Parkside PFSPS150 User manual

DREIECKSCHLEIFER

Kompernaß GmbH

Burgstraße 21

44867 Bochum (Germany)

Last Information Update · Tietojen tila · Informationsstatus

Tilstand af information · Opplysningenes gyldighet

Έκδοση των πληροφοριών · Stand der Informationen:

04 / 2008 · Ident.-No.: PFSPS150042008-3

GB / IE / CY Operation and Safety Notes Page 5

FI Käyttö- ja turvallisuusohjeet Sivu 13

SE Bruksanvisning och säkerhetsanvisningar Sidan 21

DK Brugs- og sikkerhedsanvisninger Side 29

NO Betjenings- og sikkerhetshenvisninger Side 37

GR / CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 45

DE / AT Bedienungs- und Sicherheitshinweise Seite 53

PAINT SPRAY GUN

PFSPS150

Paint SPray Gun

Operation and Safety Notes

ruiSkutuSPiStooli

Käyttö- ja turvallisuusohjeet

Πιστόλι βαφήσ χρώματόσ

Υποδείξεις χειρισμού και ασφαλείας

MalerSPrøyte

Betjenings- og sikkerhetshenvisninger

SPrøjtePiStol

Brugs- og sikkerhedsanvisninger

FärGSPrutPiStol

Bruksanvisning och säkerhetsanvisningar

FarBSPritZPiStole

Bedienungs- und Sicherheitshinweise

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Slå opp begge sidene med illustrasjoner før bruksanvisningen leses. Bli først kjent med alle apparatets

funksjoner.

Før du læser, vend begge sidene med billeder frem og bliv bekendt med alle apparatets funktioner.

Käännä ennen lukemista molemmat kuvalliset sivut esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of

the device.

Vik ut båda bildsidorna och ha den till hands när du läser igenom anvisningarna och gör dig bekant

med apparatens / maskinens funktioner.

Page is loading ...

5 GB/IE/CY

Table of Content

Introduction

Proper use .....................................................................................................................Page 6

Features and equipment ...............................................................................................Page 6

Included items ...............................................................................................................Page 7

Technical data ...............................................................................................................Page 7

General safety advice

1. Your working area ....................................................................................................Page 7

2. Electrical safety ........................................................................................................Page 8

3. Personal safety .........................................................................................................Page 8

4. Use and handling of the electrical power tool ......................................................Page 8

Safety advice relating speciﬁcally to paint spray guns .............................................Page 9

Advice on use

DIN-sec / Viscosity ........................................................................................................Page 9

Preparing the sprayed medium ...................................................................................Page 9

Switching On/Oﬀ ........................................................................................................Page 10

Spraying process ..........................................................................................................Page 10

Servicing and cleaning .................................................................................Page 10

Disposal ......................................................................................................................Page 10

Information

Service centre ...............................................................................................................Page 11

Declaration of Conformity / Manufacturer ................................................................Page 11

6 GB/IE/CY

Introduction

Paint spray gun PFSPS 150

Q

Introduction

Please make sure you familiarise yourself

fully with the way the device works before

you

use it for the ﬁrst time and that you

understand how to handle electrical power tools

correctly. To help you do this please read the

accompanying operating instructions. Keep these

instructions in a safe place. If you pass the device

on to anyone else, please ensure that you also

pass on all the documentation.

Q

Proper use

This device is intended for the application of paints,

varnishes etc. in a private (non-commercial) envi-

ronment. You can use the device to apply a sprayed

medium with a viscosity up to 100-DIN-sec. Any

other use or modiﬁcation shall be deemed to be

improper use and could give rise to considerable

risk of accident. We will not accept liability for loss

or damage arising from improper use. The device is

intended for private, domestic use only.

Q

Features and equipment

1

Attachment screw

2

Regulator button

3

On / Oﬀ switch

4

Pump piston

5

Spring

6

Suction tube

7

Paint cup

8

Nozzle

9

Suction-pressure valve

10

Pump housing

11

Cleaning nozzle

12

Measuring cup

13

Nozzle extension

The following icons / symbols are used in this instruction manual:

Read instruction manual!

Wear hearing protection, dust protection

mask, protective glasses and

protective gloves.

Observe caution and safety notes!

Keep children and other unauthorised

personnel at a safe distance when

using electrical tools.

Caution – electric shock!

Dangerous electric current –

danger to life!

Keep the device away from rain or

moisture. Water entering an electrical

device increases the risk of electric shock.

Explosive material!

Damaged appliances, power cables

and power plugs mean potentially fa-

tal risks from electric shock. Regularly

check the condition of the appliance,

the power cables and the power plugs.

W

Watts (Eﬀective power) No smoking!

Safety class II

Dispose packaging and appliance in

an environmentally-friendly way!

