Sanyo DVD-SL20 User manual

FILE NO.

Service Manual

CONTENTS

DVD Video Player

DVD-SL20

PRODUCT CODE No.

137 114 03 (UK)

137 114 04 (XE)

137 114 05 (SS)

137 114 06 (PA)

137 114 08 (AU)

REFERENCE No.

SM5810265

Specification ..................................................................... 1

Laser beam safety precaution .......................................... 1

DVD Mechanism replacement ......................................... 2

Mechanism Replacement ................................................ 3

Trouble shooting .............................................................. 5

Service mode ................................................................... 7

How to load software for MPEG P.W.Board .................... 10

Exploded View (Cabinet & Chassis) ................................ 11

Parts List .......................................................................... 12

Exploded View (DVD Mechanism) ................................... 16

Parts List .......................................................................... 16

IC Block Diagram & Description ....................................... 17

Wiring Connection ............................................................ 33

Block diagram (DVD back end) ........................................ 34

(UK)

STANDBY

REMOTE CONTROLLER RB-SL20

NEXTPREV

FWD SLOWREV SLOW

PAUSE/STEP

PLAY

REV FWD

CLEAR

SEARCH

MODE

123C

456

789

0

ENT

SETUP MENU

AUDIO TITLE RETURN

PICTURE

MODE

ANGLE

REPLAY

ZOOM ANGLE

LAST MEMO

SURROUND

ON SCREEN

PROGRAM

OPEN/CLOSE

REPEAT A-B REPEAT

SUBTITLE

CHANGE

SUBTITLE

ON/OFF

(XE)

(SS)

(PA)

(AU)

Schematic Diagram (DVD) ............................................... 36

Schematic Diagram (MPEG/UK, XE) ............................... 38

Schematic Diagram (MPEG/AU, SS, PA) ........................ 40

Wiring Diagram (DVD & MPEG A side) ......................... 42

Wiring Diagram (DVD & MPEG A side Top Left) ........... 44

Wiring Diagram (DVD & MPEG A side Bottom Left) ...... 46

Wiring Diagram (DVD & MPEG A side Top Right) ......... 48

Wiring Diagram (DVD & MPEG A side Bottom Right) ... 50

Wiring Diagram (DVD & MPEG B side) ......................... 52

Wiring Diagram (DVD & MPEG B side Bottom Left) ...... 54

Schematic Diagram (FRONT & DENGEN/UK, XE) ......... 56

Schematic Diagram (FRONT & DENGEN/AU, SS, PA) .. 58

Wiring Diagram (DENGEN)............................................ 60

Wiring Diagram (FRONT)............................................... 62

Wiring Diagram (SCART and MECHA-SW) ................... 64

- 1 -

SPECIFICATIONS

Playback system:

DVD-Video, CD

Playback standard:

PAL or NTSC

Laser:

Semiconductor laser, wavelength: 650/790 nm

Laser output (Continuous wave max.):

1 mW (DVD)

0.5 mW (CD)

Frequency range (digital audio):

4 Hz to 44 kHz (DVD fs: 96 kHz)

Signal to noise ratio:

More than 105 dB

Harmonic distortion (digital audio):

0.003 %

Wow and flutter:

Below measurable level

Outputs:

DIGITAL OUT:

For optical cable

AV EURO CONNECTOR:

For Euro-AV cable

S-VIDEO OUT:

Y: 1.0 Vp-p (75 Ω) NTSC, 1.0 Vp-p (75 Ω) PAL

C: 0.286 Vp-p (75 Ω) NTSC, 0.3 Vp-p (75 Ω) PAL

VIDEO OUT:

1.0 Vp-p (75 Ω)

LASER BEAM SAFETY PRECAUTION

• Pick-up that emits a laser beam is used in this CD player section.

CAUTION :

USE OF CONTROLS OR ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE

LASER OUTPUT.......... 0.6 mW Max. (CW)

WAVELENGTH ............. 790 nm

VIDEO OUT

AUDIO OUT

R L

DIGITAL

OUT

OPT.

S-VIDEO OUT

VIDEO OUT SELECT

S

RGB

AV EURO CONNECTOR

(RGB OUT)

CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE

FOR STRÅLING.

VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD

OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.

VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN

DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.

VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

AUDIO OUT:

L: 2 V rms

R: 2 V rms

Power requirements:

AC 230 - 240 V, 50 Hz(UK, XE, AU)

110 - 120 / 220 - 240 V, 50/60 Hz(SS, PA)

Power consumption:

12 W

Less than 2 W (standby mode)

Dimensions:

360(W) x 63.5(H) x 250(D) mm

Weight:

2.1 kg

This is a basic specifications.

Specifications subject to change without notice.

Illustrator is UK,XE version.

- 2 -

1. Cautionary instructions in handling the assy

(Safety instructions)

Optical pickup

The laser beam used in the pickup is classified as "class 2".

Exposing your eyes or skin to the beam is harmful. Take care

not to do so.

(Caution against static electricity and leakage voltage)

Ground securely the work tables, tools, fixtures, soldering irons

(including those made of ceramic) and measuring instruments

used in the production lines and inspection departments that

handle loaders. The workers shall also be grounded.

