Crux DKFD-60L User manual

Brand: Crux

Model: DKFD-60L

Type: User manual

Crux DKFD-60L is a radio replacement interface with steering wheel control retention and dash kit, compatible with Ford, Lincoln, and Mercury vehicles. It enables the user to replace the factory radio with an aftermarket one while retaining the original steering wheel controls and other factory features. The device also includes a dash kit to ensure a seamless and professional-looking installation. Note that the DKFD-60L supports analog steering wheel control signals and provides outputs for reverse gear, illumination, and speed signal.

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

DKFD-60L

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

1 of 7

- Retains factory features with an aermarket radio.

- Retains factory-installed Subwoofer.

- Retains Steering Wheel Controls via built-in, pre-programmed interface.

- With navigaon outputs (Reverse gear, Illuminaon and Speed signal).

- Provides Accessory Power (2A MAX).

- Includes dask kit (double DIN or single DIN with pocket).

PRODUCT FEATURES:

PARTS INCLUDED:

SWRFD-60L MODULE SWRFD-60L HARNESS Antenna Adapter SWC CABLE SWC 3.5MM PLUG ADAPTER

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

DKFD-60L

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

2 of 7

INSTALLATION DIAGRAM:

AFTERMARKET

RADIO

+12V Constant Yellow

+12V ACC Red

12V Ground Black

Illumination Orange

Vehicle Speed Sense Red/White (or Brown)

Subwoofer Amp Turn-on Blue/White

Antenna Turn-on Blue

Right Front (+) Gray

Right Front (-) Gray/Black

Left Front (+) White

Left Front (-) White/Black

Right Rear (+) Violet

Right Rear (-) Violet/Black

Left Rear (+) Green

Left Rear (-) Green/Black

Subwoofer

Factory Aux Input

24-Pin

Plug*

16-Pin

Plug*

8-Pin

Plug*

TO FACTORY

HARNESS

12-Pin

Connector

SWC TYPE

(Connect PINK to PINK wire)

Subwoofer

Converter

Module

*Inspect that the male pins are

properly lined up before plugging

into the factory harness.

SWRFD-60L

MODULE

ON RADIO VEHICLE

1 2 3 4 5 6 7 8

AFTERMARKET

RADIO SELECTOR

(See Chart)

FORD

SWC SETTING

(OFF OFF OFF OFF)

ON RADIO VEHICLE

1 2 3 4 5 6 7 8

Cap or insulate if

not being used

Kenwood/JVC (BLUE / YELLOW)

Insulate with tape

if not being used

3.5MM SWC CABLE

Plug in the 3.5MM SWC cable to the 4-pin port

on the module. See “DIP SWITCH SETTINGS” section.

LIN BUS (Green)

Blue/Yellow

(Not Used)

1. Only supports analog Steering Wheel Control type.

2. Use part number SWRFD-60 for CAN Bus Steering Wheel Control.

3. Output signal stated above may not cover all Year/Model.

4. Does not retain SYNC.

5. Not compable with factory-installed Sony systems and THX systems with amplier.

NOTES:

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

3 of 7

DKFD-60L

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

ANALOG CONNECTION:

WIRE VIEW

PINK BLACK

Crux 24-Pin Connector

HOW TO DETERMINE IF THE VEHICLE HAS ANALOG SWC:

Analog Steering Wheel Control (SWC) signal vehicles will have

wires populated and line up to the PINK and BLACK wire on the

24-Pin Crux connector.

If one wire is missing then you will need to use Crux part number

SWRFD-60.

DIP SWITCH SETTINGS:

FORD STEERING WHEEL CONTROL DIP SWITCH SETTING:

RED to SWC Key 1

WHITE to SWC Key 2

SHIELD to SWC Ground

(included in kit)

AFTERMARKET RADIO DIP SWITCH SETTINGS:

SWC 3.5MM PLUG ADAPTER:

Use the supplied 3.5MM SWC Plug adapter for aermarket radios that do not have a 3.5mm SWC jack.

