Bosch MESM731MIN/01 Operating instructions
- Category
- Juice makers
- Type
- Operating instructions
Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
MESM5... MESM7...
VitaExtract Slow juicer
[en] Instruction manual Slow juicer 6
1
3
5*
29 10
4
6
8
7
11
12
a
e*
c
d
a
a
h
d
f *
b
c
ba
b
b
g
c a
e*
f
A
B C
1
2
3
4
5
6
1
2
3
4
5
ON
ON
OFF
y
10–20
min
D
567
1
2 3 4
1
32 4
5
8
E
F
G
H
1
2 3
I
6
en Intended use
Intended use
This appliance is intended for domestic use only.
The appliance is suitable for squeezing fresh juice from fruit or
vegetables. The appliance is suitable for making sorbet from frozen
fruit or vegetables when using the sorbet insert piece. The appliance
must not be used for processing other substances or objects.
Additional applications are possible if the accessories approved by
the manufacturer are used. Only use the appliance with approved
genuine parts and accessories. Never use the accessory parts for
other appliances.
Only use the appliance indoors at room temperature and up to
2000 m above sea level.
Important safety information
Read and follow the instruction manual carefully and keep for later
reference! Enclose these instructions when you give this appliance
to someone else. If the instructions for correct use of the appliance
are not observed, the manufacturer’s liability for any resulting
damage will be excluded.
This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and/or
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved. Keep children away from the
appliance and connecting cable and do not allow them to use the
appliance. Children shall not play with the appliance. Cleaning and
user maintenance must not be made by children.
WRisk of electric shock and fire!
■Connect and operate the appliance only in accordance with the
specifications on the rating plate. Do not use the appliance if the
power cord and/or appliance are damaged. Only our customer
service may repair the appliance, e.g. by replacing a damaged
power cord, in order to avoid hazards.
■Never connect the appliance to timer switches or remote-
controllable sockets. Never leave the appliance unattended while
it is switched on!
■Do not place the appliance on or near hot surfaces, e.g. hobs.
The power cord must not come into contact with hot parts or be
pulled across sharp edges.
■Never immerse the base unit in water or place it in the
dishwasher. Do not steam-clean the appliance. Do not use the
appliance with damp hands.
7
en
Important safety information
Congratulations on the purchase of
your new Bosch appliance. You can find
further information about our products
on our website.
■After each use, whenever the appliance is unsupervised, prior to
assembly, prior to disassembly, prior to cleaning and in the event
of an error, the appliance must always be disconnected from the
mains.
WRisk of injury!
■Before replacing accessories or additional parts which move
during operation, the appliance must be switched off and
disconnected from the power supply. Immediately after using the
appliance, wait for it to stop.
■Only operate the appliance in its fully assembled state. Never
operate it without a correctly placed and locked lid!
■Never reach into the feed chute with your hands during operation.
Do not insert any objects (e.g. wooden spoons) into the feed
chute. Only use the pusher provided!
■Keep hands clear of rotating parts. Use the appliance only with
genuine parts and accessories.
WRisk of suffocation!
Do not allow children to play with packaging material.
WCaution!
We recommend that the appliance is never switched on for longer
than is necessary to process the ingredients. Do not operate
at no-load.
WImportant!
It is essential to clean the appliance thoroughly after each use or
after it has not been used for an extended period. X “Cleaning” see
page 11
Contents
Intended use ............................................... 6
Important safety information .......................6
Overview.....................................................8
Before using for the first time......................8
Symbols and markings ...............................8
Adjusting lever / seal for fruit pulp ..............9
Preparation .................................................9
Use ...........................................................10
Cleaning ................................................... 11
Disposal .................................................... 12
Guarantee.................................................12
Troubleshooting ........................................ 13
8
en Overview
Before using for the
first time
Before the new appliance can be used,
it must be fully unpacked, cleaned and
checked.
Caution!
Never operate a damaged appliance!
■Remove the base unit and all accesso-
ries from the packaging and dispose of
all packing materials.
