shield only at one location.

WARNING

Observe all safety regulations. Electrical wiring should be performed

in accordance with all agency requirements and applicable national,

state, and local codes to prevent damage to the meter and ensure

personnel safety.

When using more than one instrument in a multi-drop or multi-point mode, each meter must be provided

with its own unique address.

Using PROVU Serial Adapters

NOTICE

PROVU expansion modules and serial adapters are not included in

the hazardous area approvals of the ProtEX-MAX. The PDA1232

may be used only while the ProtEX-MAX is in a safe area, and will

disable some features while installed.

PROVU expansion modules and serial adapters are not recommended for use with the ProtEX-MAX. It is

recommended that any serial protocol conversion required on the RS-485 communications connection be

performed using a PDA7485 RS-232 to RS-485 or PDA8485 USB to RS-485 serial converter located in a

safe area.

!

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

18

Relay Connections

Relay connections are made to two six-terminal connectors labeled RELAY1 – RELAY4 on Figure 7.

Each relay’s C terminal is common only to the normally open (NO) and normally closed (NC) contacts of

the corresponding relay. The relays’ C terminals should not be confused with the COM (common) terminal

of the INPUT SIGNAL connector.

Figure 15: Relay Connections

Switching Inductive Loads

The use of suppressors (snubbers) is strongly recommended when switching inductive loads to prevent

disrupting the microprocessor’s operation. The suppressors also prolong the life of the relay contacts.

Suppression can be obtained with resistor-capacitor (RC) networks assembled by the user or purchased

as complete assemblies. Refer to the following circuits for RC network assembly and installation:

Figure 16: AC and DC Loads Protection

Choose R and C as follows:

R: 0.5 to 1  for each volt across the contacts

C: 0.5 to 1 µF for each amp through closed contacts

Notes:

1. Use capacitors rated for 250 VAC.

2. RC networks may affect load release time of solenoid loads. Check to confirm proper operation.

3. Install the RC network at the controller's relay screw terminals. An RC network may also be installed

across the load. Experiment for best results.

Figure 17: Low Voltage DC Loads Protection

RC Networks Available from Precision Digital

RC networks are available from Precision Digital and should be applied to each relay contact switching an

inductive load. Part number: PDX6901.

Note: Relays are de-rated to 1/14th HP (50 watts) with an inductive load.

C NONO NC NC C

RELAY4 RELAY3

4 36 5 2 1

C NONO NC NC C

RELAY2 RELAY1

4 36 5 2 1

C

R

C

R

Use a diode with a reverse

breakdown voltage two to three

times the circuit voltage and for-

ward current at least as large

as the load current.

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

19

F4 Digital Input Connections

A digital input, F4, is standard on the meter. This digital input connected with a normally open closure

across F4 and COM, or with an active low signal applied to F4.

Figure 18: F4 Digital Input Connections

4-20 mA Output Connections

Connections for the 4-20 mA transmitter output are made to the connector terminals labeled MA OUT.

The 4-20 mA output may be powered internally or from an external power supply.

Figure 19: 4-20 mA Output Connections

Analog Output Transmitter Power Supply

The internal 24 VDC power supply powering the analog output may be used to power other devices, if the

analog output is not used. The I+ terminal is the +24 V and the R terminal is the return.

Interlock Relay Feature

As the name implies, the interlock relay feature reassigns one, or more, alarm/control relays for use as

interlock relay(s). Interlock contact(s) are wired to digital input(s) and trigger the interlock relay. This

feature is enabled by configuring the relay, and relative digital input(s) (see page 41). In one example, dry

interlock contacts are connected in series to one digital input which will be used to force on (energize) the

assigned interlock power relay when all interlock contacts are closed (safe). The interlock relay front

panel LED flashes when locked out. The interlock relay would be wired in-series with the load (N/O

contact). See below.

Figure 20: Interlock Connection

12-35 VDC

Power

Supply

+

4-20 mA

Input Meter

-

+

RI- I+

13 2

RELAY1

3 2 1

24 V

-

4-20 mA Input

Remote Display,

Chart Recorder, Etc.

-

+

RI- I+

MA OUT

13 2

RELAY1

3 2 1

24 V

MA OUT

ProtEX-MAX PD8-6310 Explosion-Proof Pulse Input Batch Controller Instruction Manual

20

Digital I/O Connections

The ProtEX-MAX has a 10 position terminal block for connecting digital inputs and outputs.

Figure 21: Digital I/O Connections

NOTICE

The onboard digital inputs (1-4) are configured at the factory to function

identically to the front panel pushbuttons (Menu, F1, F2, & F3) in order to

work with the SafeTouch buttons. Changing the programming of the digital

inputs will affect the function of the SafeTouch buttons.

If you wish to change the behavior of the digital inputs, re-assign F1-F3 to

the desired function, then change the corresponding digital input to match.

WARNING

Observe all safety regulations. Electrical wiring should be performed in ac-

cordance with all agency requirements and applicable national, state, and

local codes to prevent damage to the meter and ensure personnel safety.

External Switch Contacts

The ProtEX-MAX includes 4 digital inputs. These digital inputs are preconfigured at the factory to function

as external contacts to duplicate the front button functions of the instrument. The factory configuration

uses the following corresponding digital input terminals for external switch contacts.

Digital In-

put Con-

nection

Factory Default Func-

tion

I1

MENU

I2

RIGHT arrow

I3

UP arrow

I4

ENTER arrow

See Digital Inputs & Outputs in the Specification on page 8 for details on the digital inputs.

NOTICE

The digital inputs are configured at the factory to function identi-

cally to the front panel pushbuttons in order to work with the

SafeTouch buttons. Changing the programming of the digital in-

puts will affect the function of the SafeTouch buttons.

1 2 3 4 5 6

+5 I1 I2 I3 I4 O1

7 8

O2 O3

9 10

O4 G

DI 1-4 DO 1-4

5 VDC GND

!

Page is loading ...

PRECISION DIGITAL PD8-6310 User manual

This manual is also suitable for

PRECISION DIGITAL PD8-6310 User manual

Related papers

Other documents