(Cautionary instructions in handling)

Do not touch the object lens when handling a loader, or the lens

will be stained, resulting in inadequate playability.

There is no power supply protection circuit provided for this

product or adjustment/inspection device. Short-circuiting may

lead to fire or damage.

Take care so as to protect from exposure to water, the entry of

metallic pieces or dew condensation.

In particular, a strong magnet adjacent to the pickup will not

only get inoperative but can damage the pickup if a small metallic

piece, such as a screw or swarm, enters.

The loader edge can cause injury if inadvertently handled.

Do not touch a rotating disk, or injury may result.

This product is a precision device. Handle carefully.

A shock or dropping will cause misalignment or destruction. If it

should occur, refer to clause 2.

This product is so designed as to endure an initial shock

equivalent to a drop from a height of approx. 90 cm under the

packed condition.

After the initial shock, the resistivity will still remain at a level of

50 to 60 G, but the mechanical robustness will weaken.

Do not place in a dusty location.

The entry and deposition of dirt into or on the pickup lens or

moving section will cause malfunction or degradation.

DVD MECHANISM REPLACEMENT

(Connectors)

Do not connect or disconnect while power is on.

Connecting or disconnecting signal wires or the main power cord

when the power is on may destruct the unit or fixture.

When connecting, push all the way in securely.

An insufficient insertion may cause a bad contact, leading to an

erroneous operation.

Do not connect or disconnect roughly by an excessively strong

force, or a broken wire or bad contact may result.

Semiconductors are connected. Do not touch connector

terminals directly.

If the worker is grounded, there is nothing to worry about static

electricity, but the rust on the connector terminal surface caused

by the touch may result in bad contact.

(Caution)

Before disconnecting FFC

cable, make it "SHORT" as

shown left.

After connecting FFC

cable,make it "OPEN" as

shownleft.

(Power source)

The power source need be good in quality (free from

instantaneous interruptions or noises).

A low quality power source may well cause malfunction.

(Storage)

Do not place or store in a dusty place or a place where dew

condensation is possible.

The entry and deposition of dirt or dust into or on the pickup lens

or moving section will cause malfunction or degradation.

Also, dew condensation causes rust; the rust penetrate into the

precision part of a pickup, causing malfunction, or degrading

the optical quality of the internal lens and reflector, which also

leads to malfunction.

(OPEN)(SHORT)

- 3 -

MECHANISM REPLACEMENT

3. How to install the motor.

1. How to remove the tray.

2. How to insert the tray.

1

2

1

2

1

2

Rotate the 1 gear.

Move forward the 2 tray.

Move both the right and left 1 tray pins to the ends.

Remove the 2 tray.

Move the 1 slide to the left end.

Insert the 2 tray.

3

2

4

1

TERMINAL

ROUND

HOLE

ROUND

HOLE

SHASSIS

TRIANGLE

MARK

BOSS

SOLDERING

MECHA

P. W. B

1 Adjust the motor terminal to boss in the chassis.

2 Adjust the round hole of the motor to the triangle mark of

P.W.B,and solder it.

- 4 -

Do not remove the pick-up from base mechanism because of

adjustment difficulty.

GREASE

CDF-409

GREASE

CDF-409

GREASE

CDF-409

GREASE

EM-30LG

GREASE

EM-30LG

A

: Clean the groove by alcohol well.

A

GREASE

EM-30LG

GREASE

EM-30LG

Apply screw lock

GREASE

EM-30LG

GREASE

EM-30LG

4. Base mechanism mounting parts.

5. Base mechanism parts.

6. Tray parts.

MECHANISM REPLACEMENT

- 5 -

TROUBLE SHOOTING

Is t

h

ev

O

lt

ag

eat

4

and 5 of CN

81

1

about 5. 5V

?

POW

ER DO ES NOT

TU

RN

ON

DOE

S

NOT LI

GHT

DISPLA

Y

N

Check IC483 and peri

pher

al

circui

t.

Is

th e volt age at pi n

3

of IC852 about 5. 0V

?

Is the volt

ag

e

at pin

3

of IC851

ab

out 3. 3V?

Ch

eck

IC852 and peri

ph

er

al

circ

uit.

Chec

k

IC851 and peri

ph

eral

circui t.

Y

N

Y

N

Ch

eck FL1 li

ne

of

PO

WE

R

BL

OC

K.

Is

the volt

ag

e

at

pi n1 and 2 of FL601

abou

t

-2 8V

?

N

Y

Re

plac e FL601 or IC60

1.

LOADER DOES NOT ACCEPT OPEN/CLOSE

Is

th e voltage at pi

n

10

an

d22

of IC160about

9V

?

Is

th

e

lose conn

ec

tion

at

CN

10

0,

CN

15

0,CN

16

0, CN

161

an

d

CN

16

2

to

LOAD

ER

.

N

Ch eck 9V li

ne

of

PO

WE

RBLOC

K.

Y

Ch

eck

each other connecti

on

to

LOAD

ER

.

N

Ch

eck IC800 and

pe

ri

ph

er

al

circ

uit.

Wh

en

AC IN,

LOAD

ERMOTOR turn

?

Ch

ec

kOPENorSH

OR

Tat pin 64,6 8, 73

an

d

74 of IC80

0.

Is th e volt ag

e

at pi n

3

of IC850 about 1. 9V?

Check IC850 and peri

ph

eral circui

t.

N

Y

Is th er e wavefo rm at

X800

0

about 3. 0Vp-p?

Ch

ec

k

X800

0,

IC800 and peri

pheral

circ uit.

Rewrit e ROM DA

TA

.

N

Y

N

Is th e volt

ag

e

at

pi n

31

and 32 of FL601

abou

t

-2 5V

?

Is the voltag

e

at

pi n

13

and 43 of IC601

abou

t

5V

?

Is th

e

voltag

e

at pi

n

30

of IC601

abou

t

-3 0V

?

Check FL2 line of

POWE

R

BLOC

K.

Check IC852 and

peri

pheral ci

rc

uit.

Check -30V line of

PO

WE

R

BL

OC

K.

N

Y

PICTURE mode

is

BLACKand

WH

IT

E?

Change PICTUR

E

mo

de to

STANDA

RD .

Y

N

NO

CO

LOR

PLAYBACK PI

CTUR

E

OF

COMPOSI

TE

VIDE

O

OUT

X8230 osc is

27

.000

MH

z?

CheckX8

230

and peri

ph

er

al

circui

t.

N

Y

Check IC820 or

change IC820.

- 6 -

TROUBLE SHOOTING

Is ther

e

VI

DEO signal

at pin 103 of IC820.

NO PLAYBA

CK

PICTURE OF COMPOS

IT

E

VI

DE

O

OU

T

NO PLAY

BA

CK

PI

CTURE

OF

S-VIDEO OUT

N

Y

Ch

ec

kCN87

0

and peripher

al

circ

ui

t.

Is

th

ere

wa

ve

fo

rm

from

147 to pi

n

159 of

IC

820?

Chec

k

IC130 and peri

ph

er

al

circuit.

Y

N

Sele

ct

S-VIDE

O

side.S8400 is S-VIDE

O

side?

N

Y

Check IC820 or

change IC820.

Is

th

ere

VIDEO

si

gnal at

pi

n

105 and 106 of IC82

0?

S8400 is

CO

MPONEN

T

VIDEO

si

de

?

Check CN872 and peripher

al

circ

ui

t.

Sele

ct

COMPON

EN

T

si

de

.

Y

N

Y

A

NO PL

AYBACK

PI

CUREOF COMPONENT

VIDEO(UK,XE:RGB)

OUT

Is

there

VIDE

O

si

gnal at

pin 102,105 an

d

106 of

IC82

0?

Ch

eck CN870 and peripher

al

ci

rcui

t.

Y

N

A

NO

DI GITA

L

AUDI O OUT ON PLAYBACK

Is there wa

veform

at

pi

n

4

of IC859?

Is

the volt

age

at pi n

5

of IC859 about 3. 3V?

Y

Ch

ec

kIC871 and peripher

al

circuit.

N

Check IC851 and periph

er

al ci

rc ui

t.

Y

Ch

eck IC130 and peri

ph

eral

circui

t.

Is

there waveform at

pi

n

13,1 4, 15 and 16 of IC87

1?

Ch

ec

k

IC800 and peri

ph

eral circ

ui

t.

Y

N

Is

ther

e

wa

veform at

pi

n

13,1 4, 15 an

d

16 of

IC87

1?

Pi n 6 of IC859

is LO

W?

B

C

Y

Pi n 6 of IC859

is HIGH

?

B

C

NO

AN

AL

OG AU

DI

O

OU

T

ON PLAY

BACK

Is

there AUDIO signal

at

pi

n

7and8of IC871?

Is there waveform at pi

n

1, 2 and3of IC871?

Y

Ch

eck IC872,Q8720, Q8820 and

peri

ph

eral ci

rc ui

t.

N

Check IC820 and peri

ph

eral circ

ui

t.

Y

Check IC871 or

change IC871.

Is th er e wavefo rm at pi n

13,1 4, 15 and 16 of IC87

1?

Check IC800, IC820 and periph

eral

ci

rcui

t.

N

Y

N

Ch

ange IC859.

B

C

Y

N

(UK,XE:RGB)

- 7 -

SERVICE MODE

B. How to enter Service Mode.

You can enter Service Mode in any one of the following ways (1 to 3).

1. Using the buttons on the main unit

Immediately (within one second) after pushing both STOP and POWER buttons simultaneously, push PREV button.

A. Market / Region SETUP

In the initial condition for this model, Market and Region

information are undefined.

In the following cases, be sure to set up Market/Region.

1. When updating the system using CD-R

(Part code : 0PRADD711400A).

2. When replacing a DVD substrate.

While Market/Region information are undefined, the message

"Region Undefined" is displayed on the screen.

NOTE: Even if the condition is not under 1 or 2 above, if the

message "Region Undefined" is displayed, be sure to set up

Market/Region.

