Baratza Sette 30 Replacement Manual

Sette 30
Baratza
Brand
Baratza
Model
Sette 30
Type
Replacement Manual

This manual is also suitable for

Baratza Sette 30 is a versatile coffee grinder that offers precise grind adjustment, consistent results, and a range of grind sizes for various brewing methods. Its features include 30 grind settings, a powerful motor for quick grinding, and a portafilter holder for hands-free grinding. Whether you prefer fine espresso grinds or coarse French press grinds, the Sette 30 delivers uniform particle distribution for optimal flavor extraction.

Baratza Sette 30 is a versatile coffee grinder that offers precise grind adjustment, consistent results, and a range of grind sizes for various brewing methods. Its features include 30 grind settings, a powerful motor for quick grinding, and a portafilter holder for hands-free grinding. Whether you prefer fine espresso grinds or coarse French press grinds, the Sette 30 delivers uniform particle distribution for optimal flavor extraction.

www.baratza.com [email protected]om rev. 9/12/2018
How To: Replace Adjustment Ring Interlock
Switch
Sette 30, 270, 270W, 270Wi
Time: 30 minutes
Difficulty: Medium
Tools/Supplies: T-10 Torx Bit,
Parts: S032
Additional Resources: Sette Case Removal
There are two techniques to changing this switch. Technique 1 is faster but carries slight risk of
damaging the front silver case (while bending the case down as shown in step 5) and is only
recommended for technicians who are comfortable running the risk of causing damage.
Technique 2 requires more disassembly and is longer, but is less likely to cause damage to the
silver case. Please read both techniques to see which one is best for your skill level.
Technique 1 (faster but more difficult)
*** Unplug the grinder from power supply ***
1. Remove the case
2. -WARNING- Although the capacitor will be discharged unless there are
extenuating circumstances, exercise caution as it potentially has a high voltage
charge that can shock you if the contacts are touched.
www.baratza.com [email protected]om rev. 9/12/2018
3. Remove the adjustment assembly, unplug the red and black motor leads,
remove the (4) screws indicated below, and lift out to remove the gearbox/motor
assembly
www.baratza.com [email protected]om rev. 9/12/2018
4. Remove the two short screws indicated below
www.baratza.com [email protected]om rev. 9/12/2018
5. Gently but firmly bent the silver down and away from the black. Use a wedge to
keep a gap between the silver and black portions of the case
6. Pry up the microswitch off the two posts it rests on by using a pick
Burr being used
as a wedge
www.baratza.com [email protected]om rev. 9/12/2018
7. Unplug the leads
8. Plug leads on to new switch
9. Install new switch on posts, taking care to orient the spring steel arm properly
(reference photo above)
10. Remove wedge
11. Replace 2 small screws (do not overtighten)
12. Install gearbox/motor assembly
13. Install case
Mounting posts
Spade connection
electrical leads
Correct orientation
Correct orientation
Incorrect orientation
www.baratza.com [email protected]om rev. 9/12/2018
Technique 2 (longer but easier)
*** Unplug the grinder from power supply ***
1. Remove the case
2. -WARNING- Although the capacitor will be discharged unless there are
extenuating circumstances, exercise caution as it potentially has a high voltage
charge that can shock you if the contacts are touched.
www.baratza.com [email protected]om rev. 9/12/2018
3. Remove the adjustment assembly, unplug the red and black motor leads, remove
the (4) screws indicated below, and lift out to remove the gearbox/motor assembly
www.baratza.com [email protected]om rev. 9/12/2018
4. Unplug the two cables from the display (indicated with yellow arrows)
5. Remove the (2) short screws behind the screen (indicated with red arrows)
6. Remove the (4) screws of the capacitor/PCB bracket (indicated with red)
7. Unplug the 2 pin and 3 pin Molex connectors from the PCB (not indicated – see
step 19 for picture of these connectors)
8. You can lift out the felt rings (indicated with white arrows), or leave them in place.
www.baratza.com [email protected]om rev. 9/12/2018
9. Lift up and remove the capacitor/PCB mount bracket
-continued below-
www.baratza.com [email protected]om rev. 9/12/2018
10. Remove the (10) screws indicated below
11. Remove the front two feet and the screws beneath
12. Partially remove the convertible arm assembly by pulling it towards the rear of
the unit. The hook may need to be adjusted for clearance.
13. Remove the silver front casing. If the silver front casing does not easily remove,
double check that all 14 screws securing it have been removed (2 under front feet,
10 in the back, 2 small screws right behind display)
www.baratza.com [email protected]om rev. 9/12/2018
14. Pry the interlock switch straight up and off the mounting posts
15. Pull the spade clip connectors to remove from the old switch. Push to insert
connectors on to new switch. Install new switch on mounting posts, taking care to
match the orientation of the spring-steel arm with the photo below.
www.baratza.com [email protected]om rev. 9/12/2018
16. Put the silver front case back in position and check that no wires are pinched.
Install the (2) screws under the front feet, and insert the front feet. Continue to
follow these instructions before installing more screws.
17. Route the brown and black interlock switch wires and green display wire (*which
is only on the 270Wi) exactly as shown below.
18. Plug both of the Molex connectors into the PCB, it is much easier to do it before
installing the capacitor/PCB bracket
19. Place the capacitor/PCB bracket in position and inspect wires for routing issues
20. Install (10) screws in back of grinder (reference step 9, will need to slightly lift
capacitor/PCB bracket to access top 2 screws)
Route wires to the
outside of the studs
Route wires to the
outside of the studs
3 pin Molex
connector plugged in
2 pin Molex
connector plugged in
www.baratza.com [email protected]om rev. 9/12/2018
21. Install (4) capacitor/PCB bracket screws, (2) short screws behind display, plug in
(2) wires into PCB noting that the power board to display wire inserts into the top
port (reference step 7)
22. 270W and 270Wi have felt dampening rings between the gearbox/motor
assembly and the chassis. Position as shown in step 8, then install the
gearbox/motor assembly
23. Install case
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Baratza Sette 30 Replacement Manual

Sette 30
Baratza
Brand
Baratza
Model
Sette 30
Type
Replacement Manual
This manual is also suitable for

Baratza Sette 30 is a versatile coffee grinder that offers precise grind adjustment, consistent results, and a range of grind sizes for various brewing methods. Its features include 30 grind settings, a powerful motor for quick grinding, and a portafilter holder for hands-free grinding. Whether you prefer fine espresso grinds or coarse French press grinds, the Sette 30 delivers uniform particle distribution for optimal flavor extraction.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents