HDMI Extender Over
Network Cable
User Manual
Thank you for choosing our products.We focus on producing
professional, high-quality,cost-effective high-tech products,So you
can easily enjoy high-definition digital life brought by technology.
For the optimum performance and safety, please read these
instructions carefully before connecting, operating or adjusting the
product. And please keep this manual for future reference.
Introduction：
Long distance transmission of high definition signals is very
difficult because HDMI cable is very expensive and infrequent. This HDMI
extender breaks the problem of the expensive HDMI cable transmission
distance, simply use one network cat6/cat6a/cat7 cable in stead of HDMI
cable to extend HDMI signal to 60m , saving your money and space.
Features:
Supports HDMI 1.4
Follow standard IEEE-568B.
Can extend HDMI 4K@30HZ signal to 60m.
Support up to 20m cable length between the extender and the
source device when use HDMI/AWG26 cable.
Indicator LED can indicate the working status.
Allows you control a DVD player or other HDMI video source from
a remote location with the included IR cables.
Automatic adjustment to match cable length.
Installs in minutes. No need driver. Plug and play.
Specification：
Support HDCP Version..........................................HDCP1.2
Support HDMI Resolution..........................480i@60Hz, 480p@60Hz,
576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz,
1080p@50/60Hz,4K@30HZ
Transmit Length.........more than 60m by CAT6 Cable or higher level cable
Support Network Cable................................CAT6, CAT6A, CAT7
Power Supply.............................................DC5V 1A 2pcs
Support IR remote control....................................20-60Khz
Power Consumption.......................................TX: 2W; RX< 2W
Operating Temperature........................................0～60℃
Case Dimension.................................66.8x82.6x21.3mm*2pcs
Weight.....................................................105g*2pcs
Case Material..................................................Metal
Color..........................................................Black
Package Contents：
HDMI to RJ45 sender TX..........................................1pcs
RJ45 to HDMI receiver RX......................................1pcs
DC5V/1A Power Adapter..........................................2pcs
IR blaster extension cable.....................................1pcs
IR receiver extension cable...................................1pcs
User Manual...................................................1pcs
Diagram of Interfaces：
HDMI to RJ45
① DC 5V： DC 5V Power interface. Connect to power adapter.
② HDMI IN：HDMI Input Interface. Connect to computer, DVD and other
devices.
③ IR OUT： IR Signal Output Interface. Connect to included IR blaster
extension cable. Note:（ Do not connect headphone to this port to prevent
burning out the headphone.）
④ RESET： Reset Button.
⑤ CAT6： RJ45 output interface.
⑥ LINK： HDMI signal indicator LED. It lights on all the time with
HDMI signal input, flashes with no signal input.
RJ45 to HDMI
① RESET： Reset Button.
② CAT6： RJ45 input interface.
③ LINK： Connection status indicator LED. It lights on all the time
with HDMI signal transmission, flashes with no signal transmission.
④ DC 5V： DC 5V Power interface.Connect to power adapter.
⑤ HDMI OUT：HDMI Output Interface. Connect to TV, monitor and other
devices.
⑥ IR IN： IR Signal Input Interface. Connect to included IR receiver
extension cable. Note:（ Do not connect headphone to this port to prevent
burning out the headphone.）
Connection and Operation：
IMPORTANT SAFETY INSTRUCTIONS：
1.Do not mix up HDMI to RJ45 sender and RJ45 to HDMI receiver before
installation.
2.Do not hot plug when it is working.
3.Use DC 5V power supply only. Make sure specification matched if using
power adapters not supplied by factory.
Installation steps:
1.Use HDMI cable to connect the HDMI source device(computer graphics card,
DVD, PS3, HD monitoring equipment etc) to the HDMI input interface of
the HDMI to RJ45 sender(TX).
2.Use HDMI cable to connect the HDMI display device like SDTV, HDTV,
projector with HDMI port to the HDMI output interface of the RJ45 to HDMI
receiver(RX).
3.Use UTP/STP cat6/cat6A/cat7 cable to connect RJ45 output interface of
the TX to the RJ45 input interface of the RX.
4.Connect the IR blaster extension cable to the IR OUT interface of the
TX and put the IR blaster in front of the DVD that need to be controlled.
5.Connect the IR receiver extension cable to the IR IN interface of the
RX and put the IR receiver in front of the TV.
6.Connect the TX and RX to the DV 5V power supply.
UTP/STP cat6/ cat6A/ cat7 cable follows standard IEEE-568B: 1-ORANGE/
WHITE 2-ORANGE 3-GREEN / WHITE 4-BLUE 5-BLUE/WHITE 6-GREEN 7-BROWN/WHITE
8-BROWN
Note：
Please use the machine as the instruction listed to keep the long lifetime
of it.
1.Please do not expose this unit to the damp, high-temperature, dusty,
erosive, or oxidative environment.
2.All parts will be free from the strong shake, hit, fall.
3.Please do not touch the power adapter plug with wet hands.
4.Please hold the plug when unplugging. Do not pull the power cable
directly.
5.Please turn off power when the item is not in use.
6.Please do not open the cover and do not touch the inside parts.
FAQ：
Please check all the cables carefully before installation and make sure
all the interfaces are connected correctly. The common problems and the
relevant solutions are showed as follows.
No
Problem
Description
Solutions
1
No Image Output
Adjust RX “RESET” button
2
RX “LINK” led is
flashing all the
time.
Make sure network cable connection
follows the way of 568B; Check whether TX
has HDMI signal Input; Reset TX or RX.
3
RX “ LINK ” led
lights on all the
time but no image
output
Adjust RX “RESET” button; Make sure HDMI
cable is well connected with TV; Reconnect
the network cable and power on the
receiver again.
/
