Sanyo DC-DA1000 User manual

Category
Cassette players
Type
User manual
Service Manual
FILE NO.
Micro Component System
DC-DA1000 (AU)
PRODUCT CODE No.
129 648 05
REFERENCE No.
SM5810407
This service manual consists of "DC-DA1000U/AU" (Main unit : 129 647 05) and
"SX-DA1000/UK" (Speaker system : 165 064 00).
Contents
Laser beam safety precaution..........................................1
CD pick-up maintenance..................................................1
Tape adjustments ............................................................1
Tuner adjustments ...........................................................2
Exploded view
(Cabinet & Chassis) ......................................................3
Parts list ...........................................................................4
Exploded view & Parts list (Tape mechanism)...............7
IC block diagram & description ........................................8
LCD display description ...................................................13
Schematic diagram
(FRONT) .......................................................................14
(CD)...............................................................................16
(TUNER) .......................................................................20
(AMPLIFIER )................................................................24
Wiring diagram
(FRONT & CD)..............................................................18
(TUNER) .......................................................................22
(AMPLIFIER).................................................................26
(POWER TRANSFORMER & LED) ..............................28
Wiring connection ............................................................29
CD
- 1 -
LASER BEAM SAFETY PRECAUTION
• Pick-up that emits a laser beam is used in this CD player section.
TAPE ADJUSTMENTS
R / P HEAD
RED
WHITE
YELLOW EARTH
b. Adjusting head azimuth
1. Load a test tape (VTT-738, etc. :10kHz) for
azimuth adjustment.
2. Press the PLAY button.
3. Use a cross-tip screwdriver to turn the screw for
normal azimuth adjustment so that the left and right
outputs are maximized at the same phase during
normal playback.
4. Press the STOP button.
1
2
3
4
4
MOTOR SPEED
ADJUSTMENT
c. Adjusting motor speed
1. Insert the test tape (MTT-111 or etc. 3,000 Hz).
2. Press the PLAY button.
3. Use a flat-tip screwdriver to turn the SVR to adjust so
that the frequency counter becomes 3,000 Hz.
4. Press the STOP button.
d. Replacing the motor
e. Checking the mechanism torques
• Clean the head, capstan and pinch roller before making
any measurement.
Measurement Take-up torque Back tension Tape tension
Cassette for PLAY : TW-2111A PLAY : TW-2111A Drive-power cassette
measurement F.FWD/REW : TW-2231 TW-2412
PLAY 30 ~ 70gr.cm 1.0 ~ 6.0gr.cm 80 gr or more
F.FWD/REW 55 gr or more - -
CAUTION :
THIS PRODUCT CONTAINS A LOW
POWER LASER DEVICE,TO ENSURE
CONTINUED SAFETY DO NOT REMOVE
ANY COVERS OR ATTEMPT TO GAIN
ACCESS TO THE INSIDE OF THE
PRODUCT.REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
LASER OUTPUT ..............0.6 mW Max. (CW)
WAVELENGTH ..................790 nm
a. Replacing the head
1. After replacement, demagnetize the heads by using
a degausser.
2. Be sure to clean the heads before attempting to make
any adjustments.
3. Be sure both channels (1 and 2) are the same level.
(Using a dual-channels oscilloscope).
4. All wiring should be returned to the original position
after work is completed.
CD PICK-UP MAINTENANCE
About pick-up (Optical lens) Cleaning
Clean a lens with swab of the cotton which moistened it with alcohol, cleaning paper or cleaning disc appointed.
Specified cleaning disc : LC-1 (Part code : 645 026 1961 ..... manufactured by SANYO.)
Show a clean procedure in the following in reference by swab of cotton.
1. Cotton swab is wrapped with Cleaning paper.
2. Add the isopropyl alcohol.
3. Gently move the tip of cotton swab just like a draw a whirlpool from inside to outside on the surface of lens.
- 2 -
1. FM
Connection
Input Output
IC211 Alignment voltage IC211
3-22pin(TP24,25) 3-22pin is 0.0±0.05V
TP11(H) 87.5MHz L2002 1.00±0.05V
TP12(E). 108.0MHz --- 5.50±0.50V Check Only
2. AM
Connection
Input Output
TP13(L)
TP14(R)
TP15(E)
FM Antenna SG=66dBuV1
2
IF(0V)
Adjustment
Cover
Voltage
---
Step
Step
Adjusting
Circuit
Adjusting
Circuit
Remark
Remark
SG
Frequency
Adjustment
Adjustment
T200298.0MHz
SG
Frequency
T2001
Maximum
2
Cover
Voltage
1.00±0.05V
7.10±0.50V Check Only
522kHz
1710kHzTP12(E)
TP13(L)
TP14(R)
TP15(E)
450kHz
at 999kHz
603kHz
1404kHz
1
IF
Adjustment
Loop Ant
---
TP11(H)
3 Tracking Loop Ant
L2205
---
Maximum
L2204
CT211
E
MW ANT
MW OSC
E
E
E
BAND1
LID_SW
IF
SD
FR_GND
AM OSC
VT
AMPGND
TU_L
TU_R
ST
MONO
MUTE
BAND1
BAND2
VT
1AD4B10D1712D
T002 94V-0
LW OSC
+B 9V
E
E
E
E
L2205
XF212
IC201
XF211
CT211
Q2001
D2005
D2004
D2102
SH201
D2002
D2003
C2009
J2110
L2003
J2109
J2211
C2104
J2209
C2111
C2119
C2121
C2801
C2701
C2106
C2113
C2107
D2101
L2005
Q2101
L2006
J2203
J2206
J2105
C2312
C2108
Q2111
J2307
C2218
J2302
Q2201
J2101
J2205
S2001
J2208
J2304
CN201
L2002
J2306
J2102
J2103
C2112
T2002
IC211
T2001
XF215
D2006
J2303
J2108
U
J2106
L2204
XF210
J2212
L2007
Q2002
Q2003
D2104
CN203
CN202
Q2102
J2107
J2210
J2301
J2104
Q2110
J2300
J2202
J2200
J2201
J2100
J2207
J2204
J2305
R2129
L2001
C2131
C2142
R2131
C2024C2005
C2002
R2001
C2001
C2001
C2014
C2014
C2011
C2011
C2003
C2003
R2008
R2008
C2101
C2101
C2117
C2117
C2122
C2122
C2702
C2702
C2802
C2802
R2106
R2106
R2206
R2206
R2201
R2201
C2115
C2115
R2301
R2301
C2114
C2114
C2022
C2022
R2900
R2900
C2001
R2002
C2014
R2005
C2013
R2004
R2003
C2011
C2012
C2008
C2015
R2014
C2017
C2003
R2006
R2008
R2007
R2009
C2021
R2101
C2101
C2118
C2117
C2120
C2122
C2702
C2802
R2801
R2701
C2103
C2102
R2104
R2106
C2110
C2126
R2113
R2117
R2119
C2209
C2020
C2019
C2311
C2207
R2128
R2127
R2206
R2201
C2027
C2140
C2025
R2126
C2026
C2115
R2301
C2114
R2303
R2302
R2105
C2010
R2205
C2022
C2029
R2901
R2010
R2011
R2210
C2141
R2900
C2902
R2107
L2002 L2205
L2204
TP11
TP24TP25
TP12
TP13
TP14
TP15
T2001
CT211
IC211
T2002
TUNER ADJUSTMENTS
• Use a plastic screw driver for adjustments.
• MODE : ST (Stereo)
• Speaker impedance : 4 ohms
• TUNING
FM : 87.5 - 108MHz
AM :522 - 1710kHz(9kHz steps)
520 - 1710kHz(10kHz steps)
Antenna : 75Ω unbalanced, Modulation : 1 kHz
Dev. : ±22.5kHz(MONO), ±22.5kHz(STEREO),±6.75kHz(PILOT)
RF Level : dBuV EMF
Output Level : about 30mV at TP13, TP14, TP15
Anntena : IRE Loop(SG), Moduration : 1kHz 30%
RF Level : dBuV EMF
Output Level : about 30mV at TP13, TP14, TP15
- 3 -
EXPLODED VIEW (CABINET & CHASSIS)
1
3
2
6
7
10
9
8
Y01
Y02
Y03
Y03
Y04
Y05
Y05
Y07
Y08
Y07
Y06
Y08
Y09
Y10
Y11
Y14
Y15
Y16
Y16
Y17
Y18
Y19
Y12
Y13
11
15
14
13
4
5
12
16
17
18
19
24
25
36
73
27
28
29
32
33
30
31
34
35
26
24
20
21
51
52
55
53
54
56
71
72
74
75
57
76
58
23
22
- 4 -
ELECTRICAL PARTS
REF.NO. PART NO. DESCRIPTION
51 614 326 2770 FLEXIBLE FLAT CABLE,
FRONT TO AMP
or 614 327 0812 FLEXIBLE FLAT CABLE,
FRONT TO AMP
52 614 327 0829 FLEXIBLE FLAT CABLE,
FRONT TO TUNER
or 614 326 2787 FLEXIBLE FLAT CABLE,
FRONT TO TUNER
53 614 309 8454 ASSY,WIRE
or 614 314 4779 ASSY,WIRE
54 614 326 2794 FLEXIBLE FLAT CABLE,CD PICK UP
or 614 327 0836 FLEXIBLE FLAT CABLE,CD PICK UP
55 423 016 7908 FUSE 250V 2.5A
56 614 274 2013 CORD,ID CONNECTOR
57 645 051 8805 TRANS,POWER
58 645 032 1887 CORD,POWER-2.0MK
PARTS LIST
CAUTION : Regular type resistors and capacitors are not listed. To know those values, refer to the schematic diagram.
Regular type resistors are less than 1/4 W carbon type and 0 ohm chip resistors.
Regular type capacitors are less than 50 V and less than 1000 µF type of Ceramic type and Electrical type.
N.S.P : Not available as service parts.
PRODUCT SAFETY NOTICE
EACH PRECAUTION IN THIS MANUAL SHOULD BE FOLLOWED DURING SERVICING. COMPONENTS IDENTIFIED WITH THE
IEC SYMBOL
!
!!
IN THE PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATED COMPONENTS IN WHICH SAFETY AND
PERFORMANCE CAN BE OF SPECIAL SIGNIFICANCE. WHEN REPLACING A COMPONENT IDENTIFIED BY
!
!!
, USE ONLY THE
REPLACEMENT PARTS DESIGNATED, OR PARTS WITH THE SAME RATINGS OF RESISTANCE, WATTAGE OR VOLTAGE THAT
ARE DESIGNATED IN THE PARTS LIST IN THIS MANUAL. LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS MUST BE
MADE TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE
RETURNING THE PRODUCT TO THE CUSTOMER.