■Check that all the parts are present and
examine them for obvious damage.
X Fig. A
■Thoroughly clean and dry all parts
before using for the first time.
X “Cleaning” see page 11
Symbols and markings
Symbol Meaning
KFit the lid (,) and screw
on securely (;).
GMarking on the base unit for
fitting the lid and for the insert
pieces.
HMarking on the insert pieces.
FFit juice drum (.).
EMarking on the base unit for
fitting the juice drum.
Max. capacity. If the juice
reaches the 350 ml marking,
finish processing and empty
the juice drum.
È É Ê *
Markings on the juice drum
for the adjusting lever *:
cleaning, little fruit pulp, lot of
fruit pulp.
Overview
X Fig. A
1 Base unit/motor unit
a Drive shaft
b Marking G
c Switch (3-level)
ON = On
y = Off
{= Reversing function
d Mains cable
e LED-Ring*
f Marking ö
2 Juice drum
a Seal for drive shaft
b Aperture for juice
c Sealing cap for juice (drip-stop)
d Aperture for fruit pulp
e Adjusting lever with seal for fruit pulp
and markings È É Ê *
f Seal for fruit pulp*
g Marking F
h Scale
3 Rotating brush with silicon scraper
4 Strainer insert pieces
a Fine (black)
b Coarse (grey)
c Marking Å
5 Sorbet insert piece*
a Marking Å
6 Juicer screw
7 Pusher
8 Lid
a Feed chute
b Marking K
9 Container for juice
10 Container for fruit pulp
11 Cleaning brush
12 Recipe book
* Depending on the model
9
en
Adjusting lever / seal for fruit pulp
Adjusting lever /
seal for fruit pulp
X Fig. F – Models with adjusting lever
for seal
The consistency of the juice can be
controlled using the adjusting lever for fruit
pulp.
■For juice with a lot of fruit pulp, slide the
lever to the right (Ê).
■For juice with less fruit pulp, slide the
lever towards the centre (É).
■To clean/rinse out, remove the juice
drum, turn over and slide the lever to the
stop as shown (È).
X Fig. G – Models with seal
The seal for fruit pulp ensures that the juice
has a constant consistency.
■When making juice or sorbet, the seal
must sit correctly in the aperture for fruit
pulp.
■To clean/rinse out, remove the juice
drum, turn over and pull out the seal.
Preparation
W Risk of injury
Do not insert the mains plug until all
preparations for working with the appliance
are complete and all individual parts are
assembled correctly and connected to the
base unit.
Caution!
Never place the juice drum onto the base
unit without the seal for the drive shaft.
Ensure that the seal also sits correctly after
placing it onto the base unit.
Important: Before re-assembling, check
that the aperture is completely closed by
the seal for fruit pulp. X “Adjusting lever /
seal for fruit pulp” see page 9
Preparing to squeeze juice
X Image sequence B
1. Place the base unit onto a stable and
level work surface.
2. Place the juice drum onto the base
unit. When doing so, align the recesses
on the base of the juice drum with the
counterparts on the base unit (observe
. markings). The juice drum must sit
flush and firmly on top of the base unit.
3. Place the rotating brush into the juice
drum.
4. Place the desired strainer insert piece
(coarse or fine) into the rotating brush
(observe markings .).
Important: Ensure that the aperture and
the notches on the base sit firmly on top of
their counterparts on the juice drum. The
strainer insert piece must not be able to turn
any further.
5. Place the juicer screw into the strainer
and press down until it sits on top of the
drive shaft.
6. Place the lid on top (,) and turn
it as far as possible in a clockwise
direction (;).
Preparing to make sorbet
X Image sequence C
1. Place the base unit onto a stable and
level work surface.
2. Place the juice drum onto the base
unit. When doing so, align the recesses
on the base of the juice drum with the
counterparts on the base unit (observe
. markings). The juice drum must sit
flush and firmly on top of the base unit.
3. Place the sorbet insert piece in the juice
drum (observe markings . ).
Important: Ensure that the aperture and
the notches on the base sit firmly on top of
their counterparts on the juice drum. The
sorbet insert piece must not be able to turn
any further.
4. Place the juicer screw into the sorbet
insert piece and press down until it sits
on top of the drive shaft.
5. Place the lid on top (,) and turn
it as far as possible in a clockwise
direction (;).
10
en Use
Preparing food
Important: Only process ripe fruit and
vegetables. Unripe or over-ripe fruit will very
quickly clog the juicer screw and its strainer.
■Remove stones or seeds (e.g. for
plums, peaches, cherries etc.).
■Remove hard peel/skin (e.g. for melons,
pineapples, cucumbers, potatoes etc.).
■Fruits and vegetables with thin peel/skin
(e.g. apples, pears, carrots, radishes,
salad, cabbages, parsley, spinach,
grapes, strawberries, celery etc.) only
need to be washed.
■Peel citrus fruits and remove the white
pith, as the juice may taste bitter
otherwise.
■Chop up large fruits and vegetables
beforehand so they fit into the feed
chute without having to force them in.
Use
W Risk of injury
– Only operate the appliance in its fully
assembled state.
– Never operate it without a correctly
placed and locked lid.
– Do not reach into the feed chute with your
fingers. Use the supplied pusher only!
Caution!
Always use the sorbet insert piece to process
frozen fruits. Do not process fruit that gets
very hard by freezing (eg. strawberries).
Important: If the juice reaches the 350 ml
marking, finish processing and empty the
juice drum.
Squeezing juice
X Image sequence D
■Prepare the appliance as described.
X “Preparing to squeeze juice” see
page 9
1. Place one container under each of the
apertures for juice and fruit pulp.
2. Open the sealing cap for the juice.
3. Slide the adjusting lever for fruit pulp
(depending on the model) as wished
either towards the centre (É) or all the
way to the right (Ê).
4. Plug the mains plug into the mains.
Move the switch to ON. The appliance
starts. The LED ring lights up (depend-
ing on the model). The rotating brush
rotates.
5. Add the prepared food to the feed chute.
6. Only use the pusher provided to push
the food further. The juice flows into the
right-hand container. The squeezed fruit
pulp will be collected in the left-hand
container.
7. Once the processing is complete or the
juice container is full, move the switch
to O and wait for the appliance to come
to a stop.
8. Close the sealing cap for the juice and
empty the container.
Notes:
– To improve the amount of juice pro-
duced, preferably process ingredients
containing lots of juice at the beginning
and end of processing (e.g. oranges,
tomatoes, watermelon, etc.). Process
hard or fibrous Ingredients in-between.
– Fill the food into the feed chute one
portion at a time.
– Stuffing it in excessively does not
accelerate the processing and leads to
the drum overflowing.
Making sorbet
X Image sequence E
1. Prepare the appliance as described with
the sorbet insert piece. X “Preparing to
make sorbet” see page 9
Place a container under the aperture for
the juice. Open the sealing cap for the
juice.
2. Plug the mains plug into the mains.
Move the switch to ON. The appliance
starts. The LED ring lights up (depend-
ing on the model).
3. Add the frozen food to the feed chute.
11
en
Cleaning
4. Only use the pusher provided to push
the food further. The sorbet produced
will be collected in the container.
Reversing function
The reversing function is designed to
release food that has got stuck by briefly
running the worm gear in reverse.
■Move the switch to O and wait for the
appliance to come to a stop.
■Move the switch to { and keep it
pressed.
■After approx. 3-5 seconds, release the
switch and wait for the appliance to
come to a stop.
■Move the switch to ON and continue
with the juicing.
Note: If food that has got stuck is not
released by briefly putting the appliance into
reverse, switch the appliance off, unplug it
and clean it. X “Cleaning” see page 11
Warning!
The reversing function must be used for
several seconds or it will no longer be pos-
sible to switch on the appliance.
After using the appliance
■Empty both containers and then place
them under the apertures for juice and
fruit pulp again.
■Close the sealing cap and slide the
adjusting lever for the fruit pulp all the
way to the right.
■Pour a little water (approx. 150 ml) into
the feed chute and move the switch
to ON.
■After a short time, open the sealing cap
and slide the adjusting lever for fruit pulp
all the way to the left.
■Let the appliance slow down and stop
completely before switching it off.
■Move the switch to O and wait for the
appliance to come to a stop.
■Disconnect the mains plug.
■Clean all parts immediately after use.
Cleaning
The appliance and the individual parts used
must be thoroughly cleaned after each use.
W Risk of electric shock!
– Unplug the appliance before cleaning it.
– Never immerse the base unit in liquids
and do not clean in the dishwasher.
– Do not steam-clean the appliance.
Caution!
– Do not use any cleaning agents
containing alcohol or spirits.
– Do not use any sharp, pointed or metal
objects.
– Do not use abrasive cloths or cleaning
agents.
– Do not clean the individual parts in the
dishwasher.
Notes:
– When processing food such as carrots,
plastic parts may become discoloured.
This can be removed with a few drops of
cooking oil.
– Completely open the seal for fruit pulp.
X “Adjusting lever / seal for fruit pulp”
see page 9
In Fig. H you will find a summary of how to
clean the individual parts.
Dismantling the appliance
■Rotate the lid to the marking (,) and
remove.
■Remove the assembled juice drum.
■Then dismantle the juicer screw, strainer
or sorbet insert piece and the rotating
brush one by one.
Note: If the individual parts in the juice
drum are jammed (e.g. due to remnants of
fruit), proceed as follows.
X Image sequence I
1. Turn the juice drum over, putting a cloth
underneath.
2. On the underside carefully press on the
drive shaft of the juicer screw until it
releases.
3. Remove all individual parts.
12
en Disposal
Cleaning the base unit
■Wipe the outside of the base unit with a
soft, damp cloth and dry off.
Cleaning additional parts
■Clean the juice drum, rotating brush,
strainer insert pieces, sorbet insert
piece, juicer screw and pusher with
detergent solution, a soft cloth/sponge
and the brush provided or place them in
the dishwasher.
■The brush provided is particularly
suitable for thorough cleaning of the
apertures for juice and for fruit pulp.
■Clean the lid with detergent solution and
a soft cloth/sponge or a soft brush and
then rinse under running water.
■Leave all parts to dry or dry them off
with a cloth.
Disposal
J Save the environ ment - dispose your
e-waste in an environ
mentally friendly
manner by contacting designated
e-waste collection centers.
Please check our website
https://www.bosch-home.in/
for more details.
Guarantee
The guarantee conditions for this appliance
are as dened by our representative in the
country in which it is sold. Details regarding
these conditions can be obtained from
the dealer from whom the appliance was
purchased. The bill of sale or receipt must
be produced when making any claim under
the terms of this guarantee.
Changes reserved.
13
en
Troubleshooting
Troubleshooting
Problem Reason Remedy
The appliance
does not start when
switched on.
Appliance has no power supply. Insert the mains plug into the
socket.
The lid is not sitting correctly on
the juice drum.
Place the lid onto the juice drum
correctly. Observe the markings.
If the lid cannot be closed,
disassemble and reassemble
the parts again. Ensure that all
individual parts sit correctly.
The appliance stopped during
use.
The reversing function must
be used for several seconds or
it will no longer be possible to
switch on the appliance.
The appliance stops
during use.
Too much food to be squeezed
or hard seeds/stalks in the
appliance.
The reversing function must
be used for several seconds
or it will no longer be possible
to switch on the appliance.
X “Reversing function” see
page 11
The lid is not sitting correctly on
the juice drum.
Place the lid onto the juice drum
correctly.
The juice drum
cannot be positioned
on the base unit
correctly.
The adjusting lever for fruit
pulp is incorrectly adjusted or
the seal is not in the correct
position.
Check the setting/seal.
X “Adjusting lever / seal for fruit
pulp” see page 9
The juice is too
runny or too viscous.
The adjusting lever for fruit
pulp is incorrectly adjusted or
the seal is not in the correct
position.
Check the setting/seal.
X “Adjusting lever / seal for fruit
pulp” see page 9
Quantity in the appliance is too
large.
Do not process excessive
quantities simultaneously.
The appliance motor
is running loudly.
The appliance is incorrectly
assembled.
Disassemble and reassemble
the appliance as described.
X “Preparation” see page 9
If you are unable to solve the problem, always call the hotline!
You will find the telephone numbers at the back of these instructions.
1. This product is warrantied by the company
(warranty) to be free from defects in materials
and workmanship for a period of 2 years from
the date of purchase (warranty period)
2. This product is covered under warranty
against any manufacturing defect or
workmanship for a period of TWO YEARS
from the date of purchase. Should a defect
develop during the warranty period, Bosch
undertakes to repair the appliance FREE
OF CHARGE through any of the authorised
service centres.
3. Warranty and service:
For any information, grievances or queries
please contact our customer care helpline:
1 - 800 - 266 - 1880, or write to us at
[email protected]. The company
will register your service request and retain
a computer record of your service request.
To make a warranty claim, you must provide
proof of purchase.
4. CLAIM:
a. The claim must be made within the
warranty period.
b. Bosch will repair or replace any defective
parts and correct any problems resulting
from poor workmanship free of charge.
c. Service to the product shall be carried out
at your home or the store, whereby the
customer has to take the product to the
store where the product was purchased
at the purchaser’s risk, responsibility and
cost.
d. While the company will make every effort
to carry out the necessary repairs at the
earliest opportunity, the company is under
no obligation to do so within a stipulated
time period. Claims, if any, to this warranty
shall in no case exceed the purchase
price of the product.
e. In case of repairs or replacement of any
part(s) of the product, this warranty will
thereafter continue and remain in force
only for the unexpired period of the
warranty.
f. Replacement of parts would be purely at
the discretion of the company alone. If the
entire product is being replaced (subject
to the sole discretion of the company), the
same model will be replaced, and in the
event such model has been discontinued,
it shall be replaced with the model of
equivalent price at the time of purchase.
g. Replacement criteria from warranty
terms do not stand if “no problem found”
type diagnosis is made and perceived
intermittent errors that cannot be
reproduced are noticed.
h. The authorised technician concerned will
advise whether to effect repair on site or
at the authorised service centre.
i. This warranty will be terminated
automatically after a period of 24 months
from the date of purchase even if the
product was not in use for any time during
the warranty period for any reason.
5. This warranty shall be rendered null and void if:
a. The product is physically damaged
b. The product is modified, maintained or
repaired by a party not authorised by
Bosch.
c. The product is installed, maintained
and operated in ways other than as
recommended by Bosch.
d. The product is used for commercial
purposes.
e. The product is faulty or damaged due to
electrical faults external to the product.
f. Malfunctions or damage resulting from
insects, natural calamities, fire and/or
accidents.
g. The model number, serial number or
warranty stickers have been removed or
tampered with.
h. In case any spare part or any other part
is used in the functioning of the appliance
which does not comply with the safety
parameters approved by Bosch.
6. Warranty limitations
a. The warranty is not transferable from one
user/customer to another.
b. The Bosch warranty does not entail a
warranty of functionality or any obligation
to repair or replace a defective product
if that defect is a result of physical
breakage, improper installation or
connections, electrical faults external
to the product, misuse or unauthorised
modification of the product.
WARRANTY
1. This product is warrantied by the company
(warranty) to be free from defects in materials
and workmanship for a period of 2 years from
the date of purchase (warranty period)
2. This product is covered under warranty
against any manufacturing defect or
workmanship for a period of TWO YEARS
from the date of purchase. Should a defect
develop during the warranty period, Bosch
undertakes to repair the appliance FREE
OF CHARGE through any of the authorised
service centres.
3. Warranty and service:
For any information, grievances or queries
please contact our customer care helpline:
1 - 800 - 266 - 1880, or write to us at
[email protected]. The company
will register your service request and retain
a computer record of your service request.
To make a warranty claim, you must provide
proof of purchase.
4. CLAIM:
a. The claim must be made within the
warranty period.
b. Bosch will repair or replace any defective
parts and correct any problems resulting
from poor workmanship free of charge.
c. Service to the product shall be carried out
at your home or the store, whereby the
customer has to take the product to the
store where the product was purchased
at the purchaser’s risk, responsibility and
cost.
d. While the company will make every effort
to carry out the necessary repairs at the
earliest opportunity, the company is under
no obligation to do so within a stipulated
time period. Claims, if any, to this warranty
shall in no case exceed the purchase
price of the product.
e. In case of repairs or replacement of any
part(s) of the product, this warranty will
thereafter continue and remain in force
only for the unexpired period of the
warranty.
f. Replacement of parts would be purely at
the discretion of the company alone. If the
entire product is being replaced (subject
to the sole discretion of the company), the
same model will be replaced, and in the
event such model has been discontinued,
it shall be replaced with the model of
equivalent price at the time of purchase.
g. Replacement criteria from warranty
terms do not stand if “no problem found”
type diagnosis is made and perceived
intermittent errors that cannot be
reproduced are noticed.
h. The authorised technician concerned will
advise whether to effect repair on site or
at the authorised service centre.
i. This warranty will be terminated
automatically after a period of 24 months
from the date of purchase even if the
product was not in use for any time during
the warranty period for any reason.
5. This warranty shall be rendered null and void if:
a. The product is physically damaged
b. The product is modified, maintained or
repaired by a party not authorised by
Bosch.
c. The product is installed, maintained
and operated in ways other than as
recommended by Bosch.
d. The product is used for commercial
purposes.
e. The product is faulty or damaged due to
electrical faults external to the product.
f. Malfunctions or damage resulting from
insects, natural calamities, fire and/or
accidents.
g. The model number, serial number or
warranty stickers have been removed or
tampered with.
h. In case any spare part or any other part
is used in the functioning of the appliance
which does not comply with the safety
parameters approved by Bosch.
6. Warranty limitations
a. The warranty is not transferable from one
user/customer to another.
b. The Bosch warranty does not entail a
warranty of functionality or any obligation
to repair or replace a defective product
if that defect is a result of physical
breakage, improper installation or
connections, electrical faults external
to the product, misuse or unauthorised
modification of the product.
WARRANTY
WARRANTY CARD
Customer Service
Regardless of the nature of your concern, you can always
be sure of personal attention from the Bosch Customer
Service: on the internet and on the phone.
www.bosch-home.com/in
1 - 800 - 266 - 1880 (toll-free)
E-mail: ser[email protected]
Customer’s Name
Address
City Pin State
Telephone Mobile
E-mail Model/E-Nr
Serial No.
Date of Purchase Date of Expiry
Dealer’s Name
Dealer’s Signature and Stamp Customer’s Signature
Note: Warranty will start from the date of purchase.
BSH Household Appliances
Manufacturing Pvt. Ltd.
Arena House, 2nd Floor Main Building,
Plot No.103, Road No.12,
MIDC, Andheri East
Mumbai 400093
Toll Free 1 - 800 - 266 - 1880 *
www.bosch-home.com/in
* Mon-Sat: 8.00am to 8.00pm
(excluding public holidays)
8001197140
*8001197140*
(000507)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Bosch MESM731MIN/01 Operating instructions
- Category
- Juice makers
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Oscar JU-OS-1200-UL-AU-RD User manual
-
Stollar The Juice Presso BJP500 Operating instructions
-
Sencor SSJ 9000NP User manual
-
Omega NC800HDS User manual
-
-
Bella NutriPro User manual
-
Tribest FS-610 User manual
-
Omega J8006HDS User guide
-
Silvercrest SSJ 150 A2 Operating Instructions Manual
-
Catler JS 8010 User manual
