Teletek electronics MAG4 User manual

Brand: Teletek electronics

Model: MAG4

Category: Fire protection

Type: User manual

English

MAG2

MAG4

FIRE CONTROL PANEL

User Manual

/metal and plastic box/

2 Fire Control Panel MAG2/4 - User Manual

CONTENTS

Guarantee ...................................................................................................................3

1. Using the MAG2/4 controls ...................................................................................4

1.1 Operation modes ...........................................................................................5

1.2 LED indication for zones status ...................................................................5

1.3 LED indication for the technical troubles ....................................................5

1.4 LED indication for the system status ..........................................................6

1.5 Buttons for programming and operation ....................................................6

1.6 Switch for changing over between Access Levels 1 and 3 .......................6

1.7 Sound signalization .......................................................................................7

2. Installing the MAG2/4 re panels .........................................................................7

3. Testing the MAG2/4 re panels ............................................................................8

4. Connecting the zone circuits ...............................................................................8

5. Connecting the sounders circuits .......................................................................9

6. Connecting the FAULT and FIRE relays ..............................................................9

7. Class Change Function .........................................................................................9

8. Operation instructions ........................................................................................10

8.1 Zone Enabling/ Disabling ...........................................................................10

8.2 Sounders Enabling/ Disabling ....................................................................10

8.3 “One man” zone testing ..............................................................................11

9. Technical specications .....................................................................................12

10. Connection diagrams ........................................................................................13

11. Fire alarm record ...............................................................................................14

12. Service record....................................................................................................14

13. Fire alarm event LOG ........................................................................................15

14. Spare parts kits..................................................................................................15

1293

DoP No: 075

1293 - CPR - 0510

Teletek Electronics JSC, 14 Srebarna Str., 1407 Soa, Bulgaria

EN 54-2:1997/A1:2006/AC:1999; EN 54-4:1997/A2:2006/AC:1999

MAG2/4

Intended for use in re detection and re alarm systems in and around buildings.

Essential Characteristics Performance

Performance under re conditions Pass

Response delay (response time to re) Pass

Operational reliability Pass

Durability of operational reliability and response delay: temperature resistance Pass

Durability of operational reliability: humidity resistance Pass

Durability of operational reliability: vibration resistance Pass

Durability of operational reliability: electrical resistance Pass

Fire Control Panel MAG2/4 - User Manual 3

GUARANTEE

The guarantee terms are determined by the serial number (barcode) of the electronic device!

During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is returned

to the factory. All parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or 6 months, whichever

period is longer. The original purchaser shall immediately send manufacturer a written notice of the defective parts or workman-

ship.

International Guarantee

Foreign customers shall possess the same guarantee rights as those any customer in Bulgaria, except that manufacturer shall not

be liable for any related customs duties, taxes or VAT, which may be payable.

Guarantee Procedure

The guarantee will be granted when the appliance in question is returned. The guarantee period and the period for repair are deter-

mined in advance. The manufacturer shall not accept any product, of which no prior notice has been received via the RAN form at:

http://www.teletek-electronics.com/en/support/Service

The setup and programming included in the technical documentation shall not be regarded as defects. Teletek Electronics bears no

responsibility for the loss of programming information in the device being serviced.

Conditions for waiving the guarantee

This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal use.

It shall not cover:

• Devices with destroyed serial number (barcode);

• Damages resulting from improper transportation and handling;

• Damages caused by natural calamities, such as re, oods, storms, earthquakes or lightning;

• Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer;

• Damages caused by unauthorized system incorporation, changes, modications or surrounding objects:

• Damages caused by peripheral appliances (unless such peripheral appliances have been supplied by the manufacturer:

• Defects caused by inappropriate surrounding of installed products;

• Damages caused by failure to use the product for its normal purpose; Damages caused by improper maintenance;

• Damages resulting from any other cause, bad maintenance or product misuse.

In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the manufacturer’s

liability shall be limited to the replacement of the product as sole compensation for breach of the guarantee. Under no circumstances

shall the manufacturer be liable for any special, accidental or consequential damages, on the grounds of breach of guarantee, breach

of agreement, negligence, or any other legal notion.

Waiver

This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or implicit (in-

cluding any implicit guarantees on behalf of the dealer, or adaptability to specic purposes), and over any other responsibilities or

liabilities on behalf of the manufacturer. The manufacturer does neither agree, nor empower, any person, acting on his own behalf, to

modify, service or alter this Guarantee, nor to replace it with another guarantee, or another liability with regard to this product.

Unwarranted Services

The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion under

the conditions below. The manufacturer shall accept no products for which no prior notice has been received via the RAN form at:

http://www.teletek-electronics.com/en/support/Service

The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has prepared a price

list and those products, which can be repaired, shall be paid for by the Customer. The devices with unwarranted services carry 6

month guarantee for the replaced parts.

The closest equivalent product, available at the time, shall replace the products, the manufacturer deems un-repairable. The cur-

rent market price shall be charged for every replaced product.

This manual contains information on limitations regarding product use and function and

information on the limitations as to liability of the manufacturer.

The entire manual should be carefully read!

WARNING

The system is to be installed by a qualied person to the latest Fire Alarm and Installation Regulations which

are mandatory in the applicable country of installation.

Before commencing the installation of this Fire Alarm Panel, ensure it is sited in a position, which is visible

to the Fire Brigade when entering the premises, and where ease of access is provided for users and service

engineers. Space must be available to easily open external and internal doors.

The Electrical Supply to the panel must be isolated and must not be capable of being accidentally switched

off. A ‘Lockable Switch fuse Unit’ positioned within 2 meters of the panel should be clearly labelled FIRE

ALARM - DO NOT SWITCH OFF.

EN 54-2 compatible panels.

All specications are subject to change without notice.

Technical Support help:

+359 (2) 9694 800

4 Fire Control Panel MAG2/4 - User Manual

1. Using the MAG2/4 control

Description of the front panels elements:



LED indication for the zones status:

MAG2 - 2 zones

MAG4 - 4 zones

Buttons for programming and operation, see item 1.5.

LED indication for the system status, see item 1.4.



LED indication for the technical troubles - see item 1.3.

Note: This indication is not visible for the user. To examine the technical

troubles in the system, the engineer has to remove the front cover of the

box.

Switch for changing over between Access Levels 1 and 2 - see item 1.6.

Front view MAG2 Front view MAG4

 

 

 

 

 

Fire Control Panel MAG2/4 - User Manual 5

1.1 Operation modes:

MODE Indication

Normal • The green LED next to the ‘power Supply 230V AC’ will be illuminated.

Fire

• The integrated red status FIRE LED and a zone identication LED will

ash together on receipt of a FIRE condition and become steady after the

SILENCE ALARM button is pressed.

• An internal buzzer will operate until silenced with SILENCE BUZZER

button.

• The external sounders will operate.

• The FIRE relay on the main board will energize.

Fault

• The yellow GENERAL FAULT LED will always illuminate together with

an external or internal identication LED.

• An internal buzzer will sound.

• The FAULT relay on the main will de-energize.

1.2 LED indication for the zones status:

ZONE LED Indication

Red • Fire alarm in the zone.

Yellow • Zone fault - open or short circuit. Detector head removed.

• Zone test - the LED is blinking during the test procedure.

1.3 LED indication for the technical faults:

FAULT Fault description

○ µP Processor break down.

○ Sounder 1 Sounder Circuit One fault - open or short circuit, reverse

connected sounder, or bad sounder parameters.

○ Sounder 2 Sounder Circuit Two fault - open or short circuit, reverse

connected sounder, or bad sounder parameters.

○ +24V DC Overload Overload of “+24” VDC power supply.

○ +24V DC Failed Absence of “+24” VDC power supply.

○ Battery Low Low battery condition.

○ Battery Lost Battery loss.

○ AC Mains Supply loss.

○ Charger Battery charger fault.

○ AUX Auxiliary supply fault.

○ Earth Short circuit to earth.

Battery Low, Battery Lost and Charger LEDs are lighting up together in case of

overload of the battery charger output.

6 Fire Control Panel MAG2/4 - User Manual

1.4 LED indication for the system status:

LED Indication

FIRE

(red) Fire in the premises.

GENERAL FAULT*

(yellow) Main Fault indicator.

SOUNDER FAULT/DISABLE*

(yellow)

Trouble in the sounder circuit - open or short circuit;

reverse connected sounder.

ENABLE / DISABLE

(yellow)

Lights permanently at disabled zones/sounders.

Blinks during enabling/disabling of zones or

sounders.

TEST

(yellow)

Blinks during “One Man” Test together with the LED

of the tested zone.

POWER SUPPLY 230V

(green)

Lights on permanently in normal operating mode,

indicates presence of main power supply 230V.

1.5 Buttons for programming and operation:

Button Description

SILENCE BUZZER Deactivating the internal buzzer.

SILENCE ALARM Deactivating sounders.

ENABLE / DISABLE Enabling / Disabling of Zones / Sounders.

TEST / SCROLL Test mode; Scroll forward zones.

RESET Initialization; Conrm the introduced changes.

SOUND ALARM Activating sounders.

1.6 Switch for changing over between Access Levels 1 and 2:

Position Description

OFF Access Level 1 - only the “SILENCE BUZZER” button is active.

ON Access Level 2 - all buttons at the front panel are active.

* NOTE: Fault conditions will not be announced instantly. There will be a short delay

which will vary from condition to condition. Faults when cleared will automatically reset

at the panel.

Fire Control Panel MAG2/4 - User Manual 7

1.7 Sound signalization

Signal Description

Short beeps After pressing the “RESET” button and upon the initial start-up of the

panel.

Continuous

beep

Fire and/ or Fault operating mode. The signal can be stopped by

pressing the “SILENCE BUZZER” button, but the LED indication

remains.

Interrupted

beep

After pressing the “ENABLE/DISABLE” button to enable/disable zones/

sounders and the “TEST/SCROLL” button to access “One Man” test

mode of zones. The signal can be stopped by pressing the “SILENCE

BUZZER” button, but the LED indication remains.

2. Installing the MAG2/4 re panels

• Choose the best location for the panel position, with an ambient temperature between

-5°C and 40°C, away from heating sources, environmental dust and potential water

ingress.

• Remove all packaging and inspect visually the panel for any damage.

• Remove the outer cover. Stow the cover in a safe position.

• Inspect the internal PCB and make sure the internal components are rmly in place.

• Remove the PCB from the metal / plastic box. Stow in a safe location.

• Choose which cable entry points to knock out and carefully remove the knock-outs.

• Drill the wall to suit the back box centre xing position, plug and insert a xing screw.

Note: If you are installing MAG 2/4 in plastic box use the template on the back side of

the packaging box to drill the mounting holes on the wall.

• Fix the metal / plastic housing into mounting position and insert xing screws.

• Tighten all the xing screws.

• Route the external cables onto the back box, make off connection glands etc., DO NOT

make any connections at this stage. ENTER THE MAINS CABLE THROUGH ITS

OWN CABLE ENTRY POINT AND KEEP MAINS WIRING AWAY FROM SYSTEM AND

OTHER LOW VOLTAGE WIRING.

• Fit the EOL modules from the supplied additional parts one-by-one to every zone

terminal. ATTENTION: Observe the polarity - the red wire to “+” point and the black

wire to “-” point.

• Fit the EOL resistors from the supplied additional parts one-by-one to the sounders

terminal.

• Re-t the PCB to the metal / plastic box.

• Place the temperature sensor behind or under the accumulator battery.

• Connect the mains supply and earth to the main terminal block. DO NOT switch on the

main electrical supply at this stage.

• Position the battery in an upright position and place the temperature sensor behind it.

• Close the outer cover using the nuts and screws from the spare parts kit:

8 Fire Control Panel MAG2/4 - User Manual

3. Testing the MAG2/4 re panels

ATTENTION: It has been assumed that prior to making the connection

at the panel, the integrity of the system ALL wiring has been

comprehensively tested, including insulation to earth.

• Switch on the mains power supply.

• Connect the battery leads from the black power supply box to the positive and

negative battery terminals.

• If the buzzer and indicator LED’s are operating, press the RESET button.

In Normal Operating Mode only POWER SUPPLY 230V will be illuminated.

NOTE: The battery might show a ‘Low Battery Fault’ initially until it has had time to

charge up to the required level.



If other LEDs are illuminated and the buzzer is sounding, carefully check all

fuses and connections. Refer to the page 7 for the associated yellow LED’s

apply to. The connection diagram on the inside of the external cover will assist

in identifying the LED.

ATTENTION: Do not short out the battery terminals because an internal

protection will switch on and the panel will stop function!

If by some chance the fault will not cancel, and only on the advice of our Technical

Support Department, return the PCB CHASSIS ONLY to your supplier. DO NOT

return the metal / plastic box.

4. Connecting the zones circuits

• Disconnect the mains power supply and the battery connection.

• Remove the EOL-module from the zone 1 terminal on the main module and t it to the

last detector of the zone 1 circuit as observe the polarity:

• Ensure all terminations are made correctly and all detector heads are plugged into their

bases.

• Connect Detector circuit ONE to the panel terminal block.

• Power up the panel with the mains and battery.

• Press RESET button.

The panel should be in the ‘NORMAL MODE’.



If General Fault and zone 1 FAULT LED’s illuminate, there is a wiring/

connection problem. Check the polarity of the connection, the connection of

the devices and whether a head is removed. Check the EOL proper polarity

and position.

Fire Control Panel MAG2/4 - User Manual 9

• Operate ALL detection devices applicable to this zone, to ensure correct receipt of a re

signal and the correct operation of the panel controls. Refer to the User Instructions on

the inside of the panel.

• Repeat the connection process for the other zones stated above. ENSURE the supply

voltages are initially disconnected prior to each stage.

Once the connection of the zones is completed, connect and test any

of the other auxiliary circuits BEFORE connecting the external sounder

circuits.

5. Connecting the sounders circuits

• Disconnect the mains power supply and the battery connection.

• Remove the EOL-Resistor from the terminal block of sounder circuit 1 (SND 1) and t

to the last sounder of circuit one:

brown

black red

10K

LEGEND

Sounders

S1 S2 SN

• Check all sounder connections are made.

• Connect sounder circuit ONE to the panel terminal block.

• Apply mains and battery power.

• Press RESET.

The panel should be in the ‘NORMAL MODE’.

• Activate a zone Call Point. The sounders should operate. Press the RESET button.

Repeat the connection process for the second external sounder circuit, as stated above.

ENSURE the supply voltages are initially disconnected prior to each stage.



If General Fault and SOUNDER FAULT / DISABLE LED’s illuminate, there is

a wiring / connection problem. Check the polarity of the connection of each of

the devices, the polarity of the connection of the devices to the Panel terminal

block or whether an earth fault exists.

6. Connecting the FAULT and FIRE relay circuits

FAULT and FIRE Relays - The on board relays volt free change over terminals are

for low voltage use only. Attention: Mains supply MUST NOT BE APPLIED to these

terminals.

7. Class Change Function

To use the class change function connect the terminals of a switch with normally open

contacts to the CC (Class Change) clamps of the main module terminal. The working

mode of the sounders will be:

- when the switch is pressed - one second sounder on, one second sounder off;

- when the switch is depressed - the sounder is off.

10 Fire Control Panel MAG2/4 - User Manual

8. Operation instructions

8.1 Zone Enabling/ Disabling

Z To disable a zone:

• Press ENABLE/ DISABLE:

DISABLE/ ENABLE LED blinks.

The ZONE 1 yellow LED blinks if ZONE 1 is en-

abled and lights permanently if ZONE 1 is disabled.

• Press TEST/ SCROLL, until

you reach the zone which has to

be disabled:

The respective zone yellow LED blinks.

• Press ENABLE/ DISABLE: The yellow LED of the disabled zone lights up per-

manently.

• Press RESET: At this step the zone is disabled.

Z To enable a zone:

• Press ENABLE/ DISABLE:

DISABLE/ ENABLE LED blinks.

The ZONE 1 yellow LED blinks if ZONE 1 is en-

abled and lights permanently if ZONE 1 is disabled.

• Press TEST/SCROLL, until you

reach the zone which has to en-

able:

The yellow LED of the disabled zone lights up per-

manently.

• Press ENABLE/ DISABLE: The yellow LED of the enabled zone blinks.

• Press RESET: At this step the zone is enabled.

8.2 Sounders Enabling/ Disabling

A sound signalization is activated at every Service Mode entering. The

signalization is off by pressing “SILENCE BUZZER” button.

Z To disable the sounders:

• Press ENABLE/ DISABLE:

DISABLE/ ENABLE LED blinks.

The ZONE 1 yellow LED blinks if ZONE 1 is en-

abled and lights permanently if ZONE 1 is disabled.

• Press TEST/ SCROLL, until

you reach the last zone in the

system:

The SOUNDER FAULT/DISABLE LED will start

blinking.

• Press ENABLE/ DISABLE: The SOUNDER FAULT/DISABLE LED lights up

permanently.

Fire Control Panel MAG2/4 - User Manual 11

• Press RESET:

The SOUNDER FAULT/DISABLE and ENABLE/

DISABLE LEDs light up permanently.

At this step the sounders are disabled.

You can exit the sounder disabling mode also by pressing the “TEST/ SCROLL” button,

as in that case the you reject the procedure.

Z To enable the sounders:

• Press ENABLE/ DISABLE:

DISABLE/ ENABLE LED blinks.

The ZONE 1 yellow LED blinks if ZONE 1 is en-

abled and lights permanently if ZONE 1 is disabled.

• Press TEST/ SCROLL, until

you reach the last zone in the

system:

The SOUNDER FAULT/DISABLE LED lights up

permanently.

• Press ENABLE/ DISABLE: The SOUNDER FAULT/DISABLE LED will start

blinking.

• Press RESET: At this step the sounders are enabled.

You can exit the sounder enabling mode also by pressing the “TEST/ SCROLL” button,

as in that case the you reject the procedure.

8.2 “One man” Zone Testing

The “One Man” Test mode gives the installer the possibility to test the efciency of the

system - whether the detectors react to smoke, heat, etc.

Z To do “One Man” Test of a zone:

• Press TEST/ SCROLL: µP Fault and General Fault LEDs light off. All other

system indication LEDs light on permanently.

• Press TEST/ SCROLL again:

The TEST LED and ZONE 1 yellow LED start

blinking.

ZONE 1 is in test mode. Test a detector from this

zone whether it react to smoke, heat, etc.

• Press TEST/ SCROLL again to

continue with the system testing:

TEST LED will continue blinking.

The ZONE 1 yellow LED lights out (the zone is

not longer in test mode). The ZONE 2 yellow LED

blinks in yellow.

ZONE 2 is in test mode. Test a detector from this

zone whether it react to smoke, heat, etc.

Continue the system testing by pressing the “TEST/ SCROLL” button. The exit from the

“One Man” Test mode is automatic after the end of the test procedure in the last Zone 4,

or at any time by pressing “RESET” button.

