Page is loading ...
Specifications
Additional information can be found online at www.heatilator.com
58" [1473]
51-1/8" [1299]
62" [1575]
15-5/8"
[397]
42-1/2"
[1080]
24-1/2"
[622]
8-7/8"
[225]
7-1/4"
[184] GAS ACCESS ELECTRICAL ACCESS
41-3/4"
[1061]
2-3/8"
[60]
8-9/16"
[218]
2-3/4"
[70]
23-3/4"
[603]
36-1/2"
[927]
4"
[102]
8-9/16"
[218]
63" [1600]
8-9/16" [218]
1/2" [25]
17-1/8"
[435]
o
CENTERED ON APPLIANCE
8" [203]
18-1/8"
[460]
Please consult the manufacturer’s
installation manual for all details and
requirements before making a final
design layout decision.
Crave6048ST
48" See-Through Direct Vent
Gas Fireplace
Crave CRAVE6048ST
MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH GLASS SIZE
CRAVE6048ST Actual Framing Actual Framing Actual Framing Actual Framing 47-1/2 x 12-1/2
58 60-1/4 58 60-1/4 41-3/4 42 17-1/8 17
TOP
FRONTLEFT RIGHT
BEFORE FRAMING, PLEASE NOTE:
A minimum of 18" of vertical venting is required before attaching any elbow to the appliance.
Crave CRAVE6048ST
CLEAN FACE TRIM FOUR SQUARE FRONT ILLUSION FRONT
FRONT DIMENSIONS
FINISHED OPENING DIMENSIONS
Decorative Front Dimensions and Framing
25"
[635]
24"
[610]
13-1/8"
[333]
16-3/4
"
[425]
52-5/16" [1329]
51" [1295]
49-3/16" [1249]
5/8" [16]
27-5/16
"
[692]
5-7/8"
[149]
48-3/4" [1238]
57-5/8" [1463]
12-5/8"
[321]
21-3/8
"
[543]
27-5/16
"
[694]
5-7/8"
[149]
49-1/8" [1248]
57-1/2" [1461]
12-1/8"
[308]
21-3/8
"
[543]
19-7/16"
[494]
INSIDE FIT METHOD
(CLEAN FACE TRIM)
FIREPLACE VIEWING AREA
15-3/4"
[400]
51-1/8" [1299]
OVERLAP FIT METHOD
(FOUR SQUARE, ILLUSION)
FIREPLACE VIEWING AREA
17-1/4"
[438]
51-1/8" [1299]
• Rectangular holes on bottom
of access panel should be
covered.
• Approved for 0"-4" finishing
material on inside fit method
• If finishing materials are 0-1”
thick, the outer trim ring
should be adjusted out so
that the trim ring overlaps
the finishing material. This
is intended to provide the
cleanest look.
• If finishing materials are 1-4”
thick, install the trim ring all
the way in. Finishing materi-
als may not extend past the
outside edge of the trim ring.
• Rectangular holes on bottom of
access panel must be exposed.
• ONLY approved for 0"-1"
finishing material on overlap fit
method
• Rectangular holes on bottom of
access panel must be exposed.
• ONLY approved for 0"-1"
finishing material on overlap fit
method
Specifications
PRODUCT LISTING CODES
US ANSI Z21.88-2017
CAN CSA 2.33-2017
UL307B
Additional information can be found online at www.heatilator.com
Product information provided is not
complete and is subject to change
without notice. Product installation
must adhere strictly to instructions
accompanying product to avoid risk
of fire and potential injury.
Lakeville, MN Phone: (800) 927-6841
Web: www.heatilator.com
APPLIANCE LOCATION
WALL PENETRATION
MANTEL LEG/WALL PROJECTIONS
COMBUSTIBLE OR NON-COMBUSTIBLE
48"
[1219]
48"
[1219]
17-1/8"
[435]
60-1/4" [1530]**
1/2"
[13]
1/2"
[13]
Refer to the install manual for hearth, mantel and wall
projection information.
If Passive Heat, HEAT-ZONE® or HEAT-OUT will be installed,
refer to the installation manual for instructions.
FRAMING DIMENSIONS
CLEARANCES TO COMBUSTIBLES
17"
[432]
10"
[254]
42"
[1067]
60-1/4"
[1530]
HEADER
DEPTH** HEADER
DEPTH**
APPLIANCE MAY BE
INSTALLED OFF OF FLOOR***
* Adjust framing dimensions for interior sheathing (sheetrock)
** Header depth not to exceed 3-1/2”
*** If appliance is installed off of floor, maintain required clearances
to combustibles. Construct platform in accordance with local
building codes.
64"
[1626]
10" 12"
63"
[1600]
Do not pack with
insulation or
other material
3 ft. maximum
4-1/2"
minimum
FIREPLACE OPENING
See Appliance dimension diagram
in install manual - Dimension B
Note: Clearance from
opening to
perpendicular wall
Top View
FIREPLACE OPENING
See Appliance dimension diagram
in install manual - Dimension B
Note: Clearance from
opening to
perpendicular wall
Top View
7"
minimum UNLIMITED
Acceptable on both sides of opening
0
0
1"
[25]
31"
[787]
48"
[1219]
55-1/2"
[1410]
MEASUREMENT FROM TOP
OF FIREPLACE OPENING
TO CEILING
MEASUREMENT FROM
BOTTOM OF FIREPLACE
TO CEILING
Crave CRAVE6048ST
Minimal wall penetration
applies to both single-side and
see-through units. Single-side
shown.
GM/HTL/CRAVE6048ST_0420
MANTEL PROJECTIONS - NON-COMBUSTIBLE
MANTEL PROJECTIONS - COMBUSTIBLE
OVERLAP FIT INSIDE FIT
MEASUREMENTS FROM TOP EDGE
OF THE APPLIANCE OPENING
4
5
6
16
3
2
1
6
7
8
9
10
11
18
MAX.
Measurement from top edge of opening
to bottom of appliance = 24-1/2 IN.
MEASUREMENTS FROM TOP EDGE
OF THE APPLIANCE OPENING
4
5
6
16
9
10
18
MAX.
Measurement from top edge of opening
to bottom of appliance = 24-1/2 IN.
7
11
MEASUREMENT FROM
TOP EDGE OPENING
18 20
23
26
29
9
12
6
3
1
Measurement from top edge openin
g
to bottom of appliance = 24-1/2 IN.
MAX.
MEASUREMENTS FROM TOP EDGE
OF THE APPLIANCE OPENING
4
5
6
16
3
2
1
6
7
8
9
10
11
18
MAX.
Measurement from top edge of opening
to bottom of appliance = 24-1/2 IN.
WITHOUT
PASSIVE
HEAT
WITH
PASSIVE
HEAT
NOTE: All measurements in inches.
NOTE: All measurements in inches.
/