PACKING & ACCESSORIES
REF.NO. PART NO. DESCRIPTION
614 326 8345 CARTON CASE
614 325 2818 CUSHION,REAR
614 325 2825 CUSHION,FRONT
614 326 8376 INSTRUCTION MANUAL
645 046 8322 ASSY,ANTENA,LOOP
or 645 005 1227 ASSY,ANTENA,LOOP
614 325 5741 LID,BATTERY,SERVICE
645 057 4559 REMOCON,RB-DA1000
614 326 5962 ASSY,BOX,SPEAKER,SPEAKER(L,R)
CABINET & CHASSIS
REF.NO. PART NO. DESCRIPTION
1 614 325 2665 COVER,DECK
2 614 325 2672 DEC,WINDOW,DECK
3 614 325 2740 LID,CASSETTE
4 614 325 2788 SPRING,DOOR DECK
5 614 325 2603 ASSY,DOOR,DECK
6 614 325 2733 KNOB,VOLUME
7 614 325 2658 CAP,DECORATION
8 614 326 6259 DEC,WINDOW LCD
9 614 326 6334 PANEL,FRONT
10 614 326 6129 ASSY,PANEL,FRONT
11 614 309 7969 ASSY,GEAR,CASSETTE
12 614 326 1971 KNOB,DEC MECHA,REC
13 614 326 2589 KNOB,DEC MECHA,PLAY
14 614 326 2596 KNOB,DEC MECHA,REW
15 614 326 2602 KNOB,DEC MECHA,FFWD
16 614 326 2619 KNOB,DEC MECHA,STOP/EJECT
17 614 326 2626 KNOB,DEC MECHA,PAUSE
18 614 326 2633 MOUNTING,DEC KNOB
19 614 308 0534 SPRING,PLATE,REC
20 614 325 2719 DEC,WINDOW,BUTTON,1 KEY
21 614 325 2634 BUTTON,LEFT,8 KEYS
22 614 325 2702 DEC,WINDOW SENSOR
23 614 325 2627 BUTTON,RIGHT,5 KEYS
24 614 310 3899 SPACER,MECHA,CD+DA11
25 614 307 2072 COVER,PICK-UP
26 614 322 2132 ASSY,GEAR,LID,CD
27 614 325 2764 MOUNTING,CD
28 614 303 0263 LATCH,PUSH,CD DOOR LOCKING
29 614 307 8821 PULLEY
30 614 303 0256 LATCH,MAGNET
31 614 325 2795 SPRING,DOOR CD
32 614 325 2757 LID,CD
33 614 326 8581 DEC,WINDOW,CD
34 614 316 1172 STOPPER
35 614 326 8253 ASSY,CABINET,REAR
36 614 325 6014 ASSY,MECHA,DA11T3CN-SASH
FIXING PARTS
REF.NO. PART NO. DESCRIPTION
Y01 411 020 8905 SCR S-TPG BRZ+FLG 3X10,GEAR
Y02 411 021 3503 SCR S-TPG BIN 3X10,
F-PANEL+MTG DECK KNOB
Y03 411 021 3503 SCR S-TPG BIN 3X10,
PANEL+DECK MECHA
Y04 411 126 1404 SCR S-TPG BIN 2X4,
SPRING DECK REC
Y05 411 021 3503 SCR S-TPG BIN 3X10,
FRONT PWB+MOUNT
Y06 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+CD PCB
Y07 411 021 1806 SCR S-TPG BIN 2.6X10,
MTG CD+MECHA CD
Y08 411 092 0906 WASHER Z 2.6X10X0.5,
MECHA CD+MOUNTING
Y09 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+TUNER PCB
Y10 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+ASSY,GEAR
Y11 411 021 4906 SCR S-TPG BIN 3X20,
PANEL+MOUNTING
Y12 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+AMP PCB
Y13 411 184 0906 SCR S-TPG BIN 2.3X10,
WIN CD+LID CD
Y14 411 020 9100 SCR S-TPG BRZ+FLG 3X12,
REAR+P-TRANS
Y15 411 021 3503 SCR S-TPG BIN 3X10,
REAR+STOPPER
Y16 411 098 7800 SCR S-TPG FLT 3X12,
PANEL+REAR+MOUNTING
Y17 411 021 4500 SCR S-TPG BIN 3X16,PANEL+REAR
Y18 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+REAR
Y19 411 021 3503 SCR S-TPG BIN 3X10,
C-REAR(ANT TERMINAL)
- 5 -
PARTS LIST
REF.NO. PART NO. DESCRIPTION
FRONT P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
71 614 326 8741 ASSY,PWB,FRONT(Only Initial)
BR601 614 325 3730 HOLDER,LCD,HOLDER_LCD
C6200 403 373 7001 NP-ELECT 1U M 50V
or 403 259 0508 NP-ELECT 1U M 50V
CN601 645 059 0474 SOCKET,FPC 14P,FRONT-AMP
CN602 614 016 8464 PLUG,FRONT-LED
CN603 645 059 0481 SOCKET,FPC 15P,FRONT-TU
D6901 407 012 4406 DIODE 1SS133
D6902 407 012 4406 DIODE 1SS133
IC601 409 546 0701 IC LC72338-9B55,MICON
L6900 645 001 4550 INDUCTOR,10U K
L6901 645 002 1459 INDUCTOR,22U K
LCD60 645 057 4542 LCD
LS601 614 309 4180 DEC,SHEET,LCD,DEC_LCD_SHEET
Q6200 405 017 9709 TR 2SC3330-U
or 405 017 9600 TR 2SC3330-T
or 405 011 8609 TR 2SC1740S-S
or 405 011 8500 TR 2SC1740S-R
or 405 143 8706 TR KTC3199-GR
Q6201 405 017 9709 TR 2SC3330-U
or 405 017 9600 TR 2SC3330-T
or 405 011 8609 TR 2SC1740S-S
or 405 011 8500 TR 2SC1740S-R
or 405 143 8706 TR KTC3199-GR
S6001 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6002 614 220 5471 SWITCH,TACT
or 614 240 1002 SWITCH,TACT
or 645 006 5958 SWITCH,PUSH 1P-1T
or 645 048 3820 SWITCH,PUSH
S6003 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6004 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6005 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6006 645 006 5958 SWITCH,PUSH 1P-1T
or 645 048 3820 SWITCH,PUSH
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6007 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6008 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6009 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6010 614 220 5471 SWITCH,TACT
or 614 240 1002 SWITCH,TACT
or 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
S6011 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6012 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6013 645 048 3820 SWITCH,PUSH
or 645 006 5958 SWITCH,PUSH 1P-1T
or 614 240 1002 SWITCH,TACT
or 614 220 5471 SWITCH,TACT
S6500 645 057 4535 SWITCH,ROTARY(ENCODER)
SE601 407 220 6803 PHOTO DIODE SPS-444-1-G1
X6001 645 052 6206 OSC,CRYSTAL 4.5MHZ
LED P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
72 614 325 4751 ASSY,PWB,LED(Only Initial)
D6951 408 049 3707 LED SLP-3G118C51HAB-T1,LED
D6952 408 049 3707 LED SLP-3G118C51HAB-T1,LED
D6953 408 049 3707 LED SLP-3G118C51HAB-T1,LED
D6954 408 049 3707 LED SLP-3G118C51HAB-T1,LED
D6955 408 049 3707 LED SLP-3G118C51HAB-T1,LED
CD P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
73 614 327 5077 ASSY,PWB,CD(Only Initial)
CN111 645 059 0498 SOCKET,FPC 16P
CN113 645 005 8127 PLUG,6P
or 614 310 2472 PLUG,6P
CN122 614 310 2496 PLUG,8P
or 645 005 8134 PLUG,8P
D1401 407 012 4406 DIODE 1SS133
D1402 407 012 4406 DIODE 1SS133
D1403 407 012 4406 DIODE 1SS133
D1404 407 099 5204 ZENER DIODE MTZJ5.1B
D1410 407 098 3300 DIODE RL153-BF-S2
IC101 409 503 5701 IC LA9242M-MPB
IC102 409 539 9704 IC LC78629E
IC103 409 486 8706 IC MM1469XH
L1451 645 001 4550 INDUCTOR,10U K
PR140 645 014 2499 PROTECTOR,0.4A 125V
Q1301 405 008 6809 TR 2SB808-F-SPA
or 405 008 7202 TR 2SB810-E
or 405 008 7301 TR 2SB810-F
Q1401 405 141 3604 TR KTA1273-Y
or 405 009 5207 TR 2SB927-S
or 405 009 5306 TR 2SB927-T
X1451 614 231 2667 RESONATOR
or 645 057 1145 OSC,CERAMIC 16.93MHZ
TUNER P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
74 614 326 6822 ASSY,PWB,TUNER(Only Initial)
CN201 645 038 7715 TERMINAL
or 645 025 4703 TERMINAL,ANTENNA
CN202 645 059 0481 SOCKET,FPC 15P
CN203 614 221 8273 TERMINAL
CT211 645 032 5663 TRIMMER,7PF
D2002 407 157 8109 VARACTOR DI SVC211-B
D2003 407 157 8109 VARACTOR DI SVC211-B
D2004 407 012 4406 DIODE 1SS133
D2005 407 012 4406 DIODE 1SS133
D2006 407 012 4406 DIODE 1SS133
D2101 407 012 4406 DIODE 1SS133
D2102 407 105 1305 VARACTOR DI SVC342L-V
or 407 105 1602 VARACTOR DI SVC342M-V
D2104 407 099 5303 ZENER DIODE MTZJ5.6B
IC201 409 016 0200 IC LA1186N-AUDIO
IC211 409 474 3201 IC LA1844ML
L2001 645 040 2753 INDUCTOR,AIR —
L2002 645 040 2746 COIL,AIR —
L2003 645 002 1534 INDUCTOR,8.2U K
L2005 645 002 1459 INDUCTOR,22U K
L2006 645 002 1459 INDUCTOR,22U K
L2007 645 002 1459 INDUCTOR,22U K
- 6 -
AMPLIFIER P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
75 614 327 5060 ASSY,PWB,AMP(Only Initial)
C4714 403 058 4608 POLYESTER 0.15U J 50V
or 403 377 6406 POLYESTER 0.15U J 50V
C4814 403 058 4608 POLYESTER 0.15U J 50V
or 403 377 6406 POLYESTER 0.15U J 50V
C4913 403 329 5907 ELECT 3300U M 25V
or 403 350 9301 ELECT 3300U M 25V
C4918 403 056 7502 POLYESTER 1000P J 50V
or 403 377 6307 POLYESTER 1000P J 50V
CN401 645 006 1875 PLUG,2P,SPEAKER
CN402 645 006 1875 PLUG,2P,SPEAKER
CN405 614 310 2755 PLUG,4P
or 645 004 2904 PLUG,4P
CN406 614 310 2458 PLUG,4P
or 645 005 8110 PLUG,4P
CN421 645 011 6384 JACK,PHONE D3.6,HEADPHONE
or 645 055 1017 JACK,PHONE D3.6,HEADPHONE
CN441 614 310 2731 PLUG,2P,POWER
or 645 004 2881 PLUG,2P,POWER
CN490 645 012 2736 SOCKET,DIP 8P
CN491 645 059 0474 SOCKET,FPC 14P
CN492 614 309 8812 ASSY,WIRE
or 614 314 4809 ASSY,WIRE
D4102 407 012 4406 DIODE 1SS133
D4951 407 099 6003 ZENER DIODE MTZJ9.1B
D4953 407 012 4406 DIODE 1SS133
D4961 407 012 4406 DIODE 1SS133
D4962 407 012 4406 DIODE 1SS133
D4963 407 012 4406 DIODE 1SS133
D4980 407 098 3300 DIODE RL153-BF-S2
D4981 407 098 3300 DIODE RL153-BF-S2
D4982 407 098 3300 DIODE RL153-BF-S2
D4983 407 098 3300 DIODE RL153-BF-S2
D4993 407 012 4406 DIODE 1SS133
FCL41 645 006 4760 HOLDER,FUSE
or 645 031 7903 HOLDER,FUSE
FCL42 645 006 4760 HOLDER,FUSE
or 645 031 7903 HOLDER,FUSE
HS401 614 307 9866 HEAT SINK
IC410 409 384 3506 IC BA3314F
IC411 409 390 1107 IC LC75392
IC412 409 295 7402 IC TA8229K
IC446 409 039 9204 IC NJM78L05A
L4780 645 002 1459 INDUCTOR,22U K
L4781 645 002 1459 INDUCTOR,22U K
L4881 645 002 1459 INDUCTOR,22U K
L4902 645 031 5893 TRANS,OSC,85KHZ,O.S.C
LG401 645 006 4432 FIXER
PR495 645 014 2529 PROTECTOR,1.25A 125V
PR496 645 014 2536 PROTECTOR,1.5A 125V
Q4103 405 000 0508 TR DTA114ES
or 405 110 5400 TR KRA102M-A
Q4104 405 000 3103 TR DTC114ES
or 405 109 9204 TR KRC102M-A
Q4106 405 000 3103 TR DTC114ES
or 405 109 9204 TR KRC102M-A
Q4108 405 000 3806 TR DTC114YS
or 405 143 0007 TR KRC107M
Q4109 405 000 3806 TR DTC114YS
or 405 143 0007 TR KRC107M
Q4730 405 006 1806 TR 2SA933S-R
or 405 006 1905 TR 2SA933S-S
or 405 004 5103 TR 2SA608-G-SPA
or 405 004 4601 TR 2SA608-F-SPA
or 405 143 6504 TR KTA1267-GR
Q4740 405 000 3103 TR DTC114ES
or 405 109 9204 TR KRC102M-A
Q4751 405 151 4400 TR KTD1303
or 405 021 0204 TR 2SD1012-F-SPA
or 405 021 0600 TR 2SD1012-G-SPA
or 405 033 6706 TR 2SD1468S-R
or 405 033 6805 TR 2SD1468S-S
Q4830 405 143 6504 TR KTA1267-GR
or 405 004 4601 TR 2SA608-F-SPA
or 405 004 5103 TR 2SA608-G-SPA
or 405 006 1806 TR 2SA933S-R
or 405 006 1905 TR 2SA933S-S
Q4840 405 000 3103 TR DTC114ES
or 405 109 9204 TR KRC102M-A
Q4851 405 151 4400 TR KTD1303
or 405 021 0204 TR 2SD1012-F-SPA
or 405 021 0600 TR 2SD1012-G-SPA
or 405 033 6706 TR 2SD1468S-R
or 405 033 6805 TR 2SD1468S-S
Q4902 405 011 8500 TR 2SC1740S-R
or 405 017 9600 TR 2SC3330-T
or 405 017 9709 TR 2SC3330-U
or 405 011 8609 TR 2SC1740S-S
or 405 143 8706 TR KTC3199-GR
Q4903 405 143 8706 TR KTC3199-GR
or 405 011 8500 TR 2SC1740S-R
or 405 011 8609 TR 2SC1740S-S
or 405 017 9600 TR 2SC3330-T
or 405 017 9709 TR 2SC3330-U
Q4904 405 143 8706 TR KTC3199-GR
or 405 011 8500 TR 2SC1740S-R
or 405 011 8609 TR 2SC1740S-S
or 405 017 9600 TR 2SC3330-T
or 405 017 9709 TR 2SC3330-U
Q4951 405 138 6403 TR KTD2058Y
or 405 095 1602 TR 2SD2061-E
or 405 095 1701 TR 2SD2061-F
Q4992 405 141 3703 TR KTA1271-Y
or 405 008 2405 TR 2SB698-F
or 405 008 2504 TR 2SB698-G
Q4994 405 143 0007 TR KRC107M
or 405 000 3806 TR DTC114YS
PARTS LIST
REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. DESCRIPTION
L2204 645 037 2377 TRANS,ANT,796KHZ
L2205 645 040 2739 TRANS,OSC,796KHZ
Q2001 405 151 4301 TR KTC3195-Y
or 405 151 4806 TR KTC3195-O
Q2002 405 151 4301 TR KTC3195-Y
or 405 151 4806 TR KTC3195-O
Q2003 405 011 8609 TR 2SC1740S-S
or 405 011 8500 TR 2SC1740S-R
or 405 143 8706 TR KTC3199-GR
or 405 017 9600 TR 2SC3330-T
or 405 017 9709 TR 2SC3330-U
Q2101 405 151 5209 TR KRA107M
or 405 000 0904 TR DTA114YS
Q2102 405 143 0007 TR KRC107M
or 405 000 3806 TR DTC114YS
Q2110 405 143 0007 TR KRC107M
or 405 000 3806 TR DTC114YS
Q2111 405 151 4301 TR KTC3195-Y
or 405 151 4806 TR KTC3195-O
Q2201 405 151 5209 TR KRA107M
or 405 000 0904 TR DTA114YS
S2001 645 023 5795 SWITCH,LEVER
SH201 614 256 3052 SHIELD
T2001 645 043 0213 FILTER,450KHZ
T2002 645 040 9981 TRANS,IF 10.7MHZ
or 645 039 9923 TRANS,IF 10.7MHZ
XF210 645 059 0047 FILTER,BP
XF211 645 054 1223 CERAMIC FILTER 10.70MHZ
or 645 010 7665 CERAMIC FILTER 10.70MHZ
or 614 240 2917 FILTER,CERAM
XF212 645 010 7665 CERAMIC FILTER 10.70MHZ
or 614 240 2917 FILTER,CERAM
or 645 054 1223 CERAMIC FILTER 10.70MHZ
XF215 645 059 0054 CERAMIC FILTER 450KHZ
- 7 -
Q4995 405 141 3703 TR KTA1271-Y
or 405 008 2405 TR 2SB698-F
or 405 008 2504 TR 2SB698-G
R4752 402 071 1304 FUSIBLE RES 2.2 JA 1/4W
R4852 402 071 1304 FUSIBLE RES 2.2 JA 1/4W
R4941 402 081 0205 FUSIBLE RES 27 JA 1/4W
S4950 645 038 7586 SWITCH,PUSH,R/PSW
SA401 411 021 6405 SCR S-TPG BIN 3X8
SA402 411 021 6405 SCR S-TPG BIN 3X8
POWER TRANSFORMER P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
76 614 325 4744 ASSY,PWB,PT(Only Initial)
CN450 614 020 1215 SOCKET,2P
CN451 614 017 8203 TERMINAL BOARD
CN452 614 017 8203 TERMINAL BOARD
CN453 614 314 4762 ASSY,WIRE
or 614 309 8447 ASSY,WIRE
L4591 645 041 3087 INDUCTOR,180U
or 645 038 6053 INDUCTOR,181U
TM06
TM05
TM04
TM03
TM02
TM01
*
*
*
*
*
EXPLODED VIEW & PARTS LIST (TAPE MECHANISM)
* N.S.P : Not supplied as service parts.
REF.NO. PART NO. DESCRIPTION
PARTS LIST
TAPE MECHANISM
REF.NO. PART NO. DESCRIPTION
614 309 7976 ASSY,MECHA,TM-DA70TN-SH
TM01 645 033 8625 E HEAD 6PA
TM02 645 041 3025 R.P HEAD
TM03 645 009 1612 PINCH ROLLER ARM ASSY
TM04 645 009 1766 RF BELT
TM05 645 033 3415 MAIN BELT
TM06 614 312 0629 ASSY,MOTOR,FOR SERVICE
- 8 -
IC BLOCK DIAGRAM & DESCRIPTION
28 27 26 25 24 23 22 21 20 19 18 17 16 15
1234567 891011121314
Vcc
Vcc
DRIVER MUTE
D.BUFD.BUFD.BUFD.BUF
D.BUFD.BUFD.BUFD.BUF
Level shift
Level shift
Level shift
Level shift
T. S. D
IC103 MM1469XH (CD Driver)
FSS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
47
46
45
44
43
41
40
39
38
37
36
35
34
33
42
32313029282726252423222120191817
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Vcc1 LDS LDD BH1 PH1 LF2 VR REF1 Vcc2
DRF CE
DAT CL CLK DEF
NC
TBC
FSC
DGND
SLI
SLC
RFS-
RFSM
CV+
CV-
SLOF
HFL
TES
TOFF
TGL
JP+
JP-SL+SL-SLDSLEQSPDSP-SPGSPI
SP
AGND
FE-FE
FA-FAFD-
FD
TO
JP
TD
TD-
TA
TH
SCH
TESI
TE
TE-
TB
F
E
FIN1
FIN2
APC
RF DET
REF
VCA
I/V
BAL
VCA
INTER FACE
SLC
RF Amp
TE
T.SERVO & T.LOGIC
F.SERVO & F.LOGICK
SPINDLE SERVO
SLED SERVO
IC101 LA9242M-MPB ( Servo Processing for a CD Player)
- 9 -
IC BLOCK DIAGRAM & DESCRIPTION
Vref BUFFER
RF MIX REG OSC
RF IN GND IF OUT Vcc
1 2 3 4 5 6 7 8 9
IC201 LA1186N-AUDIO (FM Front End)
IC410 BA3314F (Dual Preamplifier with ALC Detector)
14
13
12
11
10
1
2
3
4
5
6
7
NF1
IN1
GND (SUB)
GND
Vcc
IN2
FILTER
ALC
ALC
NC
NC
NC
OUT 1
OUT 2
NF2
150k
150k
+
+
-
-
9
8
FM
IF
FM
DET
LEVEL
DET
S-CURVE
AM/FM
IF
BUFF
REG
GND
COMP
TUNING
DRIVE
AM
IF
AM
DET
VCC
AGC
PILOT
CANCEL
PILOT
DET
DECODER
ANTI-BIRDIE
STEREO
SW
FF
38k
FF
19k
VCO
304kHz
AM
RF.AMP
AM
MIX
AM
OSC
ALC
BUFF
P-DET
FF
19k
2
1
23456789101112
24 23 22 21 20 19 18 17 16 15 14
13
IC211 LA1844ML ( Tuner System)
- 10 -
IC BLOCK DIAGRAM & DESCRIPTION
IC601 IC LC72338-9B55 (Single-Chip PLL + Controller)
68
66
67
65
19
20
21
22
64
63
62
61
23
24
25
26
27
29
30
28
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
59
60
56
57
58
78
77 E01
E02
COM1
COM2
COM3
Vdd2
Vdd1
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S15
S12
S13
S14
S16
S17/PE0
S18/PE1/SCK2
S19/PE2/SO2
S20/PE3/SI2
S21/PF0
S22/PF1/SCK1
S23/PF2/SO1
S24/PF3/SI1
S28/PM3
S25/PM0
S26/PM1
S27/PM2
S29/PN0/BEEP
S31/PN2
S30/PN1
S32/PN3
PJ3/DAC3
PJ2/DAC2
PJ1/DAC1
PJ0/DAC0
PK3
PK2
PK1/INT1
PK0/INT0
PH3/ADI3
PH2/ADI2
PH1/ADI1
PH0/ADI0
1
80
74
XIN
XOUT
FMIN
75
72
73
76
70
71
AMIN
SNS
HOLD
VDD
VSS
HCTR
LCTR
69
79
2
18
17
16
15
14
13
12
11
10
9
8
7
TEST1
TEST2
PA 0
PA 1
PA 2
PA 3
PB0
PB1
PB2
PB3
PC0
PC1
PC2
PC3
6
5
4
3
PG0
SCK0/PG1
SO0/PG2
SI0/PG3
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
SIO
BUS
DRIV.