RADIO BRAND: DIP: 1 2 3 4

Dual, Fahrenheit, Jensen, Pioneer

Power Acoustik, Soundstream

Alpine

Clarion

Kenwood

JVC

Boss, Old Sony

New Sony

OFF OFF ON ON

OFF OFF OFF OFF

OFF ON ON OFF

OFF ON ON ON

OFF ON OFF ON

OFF ON OFF OFF

OFF OFF ON OFF

SWC MODULE

ON RADIO VEHICLE

1 2 3 4 5 6 7 8

DIP: 5 6 7 8

Ford OFF OFF OFF OFF

SWRFD-60L

SWC MODULE

ON RADIO VEHICLE

1 2 3 4 5 6 7 8

NOTE: Insulate the Blue/Yellow and Green wires if not being used.

3.5MM SWC CABLE

Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

4 of 7

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

DKFD-60L

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

VEHICLE APPLICATIONS:

FORD

2007 – 2010 Edge

2008 – 2012 Escape**

2007 – 2010 Expedion

2006 – 2010 Explorer

2007 – 2010 Explorer Sport Trac

2009 – 2008 F-150

2009 – 2012 F-150*

2008 – 2012 F-Series Super Duty

2005 – 2007 Five Hundred

2007 – 2008 Focus

2004 – 2007 Freestar

2005 – 2007 Freestyle

2006 – 2009 Fusion

2005 – 2009 Mustang

2008 – 2009 Taurus

LINCOLN

2006 – 2008 Mark LT

2007 – 2010 MKX (Nav only)

2007 – 2011 Navigator (Nav only)

MERCURY

2008 – 2010 Mariner**

2006 – 2009 Milan

2005 – 2007 Montego

2004 – 2007 Monterey

2006 – 2010 Mountaineer

2008 – 2009 Sable

MAZDA

2009 – 2011 Tribute**

*Not compable on vehicles equipped with acclimated radio/climate control panel.

**Compable with vehicles equipped with factory navigaon radio only.

Compable Ford SWC Types:

Type 1

4-Buon

Type 2

4-Buon

Type 3

5-Buon

Type 4

6-Buon

DKFD-60L

1. Insert IS O brackets to rear of kit as shown in F igure A

2. Insert pocket into lower section of kit from rear & lock into s lots of mounting brackets .

3. Insert IS O mountable radio between IS O mount brackets and loos ely attach to sides

of radio us ing screws provided with radio when pos s ible or s crews supplied with kit.

4. S lide radio forward or backward for desired look and tighten s crews.

5. Attach a rear support bracket to the rear of the new radio and adjust as neces s ary

to s upport the weight of the radio (Optional)

SINGLE ISO MOUNT INSTALLATION INSTRUCTIONS

Fig. A

Fig. B

1. Attach left and right mounting brackets to the kit as s hown in the figure below.

2. Insert IS O mountable radio between IS O mount brackets and loos ely attach to

sides of radio using screws provided with radio when pos sible

or s crews supplied with kit.

3. S lide radio forward or backward for desired look and tighten s crews.

4. S upport the rear of the radio component with back strap (optional).

DOUBLE DIN MOUNT INSTALLATION INSTRUCTIONS

Remove shaded tabs

on left and right sides

of the brackets

(Right side not shown)

Fig. D

Fig. E

Fig. C

FOR FIGUR E D

REMOVE SHADED

MOUNTING TABS ON

BOTH LEFT AND RIGHT

BRACKETS FOR :

FORD ESCAPE

MAZDA TRIBUTE

MERCURY MARINER

FOR FIGUR E E

REMOVE SHADED

MOUNTING TABS ON

BOTH LEFT AND RIGHT

BRACKETS FOR :

2009-14 FORD F-150

FOR FIGUR E C

REMOVE SHADED MOUNTING

TABS ON BOTH LEFT AND

RIGHT BRACKETS FOR :

FORD EXPLORER

EXPLORER SPORT TRAC

FORD FUSION

LINCOLN ZEPHYR

MERCURY MILAN

MERCURY MOUNTAINEER

F or all vehicles listed below, remove the shaded mounting tabs on both

left and right brackets.