2. Pushing the covered key located beneath Book Mark key on RB-

1500 or REM-S1500.

3. Simultaneously pushing both Shift key and ON SCREEN key on

REM-A8501/US

- 8 -

SERVICE MODE

C. Setup Procedures

1. Displaying SERVICE MODE screen

Display Service Mode screen following the instructions "How to

enter Service Mode" above.

2. Displaying Internal Setup screen

Push NEXT button within three seconds after operating the Service

Mode display.

On the Internal Setup screen shown on the right, set up Market and

Region.

3. Setting Market code

3.1. While a highlighted indicator is displayed on the right side of the

Market denotation, push ENT button on the remote controller.

With each push the indicator will advance as shown below.

WM -> SFC -> EUR -> S18 -> SS -> PA

3.2. Specify the code of the model in accordance with the Market/

Region Setup Table above.

(In DWM-380 model, the code is the same as the initial one

"WM". Advance to the next procedure without making any

changes.)

3.3 Once the desired code is displayed, push p button to move the

highlighted indicator to the Region input area.

Market/Rejion setup table.

Model

Market Region

DWM-380/US

WM 1

DVD-SL20/CA

WM 1

DVD-SL18/CA

S18 1

DVD-SL20/UK

EUR 2

DVD-SL20/XE

EUR 2

DVD-SL20/AU

EUR 4

DVD-SL20/SS

SS 1 - 6

DVD-SL20/PA

PA 1 - 6

- 9 -

SERVICE MODE

4. Setting REGION code

4.1 While a highlighted indicator is displayed on the right side of

the Region denotation, push ENT button on the remote

controller. With each push the indicator will advance as

shown below.

1 -> 2 -> 3 -> 4 -> 5 -> 6

4.2 Specify the number of the model in accordance with the

Market/Region Setup Table above.

(In DWM-380/US models, the number is the same as the

initial one "1". Advance to the next procedure without making

any changes.)

4.3 Once the desired number is displayed, push p button to move

the highlighted indicator to Exit area.

5. Saving settings

5.1 Make sure that the Market and Region settings are properly

set.

(If any of the settings are incorrect, you can make a change

by moving the indicator using p button, and following

procedures 3 and 4 above. )

5.2 After ensuring that the settings are all correct, push ENT

button while the indicator is on Exit area. The settings are

now saved.

6. Finishing settings

6.1 After a few seconds, the Internal Setup screen disappears,

and then the Service Mode screen is displayed again for

three seconds as shown on the right.

You should check the settings.

Backend version

S 11225 A 0

Brand (S : SANYO , F : FISHER)

Version ( 2 0 0 1 , 12 , 25)

Sub Version (A,B,......Z)

Region ( 0 : Region undefined

1 ~ 6 : Region defined

F : Region Free )

6.2 Power OFF.

- 10 -

SERVICE MODE

D. IMPORTANT NOTE

1. Once the "Market/Region" settings are written into EEPROM (IC801) on the DVD substrate, they cannot be reset.

(However, updating the system using CD-R enables you to make new settings.)

2. While the Internal Setup screen is displayed, pushing the Power button enables you to terminate the operations without

making any settings.

HOW TO LOAD SOFTWARE FOR MPEG P.W.BOARD

1. Power on, then open tray.

2. It take on CD-ROM for UPDATE software to the tray, and tray close.

3. Display " UP DATE" in the TV screen.

4. For the time being, tray open and FL display remain "UP DATE".

5. When software loading finished, FL display "STANDBY".

6. Next, set up market code and region code by "SERVICE MODE"

CD-ROM part code is "0PRADD711400A".

- 11 -

EXPLODED VIEW (CABINET & CHASSIS)

Y10

8

Y02

1

2

3

11

10

53

7

9

12

4

5

6

71

Y01

Y03

Y04

Y06

Y07

Y09

Y08

Y05

Y03

Y01

73

72

51

52

55

13

54

56

57

74

- 12 -

PARTS LIST

PRODUCT SAFETY NOTICE

EACH PRECAUTION IN THIS MANUAL SHOULD BE FOLLOWED DURING SERVICING. COMPONENTS IDENTIFIED WITH THE

IEC SYMBOL

!

!!

IN THE PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATED COMPONENTS IN WHICH SAFETY CAN

BE OF SPECIAL SIGNIFICANCE. WHEN REPLACING A COMPONENT IDENTIFIED BY

!

!!

, USE ONLY THE REPLACEMENT

PARTS DESIGNATED, OR PARTS WITH THE SAME RATINGS OF RESISTANCE, WATTAGE OR VOLTAGE THAT ARE DESIGNATED

IN THE PARTS LIST IN THIS MANUAL. LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS MUST BE MADE TO

DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE

PRODUCT TO THE CUSTOMER.

CAUTION : Regular type resistors and capacitors are not listed. To know those values, refer to the schematic diagram.

Regular type resistors are less than 1/4 W carbon type and chip resistors.

Regular type capacitors are less than 50 V and less than 1000 µF type of Ceramic type and Electrical type.