1 / 2
V-DET
SNSFF
1 / 16,1 / 17
PROGRAMMABLE DIVIDER
LATCH
UNIVERSAL
COUNTER
(20bits)
RAM
512 x 4bits
ROM
8K x 16bits
ADDRESS
DECODER
BUS
DRIVER
INSTRUC-
TION
DECODER
ADDRESS DECODER
PROGRAM COUNTER
STACK
JUDGE
ALU
DAC
ADC
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
LATCH
BUS
DRIV.
MPX
INTERRUPT
MPX
MPX
MPX
MPX
MPX
BEEP
LCPA/B
LCDA/B
SEG
PLA
LATCH
LCD
PORT
DRIVER
96
4
4
7
SELECTER
PHASE
DETECTOR
UNLOCK
F/F
COMMON
DRIVER
REFERENCE DIVIDERDIVIDER
XIN
TEST2
SI0/PG3
SO0/PG2
SCK0/PG1
PG0
PC3
PC2
PC1
PC0
PB3
PB2
PB1
PB0
PA 3
PA 2
PA 1
PA 0
PK3
PK2
INT1/PK1
INT0/PK0
PN3/S32
PN2/S31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
P10/DAC0
P11/DAC1
P12/DAC2
P13/DAC3
Vdd1
Vdd2
COM1
COM2
COM3
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
PN1/S30
BEEP/PN0/S29
PM3/S28
PM2/S27
PM1/S26
PM0/S25
[Vpp]Vdd
SI1/PF3/S24
SO1/PF2/S23
SCK1/PF1/S22
PF0/S21
SI2/PE3/S20
SO2/PE2/S19
SCK2/PE1/S18
PE0/S17
S16
XOUT
TEST1
E02
E01
VSS
AMIN
FMIN
Vdd
SNS
LCTR
HCTR
HOLD
PH0/ADI0
PH1/ADI1
PH2/ADI2
PH3/ADI3
- 11 -
IC BLOCK DIAGRAM & DESCRIPTION
IC601 IC LC72338-9B55 (Single-Chip PLL + Controller)
PIn name Pin No. I/O I/O Format Functions
PA 0
PA 1
PA 2
PA 3
18
17
16
15
I
Pull-down
resistor
input
Port only for key return signal input.
The threshold voltage is set to a relatively low value.
When a key matrix is formed by combining PB and PC ports,
maximum three simultaneous key presses can be detected.
All of four pull-down resistor are set by the IOS instruction with
Pn=2, bl and specification of resistor for each pin is impossible.
The input is disabled in clock stop mode.
PB0
PB1
PB2
PB3
PC0
PC1
PC2
PC3
14
13
12
11
10
9
8
7
O
Unbalance
CMOS
Push-pull
Port only for key source signal output.
Since the output transistor circuit is an unbalanced CMOS
structure, diodes to prevent short-circuiting due to multiple key
presses are not required.
In clock stop mode, these pins go to the output high-impedance
state and hold this state until an output instruction is executed.
PG0
PG1/SCK0
PG2/SO0
PG3/SI0
6
5
4
3
I/O
CMOS
posh-pull
General-purpose output/serial I/O ports. Schmidt type input
the IOS instruction performs switching between general-purpose
I/O ports and serial I/O ports, and between input and output for
general-purpose I/O ports.
• When used as general-purpose I/O ports these pins
can be set for input or output in bit units(bit I/O),
and are set for use as general-purpose I/O ports by
the IOS instruction with Pn=0.
b0=SI/O 0 0 • • • general-purpose port
1 • • • SI/O port
Specification of input or output is made by the IOS instruction
in bit units.
PG • • • Pn=6 0 • • • Input
1 • • • Output
• When used as serial I/O ports these pins are set for
serial I/O port use by the IOS instruction with Pn=0.
The content of serial I/O data buffer is saved or load by the
INR and OUTR instructions.
*Pin setup states when used as serial I/O ports
PG0 • • • general-purpose input or output
PG1 • • • SCK0 output in internal block
SCK0 input in external block
PG2 • • • SO0 output
PG3 • • • SI0 input
In clock stop mode, input is disabled and these pins go to
the high-impedance state.
During the power-on reset, these pins become general-purpose
input ports.
4.5MHz crystal oscillator pin.
XIN
XOUT
1
80
EO1
EO2
78
77
O
CMOS
tristate
-
I
O
Charge pump output pin.
These pins go to high-impedance state when the HOLD pin is set
low in the hold enable state.
In ckock stop mode, during the power-on reset and in the PLL
stop state, these pins go to the high-impedance state.
VSS
VDD
FMIN
AMIN
HCTR
76
31,73
74
75
70
72
-
I
I
I
I
-Power supply pin.
FMVCO (local oscillator) input pin.
This pin is selected by the PLL instruction CW1 (b1=0,b0=don't
care). Capacitor coupling must be used for signalinput. Input is
disabled when the HOLD pin is set low inthe hold enable state.
Input is disable in clock stop mode,during the power-on reset,
and in the PLL stop state.
AMVCo (lcal oscillator) input pin.
This pin is selected and the band set by the PLL instruction
CW1 (b1,b0).
Capacitor coupling must be used for signal input.
Input is disabled when the HOLD pin is set low in the hold enable
state. Input is disabled in clock stop mode, during the power-on
reset, and in the PLL stop state.
b1 b0 Band
1 0 2 to 40MHz (SW)
1 1 0.5 to 10MHz (MW,NW)
Universal counter / general-purpose input port.
The IOS instruction b3 with Pn=3 switches the pin function
between universal counter input and general-purpose input.
• Frequency measurement
The universal counter function is selected by an IOS
instruction with Pn=3 and b2=0. HCTR frequency measure-
ment mode is set up by a UCS instruction with b3=0 and b2=0,
and counting is started with a UCC instruction after the count
time is selected. The CNTEND flag is set when the count
completes. To operate this circuit as an AC amplifier in this
mode, the input must be capacitor coupled.
• For use as the general-purpose input pin.
The general-porpose input port function is selected by an IOS
instruction with Pn=3 and b2=1. An internal register (address
OEH) input instruction INR(b0) is used to acquire data from
this pin.
Input is disabled in clock stop mede (the input pin will be pulled
down.) During the power-on reset, the universal counter function
is selected.
SNS
Voltage sense / general-purpose input pin port.
This circuit is designed for a relatively low input threshold voltage.
• For use as the voltage sense pin
This input pin is is used to determine whether or not a power
failure occurred after recovery from backup (clock stop) mode.
An internal sense F/F is used for this determination. The
sense F/F is tested with a TUL instruction (b2).
• For use as the general-purpose input port
When used as a genaral-purpose input port, the state is
sensed by using a TUL instruction (b3).
Since unlike other input ports, input is not disablle in clock
stop mode and during the power-on reset, special care is
required with respect to through currents.
PIn name Pin No. I/O I/O Format Functions
LCTR
PH0/ADI0
PH1/ADI1
PH2/ADI2
PH3/ADI3
71
68
67
66
65
69
I
I
I
Universal counter (freqency and period measurement) / general-
purose input port.
This IOS instruction b3 with Pn=3 swithes the pin function
between universal counter input and general-puropse input.
• Frequency measurement
The universal counter function is selected by an IOS
instruction with Pn=3 and b3=0. LCTR frequency measure-
ment mode is set up by a UCS instruction with b3=0 and b2=1,
and counting is started with a UCC instruction after the count
time is selected. The CNTEND flag is set when the count
completes. To operate this circuit as an AC amplifier in this
mode, the input must be capacitor coupled.
• Period measurement
With the universal counter function selected, a UCS instruction
with b3=1 and b2=0 sets up the period measurement mode
and a UCC instruction starts counting after selecting the
count time. The CNTEND flag is set when the count
completes. In this mode, the signal must be input with DC
coupling to turn off the bias feedback resistor.
• For use as general-purpose input pin use.
The general-purpose input port function is selected by an IOS
instruction with Pn=3 and b3=1. An internal register (address
OEH) input instruction INR(b1) is used to acquire data from
this pin. Input is disabled in clock stop mode. (The input pin
will be pulled down.) During the power-on reset. The universal
counter function(in HCTR frequency measurement mode) is
selected.
HOLD
PLLcontrol and CLOCK STOP mode control pin.
Setting this pin low in the hold enable state disables input to the
FMIN and AMIN pins and sets the E0 pin to the high-impedance
state. To enter clocl stop mode, set the HOLDEN flag, set this pin
low, and execute a CKSTP instruction. To clear clock stop mode
set this pin high.
General-purpose input ports/ADC input pins.
The IOS instruction with Pn=7 switches the pin function between
genetal-purpose input ports and ADC inputs.
• For use as the general-purpose input port
The IOS instruction with Pn=7 specifies the use as general-
purpose input port in bit units.
• For use as ADC input pin
The IOS instruction with Pn=7 specifies the use as ADC in bit
units. The IOS instruction with Pn=1 specifies the pin to
convert. The UCC instruction (b2) starts a conversion.
The ADCE flag will be set when the conversion completes.
Note) Executing an input instruction for a port specified for ADI
use will always return low since input is disabled. These
pins must be set up for general-purpose input port usage
before an input instruction is excuted. (In other words, the
port must be set to the general-porpose input function
before the input instruction is executed.)
Input is disabled in clock stop mode. During the power-on reset
these pins go to the general-purpose input port function.
PJ0/DAC0
PJ1/DAC1
PJ2/DAC2
PJ3/DAC3
PK0/INT0
PK1/INT1
PK2
PK3
Vdd1
Vdd2
TEST1
TEST2
COM1
COM2
COM3
S1
|
S16
64
63
62
61
22
21
20
19
57
58
79
2
58
57
56
55
|
40
O
I/O
O
O
General-purpose output ports/DAC input pin.
The IOS instruction with Pn=9 switches the pin function between
general-purpose output ports and ADC inputs. Since these pins
are open drain circuit, pull-up resistors are required in exrernal
circuit accepting these outputs.
• For use as general-purpose output port
The IOS instruction with Pn=9F specifies general-purrpose
input port use in bit units.
• For use as DAC
The IOS instruction Pn=9 is used to switch the port in bit units.
DAC data is loaded into tne DAC (0 to 3) specified with the
DAC instruction, Although PWM waveform is output as soon
as the port is switched, the data prior to that load is output for
up to 114µs (1/8.791kHz) after data is loaded.
The general-purpose output port function is selected after a power
-on reset, and the output go to the transistor off (H output) state.
General-purpose I/O / external interrupt ports
There is no instruction that switches the function between general-
purpose ports and external interrupt ports. These pins function for
input only when the external interrupt enable flag is set.
(Output disables)
• For use as general-purpose I/O port
These pins can be set for input or output in bit units (bit I/O).
The IOS instruction is used to specify input or output in bit
units.
• For use as external interrupt pin
This function can be used by setting the external interrupt
enable flags (INT0EN and INT1EN) in status register 2.
The corresponding pin is automatically set to the input port.
To enable interrupt operation, the interrupt enable flag (INTEN)
in status register 1 must also be set. The IOS instruction with
Pn=3, b1=INT1, and b0=INT0 is used to select rising or falling
edge detection.
In clock stop mode, input is disabled and these pins go to the high-
impedance state. During the power-on reset, these pins go to the
general-purpose input port function.
Nch
open drain
CMOS
push-pull
CMOS
three
value
output
CMOS
three
value
output
Pin for external application of 2/3 voltage of LCD drive bias.
Pin for external application of 1/3 voltage of LCD drive bias.
LSI test pin.
These pins must be either left open or connected to ground.
LCD driver common output pin.
Driver format 1/3 duty, 1/3 bias.
This pin is fixed at the low level in CLOCK STOP mode.
This pin is fixed at the low level after a power-on reset.
LCD driver common output pin.
Driver format 1/3 duty, 1/3 bias.
The frame frequency 100MHz.
This pin is fixed at the low level in CLOCK STOP mode.
This pin is fixed at the low level after a power-on reset.
- 12 -
IC BLOCK DIAGRAM & DESCRIPTION
IC601 IC LC72338-9B55 (Single-Chip PLL + Controller)
PIn name Pin No. I/O I/O Format Functions
S17/PE0
S18/PE1/SCK2
S19/PE2/SO2
S20/PE3/SI2
S25/PM0
S26/PM1
S27/PM2
S28/PM3
39
38
37
36
30
29
28
27
I/O
I/O
LCD driver segment output, general-porpose input/output and
serial I/O ports
The IOS instruction is used to switch between the LCD driver
segment output, general-purpose I/O, and serial I/O functions,
and to switch between input and output of the general-purpose
input port function.
• For use as segment output
These pins can be set in bit units.
The IOS instruction with Pn=ODH specifies segment output
use in bit units.
b0=S17/PE0 0 • • • Segment output
b1=S18/PE1 1 • • • PE0 to 3 output
b2=S19/PE2
b3=S20/PE3
• For use as general-purpose input /output port
These pins can be set for input /output in bit units.
(1 bit I/O)
b2=SI/O2 0 • • • Genetal-purpose port
1 • • • SI/O port
Input /output is specified with the IOS instruction in bit units.
PE • • • Pn=4 0 • • • Input
1 • • • Output
• For serial I/O port
The serial I/O port function is specified with the IOS instruction
(Pn=0).
The contents of the serial I/O data buffer can be saved and
loaded with the INR and OUTR instructions.
*Pin setup states when used as a serial I/O port
PE0 • • • General-purpose input /output
PE1 • • • SCK2 output in internal clock mode
SCK2 output in external clock mode
PE2 • • • SO2 output
PE3 • • • SI2 input
In CLOCK STOP mode, if this port is used as a general-purpose
I/O port or as a serial I/O port, the pins go to the input disabled
high-impedance state. If used for segment output, the pins fixed at
the low level. The segment output port function is selected after a
power-on reset.
LCD driver segment output, general-porpose input /output ports.
The IOS instruction is used to switch between the LCD driver
segment output, general-purpose I/O port, and serial I/O to switch
between input and output of the general-purpose input /output
port function.
• For use as segment output
These pins can be set in 4 bits units. The IOS instruction with
Pn=OEH specifies segment output use in bit units.
b0=S25 to 28/PM0 to 3 0 • • • Segment output
1 • • • PM0 to 3
• For use as general-purpose input /output port
These pins can be set for input /output in bit units.
Input /output is specified with the IOS instruction in bit units.
PM • • • Pn=OCH 0 • • • Input
1 • • • Output
In CLOCK STOP mode, if this port is used as a general-purpose
I/O port, the pins go to the input disabled high-impedance state. If
used for segment output, the pins are fixed at the low level. The
segment output port function is selected after a power-on reset.
CMOS
three
value
output
and
push-pull
CMOS
three
value
output
and
push-pull
PIn name Pin No. I/O I/O Format Functions
S21/PF0
S22/PF1/SCK1
S23/PF2/SO1
S24/PF3/SI1
S29/PN0/BEEP
S30/PN1
S31/PN2
S32/PN3
35
34
33
32
26
25
24
23
I/O
O
LCD driver segment output, general-porpose input/output and
serial I/O ports.
The PF0 to 3 inputs are in the Schmidt format.
The IOS instruction is used to switch between the LCD driver
segment output, general-purpose I/O, and serial I/O functions, and
to switch between input and output of the general-purpose input
port function.
• For use as segment output
These pins can be set in 4 bits units. The IOS instruction with
Pn=OEH specifies segment output use in bit units.
b0=S21 to 24/ PF0 to 3 0 • • • Segment output
1 • • • PE0 to 3
• For use as general-purpose input /output port
These pins can be set to input /output in bit units. (1 bit I/O)
b1=SI/O 1 0 • • • Genetal-purpose port
1 • • • SI/O port
Input /output is specified with the IOS instruction in bit units.
PF • • • Pn=5 0 • • • Input
1 • • • Output
• For use as serial I/O port
The serial I/O port function is specified with the IOS instruction
(Pn=0). The contents of the serial I/O data buffer can be saved
and loaded with the INR and OUTR instructions.
*Pin setup states when used as a serial I/O port
PF0 • • • General-purpose input /output
PF1 • • • SCK1 output in internal clock mode
SCK1 output in external clock mode
PF2 • • • SO1 output
PF3 • • • SI1 input
In CLOCK STOP mode, if this port is used as a general-purpose
I/O port or as a serial I/O port, the pins go to the input disabled
high-impedance state. If used for segment output, the pins are
fixed at the low level. The segment output port function is selected
after a power-on reset.
Segment output/general-porpose input port 1/ BEEP tone output
pins. The IOS instruction is used to switch between the segment
output port and the PN0 to 3 functions. The BEEP instruction
switches between the general-purpose output port and BEEP tone
function.
• For use as segment output
These pins can be set in 3 bits units. The IOS instruction with
Pn=OEH specifies segment output use in bit units.
b2=S29 to 32/ PN0 to 3 0 • • • Segment output
1 • • • PN0 to 3
• For use as general-purpose output.
The general-porpose output port function is selected with the
BEEP instruction (b3=0).
PN1 to 3 are dedicated general-purpose output function pins.
• For use as BEEP output pin
The BEEP instruction with b3=1 sets the BEEP output.
The BEEP instruction bit b0,b1 and b2 sets the frequency.
When this is set as the BEEP port, executing an output
instruction will rewrite the internal latch data but has no
influence on the output.
These pins go to the output high-impedance state in clock stop
mode. If used for segment output, the pins are fixed at the low level.
These pins go to the output high-impedance state during the
power-on reset and hold that state until an output instruction is
executed.
CMOS
three
value
output
and
push-pull
CMOS
three
value
output
and
push-pull
9
10
18
11
12
L1
(R1)
LT1
(RT1)
LT2
(RT2)
LT3
(R
T3)
LT4
(RT4)
LTOUT
(RTOUT)
LVROUT
(RVROUT)
LTCO M
(RTCOM)
LVRIN
(RVRIN)
L2
(R2)
L3
(R3)
L4
(R4)
Vref
CL
DI
CE
CONTROL
SHIFT REGISTER
DECODER
LATCH
V
DD
V
SS
2,29
3,28
5,26
7,2
8,2
14
15
16
6,25
4,27
1,30
17
13
IC411 LC75392 (Function & Electric Volume)
IC412 TA8229K (Power Amplifier)
5
7
6
48
14 15
11
10
9
VCC1VCC2
IN-1
IN-2
NF1
NF2
RIPPLE
TERMINAL
B.S.1
B.S.2
OUT-1
OUT-2
POWER
GND
Ch-1
-
+
3
2
12
13
Ch-2
-
+
PRE
GND1
PRE
GND2
BIAS CIRCUIT
THERMAL CUT-OFF
PROTECTION
- 13 -
LCD DISPLAY DESCRIPTION
N
FF
FF
PAD NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
IC NO.
C1
C2
C3
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
COM1
COM1
--
--
7A
7B
ON
6A
6B
OFF
T1
5
T5
4A
4B
4M
3A
3B
3M
T2
T9
T8
2A
2B
2h
1A
1B
1h
SURR
COM2
--
COM2
--
7F
7G
7C
6F
6G
6C
MHZ
PROG.
T6
4F
4G
4C
3F
3G
3C
T4
T3
4h
2F
2G
2C
1F
1G
1C
SLEEP
COM3
--
--
COM3
7E
7D
CH
6E
6D
TR
kHZ
BASS
ST
4E
4D
4K
3E
3D
3K
T7
--
3h
2E
2D
MONO
1E
1D
1K
AM
A
G
BF
D
CE
K
28 1
3h
4h
1h
12
345
67
2h
3h
A
G
BF
D
CE
4h
1h
T1
T8
T2
T4T6
T3T5
T7
T9
LCD60
- 15 -- 14 -
TU_+B
STEREO
TU_GND
SD
TU_R
BAND2
TU_L
BAND1
TU_MUTE
MONO
VT
GND
AMOSC
LID_SW.
AMIF
+B_8.5V
GND
GND
+B_8.5V
AUX_MUTE
BEAT
BASS
QSOUND
ST_BY
GND
TAPE_PLAY
AC_SNS
+5.6V
VOL_CLK
A_MUTE
VOL_DATA
SYNC REC.
