VIDEOMAN futuro-cm7 User manual

VIDEOMAN is a registered trade mark of EOS Australia Pty Ltd

Designed, imported and distributed by Videoman Systems Co.

•-IRON7M• • -CM7/CS7• • -7PS•

Wide Screen Monitor Doorstation Power Supply

Indoor Monitor FUTURO-IRON7M Installation guide FUTURO-CS7 Door Station Installation guide

Surface mount with optional FUTURO-IRON7WH

Fig.1 Fig.2

Install the door stations approx. 1.55M~1.60M from the ground Install the door stations approx. 1.55M~1.60M from the ground

Page 1

Remove front cover

FUTURO-CM7 Door Station installation guide FUTURO-CM7 Door Station installation guide

with optional weather hood FUTURO-CM7WH with optional flush mount FUTURO-CM7FM

Remove front cover

Fix a weather hood

Adjust camera

angle if necessary

Adjust camera

angle if necessary

Fix a FUTURO-CM7FM

into the wall

Pa

g

e

2

FUTURO-CM/CS7 Doorstation Installation Guide

I

Install the door stations about 1.55M~1.60M

from the ground.

Keep the units away from snow, rain and direct

sunlight.

FUTURO–IRON7C Door Station Installation and a Name Tag Holder assemble guide

1. Write desired name on the white plastic label provided.

2. Insert white plastic label into the clear plastic label holder.

3. Remove the front aluminum cover from the door station.

4. Insert the name tag holder into the black plastic from the back side

of the aluminum.

5. Install the door station back body to the wall.

6. Assemble the aluminum cover with 2 screws provided from the bottom of the doorstaion.

(Warning !! Be careful not to screw into a microphone hole)

Page 3

1

2

7

6

5

4

3

9

81011 12

13

14

Description of Monitor FUTURO-IRON7M features

1. SCREEN.

2. LED backlight.

3. TALK/OFF button.

When it rings it activates communication line

and also to turn the screen off.

4. DOOR OPEN/Changing Ring Tone button.

Press to open the entrance door during a

conversation.

When the monitor screen is off, press-and-hold

this button for 3 seconds to go into change ring

tone mode then press the MONITOR button to

select the ring tone. After selecting the ring

tone press the RING TONE button again to

exit.

5. MONITOR/SWITCH button.

Press to turn on the monitor manually.

When it is on, you can switch the screen from

all the cameras that are connected to the

system. To turn off, press TALK button twice.

6. INTERPHONE / AUDIO BABY MONITORING

button.

When it is on stand-by mode it activates

interphone communication and audio baby

monitoring.

7. RED/WHITE LED.

Red LED shows active interphone

communication.

White LED shows active visual communication

between doorstation and monitor.

8. MICROPHONE.

9. VOLUME CONTORL.

Allows you to adjust the ring tone volume.

10. Adjust left (only able to use in MENU function)

11. Adjust right (only able to use in MENU function)

12. MENU button

Controls brightness, contrast, colour when

monitor is on, and controls LED backlight when

is on stand-by mode.

13. Master/Slave Settings.

The monitor that is connected to any camera

MUST set its’ two DIP switches to MASTER

position. Rest of the monitor(s) to SLAVE.

14. SPEAKER

15. Connection Terminal (please see fig.1)

Page 4

15

Description of Monitor FUTURO-A4M features (continue)

16. BRACKET

fig.1

Description of Power Supply FUTURO-7PS

Switching power supply

Primary: AC240V 50Hz

Secondary: DC14V 1.5A

Page 5

16

1

2

3

4

5

6

AGVB

D/OD/O

8

9

7

AGV

B

D/OD/O

Description of Door Station FUTURO-CS7 features

1. CCD Camera

2. White LEDs for night vision

3. Speaker

4. Name Plate

5. Call button

6. Microphone

7. Cable terminals to monitor

A(Audio), G(Ground), B(DC14V),

V(Video) to monitor

DO1 & DO2 : Voltage-free Normally

open Door open contact.

WARNING! The following variable

registers should be adjusted by qualified

technicians ONLY

8. Speaker volume on the door station

9. Microphone sensitivity on the door station

Description of Door Station FUTURO-CM7 features

1. Microphone

2. White LEDs for night vision

3. CCD Camera

4. Speaker

5. Name Plate

6. Call Button

7. Speaker volume on the door station

8. Microphone sensitivity on the door station

9. Cable terminals to monitor

A(Audio), G(Ground), B(DC14V),

V(Video) to monitor

DO1 & DO2 : Voltage-free Normally

open Door open contact.

WARNING! The following variable

registers should be adjusted by qualified

technicians ONLY

Page 6

AGV

B

D/OD/O

AGV

B

D/OD/O

One monitor, one audio handsfree station and one doorstation.

IMPORTANT!! Please read page 12 & 13 for cable requirements BEFORE running cables

Page 7

NOTE: When you have changed the

setting of master/slave dip switch

please reset the power.

Two monitors and one doorstation.

IMPORTANT!! Please read page 12 & 13 for cable requirements BEFORE running cables

Page 8

NOTE: When you have changed the

setting of master/slave dip switch

please reset the power.

Two monitors (Futuro-IRON7M and Futuro-A4M combined) two doorstations.

IMPORTANT!! Please read page 12 & 13 for cable requirements BEFORE running cables

Page 9

NOTE: When you have changed the

setting of master/slave dip switch

please reset the power.

Two monitors, two doorstation and two external camera using FUTURO-CPU2

IMPORTANT!! Please read page 12 & 13 for cable requirements BEFORE running cables

Page 10

***For FUTURO-CPU2 description, please

see the manual that comes inside the

FUTURO-CPU2 box***

NOTE: When you have changed the setting of

master/slave dip switch please reset the power.

Basic operation

When a caller presses the call button on the door station, a Ding-Dong sounds on the monitor and the video

screen light up for 45 seconds. If you are satisfied with the identity of the caller press TALK button to speak

(The screen will automatically turn off after 60 seconds).

To turn the screen back on, press MONITOR button once, then you can see the visitor again. To talk to the

visitor, press TALK button. Press TALK button one more time to turn off the monitor.

Monitoring doorstation(s)

Press MONITOR button on the monitor to see an image from a camera.

When system is connected with two doorstations (Camera # 1, Camera # 2) the Camera # 1 will display by

default.

To allow you to switch manually from Camera # 1 and Camera # 2 press MONITOR button.

To turn off, press TALK button twice or wait for 60 seconds.

Monitor adjustment

If desired, the ring volume, colour, contrast and brightness can be adjusted

Adjustments are on the bottom-side of the monitor.

Door Strike operation

When electric door striker and additional power supply for it is in the system, it can be operated from the

monitor(s).

While monitoring or talking, press “DOOR OPEN” button to open the electric door striker.

When more than one door stations are in system, it opens a door striker which is being monitored.

Operation for Intercommunication / Baby Monitoring between Monitors

When system is connected with multiple monitors, internal intercommunication and Audio Baby Monitoring is

available between monitors.

An Intercom calling can be started by any indoor monitor. Press the TALK button on stand-by mode, this

will ring all other monitors in the system but will not activate audio communications until acknowledge from

other monitor(s).

While intercommunication is active you can activate Audio baby monitoring by pressing DOOR RELEASE button

on the monitor to mute the audio and only to listen.

Page 11

• <50 =

12/020 (0.44mm²) shielded cable

(connect shield to G)

AND

RG59/U for video signal

(Connect core to V & shield to G)

• <100M =

24/020 (0.44mm²) shielded cable

(Connect shield to G)

AND

RG59/U for video signal

(Connect core to V and shield to G)

• >100M =

Contact your supplier

Cable requirement - STAR wiring method

Page 12

An additional power supply and

Fig8 cable is required for door

strike operation (Indicated as

broken lines on the diagrams)

Cat5 wire configuration

Cable requirement

Based on the distance from a

camera to the furthest monitor;

• <20M = Cat5 Cable

• <50 =

12/020 (0.44mm²) shielded cable

(connect shield to G)

AND

RG59/U for video signal

(Connect core to V & shield to G)

• <100M =

24/020 (0.44mm²) shielded cable

(Connect shield to G)

AND

RG59/U for video signal

(Connect core to V and shield to G)

• >100M =

Contact your supplier

Cable requirement – Daisy Chain (Loop-in-loop-out) wiring method

Page 13

An additional power supply and

Fig8 cable is required for door

strike operation (Indicated as

broken lines on the diagrams)

Cable requirement

Based on the distance from a

camera to the furthest monitor;

• <20M = Cat5 Cable

Specification

Input Power AC100V~240V (Internal Power Supply)

Power Consumption Idle mode : 2W Operating : MAX 14W

Connecting System 4 wires; 2 Cameras, 1 Monitor and 1 audio handsfree

Voice transmission Half duplex two way communication

Max. Distance & wiring

Monitor to Camera 50M : 0.65mm2 wire 100M : 1.0mm2

wire

Monitor to slave: 20M: 1.5mm2

Door Lock to Camera 20M : 1.0mm2 wire

Display 7 inch Digital Color Display

Resolution 800 (H)X480(V)

Monitor on time Stanby : 40sec Auto off : 80sec

Users Control Brightness, Contrast, Color, Chime volume, Backlight Setting

VIDEOMAN futuro-cm7 User manual

This manual is also suitable for

VIDEOMAN futuro-cm7 User manual

Other documents