PACKING & ACCESSORIES

REF.NO. PART NO. DESCRIPTION

614 320 4077 CUSHION,TOP

614 320 4084 CUSHION,BOTTOM

614 322 4259 CARTON CASE,INNER(XE)

614 322 4266 CARTON CASE,INNER(SS)

614 323 8379 CARTON CASE,INNER(PA)

614 323 8386 CARTON CASE,INNER(AU)

614 322 4334 CUSHION,SPACE(AU)(UK)

614 323 3985 CARTON CASE,INNER(UK)

614 322 4341 CUSHION,PAD(AU)(UK)

614 322 4358 INSTRUCTION MANUAL,INST(XE)

614 322 4365 INSTRUCTION MANUAL,INST(UK)

614 322 4389 INSTRUCTION MANUAL,GREEK,

INST(XE)

614 323 8447 INSTRUCTION MANUAL,INST(AU)

614 323 8454 INSTRUCTION MANUAL,INST(SS)

614 323 8461 INSTRUCTION MANUAL,INST(PA)

614 323 8645 CUSHION,PAD

645 011 9736 POLY BAG,

INST MANUAL(AU)(PA)(SS)

645 012 2958 POLY BAG,INST MANUAL(UK)

645 013 6535 POLY BAG,INST MANUAL(XE)

645 036 4358 POLY SHEET,SET(AU)(PA)(SS)(UK)

645 036 4365 POLY SHEET,SET(XE)

645 048 2182 POLY BAG,CABLE(XE)

645 052 1416 POLY BAG,AC CODE(UK)

645 052 1621 POLY BAG,CABLE(AU)(PA)(SS)(UK)

645 003 3414 CABLE,A/V(-3)

645 052 2352 REMOCON,RB-SL20

645 048 5053 BATTERY COVER,SERVICE PART

645 006 4630 PLUG,ADAPTOR AC,

PLUG ADAPTOR(PA)(SS)

or 645 017 2175 PLUG,ADAPTOR AC,

PLUG ADAPTOR(PA)(SS)

645 037 3893 CABLE,A/V(-3)

or 645 023 0806 CABLE,A/V(-3)

or 645 017 6012 CABLE,A/V(-3)

CABINET & CHASSIS

REF.NO. PART NO. DESCRIPTION

1 614 322 4525 ASSY,DEC,DVD TRAY

2 614 323 4135 ASSY,CABINET,

FRONT(AU)(XE)(UK)

2 614 323 8010 ASSY,CABINET,FRONT(PA)(SS)

3 614 321 2126 BUTTON,OPEN/CLOSE

4 614 320 3766 BUTTON,PLAY

5 614 320 3889 CAP,BUTTON,PLAY,CAP PLAY

6 614 302 0530 DEC,WINDOW LED,STANDBY

7 614 320 3773 BUTTON,POWER

8 614 321 2331 ASSY,CABINET,BENDING,

AFTER BENDING

9 614 320 3728 ASSY,CABINET,BOTTOM

10 614 313 6545 SPRING,PLATE,SHIELD

11 614 129 1901 FIXER,AC CORD

or 614 284 1884 FIXER,AC CORD

12 614 321 8951 PANEL,REAR(UK)

12 614 321 8968 PANEL,REAR(XE)

12 614 323 8225 PANEL,REAR(AU)

12 614 323 8232 PANEL,REAR(SS)

12 614 323 8249 PANEL,REAR(PA)

13 614 322 5997 MOUNTING,FFC,

FIXING PARTS

REF.NO. PART NO. DESCRIPTION

Y01 411 165 3803 SCR S-TPG BIN 2.3X10,

FRONT PWB FIX

Y02 411 098 4205 SCR S-TPG BIN 3X8,CABINET

Y03 411 020 9803 SCR S-TPG BRZ+FLG 3X6,

DVD MECHA

Y04 411 021 6405 SCR S-TPG BIN 3X8,DG PWB

Y05 614 130 0382 LUG,AC_CORD_FIX

Y06 411 021 6405 SCR S-TPG BIN 3X8,MPEG PWB

Y07 411 021 6405 SCR S-TPG BIN 3X8,

SPRING PLATE

Y08 411 021 3701 SCR S-TPG BIN 3X10,

BOTTOM-REAR

Y09 411 021 3701 SCR S-TPG BIN 3X10,

REAR-ELECT PART

Y10 411 021 2704 SCR S-TPG BIN 2.6X6,MOUNTING

ELECTRICAL-PARTS

REF.NO. PART NO. DESCRIPTION

51 423 028 8207 FUSE 250V 1A,250V 1A(UK)(XE)

51 423 028 8207 FUSE 250V 1A,

T1A L 250V(AU)(PA)(SS)

52 614 323 3237 ASSY,WIRE,

LOADING-DVD(AU)(PA)(SS)(UK)

53 614 255 2513 POWER CORD(PA)(SS)(XE)

or 645 016 9939 CORD,POWER-1.74MK(PA)(SS)(XE)

53 645 032 1887 CORD,POWER-2.0MK,FOR AU(AU)

or 614 256 5308 POWER CORD,FOR AU(AU)