BRACKET PREPARATION

Fig. A

FOR FIGUR E A

REMOVE SHADED

MOUNTING TABS ON

BOTH LEFT AND RIGHT

BRACKETS FOR :

FORD 500

2004-08 FORD F-150

FORD FREESTYLE

FORD MUSTANG

FORD TRANSIT CONNECT

TAURUS/TAURUS X

MERCURY MONTEGO

LINCOLN MARK LT

Fig. B

FOR FIGUR E B

REMOVE SHADED

MOUNTING TABS ON

BOTH LEFT AND RIGHT

BRACKETS FOR :

FORD FREESTAR

FORD FOCUS

2005-08 FORD

SUPER DUTY

MERCURY MONTEREY

FOR FIGUR E F

REMOVE SHADED

MOUNTING TABS ON

BOTH LEFT AND RIGHT

BRACKETS FOR :

2009-15 FORD SUPER DUTY

Fig. F

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

5 of 7

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

6 of 7

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

DKFD-60L

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

NOTE: S ee illustration A on page 2 for bracket preparation

1. Open the s torage compartment located above the R adio/Vent trim bezel.

2. S tarting from the top edge and working your way down the s ides toward the bottom,

carefully pry the R adio/C limate control trim bezel forward, disconnect all harness es

from the rear of the trim bezel and remove bezel.

3. R emove the (4) 9/32 screws securing the radio to the sub-dash. C arefully pull

radio forward, disconnect all harnes ses and antenna lead and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2005-07 FORD FREESTYLE

NOTE: S ee illustration B on page 2 for bracket preparation

1. C arefully unclip and remove the radio/climate control trim bezel from around the

factory radio.

2. Disconnect the harness es from the rear of the radio/climate control bezel and

remove bezel.

3. R emove the (4) 9/32 screws securing the factory radio to the s ub-das h.

4. C arefully pull radio forward, disconnect the wire harnes s and antenna lead from the

factory radio and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2004-07 FORD FREESTAR

2004-07 MERCURY MONTEREY

NOTE: S ee illustration B on page 2 for bracket preparation

1. E ngage the parking brake.

2. F or Automatic Trans mis s ion Vehicles only, insert key into the ignition and turn to the

ON position and depress the brake pedal, (DO NO T S TAR T T HE VE HIC LE !) then

place the shift lever into the lowest position.

3. Lower the steering column all the way down.

4. S tarting at the top edge of the das h trim bezel, carefully unclip and pull forward the

dash trim bezel to acces s all the wire harnes s connectors attached to the features

on the rear of the trim bezel.

5. C arefully disconnect all the connectors on the back side of the das h trim bezel and

remove bezel.

6. R emove the (4) 9/32 screws securing the radio to the sub-dash.

7. C arefully pull radio forward, disconnect the wire harnes ses and antenna lead from

the rear of the radio and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2005-08 FORD Super Duty

NOTE: S ee illustration B on page 2 for bracket preparation

1. C arefully pry forward and unclip R adio/C limate control trim bezel and dis connect

the 12 Volt R eceptacle plug from the rear of the bezel.

2. Lay the trim bezel as sembly out of the way (Disconnecting the climate control cables

or harnes ses is not necess ary).

3. R emove the (4) 9/32 screws securing the radio to the sub-dash.

4. C arefully pull F actory radio forward, disconnect the wire harnes s and antenna lead

from the rear of the radio and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2005-07 FORD FOCUS

NOTE: S ee illustration A on page 2 for bracket preparation

1. C arefully remove the trim from around the gearshift.

2. R emove the (2) Phillips s crews located under the center cons ole lid.

3. Lift up on the emergency brake and carefully remove the center console.

4. C arefully unclip and remove the trim panels at the left and right side of the radio.

5. R emove the (4) 9/32 screws securing the radio trim bezel to the sub-dash, carefully

pull trim bezel forward, disconnect all attached harnes ses and remove trim bezel.