VOL_STB
R6115
R6114
R6009
SE601
IC601
R6106
R6105
C6103
C6101
C6100
R6201
C6201
Q6201
Q6200
R6109
R6108
R6107
D6901
C6903
C6900
C6901
R6104
R6111
R6112
R6113
C6200
X6001
C6104
C6105
L6900
C6102
C6205
C6204
C6906
C6206
S6500
R6501
R6502
C6501
C6502
R6007R6013 R6008
S6009
S6008
R6006
S6007
S6010
D6902
R6905C6905
CN603
R6012
R6011
R6010
C6012
C6011
C6010
C6202
C6203
C6208
R6103
C6912
C6911
C6910
C6913
C6915
C6914
R6906
C6918
R6907
S6011
S6012
R6014R6015
R6200
L6901
C6904
R6003R6005 R6004
S6005
S6004
R6002
S6003
S6002
S6001
CN602
D6951
D6952D6953
D6954D6955
R6954
R6951
C6920
C6921
C6922
R6952
R6953
LCD60
S6006
R6001
S6013
C6916
CN601
R6202R6203
C6503
8.2K
47K
18K
QLC723389B55M
10K
10K
330P
330P
330P
2.7K
0.01
2SC1740
2SC1740
47K
4.7K
4.7K
1SS133
0.01
10/16
0.01
10K
47K
10K
10K
1/50
4.5MHz
56P
56P
10
100P
100P
100P
100P
100P
JOG
1K
1K
0.01
0.01
6801.2K 820
SURR.
BASS
560
SOUND PRESET
TU DOWN
1SS133
1001000/6.3
10K
10K
10K
100P
100P
100P
1000P
100P
2200P
100K
0.01
0.01
0.01
100P
100P
100P
470
2200P
47K
TU UP
CD PLAY
1.5K2.2K
2.2K
22UH
47/10
8201.5K 1.2K
TU/BAND
FUNCTION
680
POWER
TIMER/CLOCK
MEMORY
000000000
000000
330
560
100P
100P
0.01
560
330
PRESET/REP.
560
CD STOP
1000P
1,1/8W1,1/8W
0.1
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
123
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
123
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
54
1
2
12345678910111213141516171819202122232425262728
-2-1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
4
5
6
23
24
25
29
30
32
33
34
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
58
57
56
55
54
50
51
52
53
49
44
48
47
46
45
40
41
42
43
39
35
34
33
32
63
64
26
30
35
TU_+B
TU_GND
TU_L
TU_R
CD_RST
62
27
8
9
29
3
10
11
14
TA_PLAY
17
18
21
28
37
38
36
75
71
66
65
3
4
5
6
CD_RST
11
9
14
18
17
62
38
25
63
64
TA_PLAY
65
66
21
28
27
8
36
71
75
10
26
24
23
37
TU_L
TU_+B
TU_GND
TU_R
TEST2
CQCK
RWC
DSP_RESET
BAND1
AUX_MUTE
BEAT
REMIN
BAND2
STEREO
SD
S18
S17
S20
S21
VDD
S22
S23
S24
S25
A
MUTE
SYNC_REC.
S11
S10
S9
S8
S7
S6
S5
S4
S2
S1
COM3
COM2
COM1
(VDD2)
(VDD1)
VF_CE
D_OUT
D_CLK
KY1
DIST
SELECTION
VDD
AMOSC
FMOSC
VSS
EO2
TEST1
XIN
S15
MONO
S19
SQOUT
S14
S13
S12
COIN
PICK_SW.
TU_MUTE
BASS
JOG2
WRQ
TAPE_PLAY
PB1
P_CON
PA3
SURR
DRF
S16
AC_SENS
FMIF
AMIF
LID_SW.
EO1
S3
XOUT
(POWER)
JOG1
KY0
EU-1 US JP
SS EU-2 JP
OPEN 0 8.2K
R6009
TO TUNER SEC.
DRF
SQOUT
COIN
CQCK
WRQ
RWC
TO CD SEC.
TO AMP SEC.
8.2K
10K 10K
8.2K 8.2K
10K
15K 15K 27K
CD RESET
TU_+B
TU_GND
TU_L
TU_R
TO FMOSC
(PICK_SW.)LIMI
T
R6115
MODEL JP
O
OTHER
CLOCK
AUX
CLOCK
(TV)
8.2K
This is a basic schematic diagram.
SCHEMATIC DIAGRAM (FRONT)
- 17 -- 16 -
REF
REF
FSS
CLK
TBC
FSC
CLK
REF
REF
8CM
12CM
FOADJ
FSTA
STOP
REF
GEN
FSTA
VR+0.3V
REF
FSS
FSC
TOFF
REF
REF
REF
STOP
TOSTA
TOADJ
GEN
TBC
LATCH
PONRST
DAT
CL
CE
SLOF
8/12CM
FSTA
LASER
2FREQ
TOSTA
FOSTA
EFBAL
JP-
JP+
TGL
TOFF
TES
HFL
SLOF
CV-
CV+
RF
REF
REF
FOCS
THLD
DEF
CL
DAT
CE
DRF
S.DVCC
VCC
REF
DRF
HFL
VDRF
VHFL
DEF
GAIN
VCA
PH4
BH2
PH1
BH1
RF
LASER
VPPC
RFVCC
FE1
REF
VCA
REF
REF
REF
REF
VCA
BAL
BAL
REF
BPL
VCA
VCC
Q
R
a
D
S.Q.R
SLOFSLOF
SLOF
TO
REF
REF
SPOF
REF
JP+
JP
JP-
CV+
CV-
REF
REF
FE1
REF
FOFF
REF
FSTA
FSERCH
REF
REF
JP
TOFF2
REF
TGHI
TGLI
THLDI
THLDI
TGLI
TGHI
OR
GEN
WCOMP
THLD
DEF
TGL
THLDI
TGLI
OR
AND
REF
TES
SHOCK:WCOMP
-HIST.COMP
TU_GND
TU_R
TU_L
CD_R
CD_GND
CD_L
GND
+B
X1451
C1476
C1784
C1313
C1480
R1503
R1502
R1501
R1337
C1333
R1473
R1472
C1470
C1481
C1491
C1457
C1335
C1472
R1332
C1346
C1492
C1493
R1456
C1456
C1452
R1455
C1451 R1454
C1341
R1475
C1475
R1343
IC101
C1339
C1337
C1338
C1336
C1319
R1329
C1320
R1328
C1317
R1326 R1325
C1318
R1324
C1316
C1315
R1318
R1320
R1317
R1315
R1313
C1312
R1314
C1310
R1310
R1311
C1305
R1304
R1336
R1453
C1331
R1335
L1451
C1468
C1467
C1469
R1464
R1465
R1463
R1462
C1329
C1471
R1308
C1330
R1312
IC102
C1332
C1325
C1301
R1301
R1302
C1309
R1309
C1302
R1305
C1304
R1303
C1323
R1333 R1334
C1334
C1321
R1331
R1330
C1324
C1783
R1327
C1773
C1772C1782
R1783 R1773
R1781
R1771
C1350
D1404
Q1301
C1322
IC103
CN113
C1403
C1401
Q1401
PR140
CN111
R1340
R1342
R1344
R1345
C1402
C1404
C1408
C1407
R1346
R1347
CN122
D1410
R1480
R1476
C1405
C1308
C1495
C1485
C1303
C1455
R1498
C1415
R1499
C1340
D1401 D1402 D1403
R1338
C1478
C1477
16.93M
0.022
100P
0.1
0.022
1.5K
3.3K
3.9K
6.8K
0.22;50
100K
4.7K
68P
100P
0.01
10;25
10;50
0.01
18K
33P
47;10
0.01
10K
0.01
0.1
68K
0.1 680
3300P
560
68P
100K
LA9242M
10;25
0.01
10;25
0.01
4.7;50
10K
22;50 6.8K
0.22;50
1K 56K
100P
33K
3300P
0.018
1.5K
8.2K
68K
15K
22K
1000P
22K
0.15
15K
100K
330P
6.8K
330
2.7K
0.01
10K
10;K
68P
68P
100P
1K
560
560
560
4.7;50
68P
27K
10;25
6.8K
LC78629E
0.047
2200P
47;10
100
10
0.047
330
1000P
2.2K
0.033
150K
12P
15K 1K
0.01
3300P
220K
220K
0.033
10;25
56K
10;25
1000P1000P
100K 100K
1K
1K
0.018
MTZJ5.1B
2SB810
1P
MM1469XH
470;10
470;6.3
KTA1273
400mA
82K
82K
82K
82K
0.01
0.01
100;16
0.022
150K
150K
RL153
560
1K
0.01
0.22
0.01
0.01
0.22
0.1
100
220P
100
0.1
1SS133 1SS133 1SS133
330K
100P
0.022
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
32313029282726252423222120191817
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48474645444342414039383736353433
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
49505152535455565758596061626364
32313029282726252423222120191817
28 27 26 25 24 23 22 21 20 19 18 17 16 15
1413121110987654321
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
CD_L
CD_R
DRF
WRQ
RWC
SQOUT
COIN
CQCK
A.GND
REST
COIN
SQOUT
CQCK
WRQ
CD_L
CD_R
TU_L
TU_R
TU_GND
A.GND
RWC
DRF
TU_+B
TU_GND
TU_R
TU_L
TU_+B
REST
(SLED +)
(SLED -)
(D-MUTE)
FSX
CONT2
CONT1
TEST2
DVSS
TB
F
E
FIN1
FIN2
FSS
VCC1
LDS
LDD
BH1
PH1
LF2
VR
REFI
VCC2
DRF
CE
DAT
CL
CLK
DEF
NC
TBC
FSC
DGND
SLI
SLC
RFS-
RFSM
CV+
CV-
SLOF
TES
HFL
TOFF
TGL
JP+
JP-
SL+
SL-
SLD
SLEQ
SPD
SP-
SPG
SPI
SP
AGND
FE-
FE
FA-
FA
FD-
FD
TO
JP
TD
TD-
TA
TH
SCH
TESI
TE
TE-
VVSS
PDO
ISET
TAI
DEFI
REST
XOUT
XIN
TEST5
TST11
4.2M
16M
CS
TEST1
CQCK
COIN
SQOUT
RWC
WRQ
PW
SBCK
SFSY
XVSS
EFLG
SBSY
XVDD
MUTER
RVDD
RCHO
RVSS
LVSS
LCHO
LVDD
MUTEL
NC
TEST4
TEST3
DOUT
C2F
EMPH
CONT5
CONT4
JP-
JP+
DVDD
CONT3
TGL
TOFF
FSEQ
PCK
TES
HFL
V/P
CLV-
CLV+
FR
EFMIN
EFMO
VVDD
VC
TE
FE
RF
TO FRONT PWB
BASE
MECHANISM
TU_R
RESET
TU_GND
TU_+B
WRQ
DRF
LIM_SW
COIN
SQOUT
CQCK
RWC
TU_L
5V
REG
VC
VDD
VDD
MUTE
IN
IN
IN IN
++
+
--
-
-
+
D
C
B
A
LIMIT
GND
F-
T-
T+
F+
E
VR
SL+
SP+
SL-
GND
MD
SP-
F
LD
D
A
B
C
LD
MD
GND
MD
LD
VR
T+
F+
F-
T-
F
E
LIMIT SW
SPINDLE MOTOR
SLED MOTOR
PICK UP
DT11T3CN
COMMON
SHORT
LAND
TRCKING
COIL
FOCUS
COIL
M
M
SVR
COM
SP+
SP-
SL+
SL-
LIMIT
GND
VREF
VREF
+9V
4.3
4.9
3.6
1.6
3.6
4.2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
0.0
0.0
2.2
2.5
2.2
2.5
2.5
2.5
2.5
2.5
2.9
2.5
2.5
2.5
2.5
2.5
2.3
2.3
2.3
2.3
0.0
0.0
0.0
0.0
4.8
4.8
0.0
4.8
0.0
4.8
2.4
1.6
2.4
2.4
0.0
0.0
2.5
2.5
2.5
2.5
0.0
0.0
4.9
4.9
0.2
0.0
3.6
4.2
2.2
2.2
2.5
1.0
2.5
1.0
2.5
2.5
2.5
2.5
4.9
4.9
0.0
0.0
4.8
0.0
0.0
0.0
0.0
0.0
1.5
1.5
4.8
4.8
0.0
0.0
2.3
2.3
0.0
0.0
0.0
4.8
0.0
4.8
4.8
4.8
0.0
0.0
0.0
0.0
4.8
4.8
4.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
4.7
5.1
5.1
2.1
2.1
0.0
0.0
2.1
2.1
5.1
5.1
0.0
4.7
4.8
4.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
4.8
4.8
5.0
5.0
8.0
8.2
8.0
8.4
PLAY
STOP
SCHEMATIC DIAGRAM (CD)
This is a basic schematic diagram.