12 Fire Control Panel MAG2/4 - User Manual

9. Technical Specications of MAG2 and MAG4

Zones:

• MAG 2 - 2 xed zones

• MAG 4 - 4 xed zones

Maximum number of detectors per zone:

• Up to 20 (or 32 SensoMAG series) conventional detectors and unlimited number of

manual call points.

Thresholds for zone conditions:

• 0 ÷ 2 mA - Open circuit fault condition

• 2 ÷ 10 mA - Normal condition

• 10 ÷ 110 mA - Fire Alarm condition

• 110 mA - Short circuit condition

Power Supply:

• Main Power supply: 230V AC ±10%; 0.315A fuse

• Standby Power supply: 1 x 12V / 7Ah; 2A fuse

• Internal resistance of accumulator battery: Ri < 1.6Ω

Maximum current available for system devices (with fully charged battery):

• 0.7 A

Current consumption - mains failure:

• 50 mA

Outputs:

• Sounder Circuit 1: 24V / 0.3A; 0.3A fuse (PTC)

• Sounder Circuit 2: 24V / 0.3A; 0.3A fuse (PTC)

• Fault Relay, volt free changeover contacts*: 3A @ 120V AC; 3A @ 60V DC

• Fire Relay, volt free changeover contacts*: 3A @ 120V AC; 3A @ 60V DC

* Note: These functions may not be used to provide any “Options with requirements” as specied

in EN 54-2.

Auxiliary output:

• 24V DC, 0.3A fuse (PTC)

Cabling:

• Maximum 2.5mm diameter

Environment:

• Working temperature: -5 to 40°C

• Storage temperature: -20 to 60°C

• Humidity: 0 to 95%

Temperature sensor:

The temperature sensor is used for measurement of the battery temperature. The sensor

is mounted at the end of the wired y lead, factory connected to “Temperature sensor”

terminal on the panel’s PCB.

The temperature sensor should be placed behind or under the battery.

Fire Control Panel MAG2/4 - User Manual 13

10. Connection Diagrams

Connection circuit MAG2/4 metal box

Connection circuit MAG2/4 plastic box

14 Fire Control Panel MAG2/4 - User Manual

11. Fire Alarm Record

Installation Address: .......................................................................................................

.......................................................................................................

Contact Person: .......................................................................................................

Telephone: .......................................................................................................

Fax: .......................................................................................................

Date Completed: .......................................................................................................

Commissioned By: .......................................................................................................

Contract Reference: .......................................................................................................

Service Intervals: Monthly / Quarterly / Half Yearly / Annually

ZONE

No LOCATION

DETECTOR TYPE and

QUANTITY PER ZONE

SOUNDERS

(Zone Quantity and

Related Circuit )

Ion* Ph RoR F/T CP Circuit1 Circuit2

TOTALS:

* Ion - Ionisation sensor, Ph - Photoelectric sensor, RoR - Rate of Rise sensor, F/T - Fixed

Temperature sensor, CP - Call Point

System Installed By: .........................................................................................................

Telephone / Fax: ................................................................................................................

12. Service Record

Date Visit

Completed

Zones

Tested

Faults

Rectied

Signature of

Engineer

Next Due

1 2 3 4 Name:

Fire Control Panel MAG2/4 - User Manual 15

13. Fire Alarm Event LOG

DATE TIME FIRE

yes / no

ZONE

number

FAULT

yes/no and

TYPE

ACTION

TAKEN Name

14. Spare Part Kits

www.teletek-electronics.com

Address: 14A Srebarna Str., 1407 Soa, Bulgaria

tel.: (+359 2) 9694 800, fax: (+359 2) 962 52 13

e-mail: [email protected]

18020244, Rev.B, 02/2016

Teletek electronics MAG4 User manual

Brand: Teletek electronics

Model: MAG4

Category: Fire protection

Type: User manual

Download PDF

report

Teletek electronics MAG4 User manual

Teletek electronics MAG4 User manual

Related papers

Other documents