6. R emove the (4) 9/32 screws securing the radio to the sub-dash, carefully pull radio

forward and disconnect all harnes s es and antenna lead and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2005-09 FORD MUSTANG

NOTE: S ee illustration C on page 2 for bracket preparation

1. Open the center console and remove the (2) 9/32 screws from the center console

shifter trim.

2. C arefully lift up on the center console shifter trim and disconnect the 12 volt

receptacle harness and remove trim.

3. C arefully pry outward on the radio trim bezel to release the panel clips, then lift the

lower s ides upward and s lightly outward to clear the shift lever.

4. Disconnect all harness es from the radio trim bezel and remove bezel.

5. R emove the (4) 9/32 screws securing the radio to the sub-dash.

6. P ull radio forward, disconnect all harnes ses and antenna lead and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2006-10 FORD EXPLORER

2006-10 MERCURY MOUNTAINEER (NAV ONLY)

2007-10 EXPLORER SPORT TRAC

NOTE: S ee illustration C on page 2 for bracket preparation

1. S tarting from the bottom, carefully pry the factory radio trim bezel from around the

radio forward, disconnect all harnes ses attached to the rear of the trim bezel and

remove bezel.

2. R emove the (4) 9/32 screws securing the radio to the sub-dash.

3. C arefully pull radio forward, disconnect all harness es and antenna lead and

remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2006-09 FORD FUSION

2006-08 LINCOLN ZEPHYR

2006-09 MERCURY MILAN

DASH DISASSEMBLY INSTRUCTIONS

2008-11 FORD ESCAPE

2008-11 MAZDA TRIBUTE/ MERCURY MARINER

NOTE: S ee illustration D on page 2 for bracket preparation

1. C arefully pry the Vent ass embly above the radio forward.

2. R emove the (2) 9/32 screws securing the top of the radio/C limate control ass embly to

the s ub-dash.

3. C arefully pry the LOW E R 12 Volt/ US B / Auxiliary plug panel forward, disconnect all

attached harnesses and remove panel.

4. R emove the (2) 9/32 screws securing the lower edge of the R adio/C limate control

as sembly.

5. S et the parking brake.

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.051619

7 of 7

RADIO REPLACEMENT

SWC RETENTION

+ +

INTERFACING SOLUTIONS

DKFD-60L

Radio Replacement Interface with Steering Wheel Control Retention

with Dash Kit for FORD, LINCOLN & MERCURY

6. R emove the shift lock cover and pres s the shift lock button down using a s mall

screwdriver or pen and depres s the brake pedal and move the shift lever

all the way to the rear.

7. C arefully pull the entire R adio/C limate control ass embly forward (you will need a

second person for the next step). B e careful not to scratch the s ides of the das h,

or the s hift lever.

8. R emove the (1) 5/16 bolt securing the G round strap to the right s ide of the

as sembly. P liers may be neces sary due to the s hort length of the strap.

9. P ull the entire ass embly forward and remove all attached harnes ses and antenna

leads and remove as s embly.

10. R emove the (4) 9/32 screws from the sub-dash to be able to mount the ins tall kit

into the das h location.

NOTE: S ee illustration E on page 2 for bracket preparation

1. Open the ashtray/pocket below the climate controls.

2. F rom behind the auxiliary panel located to the right of the cigarette lighter, carefully

unclip and press the auxiliary panel forward to release, disconnect the attached

harnes ses(if applicable) and remove panel.(save for re-as sembly)

3. R emove the (1) 9/32 screw securing the lower edge of the radio/climate control trim bezel.

4. R emove the rubber mat located above the top edge of the radio trim bezel or fascia.

5. R emove the (2) 9/32 screws located under this mat.

6. Us ing a panel removal tool, carefully pry the left and right vent trim panels slightly

outward to allow the edges of the F ascia of the R adio/C limate control bezel to be

removed, (it is not necessary to remove the vent trims entirely).

