Innovative WNST-4-CW-124 Installation guide

NOTE:

Depending on your

Winston Workstation®

conguration, you

may not receive all the

parts shown within this

instruction booklet.

Installation may require

two people.

CAUTION:

Mechanism can rise quickly

with no equipment in place.

User equipment must be

properly installed, prior to

height adjustment. Failure

to do so may result in

personal injury and/or

property damage.

WNST-1 WNST-2

WINSTON WORKSTATION

Installation Instructions

Human Active Technology

800 524 2744

customerservice@team-hat.com

team-hat.com

®

PAGE 1 OF 11

A Worksurface

111435

B Column

411470

C Felt Pad

111464

D Freestanding Base

111248

E Cable Retainer

111735

F 3/8-16 x 1" FHSCS

701124

G Screws

713273

H Top Plate

111736

I Utility Tray

113025

J 10-32 x 1" FHSCS

711467

K Beam (10" or 30")

412036 or 412037

L Column Clamp

111040

M 1/8" Allen Wrench

701312

N 7/32" Allen Wrench

701127

O Column Cap

111275-708

P Quick Connect VESA Plate

114808

Q M4 x 12mm Phillips Pan Head Screw

701153

R Monitor Tilter

8500 Tilter

S Dog Washer

111230-603

T 10-32 x 1/2" FHSCS

711240

U Column Cable Clip

111203-708

Depending on your Winston Workstation® configuration,

you may not receive all parts shown below.

PARTS LIST

PAGE 2 OF 11

i

A

B

Use 7/32" Allen wrench to

press cable rmly into place.

Conrm cable is

properly seated

into position.

N

IMP OR TAN T: Do not pull excessively

on cable – doing so may result in

accidental actuation of column.

CAUTION: Do not press height adjust

button until unit is fully assembled.

1a 1b 1c

1

PAGE 3 OF 11

D

C

Hang base plate over edge

of worksurface to allow

access to countersunk

holes. Side of base plate

with felt pads should be

face down.

Place worksurface

on base plate to aid

as a counterbalance.

F

E

2 3 4

5 6

7/32"

PAGE 4 OF 11

I

Slide utility tray onto

worksurface. Utility

tray simply rests on

top of worksurface.

H

G

7 8

PAGE 5 OF 11

L

J

K

O

M

910

11 12

iIMPORTANT:

Tighten bolts evenly.

The beam should sit

ush against the col-

umn, ensure there

are no gaps. Also,

it is important the

worksurface clamp

is level.

1

3

2

4

1/8"

PAGE 6 OF 11

13

Q

P

PAGE 7 OF 11

R

14

PAGE 8 OF 11

15

i

1/8"

M

S

T

1/8"

iTILTER FRICTION ADJUSTMENT

M

1/8"

PAGE 9 OF 11

U

16

PAGE 10 OF 11

iIS YOUR HEIGHT ADJUST BUTTON NOT WORKING?

If so, make the adjustments below.

Slide workstation so that

the worksurface hangs over

desk edge to allow access to

underneath the worksurface.

Loosen the two screws

as shown.

Slide bracket in the direction

shown and tighten screws.

Test height adjust button –

readjust by repeating the steps

above as necessary.

Press button and hold. Lift up/down. Release to lock in place.

17a

17b

17c

17d

17

PAGE 11 OF 11

Innovative WNST-4-CW-124 Installation guide

Innovative WNST-4-CW-124 Installation guide

Related papers

Other documents