Seco SANTARO 19.0 SG Owner's manual

Category
POS terminals
Type
Owner's manual
Product Manual
SANTARO 19.0 SG
Arm® Cortex®-A9 Flush Mount
2
PRODUCT MANUAL
SANTARO
Document Revision History
The information in this document is subject to change without prior notice in order to improve reliability, design and
function and does not represent a commitment on the part of the manufacturer.
Online support on edge.seco.com
Revision Date Author Description
V 1 07.03.2017 CG Initial document release for PCB revision V 1.2
V 2 15.03.2018 CG Page 18 New Picture RS485 Pin 6 to 11
V 3 25.06.2019 CG Page 9 „Synchronous Serial Interface" n/a X1
V 4 26.08.2019 CG Changr address
V 5 17.12.2021 bmy SECO CI Update 2022
PRODUCT MANUAL
SANTARO
Table of Contents
1. Introduction .........................................................................................4
2. Safety Hints .........................................................................................5
3. Product Introduction .......................................................................... 6
3.1 Type Plate and Device Information ..............................................................6
3.2 Product names and variants .........................................................................7
3.3 Related Documents and Online Support ....................................................8
4. Technical Data .....................................................................................10
4.1 Block Diagram SBC .......................................................................................12
4.2 Conectors ........................................................................................................13
5. Installation and Start Up .....................................................................15
5.1 Connection Scheme ......................................................................................15
6. Internal and External Interfaces .........................................................16
6.1 Ethernet (X24).................................................................................................16
6.2 Power (X1) .......................................................................................................17
6.3 Digital I/O (X14) ..............................................................................................18
6.4 CAN/RS-485 Interface (X39) ........................................................................19
6.5 Speaker (X9) ...................................................................................................20
6.6 Keypad/SPI (X21) ...........................................................................................21
6.7 RS-232/RS-232 (X13) ....................................................................................23
6.8 USB Host (X34) ..............................................................................................24
6.9 USB OTG (X20) ..............................................................................................24
6.10 SD Card Reader (X31) ..................................................................................24
6.11 Reset Switch (SW1) .......................................................................................25
6.12 Bootselect Switch (SW2) ..............................................................................25
6.13 Power LED (D30) ............................................................................................ 25
6.14 HDMI (X111) ...................................................................................................26
6.15 Battery-Holder (X2) * .....................................................................................27
7. Battery .................................................................................................28
7.1 BatterySpecicationsX1/X2 ...................................................................... 28
7.2 BatterySpecicationsX4 .............................................................................. 28
7.3 Replacement of the Internal Battery ...........................................................29
Annex A: Technical Drawing ...............................................................................30
Annex B: Quality and Incoming Inspections .....................................................31
B-1 Display and Touch ..........................................................................................31
Annex C: Hardware Revision Information .........................................................32
Annex D: Assembly Options ............................................................................... 33
D-1 Wi-Fi / Bluetooth .............................................................................................33
Annex E: Guidelines and Standards .................................................................34
E-1 RoHS Declaration ...........................................................................................34
E-2 Supplier Declaration – Directive EG 1907/2006 REACH ..........................34
E-3 ULCertication ............................................................................................... 34
E-4 SECO Northern Europe Conformity Statement ......................................... 35
Annex F: Common Documentation ....................................................................36
F-1 Warranty Hints ................................................................................................36
F-2 Field of Application.........................................................................................37
Annex G: Technical Support ..............................................................................38
Annex H: General Information ............................................................................ 39
* alternative assembly upon request
4
PRODUCT MANUAL
SANTARO
1. Introduction
Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional
use and therefore we suppose extended technical knowledge and practice in working with such products.
The information in this manual is subject to technical changes, particularly as a result of continuous
product upgrades. Thus this manual only reflects the technical status of the products at the time
of printing. Before design-in the device into your or your customer’s product, please verify that this
document and the therein described specication is the latest revision and matches to the PCB
version. We highly recommend contacting our technical sales team prior to any activity of that kind.