PRODUCT SAFETY NOTICE
Each precaution in this manual should be followed during servicing. Components identified with the IEC symbol
!
!!
and mark in the parts list and the schematic
diagram designated components in which safety and performance can be of special significance. When replacing a component identified by
!
!!
and , use only
the replacement parts designated, or parts with the same ratings of resistance, wattage or voltage that are designated in the parts list in this manual. Leakage-
current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before returning the product
to the customer.
- 19 -- 18 -
E
E
E
1AD4B10D1715C
15 10 15 20 25
E
E
T002 94V-0
1AD4B10D1715B
C1401
A
MD
SVR
LD
GND
T-
T+
F+
F-
T002 94V-0
C1330
C1317
C1319
C1320
C1335
IC102
IC101
CQCK
COIN
SQOUT
RWC
WRQ
DRF
L1451
IC103
C
D
F
B
GND
LIMIT
SL+
SL-
SP+
SP-
J1321
J1206
Q1301
J1212
J1405
J1313
C1403
J1312
C1338
J1323
J1409
J1407
C1339
Q1401
C1301
C1333
J1327
J1412
J1403
J1404
J1318
J1317
J1316
J1315
REST
J1326
J1324
D1404
TU+B
TUGND
TU_L
TU_R
J1215
J1211
J1314
CN113
J1428
PR140
C1329
CN122
J1328
CD_R
CD_L
A_GND
+B
GND
TUGND
TU_R
TU_L
J1202
J1322
400
CN111
J1411
J1420
C1773
J1210
J1424
J1425
J1325
J1423
J1415
J1414
J1418
J1417
J1410
J1209
C1408
J1213
J1426
J1427
COMMON
VREF
J1402
J1203
J1400
LIM SW
J1300
J1301
J1302
J1303
J1304
J1305
J1306
J1307
J1308
J1309
J1310
J1311
D1410
J1408
D1401
D1402
D1403
J1214
J1421
J1422
C1457
J1320
J1401
J1413
J1204
J1406
J1208
C1783
C1492
J1200
J1319
J1205
J1416
J1419
X1451
TU+B
C1476
J1207
C1478
LCD60
S6003
S6004
S6005
S6006
S6013
S6010
S6012
S6011
S6009
S6008
S6007
S6001
S6002
SE601
S6500
X6001
L6901
CN602
Q6201
Q6200
J6310
J6311
J6312
J6313
J6314
J6315
J6200
J6201
J6202
J6204
J6106
C6904
J6114
L6900
D6902
D6901
J6302
J6303
J6304
J6305
J6301
J6105
J6117
J6208
J6118
J6111
J6112
J6108
J6104
J6309
J6120
J6110
J6102
J6119
J6100
J6113
POWER
FUNCTION
TU/BAND
PRESET
CD STOP
CD PLAY
TUN DOWN
TUN UP
SURROUND
CLOCK/TIMER
MEMORY
BASS
SOUND
C6200
J6115
SQOUT
COIN
CQCK
RWC
RST
BEAT
TU_MUTE
WRQ
DRF
LIMT SW.
J6307
BAND2
BAND1
MONO
SD
J6300
FMOSC
J6103
J6116
VOL_STB
VOL_DATA
VOL_CLK
AC_SNS
GND
LID_SW.
AMIF
AMOSC
TU_+B
TU_GND
TU_R
TU_L
VT
GND
J6308
STEREO
TU_L
TU_R
GND
TU_+B
J6109
J6206
J6121
J6123
J6126
C6905
J6125
J6207
+B
GND
C6900
J6306
J6101
CN603
J6209
J6205
J6107
J6203
ST_BY
SYNC_REC.
+5.6V
A_MUTE
TAPE_PLAY
BASS
AUX_MUTE
QSOUND
J6122
CN601
GND
R1343
C1325
R1332
R1333
C1323
R1334
R1336
R1335
C1303
R1305
R1304
R1303
C1309
C1308
C1305
C1304
R1308
R1309
R1310
R1311
C1310
R1312
R1313
C1312
R1315
R1318
R1318
C1318
C1318
R1329
R1329
C1302
C1302
R1302
R1302
C1324
C1324
C6922
C6922
C6208
C6208
R6005
R6005
R6013
R6013
R6014
R6014
R1318
R1320
CAN1
R1324
C1318
R1328
R1325
R1327
R1326
R1329
R1453
R1301
R1301
C1407
C1407
C6104
C6104
R6001
R6001
R6200
R6200
CAN
CAN
R1301
C1315
C1316
R1314
C1302
R1302
C1341
C1322
C1324
R1456
C1452
C1456
R1455
C1451
C1471
C1772
C1782
C1782
C1404
C1404
R1773
R1773
C1405
C1405
R6502
R6502
R6501
R6501
R6006
R6006
C6912
C6912
C1782
R1781
R1781
R1781
C1346
C1493
C1472
R1783
C1481
R1331
R1330
R1472
R1337
C1336
R1463
C1475
C1470
R1464
C1469
C1468
C1467
R1475
R1503
R1502
R1501
R1473
C1340
C1402
C1313
C1332
R1480
C1404
R1499
C1455
C1485
C1495
C1415
R1454
C1350
R1317
C1321
R1773
R1771
R1462
C1331
R1476
C1405
R1465
C1491
R1347
R1344
R1345
R1340
R1342
R1346
C1407
R1338
C1337
C1480
C1334
C1477
R1498
R1600
C1784
IC601
C6104
C6105
C6913
C6914
C6915
R6906
C6918
C6920
C6921
R6103
R6502
R6008
C6502
R6501
C6501
C6206
R6907
C6922
R6112
C6010
C6011
C6012
R6010
R6011
R6012
R6107
R6108
R6111
R6201
C6201
C6102
C6103
C6903
C6101
C6100
C6202
C6203
C6911
R6109
R6905
C6208
R6009
R6001
R6002
R6003R6004
R6005
CAN
R6006
R6007
R6013
R6014
R6015
R6106
R6105
R6104
C6916
C6910
R6113
C6906
C6901
C6204
C6912
C6205
R6200
R6115
R6114
CAN
CAN
CAN
R6202
R6202
R6202
CAN
R6203
CAN
FRONT P.W. BOARD
WIRING DIAGRAM ( FRONT & CD )
This is a basic wiring diagram.
CD P.W. BOARD
- 21 -- 20 -
TO CN490 CD GND
TU_EARTH
GND
STEREO
SD
LID_SW
VT
MONO
TU_GND
TU_+B
TU_R
AMOSC
BAND1
MUTE
AMIF
BAND2
TU_L
IC201
C2005
C2002
C2008
R2003
R2014
C2017
C2003
L2002
L2003
R2001
C2001
R2005
R2002
C2015
C2011
C2012
C2014 C2013
C2009
XF211
XF212
R2113
CT211
C2102
C2103
Q2101
R2101
C2101
C2104
R2104
R2106
C2108
C2106
C2107
C2110
IC211
L2205R2117
Q2201
R2119
R2201
C2209
R2107
C2122
C2120
C2118
C2117
C2702
C2802
C2121
C2119
D2101
C2801
C2701
R2205
Q2102
R2206
C2218
R2701
C2019
C2140
C2021
C2141
Q2110
R2004
R2801
L2204
C2311
Q2111
R2128
R2127
C2207
R2210
D2003
D2002
D2102
C2025
Q2001
R2007
R2009
C2020
R2008
C2027
L2005
L2007
CN201
D2004
D2005
R2006
C2312
L2006
R2105
T2001
S2001
CN202
R2126
CN203
C2026
C2113
C2115
C2114
R2301
R2302
C2111 R2303
C2112
C2010
TO FRONT GND
T2002
C2022
C2029
D2006
XF215
L2001
FMOSC
R2901
XF210
C2126
C2142
R2131
C2131
Q2002
R2011
R2010
D2104
Q2003
R2129
C2902
R2900
C2024
LA1186N
0.01
0.022
15P
18
100K
1000P
3P
8.2UH
330K
0.01
22
10K
0.022
15P
5P
0.01 0.022
0.47/50
10K
0.01
0.01
KRA107M
3.9K
0.01
10/25
10K
2.7K
100/10
0.47/50
1/50
0.047
LA1844ML
820K
KRA107M
100K
100
1000P
33K
0.022
0.022
0.033
680P
0.022
0.022
4.7/50
22/25
1SS133
2.2/50
2.2/50
68K
KRC107M
2.2K
100/10
15K
0.022
0.1
1000P
1P
KRC107M
10K
15K
0.022
KTC3195
330K
4.7K
0.022
1.0K
SVC211-B--C
SVC211-B--C
SVC342
1000P
KTC3195-O
560K
330
0.022
220
100P
22UH
22UH
AM ANT TERMANL
1SS133
1SS133
560
10/25
22UH
10K
15P
120K
1000P
1/50
4700P
0.1
68K
22K
10/25 18K
4.7/50
100P
10.7MHZ
1P
0.01
1SS133
450KHz
1K
0.047
22P
56K
560P
KTC3195-O
120K
100
MTZ5.6B
KTC3199-GR
22K
47P 0.1
123456789
121110987654321
24 23 22 21 20 19 18 17 16 15 14 13
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
123
(E)
(CH)
(CH)
(MW)
(MW)
TP202
TP201
(CH)
TP203
FM 75 OHM
AM LOOP
-1
S2001-2
TO FRONT CN603
2P-9P
(H)
(CH)
0.95 1.63 4.66 0 0 4.66 0 3.98 4.66
0
0
3.56
0
0
4.82
2.11
2.11
4.75
4.9
2.11
2.11
2.09
2.10
0
0
4.84
4.84
4.83
4.84
2.70
3.38
4.75
4.90
0
0
3.57
1.55
3.57
0
3.71
3.55
1.12
1.13
1.16
1.17
2.1
2.1
2.16
0.18
2.75
1.53
0
2.26
1.26
1.53
2.06
2.09
2.07
2.10
4.75
4.90
3.30
3.45
4.70
4.87
4.74
4.90
0
0
00.0
00.0
00.0
00.0
00.0
00.0
FM
AM
0
4.5
0.7
R OUT L OUT
0.7
0.8
0
SCHEMATIC DIAGRAM (TUNER)
This is a basic schematic diagram.
