TAG HDIT 850D-36M Reference guide

TAG
Brand
TAG
Model
HDIT 850D-36M
Category
Security device components
Type
Reference guide
Reference Manual
22355 TAG WAY
Dulles, VA 20166-9310
Technical Support: (877) TAG-TECH
+1 (703) 406-4516
www.tag.com
31 JUL 01
HDIT 850D-36M
8
TAG
®
Contact Information:
Mailing Address:
Technology Advancement Group
®
, Inc.
22355 TAG WAY
Dulles, VA 20166-9310
USA
Telephone Numbers:
Headquarters
+1 (703) 406-3000
Toll-Free 1 (800) TAG-POWER (CONUS Only)
0800 - 1700 Eastern Time (USA)
Tech Support
+1 (703) 406-4516
Toll-Free 1 (877) TAG-TECH (CONUS Only)
24 Hours-A-Day, 365 Days-A-Year
Internet:
Web Site
tag.com
E-Mail
[email protected]
When servicing the HDIT-850D-36M, disconnect the unit from the power
source, and remove the power cord (See Page 5). All 22 (See Figure 11) screws
need to be removed from the Top Access Panel to service the unit.
Note: The two screws are located on the Front Panel of the HDIT-850D-36M.
Failure to remove those will result in damaging the Top Access Panel.
The HDIT-850D-36M should never be serviced without contacting TAG’s Tactical
Technical Support Team first.
TAG’s Tactical Technical Support Team
+1 (703) 406-4516
Toll-Free 1 (877) TAG-TECH (CONUS Only)
24 Hours-A-Day, 365 Days-A-Year
Top Access Removal Instructions
Figure 11
7
Table of Contents:
Features 1
Front Panel
Front Panel - Power & Reset Switches 2
Front Panel - CD-ROM 3
Front Panel - Removable Hard Drives 3
Rear Panel
Rear Panel 4
Rear Panel - Power Supply 5
SCSI IDs 6
NT 4.0 Load 7
Top Access Removal 8
©2001Technology Advancement Group, Inc. All rights reserved.
Technology Advancement Group, TAG, HDIT, and the TAG Ball graphic are trademarks or regis-
tered trademarks of Technology Advancement Group, Inc. This manual and/or its contents may
not be duplicated without written permission of Technology Advancement Group, Inc.
Printed in the USA
Figures:
Figure 1 Front Panel Power & Reset Switches 2
Figure 2 Removable Hard Drive 3
Figure 3 CD-ROM 3
Figure 4 Rear Panel 4
Figure 5 Rear Panel - I/O Ports 4
Figure 6 Rear Panel - Power Supply 5
Figure 7 SCSI IDs 6
Figure 8 Top Access Screw Removal 8
NT 4.0 Server Load Instructions
Steps for loading Windows NT Server 4.0 on TAG 2U RAID Servers
1) Boot the computer with a bootable floppy (ie Windows 95 startup disk).
(disk must contain Command.Com and Fdisk).
2) Execute Fdisk and create a 4GB partition on the Hard Drive.
3) Remove the bootable floppy and put the NT 4.0 Server CD in the Drive.
4) Change the boot priority (in CMOS) so that the CD-ROM is now the primary
boot device.
5) When NT 4.0 Server begins to load press the <F6> key.
6) Type <S> and load the MegaRAID drivers for the RAID card.
7) After drivers have loaded hit <Enter>.
8) On the 1
st
Setup screen hit <Enter>.
9) Type <S> and load the Adaptec 7800 Ver3.02 drivers for NT. When prompted
select the U2 drivers for NT4.
10) Allow NT 4.0 Server to continue the load.
11) Delete the 4GB partition you created (with Fdisk).
12) Install NT 4.0 Server into the 4GB of unpartitioned space now recognized
by NT 4.0 Server.
13) Choose NTFS as your file system.
14) Follow all screen prompts until NT 4.0 Server asks to be rebooted.
15) When NT 4.0 Server resumes Setup (now in GUI) follow all screen prompts.
16) Install network drivers for the onboard network card (from diskette).
17) Finish NT 4.0 Server load.
6
Features
The HDIT-850D-36M, as all products in the HDIT product line, is specifically
designed to provide unsurpassed performance and reliability where rack space is
very limited. The HDIT-850D-36M has the following features:
• 2U heavy-duty industrialized 90-mil. rack-mount server chassis (24”x19”x3.5”)
• Heavy-Duty slide rails
• 300W auto-switching power supply
• 2 high performance blowers for & thermal dissipation across the HDIT chassis
• 850MHz. Pentium
®
III processor with 512KB high-performance cache
• Genuine Intel
®
motherboard featuring the L440GX+ chipset
• On-board dual-channel SCSI controller
• On-board 2MB SGRAM video adapter
• On-board 100MB Fast Ethernet card
• 768MB 100MHz. SDRAM/ECC RAM, expandable to 2GB
• (2) 36GB Ultra-Wide SCSI, hot-swap hard drives in metal carrier & receiver
• Internal 48x CD-ROM
• 3.5” 1.44MB Floppy Drive
• 1 year parts & labor warranty, and lifetime 24x7 telephone technical support
1
The HDIT-850D-36M is featured with several SCSI devices, each with its own
unique SCSI ID. The following is a list of all SCSI peripherals and their respective
SCSI IDs.
SCSI IDs
SCSI ID Device
0 Hard Drive (Left)
1 Hard Drive (Right)
Figure 6
5
Front Panel - Power & Reset Switches
The HDIT-850D-36M features 2 switches mounted centrally on the front panel.
To power up the HDIT-850D-36M, press hold the power switch. The Power LED
(green) will then glow indicating power is being supplied to the unit.
NOTE: If the unit does not power up, check the power connections
and the main power switch on the back panel below the power
supply.
The second switch is the system reset switch. Press the switch to reset the HDIT-
850D-36M, (See Figure 1).
2
Rear Panel - Power Supply
Situated on the back of the HDIT-850D-36M is an Auto-Switching 115/
230VAC power supply, (See Figure 5). The system main power switch is located
just beneath the power supply’s cooling fan. Turn off the main power switch and
remove the power cord from the HDIT-850D-36M before servicing or moving the
unit.
Rear Panel - Power Supply Specifications
INPUT: 115/230VAC 60/50Hz 10/5A
OUTPUT: 300W (Total Combined MAX)
(+5V/+3.3V Total MAX 140W)
OUTPUT: +5VDC @ 30A +12VDC @ 14A
-5VDC @ 0.3A -12VDC @ 1.0A
+3.3VDC @ 22A +5VDC @ 0.2A
Figure 1
Figure 5
4
3
The HDIT-850D-36M is equipped with two removable 36GB Ultra Wide SCSI hard
drives, (See Figures 1 & 2). TAG has configured the removable drives with the follow-
ing SCSI ID’s: The left drive, is SCSI ID #0 and the right drive, is SCSI ID # 1. Depend-
ing on the configuration, the drives may not be hot-swappable. If the HDIT-850D-
36M is configured to mirror the two drives, then the drives may NOT be removed
while the unit is powered up. If the HDIT-850D-36M is configured to utilize just the
two drives, then the system drive (holding the O/S) can NOT be removed while the
system is running (hot). The other drive may be removed while the system is running.
NOTE: If you are unsure of the system configuration, power down the unit
to remove either drive.
To remove either drive, insert the hard drive module key and turn the keylock
clockwise to the unlocked position. Grab the handle and slide the drive out. Insert
the replacement drive into the HDIT-850D-36M and turn the keylock counter-
clockwise to the locked position.
Front Panel - Removable Hard Drives
Front Panel - CD-ROM
The HDIT-850D-36M is equipped with a 48x CD-ROM, (See Figures 1 & 6). To
load a CD, press the CD tray eject button. Place the CD on the CD tray, and press
the tray eject button again. The CD activity light will illuminate intermittently, as
the CD is read.
Rear Panel
The connectors for all of the external peripherals are located on the left side of
the rear panel of the HDIT-850D-36M, (See Figures 3 & 4). When connecting
peripherals, make sure the connectors are well seated in the port.
The main system power switch is located below the power supply on the
right side (See Figure 5). When mounting the HDIT-850D-36M into a rack, please
make sure all connections are secured in their appropriate ports before sliding the
unit into the rack.
Figure 3
Figure 2
Figure 3
Figure 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

TAG HDIT 850D-36M Reference guide

TAG
Brand
TAG
Model
HDIT 850D-36M
Category
Security device components
Type
Reference guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents