Page is loading ...
ASUS MiraCast
2
English
Package contents
NOTES: If any of the items is damaged or missing, contact your retailer.
Knowing the parts
LED indicator
cover
HDMI connector
Micro USB port ASUS MiraCast
reset button
IMPORTANT!
• Use the micro USB port to connect the ASUS MiraCast to a power source.
• Doing rmware updates ensures that your ASUS MiraCast has the latest
software installed. To enable this, press and hold the ASUS MiraCast
button for more than ve (5) seconds.
• Press and hold the ASUS MiraCast button for more than ten (10) seconds
to restore your ASUS MiraCast to its factory settings.
ASUS MiraCast power adapter micro USB cable
ASUS Tablet
technical
documentations
ASUS MiraCast
3
English
Using your ASUS MiraCast
NOTE: The following illustration is for reference only.
A. Connect the micro USB
cable to your ASUS
MiraCast.
B. Plug your ASUS MiraCast
to the power adapter.
C. Plug the power adapter to
a power source.
D. Connect the HDMI
connector of your ASUS
MiraCast to the HDMI port
of your external monitor or
display.
E. Turn on your tablet or mobile device and follow the steps shown onscreen.
NOTE: For more details on updating your ASUS MiraCast’s rmware, refer to
http://www.asus.com/Tablet_Mobile_Accessories/
ASUS MiraCast
connection
Firmware update Factory reset
Blue (5 seconds after
connecting to
display) ASUS
MiraCast is turned
on.
Red Preparing for
rmware update.
Purple Preparing for
factory reset.
Blinking
blue
Currently
connecting to ASUS
MiraCast.
Blinking
red
Update ongoing Blinking
purple
Factory reset
ongoing
Blue Connection is
ready.
Blue Firnware update
is done
Blue Factory reset is
done
LED indicator table
ASUS MiraCast
40
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter. End-users and installers must be provide with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure compliance.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
This device is slave equipment, the device is not radar detection and not ad-hoc operation in
the DFS band.
ASUS MiraCast
41
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Canada, avis d’Industry Canada (IC)
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas
causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les
interférences qui peuvent aecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio
frequency exposure limits. The Wireless Device should be used in such a manner such that the
potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under
mobile exposure conditions. (antennas are greater than 20cm from a person’s body).
Informations concernant l’exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans l est inférieure à la limite d’exposition aux
fréquences radio d’Industry Canada (IC). Utilisez l’appareil de sans l de façon à minimiser les
contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux RF d’
IC dans des conditions d’exposition à des appareils mobiles (les antennes se situent à moins de
20 cm du corps d’une personne).
• The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for
harmful interference to co-channel mobile satellite systems;high power radars are allocated
as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and
these radars could cause interference and/or damage to LE-LAN devices.
The Country Code Selection feature is disabled for products marketed in the US/Canada
ASUS MiraCast
42
Manufacturer ASUSTek COMPUTER INC.
Address, City 4F, No. 150, LI-TE RD., PEITOU,
TAIPEI 112, TAIWAN
Country TAIWAN
Authorized
Representative
in Europe
ASUS COMPUTER GmbH
Address, City HARKORT STR. 21-23, 40880 RATINGEN
Country GERMANY
NCC
低功率電波輻射性電機管理辦法
第十二條： 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使
用者均不得擅自變更頻率、加大功率或變更原設計之特性及功
能。
第十四條： 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發
現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使
用。低功率射頻電機需忍受合法通信或工業、科學及醫療用電波
輻射性電機設備之干擾。
*減少電磁波影響，請妥適使用。
Copyright Information
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or tranPadd into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without
the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
The ASUS logo is a trademark of ASUSTek Computer Inc. Information in this document is subject
to change without notice.
Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved.
support.asus.com
/