- 23 -- 22 -
WIRING DIAGRAM (TUNER)
This is a basic wiring diagram.
E
MW ANT
MW OSC
E
E
E
BAND1
LID_SW
IF
SD
FR_GND
AM OSC
VT
AMPGND
TU_L
TU_R
ST
MONO
MUTE
BAND1
BAND2
VT
1AD4B10D1712D
T002 94V-0
LW OSC
+B 9V
E
E
E
E
L2205
XF212
IC201
XF211
CT211
Q2001
D2005
D2004
D2102
SH201
D2002
D2003
C2009
J2110
L2003
J2109
J2211
C2104
J2209
C2111
C2119
C2121
C2801
C2701
C2106
C2113
C2107
D2101
L2005
Q2101
L2006
J2203
J2206
J2105
C2312
C2108
Q2111
J2307
C2218
J2302
Q2201
J2101
J2205
S2001
J2208
J2304
CN201
L2002
J2306
J2102
J2103
C2112
T2002
IC211
T2001
XF215
D2006
J2303
J2108
U
J2106
L2204
XF210
J2212
L2007
Q2002
Q2003
D2104
CN203
CN202
Q2102
J2107
J2210
J2301
J2104
Q2110
J2300
J2202
J2200
J2201
J2100
J2207
J2204
J2305
R2129
L2001
C2131
C2142
R2131
C2024C2005
C2002
R2001
C2001
C2014
C2011
C2003
R2008
C2101
C2117
C2122
C2702
C2802
R2106
R2206
R2201
C2115
R2301
C2114
C2022
R2900
C2001
R2002
C2014
R2005
C2013
R2004
R2003
C2011
C2012
C2008
C2015
R2014
C2017
C2003
R2006
R2008
R2007
R2009
C2021
R2101
C2101
C2118
C2117
C2120
C2122
C2702
C2802
R2801
R2701
C2103
C2102
R2104
R2106
C2110
C2126
R2113
R2117
R2119
C2209
C2020
C2019
C2311
C2207
R2128
R2127
R2206
R2201
C2027
C2140
C2025
R2126
C2026
C2115
R2301
C2114
R2303
R2302
R2105
C2010
R2205
C2022
C2029
R2901
R2010
R2011
R2210
C2141
R2900
C2902
R2107
- 25 -- 24 -
TU_GND
TU_RCH
TU_LCH
CD_RCH
A_GND
CD_LCH
CD_GND
CD_+B
AUX_MUTE
BEAT
BASS
QSOUND
ST/BY
GND
TAPE_PLAY
AC_SENS
5.6V
VOL_CLK
A_MUTE
VOL_DATA
SYNC_REC
VOL_STB
C4854
C4855
R4911
Q4902
C4920
R4910
C4919
R4912
C4921
C4918
IC412
R4718
C4713
C4911
R4818
C4813
C4815
C4714
C4715
C4814
C4716
C4913
R4781
C4912
C4816
R4881
C4712C4812
C4905
C4909
R4905
CN406
L4902
R4941
CN405
Q4951
D4951
R4951
C4952
C4951
R4952
R4752
R4852
C4953
PR495
C4916
Q4751
Q4851
R4756
R4856
R4961
D4961
D4963
D4962
R4962
C4751
C4851
C4961
R4717R4817
R4816
R4716
Q4904
C4906
CN421
R4938
C4811
C4711
IC411
R4736
C4735
C4736
R4737
R4738
R4739
C4742
C4734
C4738R4740
R4741
R4742
R4745
C4739
C4740
C4741
R4746
R4747
C4743
C4843
R4843
R4847
R4846
C4841
C4840
C4839
R4845
R4842
R4841
R4840C4838
C4834
C4842
R4839
R4838
R4837
C4836
C4835
R4836
C4726
C4826
C4731
C4732
C4831
C4832
C4837
R4949
R4833
R4834
R4832
R4831
R4948
R4734
R4733
R4732
R4731
R4735
R4730
R4830
C4833
R4835
C4730
C4733
Q4106
R4106
R4704
R4703
R4803
R4804
C4704
C4804
C4703
C4803
R4901
C4901
C4802
C4702
C4807
C4707
C4701
C4801
R4710
R4810
C4805
C4705
R4805
R4705
C4806
C4706
R4708
C4708
C4709
R4709
C4808
R4808
R4809
C4809
R4848
R4849
R4850
R4751
R4748
R4749
R4750
R4851
CN401
CN402
S4950
IC410
R4853
R4753
R4761
R4760
R4861
R4860
Q4103
Q4903
D4102
Q4104
R4107
PR496
R4770
R4870
R4971
C4844
Q4830
Q4730
C4744
D4953
C4962C4963
R4991
CN490
C4984
C4723
C4823
Q4840
Q4740
R4857
R4859
R4858
R4757
R4759
R4758
R4914
C4110
R4110
R4108
Q4108
Q4109
R4109
C4852 C4752
C4853 C4753
C4750
C4850
Q4992
Q4994
R4953
C4915
IC446
D4993
C4994
C4997
R4104
R4105
CN491
C4993
R4743
Q4995
R4955
R4954
L4780
L4781
L4881
C4983C4982
D4982 D4983
D4981D4980
C4981C4980
CN215
CN216
CN441
L4591
CN450
CN451
AC 230-240V
50Hz
CN452
0.01
0.01
12
2SC3330
0.01
10K
0.01
330
10/25
1000P
TA8229K
TA8229K
390
47/10
330/10
390
47/10
100/16
0.15
100/16
0.15
1000/16
3300/25
150
220/25
1000/16
150
3300P
3300P
10/25
220/10
100
27
KTD2058
MTZJ9.1B
470
0.022
47/25
470
2.2
2.2
470/16
1250mA
180P
2SD1012
2SD1012
4.7K
4.7K
10K
1SS133
1SS133
1SS133
1K
1/50
1/50
1;50
15K
15K
1K
1K
2SC3330
1000P
10K
10/25
10/25
LC75392
47K
150P
6800P
18K
1K
47K
2200P
0.01
0.01522K
27K
10K
15K
470P
3300P
47P
82K
68K
10P
10P
100K
68K
82K
47P
3300P
470P
15K
10K
27K
22K0.015
0.01
2200P
47K
1K
18K
6800P
150P
47K
1/50
1/50
1/50
1/50
1/50
1/50
470/6.3
2.2K
3.9K
3.9K
5.6K
47K
2.2K
3.9K
3.9K
5.6K
47K
3.9K
12K
12K
1/50
3.9K
100/10
1/50
KRC102M
10K
3.9K
56
56
3.9K
47/10
47/10
0.022
0.022
510K
47/10
1000P
1000P
2200P
2200P
10/25
10/25
3.9K
3.9K
1000P
1000P
18K
18K
270P
270P
18K
2200P
560P
820
2200P
18K
820
560P
22K
47K
22K
22K
22K
47K
22K
22K
BA3314
180K
180K
1K
1.5K
1K
1.5K
KRA102M
TKTC3199
1SS133
KRC102M
47K
1500mA
47K
47K
100
5600P
KTA1267
KTA1267
5600P
1SS133
10/1610/16
10K
0.01
1/50
1/50
KRC102M
KRC102M
8.2K
1.5K
5.6K
8.2K
1.5K
5.6K
2.7K
100/10
1K
3.3K
KRC107M
KRC107M
3.3K
0.15 0.15
0.22 0.22
0.01
0.01
KTA1271
KRC107M
4.7K
1/50
NJM78L05A
1SS133
47/10
0.01
100K
10K
10/25
100K
KTA1271
47K
4.7K
22U
22U
22U
0.01
0.01
RL153 RL153
RL153RL153
0.010.01
000
15 14 13 12 11 10 9
12345678
89101112 13 14
123456789101112131415
302928272625242322212019181716
1234567
1
2
3
4
5
6
7
8
123
1
2
3
4
5
6
7
8
9
10
11
12
13
14
S4950-1~2 R/P SW
S4904 MECHA MOTOR SW
SP471
SP481
LEFT
RIGHT
HEAD PHONE
(1/2)
(2/2)
R
P
ALCNC OUT1NCOUT2NF2 NF3
NF1IN1GNDGNDVCCIN2FILTER
MAGNETIC
EHEAD
WOOFER
WOOFER
+
P
R
R/P
HEAD
-
(FUSE)
L-CH
R-CH
MOTOR
S4904
(FUSE)
(FUSE)
S4950-2
TO CD
(AMP BLOCK)
(MYLAR)
TO FRONT BLOCK
LVR
OUT
LVR
IN
LT
OUT
LT
COM
LT4
CLASSIC
LT3
POP
LT2
ROCK
LT1
FLAT
L4
IN
L3
IN
L2
IN
L1
IN
VDDCLDI
CE VSS VREF
R1
IN
R2
IN
R3
IN
R4
IN
RT
COM
RT
OUT
RVR
IN
RT1
FLAT
RT2
ROCK
RT4
CLASSIC
RT3
POP
RVR
OUT
P
P
P
P
P
PR
R
R
R
R
R
S4950-1
S4950-5
S4950-6
S4950-7
S4950-8
S4950-4
S4950-3
FU401
T2.5A L 250V
T4981
0
4.3
0
0.6
0
0.1
00 0
5.9
0.6 0.60 6.3
11.3 5.9 12.0 11.3 0 11.6
PLAY
REC
9.0
12.0
9.6
PRODUCT SAFETY NOTICE
Each precaution in this manual should be followed during servicing. Components identified with the IEC symbol
!
!!
and mark in the parts list and the schematic
diagram designated components in which safety and performance can be of special significance. When replacing a component identified by
!
!!
and , use only
the replacement parts designated, or parts with the same ratings of resistance, wattage or voltage that are designated in the parts list in this manual. Leakage-
current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before returning the product
to the customer.
SCHEMATIC DIAGRAM (AMPLIFIER)
This is a basic schematic diagram.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Sanyo DC-DA1000 User manual

Category
Cassette players
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI