Specifications
Additional information can be found online at www.majesticproducts.com
MODEL HEIGHT FRONT WIDTH BACK WIDTH DEPTH VIEWING AREA
Actual Framing Actual Framing Actual Framing Actual Framing
Please consult the manufacturer’s
installation manual for all details and
requirements before making a final
design layout decision.
ECHELON II 48
SEE-THROUGH
Direct Vent Gas Fireplace
58" [1473]
51-1/8" [1299]
62" [1575]
15-5/8"
[397]
42-1/2"
[1080]
24-1/2"
[622]
8-7/8"
[225]
7-1/4"
[184] GAS ACCESS ELECTRICAL ACCESS
41-3/4"
[1061]
2-3/8"
[60]
8-9/16"
[218]
2-3/4"
[70]
23-3/4"
[603]
36-1/2"
[927]
4"
[102]
8-9/16"
[218]
63" [1600]
8-9/16" [218]
1/2" [25]
17-1/8"
[435]
o
CENTERED ON APPLIANCE
8" [203]
18-1/8"
[460]
ECHEL48ST
MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH GLASS SIZE
ECHEL48ST
40,000 BTU (NG)
34,000 BTU (LP)
ACTUAL FRAMING ACTUAL FRAMING ACTUAL FRAMING ACTUAL FRAMING
47-1/2" x 12-1/2"
58" 60-1/4" 58" 60-1/4" 41-3/4" 42" 17-1/8" 17"
The PFF decorative front has an installed depth of 3/4" [19mm], measured from the
front of the non-combustible finishing material to the front of the decorative front.
CFT FRONT PFF FRONT
25"
[635]
24"
[610]
13-1/8"
[333]
16-3/4
"
[425]
52-5/16" [1329]
51" [1295]
49-3/16" [1249]
5/8" [16]
CLEAN FACE TRIM
13-1/8"
[333]
23-3/8"
[594]
4-15/16"
[126]
10-1/16"
[256]
28-5/16"
[719]
The PFF decorative front has an installed depth of 3/4" [19mm], measured from the
front of the non-combustible nishing material to the front of the decorative front.
49-1/4" [1250]
59" [1498]
61-1/4 [1556]
71 [1803]
FRONTLEFT RIGHT
TOP
Specifications
PRODUCT LISTING CODES
US ANSI Z21.88-2017
CAN CSA 2.33-2017
UL307B
Product information provided is not
complete and is subject to change
without notice. Product installation
must adhere strictly to instructions
accompanying product to avoid risk
of fire and potential injury.
ECHEL48ST
MINIMUM FIREPLACE CLEARANCES
FRAMING DIMENSION
CLEARANCES TO COMBUSTIBLES
APPLIANCE LOCATION
1/2" [13]
1/2" [13]
17-1/8" [435]
48" [1219]
60-1/4" [1530]**
48" [1219]
NOTICE:
This see-through appliance is NOT designed
or approved for an indoor/outdoor application.
If Passive Heat, HEAT-ZONE® or HEAT-OUT will be installed,
refer to the installation manual for instructions.
MANTEL LEG/WALL PROJECTIONS
COMBUSTIBLE OR NON-COMBUSTIBLE
WALL PENETRATION
3' maximum
4-1/2"
minimum
FIREPLACE OPENING
See appliance dimension diagram
in install manual - Dimension B
Note: Clearance from
opening to
perpendicular wall
Top View
FIREPLACE OPENING
See appliance dimension diagram
in install manual - Dimension B
Note: Clearance from
opening to
perpendicular wall
Top View
7"
minimum UNLIMITED
Acceptable on both sides of opening
64"
[1626]
10" 12"
63"
[1600]
Do not pack with
insulation or
other material
31"
[787]
0" [0]
0" [0]
1" [25]
48" [1219] 55-1/2"
[1410]
Header depth
not to exceed
3-1/2" [89]
Header
depth
not to
exceed
3-1/2" [89]
Adjust framing dimensions
for interior sheathing (such
as Sheetrock).
If appliance is installed o of oor,
maintain required clearances to
combustibles. Construct platform in
accordance with local building codes.
10" [254]
42"
[1067]
17" [432]
60-1/4"
[1530]
GS/MAJ/ECHEL48ST_0420
Majestic — A Brand of Hearth & Home Technologies
7571 215th Street West | Lakeville, MN 55044
877-486-9123 | majesticproducts.com
MANTEL PROJECTIONS - NON-COMBUSTIBLE
MANTEL PROJECTIONS - COMBUSTIBLE
OVERLAP FIT INSIDE FIT
MEASUREMENTS FROM TOP EDGE
OF THE APPLIANCE OPENING
4
5
6
16
3
2
1
6
7
8
9
10
11
18
MAX.
Measurement from top edge of opening
to bottom of appliance = 24-1/2 IN.
MEASUREMENTS FROM TOP EDGE
OF THE APPLIANCE OPENING
4
5
6
16
9
10
18
MAX.
Measurement from top edge of opening
to bottom of appliance = 24-1/2 IN.
7
11
MEASUREMENT FROM
TOP EDGE OPENING
18 20
23
26
29
9
12
6
3
1
Measurement from top edge openin
g
to bottom of appliance = 24-1/2 IN.
MAX.
MEASUREMENTS FROM TOP EDGE
OF THE APPLIANCE OPENING
4
5
6
16
3
2
1
6
7
8
9
10
11
18
MAX.
Measurement from top edge of opening
to bottom of appliance = 24-1/2 IN.
WITHOUT
PASSIVE
HEAT
WITH
PASSIVE
HEAT
NOTE: All measurements in inches.
NOTE: All measurements in inches.
*Shows center of vent framing hole for top
venting. Center of hope is 1" [25] above
center of horizontal vent pipe.
/