53 645 036 9797 CORD,POWER-1.6MK,FOR UK(UK)

or 645 036 9803 CORD,POWER-1.6MK,FOR UK(UK)

or 645 054 0233 CORD,POWER-1.6MK,FOR UK(UK)

54 614 323 3206 ASSY,WIRE,DVD-DG

55 645 053 8384 FLEXIBLE FLAT CABLE,

PICK-FFC(UL2896-24-P0.5-250MM)

56 645 031 7637 CORE,FERRITE,AC_CORD

or 645 051 0649 CORE,FERRITE,AC_CORD

57 645 053 8506 FLEXIBLE FLAT CABLE,IF-FFC

(UL2896-8-P1.0-140MM)

FRONT P.W.BOARD ASSY

REF.NO. PART NO. DESCRIPTION

71 614 320 6149 PWB,ASSY FRONT(Only initial)

(SS)(PA)(AU)

71 614 322 1098 PWB,ASSY FRONT(Only initial)

(UK)(XE)

BR601 614 315 5843 HOLDER,FL

CN601 614 323 3213 ASSY,WIRE,FRONT_DVD

D6001 407 012 4406 DIODE 1SS133

D6002 407 012 4406 DIODE 1SS133

D6040 407 012 4406 DIODE 1SS133

D6041 407 012 4406 DIODE 1SS133

D6042 407 012 4406 DIODE 1SS133

D6044 407 012 4406 DIODE 1SS133(SS)(PA)(AU)(PA)

D6045 407 012 4406 DIODE 1SS133(SS)(PA)(AU)(PA)

D6046 407 012 4406 DIODE 1SS133(SS)(PA)(AU)(PA)

D6051 407 012 4406 DIODE 1SS133(UK)(XE)

D6052 407 012 4406 DIODE 1SS133(UK)(XE)

D6053 407 012 4406 DIODE 1SS133(UK)(XE)

D6054 407 012 4406 DIODE 1SS133(UK)(XE)

- 13 -

PARTS LIST

REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. DESCRIPTION

D6055 407 012 4406 DIODE 1SS133(UK)(XE)

D6401 408 032 5404 LED SLP-9118C-51H-S-T1,

STANDBY

DS601 407 220 6803 PHOTO DIODE SPS-444-1-G1

FL601 645 044 8232 FLUORESCENT TUBE

IC601 409 519 6907 IC PT6315

IC602 410 437 5309 IC M34506M2-713FP(UK)(XE)

Q6051 405 151 5209 TR KRA107M(UK)(XE)

or 405 000 0904 TR DTA114YS(UK)(XE)

Q6052 405 151 5209 TR KRA107M(UK)(XE)

or 405 000 0904 TR DTA114YS(UK)(XE)

Q6053 405 151 5209 TR KRA107M(UK)(XE)

or 405 000 0904 TR DTA114YS(UK)(XE)

Q6054 405 110 5400 TR KRA102M-A(UK)(XE)

or 405 000 0508 TR DTA114ES(UK)(XE)

Q6055 405 151 5209 TR KRA107M(UK)(XE)

or 405 000 0904 TR DTA114YS(UK)(XE)

Q6056 405 109 9402 TR KRC111M(UK)(XE)

or 405 000 3400 TR DTC114TS(UK)(XE)

S6040 645 048 3820 SWITCH,PUSH

or 614 220 5471 SWITCH,TACT

or 614 240 1002 SWITCH,TACT

or 645 006 5958 SWITCH,PUSH 1P-1T

S6041 645 048 3820 SWITCH,PUSH

or 614 220 5471 SWITCH,TACT

or 614 240 1002 SWITCH,TACT

or 645 006 5958 SWITCH,PUSH 1P-1T

S6042 645 048 3820 SWITCH,PUSH

or 614 220 5471 SWITCH,TACT

or 614 240 1002 SWITCH,TACT

or 645 006 5958 SWITCH,PUSH 1P-1T

S6044 645 048 3820 SWITCH,PUSH

or 614 220 5471 SWITCH,TACT

or 614 240 1002 SWITCH,TACT

or 645 006 5958 SWITCH,PUSH 1P-1T

S6045 645 048 3820 SWITCH,PUSH

or 614 220 5471 SWITCH,TACT

or 614 240 1002 SWITCH,TACT

or 645 006 5958 SWITCH,PUSH 1P-1T

S6046 645 048 3820 SWITCH,PUSH

or 614 220 5471 SWITCH,TACT

or 614 240 1002 SWITCH,TACT

or 645 006 5958 SWITCH,PUSH 1P-1T

X6051 645 013 7532 OSC,CERAMIC 4.19MHZ(UK)(XE)

DENGEN P.W.BOARD ASSY

REF.NO. PART NO. DESCRIPTION

72 614 323 7440 PWB,ASSY DENGEN(Only initial)

(SS)(PA)(AU)

72 614 322 1104 PWB,ASSY DENGEN(Only initial)

(UK)(XE)