7. C arefully unclip and remove the factory radio/climate control bezel, or fas cia.

8. R emove the (4) 9/32 screws securing the radio (or radio sub-chassis) to the sub-dash.

9. C arefully pull the radio forward, disconnect all attached harness es and antenna lead

and remove radio (or radio sub-chass is).

(Center Console shift Vehicles)

1. S et the P arking B ra ke.

2. Open the center console armrest lid and remove the (3) lower Torx screws securing

the lid/hinge ass embly to the pocket cavity of the center console.

3. C arefully unclip and remove the thin panel below the cigarette lighter.

4. F rom behind the auxiliary panel located to the right of the cigarette lighter, carefully

unclip and press the auxiliary panel forward to releas e, disconnect the attached

harnes ses(if applicable) and remove panel.(save for re-as sembly)

5. R emove the (1) 9/32 screw securing the lower edge of the radio/climate control trim bezel.

6. R emove the rubber mat located above the top edge of the radio fas cia.

7. R emove the (2) 9/32 s crews located under this mat.

8. Insert key into the ignition and turn to the O N pos ition, (DO NOT S TAR T the vehicle).

9. Depress the brake pedal and move the shift lever back.

10. Lift up and remove the shift trim/drink holder as sembly.

11. Starting from the rear top edge of the center console, carefully lift up and unclip the entire top

trim section that meets the lower edges of the C enter S tack Vent/radio side trim panels.

12. Using a panel removal tool, carefully pry the left and right vent trim panels s lightly

outward to allow the edges of the F as cia of the R adio/C limate control bezel to be

removed, (it is not necessary to remove the vent trims entirely).

13. C arefully unclip and remove the factory radio/climate control bezel, or fas cia.

14. R emove the (4) 9/32 screws s ecuring the radio (or radio sub-chassis) to the sub-dash.

15. C arefully pull the radio forward, disconnect all attached harness es and antenna lead

and remove radio (or radio sub-chass is).

DASH DISASSEMBLY INSTRUCTIONS

2009-12 FORD F-150 / 2013-14 FORD F-150 (with Classic Dash)

DASH DISASSEMBLY INSTRUCTIONS

2009-15 FORD SUPER DUTY PICKUP

NOTE: S ee illustration F on page 2 for bracket preparation

1. Us ing a F lat blade screwdriver, insert the s crewdriver blade into the slots located on

the bottom edges of each the 12 Volt receptacle and S ync panels located below and

to the sides of the factory climate controls, gently pull each panel forward to release

and rest out of the way.

2. R emove the individual 9/32 screw located behind each panel removed in step 1 above.

3. C arefully pull the entire R adio/C limate C ontrol panel with Vents forward to releas e

and rest out of the way.

4. R emove the (4) 9/32 screws securing the radio to the sub-dash.

5. C arefully pull the radio forward, disconnect the attached wire harnesses and antenna

adapter and remove radio.

NOTE: S ee illustration A on page 2 for bracket preparation

1. C arefully P ry radio dash trim bezel outward, disconnect all harnesses from back of

trim bezel and remove bezel.

2. R emove the (4) 9/32 screws s ecuring the factory radio to the s ub-das h.

3. P ull radio forward, disconnect all harness es and antenna lead and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2004-08 FORD F-150 (EXCLUDES HERITAGE MODELS)

2006-07 LINCOLN MARK LT

2012-2013 Transit Connect

NOTE: S ee illustration A on page 2 for bracket preparation

1. C arefully P ry radio dash trim bezel outward, disconnect all harnesses from back of

trim bezel and remove bezel.

2. R emove the (4) 9/32 screws securing the factory radio to the sub-dash.

3. P ull radio forward, disconnect all harness es and antenna lead and remove radio.

DASH DISASSEMBLY INSTRUCTIONS

2005-07 FORD 500

2005-07 MERCURY MONTEGO

2008-09 TAURUS/TAURUS X

Crux DKFD-60L User manual

Brand: Crux

Model: DKFD-60L

Type: User manual

Download PDF

report

Crux DKFD-60L User manual

Crux DKFD-60L User manual

Related papers

Other documents