The attached documentation does not entail any guarantee on the part of SECO Northern Europe
GmbH with respect to technical processes described in the manual or any product characteristics
set out in the manual. We do not accept any liability for any printing errors or other inaccuracies in
the manual unless it can be proven that we are aware of such errors or inaccuracies or that we are
unaware of these as a result of gross negligence and
SECO Northern Europe has failed to eliminate these errors or inaccuracies for this reason.
SECO Northern Europe GmbH expressly informs that this manual only contains a general
description of technical processes and instructions which may not be applicable in every individual
case. In cases of doubt, please contact our technical sales team.
In no event, SECO Northern Europe is liable for any direct, indirect, special, incidental or
consequential damages arising out of use or resulting from non-compliancy of therein conditions
and precautions, even if advised of the possibility of such damages.
Before using a device covered by this document, please carefully read
Annex „F-1 Warranty Hints“
Annex „F-2 Field of Application
Embedded systems are complex and sensitive electronic products. Please act carefully and ensure
that only qualied personnel will handle and use the device at the stage of development. In the
event of damage to the device caused by failure to observe the hints in this manual and on the
device (especially the safety instructions), SECO Northern Europe shall not be required to honour
the warranty even during the warranty period and shall be exempted from the statutory accident
liability obligation. Attempting to repair or modify the product also voids all warranty claims.
5
PRODUCT MANUAL
SANTARO
2. Safety Hints
Please read this section carefully and observe the instructions for your own safety and correct use of the device.
Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded
systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this
condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.
I. General Handling
Don’t drop or strike the unit: The PCB, display and/or other parts might be damaged.
Keep away from water and other liquids, the unit is not protected against.
Operate the unit under electrical and environmental conditions according to the technical
specication.
The electrical installations in the room must correspond to the requirements of the local (country-
specic) regulations.
Take care that there are no cables, particularly power cables, in areas where persons can trip over
them.
Do not place the device in direct sunlight, near heat sources or in a damp place.
All plugs on the connection cables must be screwed or locked to the housing.
Repairs may only be carried out by qualied specialist personnel authorized by
SECO Northern Europe GmbH or their local distributors.
Maintenance or repair on the open device may only be carried out by qualied personnel
authorized by SECO Northern Europe GmbH which is aware of with the associated dangers.
II. Electricity
The embedded systems may only be opened in accordance with the description in this user’s
manual for
- replacing of the (rechargeable, where applicable) lithium battery and/or
- conguration of interfaces, where applicable
These procedures have to be carried-out only by qualied specialist personnel.
When accessing internal components the device must be switched off and disconnected from the
power source.
When purchased core or basic versions without protecting back cover, don’t touch the PCB directly
with your ngers. Especially these products need to be handled very carefully.
Don’t operate or handle the unit without typical ESD protection measures, such as ground
earthing.
Operate the unit according to the technical specication only.
III. Damage or Permanent Malfunction
It must be assumed that a safe operation is no longer possible, in case
-the device has visible damage or
-the display is dark or shows strange pattern for longer period
-the device doesn’t react after a reset
In these cases the device must be shut down and secured against further use
IV. LCD and touch handling
If equipped with, the soft surface of a resistive touch screen is not suitable for use with stencils
and/or other devices for touch operation. There are special plastics pens available in commercial
shops. A projective capacitive touch screen might be protected by a heat strengthened glass or
acrylic or polycarbonate cover lens. These are dedicated for use with nger tips. There are very
special pens available which might work with a PCT touch.
Protect the LCD/touch/cover lens against scratches and sharp edges. The warranty does not cover
pixel failures resulting from non-compliant handling.
Clean the LCD/touch/cover lens with a soft cotton cloth with alcohol. Don’t use organic solvents,
acid or alkali solutions.
Water drops, nger fat or any similar fouling should be removed immediately from the LCD, cover
lens and metal frame to avoid any staining.
6
(Exemplary Illustration. It shows the SANTARO 10.1" BX PCT.)