7 GB/IE/CY

Introduction / General safety advice

Q

Included items

1 Electric paint spray gun

3 Nozzles* 1 x 0.6, 2 x 0.8 mm

3 Suction pressure valves*

2 Springs*

1 Cleaning nozzle

1 Nozzle extension

1 Measuring cup

1 Operating instructions

1 Booklet covering „warranty and service“

* 1 x preﬁtted

Technical data

Rated power: 150 W

Delivery capacity: 400 g / min (water)

Viscosity capacity: max. 100 DIN-sec

Pressure: max. 250 bar

Paint cup: 0.7 litre

Protection class: II /

Noise and vibration data:

The sound pressure level (A-weighted) of the

device is typically 93.9 dB (A).

Uncertainty K=3 dB.

The sound level while working can exceed

106.9 dB (A).

Wear ear protection!

Weighted acceleration, typical: 6.5 m / s

2

WARNING!

The vibration level given in these

instructions has been measured in accordance with

a standardised measurement procedure and can

be used to compare devices.

Diﬀerent uses of the device give rise to diﬀerent

vibration levels and in many cases they may exceed

the values given in these instructions. In some cir-

cumstances it is easy to underestimate the vibration

load if the electrical power tool is used regularly.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General safety advice

J CAUTION! Please read all the instructions

and advice. Failure to observe the instructions

and advice given below may result in electric

shock, ﬁre and/or serious injury.

MAKE SURE THAT YOU KEEP THESE INSTRUC-

TIONS AND SAFETY ADVICE IN A SAFE PLACE.

1. Your working area

a) Keep your working area clean and

clutter-free. Untidy or poorly lit working

areas can lead to accidents.

b)

Do not work with the device

in potentially explosive envi-

ronments in which there are

inflammable liquids, gases or dusts.

Electrical power tools create sparks which can

ignite dusts or fumes.

c)

Keep children and other peo-

ple away while you are op-

erating the electrical power

t o o l . Distractions can cause you to lose

control of the device.

8 GB/IE/CY

General safety advice

2. Electrical safety

To avoid danger to life from

electric shock:

a) The mains plug on the device must

match the mains socket. The plug

must not be modified in any way.

Do not use an adapter plug with

devices fitted with a protective earth.

Unmodiﬁed plugs and matching sockets

reduce the risk of electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c)

Keep the device away from

rain or moisture. Water entering

an electrical device increases the risk

of electric shock.

d)

Do not use the mains lead for

any purpose for which it was

not intended, e.g. to carry

the device, to hang up the device or

to pull the mains plug out of the mains

socket. Keep the lead away from

heat, oil, sharp edges or moving

parts of the device. Damaged or tangled

mains leads increase the risk of electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD) for

protection if operating the electrical

power tool in a moist environment is

unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence

of drugs, alcohol or medication. One

moment of carelessness when using the device

can lead to serious injury.

b)

Wear personal protective

equipment and always wear

safety glasses. The wearing of

personal protective equipment such as dust

masks, non-slip safety shoes, safety helmets or

ear protectors, appropriate to the type of elec-

trical power tool used and work undertaken,

reduces the risk of injury.

c) Avoid unintentional operation of the

device. Make sure that the switch is in

the “OFF” position before you insert

the mains plug into the mains socket.

Accidents can happen if you carry the device

with your ﬁnger on the switch or you have

already switched the device on before you

connect it to the mains.

d) Remove any setting tools or spanners

before you switch the device on. A

tool or spanner left attached to a rotating part

of a device can lead to injury.

e) Do not overestimate your own abili-

ties. Keep proper footing and balance

at all times. By doing this you will be in a

better position to control the device, especially

in unforeseen circumstances.

f) Wear suitable clothing.

Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and

gloves clear of moving parts. Loose

clothing, jewellery or long hair can become

trapped in moving parts.

4. Use and handling of the

electrical power tool

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

9 GB/IE/CY

General safety advice / Advice on use

b) Do not use an electrical power tool if

its switch is defective. An electrical

power tool that can no longer be switched on

and oﬀ is dangerous and must be repaired.

c) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use the device if he or she is not famil-

iar with it or has not read the instruc-

tions and advice.

Electrical power tools are dangerous when

they are used by inexperienced people.

d) Look after the device carefully.

Check that moving parts are working

properly and move freely. Check for

any parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

e) Use the electrical power tool, acces-

sories, inserted tools etc. in accordance

with these instructions and advice,

and the stipulations drawn up for this

particular type of device. In doing

this, take into account the working

conditions and the task in hand. The

use of electrical power tools for purposes other

than those intended can lead to dangerous

situations.

Safety advice relating spe-

ciﬁcally to paint spray guns

J Wear a breathing/dust mask!

The inhalation of paint mist and sol-

vent vapour is hazardous to health.

J Work in adequately ventilated spaces only.

J If you do not know how dangerous a sub-

stance is, do not spray it.

J Never aim the spray at living creatures.

J

Danger of explosion! Do not

use the device in environments con-

taining gases, open ﬂames, ﬁres or

gas-operated water heaters.

J No smoking!

J Easily ﬂammable or explosive liquids (e.g.

petrol, spirit) must not be sprayed or used for

cleaning.

J Paint and solvents (thinners) must have a ﬂash-

point above 21°C.

J Precise observation of the hazard warnings,

information and data sheets available from the

sprayed medium manufacturer is essential.

Q

Advice on use

Q



DIN-sec / Viscosity

The Parkside paint spray gun PFSPS 150 can be

used to apply sprayed media with a viscosity up to

100 DIN-sec. Viscosity is determined in a simpliﬁed

measuring procedure using the supplied measuring

cup (see Fig. C).

1. Fill the measuring cup up to the rim with the

sprayed medium.

2. Measure how long in seconds it takes to ﬂow out.

3. This time is the DIN-seconds value of viscosity.

Q



Preparing the sprayed medium

Most paints, varnishes etc. in the shops are intended

to be applied by brush not spray. To achieve the

best spraying result, you should prepare your paint

or varnish etc. in accordance with DIN guidelines

to achieve a suitable viscosity (see table).

Use a suitable thinner to achieve the required

thinning of the medium.

1. Thoroughly mix through unthinned sprayed

medium at 20 °C.

2. Add a suitable thinner.

3. Test the viscosity as described above, see Fig. C.

Note: Never use nitro-thinners to thin synthetic

resin paint!

10 GB/IE/CY

Example of

material

DIN guidance

value

Car body paint 16-20 DIN-sec

Acrylic paint 25-30 DIN-sec

Synthetic resin paint 25-30 DIN-sec

Primer 25-30 DIN-sec

Q

Switching On/Oﬀ

Switching on

j To start the device, press the ON/OFF switch

3

and keep it pressed.

Switching off

j To switch oﬀ the device, release the ON/OFF

switch

3

.

Q

Spraying process

The surface to be sprayed must be clean, dry and

free of grease.

Observe the safety advice!

1. You can vary the spray by adjusting the regulator

button

2

(see Fig. D). The spray is correctly

set when no drops are formed and the gun

produces a ﬁne, consistent spray pattern.

2. Do not switch the device on or oﬀ over the

area being sprayed. Begin and end the spray

process approx. 10 cm beyond the area being

sprayed.

3. The spray process should follow the sequence

shown in Fig. E – keep the spray gun moving

parallel to the surface

– Do not incline the spray gun

– Move the spray gun at a constant speed

– Apply the sprayed medium as thinly as possible

– The layer(s) of sprayed medium need(s) to

be allowed to dry for some time before you

apply the next coat Fig. F) at right angles to

the previous coat.

4. Do not allow the paint cup to empty complete-

ly while spraying – drops may form!

Q

Maintenance and cleaning

General advice

1.

WARNING!

Pull out the mains plug be-

fore you carry out any tasks on the spray gun.

Do the same when you take a break from spraying.

2. After each use, spray thinners (in the open

air only – danger of explosion!) or

water through the device.

3. To protect from rust after cleaning, you can

spray sewing machine oil through the device.

4.

WARNING!

Never immerse the device

in the cleaning medium.

5. Never use inﬂammable solvents to clean the

device.

Cleaning instructions

1. Unscrew the attachment screw

1

, see Fig. A.

2. Take oﬀ the pump housing

10

downwards.

3. Unscrew nozzle

8

and remove the suction-

pressure valve

9

.

4. Take the pump piston

4

and spring

5

out of

the pump housing

10

.

5. Clean parts

4

,

5

,

8

,

9

with thinners.

6. Fit the components back in reverse order.

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electrical

power tools with the household

rubbish!

In accordance with European Directive 2002 / 96 / EC

(covering waste electrical and electronic equipment)

and its transposition into national legislation, worn

out electrical power tools must be collected separately

and taken for environmentally compatible recycling.

Contact your local refuse disposal authority for

more details of how to dispose of your worn out

electrical devices.

Advice on use / Maintenance and cleaning / Disposal

11 GB/IE/CY

Environmental compatibility and

disposal of materials

j Paint, varnishes etc. are special wastes which

must be disposed of in the appropriate manner.

j Observe the regulations applicable in your area.

j Observe the manufacturer’s instructions.

j Environmentally damaging chemicals must not

be allowed to enter the soil, groundwater or

watercourses.

j Carrying out spraying at the edge of water-

courses or adjoining areas (catchments) is

therefore prohibited.

j Consider their environmental compatibility

when buying paints, varnishes etc.

Q

 Information

Q

Service centre

The service centre for your country is shown in the

warranty documentation.

WARNING!

Have your device

repaired only by qualified specialist

personnel using original manufactur-

er parts only. This will ensure that your

device remains safe to use.

WARNING!

If the plug or mains lead

needs to be

replaced, always have the

replacement

carried out by the manu-

facturer or its service centre. This will

ensure that your device remains safe to use.

Q

Declaration of Conformity /

Manufacturer

We, Kompernaß GmbH, Burgstr. 21,

44867 Bochum, Germany, declare that this

product complies with the following EU directives:

Machinery Directive (98 / 37 / EC)

EU Low Voltage Directive (2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

Type / Machine designation:

Paint spray gun PFSPS 150

Bochum, 30.04.2008

Hans Kompernaß

- Managing Director -

We reserve the right to make technical modiﬁcations in the course

of product development.

Disposal / Information

Page is loading ...

Parkside PFSPS150 User manual

This manual is also suitable for

Parkside PFSPS150 User manual

in other languages

Related papers

Other documents