C4809 403 357 8406 ELECT 1000U M 6.3V

C4811 403 337 2103 ELECT 100U M 10V

or 403 373 8305 ELECT 100U M 10V

C4812 403 337 5500 ELECT 22U M 50V

or 403 374 0704 ELECT 22U M 50V

C4814 403 373 8800 ELECT 330U M 16V

C4815 403 337 7207 ELECT 33U M 35V

or 403 374 0001 ELECT 33U M 35V

C4900 403 348 1508 MT-POLYEST 0.022U K 400V

(UK)(XE)

C4901 403 082 0201 POLYPRO 470P J 100V(UK)(XE)

C4902 403 082 0201 POLYPRO 470P J 100V

C4903 403 332 7202 ELECT 47U M 25V

or 403 373 9203 ELECT 47U M 25V

C4904 403 145 9103 CERAMIC 220P K 1K

C4906 404 088 7409 MT-POLYEST 0.1U K 250V

or 404 080 8206 MT-POLYEST 0.1U K 250V

or 403 376 2409 MT-POLYEST 0.1U M 250V

C4907 404 088 7409 MT-POLYEST 0.1U K 250V

or 404 080 8206 MT-POLYEST 0.1U K 250V

or 403 376 2409 MT-POLYEST 0.1U M 250V

C4908 404 080 8107 CERAMIC 2200P M 400V

CN481 614 310 2557 PLUG,14P

or 645 006 0892 PLUG,14P

D4802 408 043 6704 DIODE RGP10GL-22C-012

D4803 408 044 7304 DIODE SB160L-19C2-004

D4805 408 043 6704 DIODE RGP10GL-22C-012

D4806 408 043 6704 DIODE RGP10GL-22C-012

D4807 407 099 4603 ZENER DIODE MTZJ3.9B

D4809 408 044 6307 DIODE SB140L 19C2-004

D4820 407 099 6607 ZENER DIODE MTZJ12B

D4900 408 043 6803 DIODE RGP02-15EL-22C-012

(UK)(XE)

D4901 407 012 4406 DIODE 1SS133(UK)(XE)

D4902 407 012 4406 DIODE 1SS133

D4903 407 012 4406 DIODE 1SS133(UK)(XE)

D4904 407 004 9808 DIODE DSK10E

or 407 012 0408 DIODE 1N4004

or 407 004 9808 DIODE DSK10E

D4905 407 004 9808 DIODE DSK10E

or 407 012 0408 DIODE 1N4004

or 407 004 9808 DIODE DSK10E

D4906 407 004 9808 DIODE DSK10E

or 407 012 0408 DIODE 1N4004

or 407 004 9808 DIODE DSK10E

D4907 407 004 9808 DIODE DSK10E

or 407 012 0408 DIODE 1N4004

or 407 004 9808 DIODE DSK10E

D4910 407 012 4406 DIODE 1SS133

FPC01 645 006 4760 HOLDER,FUSE

or 645 031 7903 HOLDER,FUSE

FPC02 645 006 4760 HOLDER,FUSE

or 645 031 7903 HOLDER,FUSE

HS491 614 215 9347 HEAT SINK(UK)(XE)

IC483 409 517 5704 IC KA431AZTF

or 409 508 2804 IC KIA431A

or 409 508 2705 IC KIA431

or 409 067 7203 IC L5431

IC490 410 431 1208 IC STR-G6351 LF1129(SS)(PA)(AU)

IC490 409 460 3109 IC STR-G6651(UK)(XE)

L4801 645 048 4469 INDUCTOR,22U

or 645 045 8613 INDUCTOR,10U

L4900 645 045 8941 LINE FILTER

or 645 038 2024 LINE FILTER

PC490 408 047 0005 PHOTO COUPLE H11A817B300

or 407 220 4601 PHOTO COUPLE PC123Y22

(SS)(PA)(AU)

PC491 408 047 0005 PHOTO COUPLE H11A817B300

(UK)(XE)

or 407 220 4601 PHOTO COUPLE PC123Y22

(UK)(XE)

PR481 645 042 2553 PROTECTOR,0.63A 125V

PR482 645 042 2560 PROTECTOR,0.75A 125V

PR484 645 042 2553 PROTECTOR,0.63A 125V

PT490 645 045 6473 TRANS,POWER,PULSE

Q4820 405 141 3109 TR KTC3203-Y

or 405 024 9907 TR 2SD734-F

or 405 025 0200 TR 2SD734-G

Q4821 405 109 9204 TR KRC102M-A(UK)(XE)

or 405 000 3103 TR DTC114ES(UK)(XE)

Q4822 405 109 9204 TR KRC102M-A(UK)(XE)

or 405 000 3103 TR DTC114ES(UK)(XE)

Q4851 405 109 9204 TR KRC102M-A(UK)(XE)

or 405 000 3103 TR DTC114ES(UK)(XE)

Q4852 405 141 3109 TR KTC3203-Y(UK)(XE)

or 405 024 9907 TR 2SD734-F(UK)(XE)

or 405 025 0200 TR 2SD734-G(UK)(XE)

Q4853 405 143 6504 TR KTA1267-GR(UK)(XE)

or 405 004 4601 TR 2SA608-F-SPA(UK)(XE)

or 405 004 5103 TR 2SA608-G-SPA(UK)(XE)

or 405 006 1806 TR 2SA933S-R(UK)(XE)

or 405 006 1905 TR 2SA933S-S(UK)(XE)

Q4854 405 143 6504 TR KTA1267-GR(UK)(XE)

or 405 004 4601 TR 2SA608-F-SPA(UK)(XE)

or 405 004 5103 TR 2SA608-G-SPA(UK)(XE)

or 405 006 1806 TR 2SA933S-R(UK)(XE)

or 405 006 1905 TR 2SA933S-S(UK)(XE)

Q4856 405 141 3703 TR KTA1271-Y(UK)(XE)

- 14 -

PARTS LIST

REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. DESCRIPTION

or 405 008 2405 TR 2SB698-F(UK)(XE)

or 405 008 2504 TR 2SB698-G(UK)(XE)

Q4857 405 143 6504 TR KTA1267-GR(UK)(XE)

or 405 004 4601 TR 2SA608-F-SPA(UK)(XE)

or 405 004 5103 TR 2SA608-G-SPA(UK)(XE)

or 405 006 1806 TR 2SA933S-R(UK)(XE)

or 405 006 1905 TR 2SA933S-S(UK)(XE)

Q4858 405 109 9402 TR KRC111M(UK)(XE)

or 405 000 3400 TR DTC114TS(UK)(XE)

R4908 402 087 3408 RESISTOR 3.3M J- 1/2W

or 402 078 9501 CARBON 3.3M J- 1/2W

or 402 078 8108 CARBON 3.3M J- 1/2W

SCR41 411 021 6405 SCR S-TPG BIN 3X8(UK)(XE)

WR490 614 017 8203 TERMINAL BOARD

WR491 614 017 8203 TERMINAL BOARD

DVD/MPEG P.W.BOARD ASSY

REF.NO. PART NO. DESCRIPTION

73 614 323 2964 ASSY PWB DVD/MPEG(Only initial)

(UK)(XE)

73 614 323 2971 ASSY,PWB DVD/MPEG(Only initial)

(SS)(PA)(AU)

C1050 403 373 9203 ELECT 47U M 25V

C1901 403 373 7902 ELECT 150U M 6.3V

C8535 403 373 7902 ELECT 150U M 6.3V

CN100 645 037 6207 SOCKET,FFC 24P

CN160 614 310 2465 PLUG,5P

or 645 005 9292 PLUG,5P

CN162 645 043 8882 SOCKET,FPC 8P

CN811 614 310 2557 PLUG,14P

or 645 006 0892 PLUG,14P

CN814 614 310 2557 PLUG,14P

or 645 006 0892 PLUG,14P

CN870 645 041 1694 JACK,RCA-3(UK)(XE)

CN870 645 041 1298 JACK,RCA-6(SS)(PA)(AU)

CN871 407 223 4004 PHOTO COUPLE GP1FA551TZ

or 407 221 6406 PHOTO COUPLE TOTX179

CN872 645 044 9086 SOCKET,DIN 4P

CN891 614 310 2533 PLUG,12P(UK)(XE)

or 645 006 0878 PLUG,12P(UK)(XE)

D1101 407 221 1807 DIODE KDS120E

or 407 179 1805 DIODE DAP222

D1102 407 221 1906 DIODE KDS121E

or 407 162 8507 DIODE DAN222

D8531 407 206 5608 ZENER DIODE UDZS10B

D8801 407 221 6505 ZENER DIODE KDZ5.6V

or 407 208 9703 ZENER DIODE UDZS5.6B

or 407 179 4608 ZENER DIODE UDZ5.6B

D8880 407 149 0807 DIODE 1SS355

D8881 407 224 8605 DIODE KDS226

IC100 409 482 3903 IC LA9702WL-MPB

IC101 409 521 9606 IC CD4066BCM

IC130 409 500 6404 IC LC78661W-D

IC141 409 447 3702 IC T224162B-35S

or 410 367 3604 IC LC324265AT-25DV-TLM

or 409 447 3702 IC T224162B-35S

or 410 375 9407 IC LC324265AT-25DV-MPB

or 410 388 4505 IC M11B416256A-35T

IC160 409 520 8303 IC LA6560

IC800 409 522 0701 IC ZR36705TQC

IC801 410 430 9601 IC S524C20D21-SCT0

or 410 429 7809 IC S524C20D21-SCB0

or 410 429 7908 IC AT24C02N-10SI-2.7

IC802 409 505 0803 IC PST3627U

IC806 410 430 9403 IC 74VHCT08AMTCX

IC818 410 430 9502 IC ASSY(IC LE28DW8163T-70T-MPB)

IC820 410 422 1408 IC ZR36732

IC821 409 482 0209 IC K4S161622D-TC80

IC850 409 509 9208 IC PQ070XZ01Z

IC851 409 509 9208 IC PQ070XZ01Z

IC852 409 509 9208 IC PQ070XZ01Z

IC859 409 489 9700 IC NC7SZ157P6

IC871 409 500 3304 IC PCM1748E,DAC_2CH

IC872 409 426 1903 IC KIA4558F

or 409 039 7804 IC NJM4558M

L1001 645 034 7887 INDUCTOR,1000 OHM