S/N: YY-WW
Made in Germany
25,4
50,5
Art.No.: 900-0000R
Model: SANTARO x1
9-32 V ; 2,3-0,65 A
Position of Typelabel
S/N: YY-WW
Made in Germany
25,4
50,5
Art.No.: 900-0000R
Model: SANTARO x1
9-32 V ; 2,3-0,65 A
SECO Northern Europe article number
Product name and conguration
Serial number
Power ratings
Production date (week/year)
PRODUCT MANUAL
SANTARO
3. Product Introduction
This document is applicable for hardware revisions 1.0 or later of the SANTARO series.
Please nd the hardware version grid in „Annex C: Hardware Revision Information:
SANTARO is an Embedded System to be used as human machine interface (HMI) in various applications. Please
refer to Annex „F-2 Field of Application for further information. The system is equipped with a large number of
industrial interfaces. A wide variety of options is available as well.
3.1 Type Plate and Device Information
For service and later identication of the device, the type plate contains important information.
7
PRODUCT MANUAL
SANTARO
3.2 Product names and variants
Product name denition:
SANTARO <CPU> <7.0> <OF> <PCT> <IPS> <additional description> <Vx.y.z>
Explanation:
SANTARO product family name (invariable)
<CPU> x1, x2, x4 number of cores inside the i.MX6 processor
<7.0> display size in inch
<OF> <SG> <BX> mechanical design of enclosure
<PCT> projected capacitive touch; if blank: 4-wire resistive
<IPS> display technology “in-plane switching”, (option)
<additional description> contains variants which are important to sales product description, i.e.
without or with WLAN/Bluetooth module (“W/B”)
untreated glass surface or including antiglare treatment (“AG”)
front frame made from die-cast zinc or aluminium (“Alu”)
different memory capacities for RAM and/or eMMC
customer-specic reduced assembly
etc.
<Vx.y.z> revision of PCB layout
<x> describes major changes in form t and functions
<y> describes variants that are different in PCB layout and could affect the list of
critical components (UL LoCC).
<z> describes minor changes to PCB layout due to production optimization like
solder resist mask or drilling diameters.
Also minor changes in assembly of PCB and/or device which do NOT affect the
list of critical components (UL LoCC) due to unlisted components or declared
“interchangeable”.
Windows CE 7
https://bit.ly/3xQ6GGy
Contains information about Windows Embedded CE 7, the tool chain, the
development environment Visual Studio, SECO Northern Europe tools, etc.
Windows CE 2013
https://bit.ly/3G8HBJQ
Contains information about Windows Embedded CE 2013, the tool chain,
the development environment Visual Studio, SECO Northern Europe tools,
etc.
Linux Yocto Rocko
https://bit.ly/3lvVFFu
Linux Yocto Daisy
https://bit.ly/3DeOsjb
Contains information about Linux BSP with development environment
Linux Embedded System Yocto (Codename: Daisy, Version 1.6.1)
includes rst information about the bootloader Flash N Go
Linux Yocto Jethro
https://bit.ly/3ryeETG
Contains information about Linux BSP with
development environment Linux Embedded System Yocto (Codename:
Jethro) includes rst information about the bootloader Flash-N-Go
Android 4.2.2
https://bit.ly/3xSlHry
Contains information about Android 4.2.2 including the SDK
Android 7.1
https://bit.ly/3pnptFt
8
PRODUCT MANUAL
SANTARO
3.3 Related Documents and Online Support
This document contains operating system specic information. The following additional documentations are
available:
OPERATING SYSTEMS
Flash-N-Go
https://bit.ly/31h2ioh
Contains information about the usage of the G&F Flash-N-Go solution
which consists of three submodules:
Flash-N-Go Boot (A tiny boot loader)
Flash-N-Go System (A maintenance os)
Flash-N-Go Update (A GUI based update solution for all os)
9
PRODUCT MANUAL
SANTARO
UPDATE / BOOT / SYSTEM
CPU x1 x2 x4
CPU Type i.MX6Solo i.MX6Dual i.MX6Quad
Core Class Arm® Cortex®-A9
Core Clock 800 MHz 1 GHz
Features
NEON for SIMD media acceleration and VFP operations; Multi-format HD 1080p video decoder and HD
720p video encoder hardware engine; L1 cache, 32 KB for instruction, 32 KB for data
512 KB L2 cache 1 MB L2 cache
HW Accelerators Open VG 1.1 (Emulated on 3D
GPU) OpenVG 1.1
RTC Accuracy: +/- 30 ppm at 25°C
Memory
eMMC Flash 4 GB MLC eMMC
RAM Standard 1 GB 32 bit DDR3L 1 GB 64 bit DDR3L
SRAM 512 KB
SD Card Slot 4 bit MMC/SDIO/SD/SDHC
Operating Systems
Supported OS Windows CE 7/2013, Linux Yocto, Android
Communication Interfaces
Digital I/O 2x In, 2x Out (0.7 A)
Network 1x 10/100 Mbit/s Ethernet (RJ-45)
USB 2.0 1x 480 Mbit/s Host (Type A)
1x 480 Mbit/s OTG (Type Micro-AB) 1
CAN Fieldbus/ RS-485 1x CAN (ISO/DIS 11898) + 1x
RS-485 1x CAN (ISO/DIS 11898) + 1x RS-485 galvanic isolated
RS-232 2x RS-232 (RX/TX/CTS/RTS)
MDB 2 /1x MDB (Master / Slave optional) 3 instead of 2nd external RS-232
Synchronous
Serial Interfaces n/a SPI up to 12 chip selects; I²C; Matrix keypad up to 8 x 8
Video
Video output Full HD micro HDMI
Audio
Speaker output 1x speaker (connector), 1.5 W RMS (8Ω)
10
PRODUCT MANUAL
SANTARO
4. Technical Data
1
Mechanically the Micro-USB interface has not been designed for frequent contact operations. Please use an
adapter cable with a strain relief.
2
Option
3
The selection of a variant eliminates the other.
Audio Internal 1x speaker 0.3 W RMS (8Ω) parallel to external output
Display and Touch
Size 19.0 inch/481.93 mm
Resolution 1280 x 1024 pixel
Brightness Typ. 280 cd/m²
Backlight Lifetime Typ. 50
000 h
Viewing Angle 80°,80°,85°,85° (UDRL)
Color 24 bit (16.7 Mio. colors)
Touch projected capacitive multi touch
Housing x1 x2 x4
11
PRODUCT MANUAL
SANTARO
Front tbd.
Frame None
Rear ABS-PC/1.4016 stainless steel
Ingress Protection Front IP 20/Rear IP20
Device Dimensions
W x H x D 457.3 x 382.1 x 42.2 mm
Weight 4820 g
Power Supply
Supply Voltage Nom. 13 to 32 V DC
Consumption Typ. 28.3 W; max. 42.1 W
Internal Backup Battery (RTC) Type: 3 V Lithium cell Type CR1220:
Lifetime (RTC only): Approximately 8 years, depending on application
Type: 3 V Lithium cell Type CR
2032: Lifetime(RTC+SRAM):
10 years
Typical Environmental Conditions
Storage Temp. -20 to +70 °C
Operating Temp. 0 to +60 °C
Humidity 5 to 90 % RH
Max. Operating Altitude ty 3.000 m
Max. Storage/Transit Altitude 10.000 m
Noise Level [db(A)] @ 1m <<40 (fanless design)
Lifetime
MTBF 50.000 h (without backlight)
Expansion Connector
Serial / USB USB / RS 232 /(TTL) internal
12
USB
10-pole Molex
USB Hub
2x Speaker
2-pole JST Audio
Amplifier
Audio
10-pole Molex
USB
Type A
Block Diagram SANTARO
i.MX6
Backlight
12-pole Molex
USB-OTG
Micro AB
SD-Card
Connector
I2C-3
USB H1
EIM
USDHC4
DRAM
SRAM
eMMC
DDR3L
Audio
Codec AUD4
MDIO/RMII
Keypad
20-pole JST Keypad
port
Res.Touch
4-pole Molex
SD2
Digital I/O
8-pole Molex
I/O
Driver GPIO
LVDS0
LVDS1
2x Display LVDS
20-pole Hirose
GPIO
PWM1_OUT
12V Supply
5V Supply
USB OTG
Touchscreen
Controller
Cap.Touch
4-pole Molex
HSIC
I2C-1 I²C
8-pole JST
24 V
2-pole Molex Step Down
Converter
PMIC Power
HDMI
Battery
RTC RC 1
FlexCAN-1
UART-1
FlexCAN-2
RS-232/MDB
10-pole Molex
RS-232
Transceiver
RS-232
Transceiver
UART-2
UART-5
HDMI
Type D
RJ-45
Jack
Ethernet
Phy
Battery
CR1220
CAN/RS-485
12-pole Molex
Galv. Isol.
x2 & x4
CAN
Transc.
CAN
Transc.
RS-485
Transc.
MDB
PRODUCT MANUAL
SANTARO
4.1 Block Diagram SBC
Pos. Description
1Ethernet (X24)
2Power (X1)
3Digital I/O (X14)
4CAN/RS-485 Interface (X39)
optional with galvanic isolation
5 Speaker (X9)
6Keypad/SPI (X21)
7RS-232/MDB (X13)
8USB Host (X34)
9USB OTG (X20)
10 Battery (X2/X112)
11 HDMI (X111) 13
(Exemplary Illustration. It shows the fully equipped SANTARO Dualcore 10.1 BX PCT.)
X9
PRODUCT MANUAL
SANTARO
4.2 Conectors
1 For the function of this switch please refer to the Flash N Go User Manual.
Pos. Description
12 Reset Switch (SW1)
13 Bootselect Switch (SW2)1
14 SD card reader (X31)
15 Power LED (D30)
14
(Exemplary Illustration both side)
PRODUCT MANUAL
SANTARO
Pos. Description
1
Ethernet
2
DC in
3
RS-232
4
USB-Device
5
USB Host (OTG)
Pos. Description
6
Reset sw
7
Bootselect sw
8
SD card slot
9
Power LED
Exemplary Illustration
15
Ethernet (TCP/IP) via
cross over cable or switch
USB Accessory
Memory stick,
mouse
RS-232 (Serial)
Debug-PC / Periphery
SD/SDHC
USB-OTG
2x RS232SPI/KeypadSpeakerCAN/RS485Digital I/O
Power
LAN USB-Host
X9
USB (Active Sync)
to PC / Development
PRODUCT MANUAL
SANTARO
5. Installation and Start Up
The content of this document is limited to explain the device connectors and how to access SANTARO via FTP over
your local area network (LAN) within a few seconds. For advanced hardware specications and software support,
please refer to chapter „3.3 Related Documents and Online Support“
5.1 Connection Scheme
https://support.garz-fricke.com/projects/Santaro/
Pin Name Description Information
1Tx+
Rx/Tx might be swapped
(Auto-MDIX)
+/- might be swapped
(Autom. polarity correction)
PoE might also be injected via Rx/Tx lines
2TX-
3RX+
4SPARE 1Power Supply (PoE)1
5
6RX-
7SPARE 2Power Supply (PoE)1
8
Header: RJ45
16
1
1
PRODUCT MANUAL
SANTARO
6. Internal and External Interfaces
6.1 Ethernet (X24)
Green LED (link) is default off and turns on when link is detected.
Yellow LED (act) flashes during sending/receiving packets.
1
Optional
Pin Name Description Level
1GND DC Ground 0 V
2Vcc_In DC Input voltage Nom. 9 to 32 V DC
Header: Molex 43045-0200 Micro-Fit 2p
Plug: Molex 43025-0200 Micro-Fit 2p,
crimp contact Molex 43030-0007
Shielding with 6,3 mm male spade terminal connector.
17
1
PRODUCT MANUAL
SANTARO
6.2 Power (X1)
Caution:
Power supplies connected to this device must be compliant to the requirements of
“limited power sources” (LPS) to prevent the end-user from danger in case of a fault.
Vin- 12
Vin+ 12
RV 1
S10K30
DC_IN
X1
MO LEX_43045-0200_Micro-Fit_02p
DC_IN
1 2
F2
5A_Nano_S lo-Blo_Typ-454
DC_IN
1 2
RV 2
CN1812K30G
n.b.
DC_ IN
6.3 Digital I/O (X14)
Pin Name Description Level
1DIG_IN1 Input 1 0 V
3-36 V
Low
High Typ. 8,3 mA / 24 V
2DIG_IN2 Input 2 0 V
3-36 V
Low
High Typ. 8,3 mA / 24 V
3GND_DIO Ground for digital IO group
4GND
Common ground, can be bridged
with GND_DIO, when galvanic
isolation is not required
5DIG_OUT1 Output 1 0V
Vcc_DIO
Low
High
Max. 800 mA /
24 V
6DIG_OUT2 Output 2
7Vcc_DIO Supply input for digital IO group <36 V, Nom. 9 to 32 V DC
8Vcc
Supply output, can be bridged with
Vcc_DIO, when galvanic isolation is
not required
Directly connected to the
supply (x1) without fuses
or surge protection!
Vcc_In
Header: Molex 43045-0800 Micro-Fit 8p
Plug: Molex 43025-0800 Micro-Fit 8p,
crimp contact Molex 43030-0007
Shielding with 6,3 mm male spade terminal connector
Digital I/O (X14) is not galvanic isolated from System-GND/Housing
18
1
5
1
5
PRODUCT MANUAL
SANTARO
Pin Name Description Level
1GND_CAN_RS485 Ground for CAN and RS485 group
2CAN1_TERM To enable CAN1-Termination, bridge with CAN1_H
3CAN1_H CAN bus 1 high -24 +24 V
4CAN1_L CAN bus 1 low -24 +24 V
5CAN1_TERM To enable CAN1-Termination, bridge with CAN1_L
6RS485_TERM To enable RS485-Termination: bridge with RS485_A
7GND_CAN_RS485 Ground for CAN and RS485 group
8n.a.
9RS485_Y TX+ -7 +12 V
10 RS485_Z TX- -7 +12 V
11 RS485_A RX+, to enable Half-Duplex: bridge with RS485_Y
12 RS485_B RX- ,to enable Half-Duplex: bridge with RS485_Z
Header: Molex 43045-1200 Micro-Fit 12p
Plug: Molex 43025-1200 Micro-Fit 12p, crimp contact Molex 43030-0007
Shielding with 6,3 mm male spade terminal connector
CAN/RS-485 (X39) is not galvanic isolated from System-GND/Housing
Pin Name Description Level
1-5 Identical to standard
6n.a.
7GND_CAN_RS485 Ground for CAN group
8CAN2_TERM To enable CAN2-Termination, bridge with CAN2_H
9CAN2_H CAN bus 2 high -24 +24 V
10 CAN2_L CAN bus 2 low -24 +24 V
11 CAN2_TERM To enable CAN2-Termination, bridge with CAN2_L
12 n.a.
19
1
7
1
7
1
7
1
7
1
7
1
7
1
7
PRODUCT MANUAL
SANTARO
6.4 CAN/RS-485 Interface (X39)
CAN1 / CAN2 *
* alternative assembly upon request
CAN1 Termination
RS485 Termination
RS485 Half-Duplex
CAN1 Termination
CAN2 Termination
Pin Name Description Level
1Speaker + Parallel to X10 1.5W RMS 8 Ohm
2Speaker -
Header: JST S2B-PH-SM3-TB
Plug: ST PHR-2 with crimp contacts SPH-002GW-P0.5L-ND
20
PRODUCT MANUAL
SANTARO
6.5 Speaker (X9)
1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

Seco SANTARO 19.0 SG Owner's manual

Category
POS terminals
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI