3com 3C16850 Installation guide

http://www.3com.com/

Switch 7700

Installation Guide

Version 3.0

3C16850 7-slot Starter Kit

3C16852 8-slot Starter Kit

3C16870 4-slot Starter Kit

and associated modules

Part No. 10014180

Document Number: DUA1685-0AA02

Published November 2004

3Com Corporation

350 Campus Drive

Marlborough, MA

01752-3064

in any form or by any means or used to make any derivative work (such as translation, transformation, or

adaptation) without written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time

to time without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either

implied or expressed, including, but not limited to, the implied warranties, terms or conditions of

merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or

changes in the product(s) and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license

agreement included with the product as a separate document, in the hard copy documentation, or on the

removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy,

please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein

are provided to you subject to the following:

All technical data and computer software are commercial in nature and developed solely at private expense.

Software is delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995)

or

as a “commercial item” as defined in FAR 2.101(a) and as such is provided with only such rights as are

provided in 3Com’s standard commercial license for the Software. Technical data is provided with limited

rights only as provided in DFAR 252.227-7015 (Nov

1995) or FAR 52.227-14 (June 1987), whichever is

applicable. You agree not to remove or deface any portion of any legend provided on any licensed program

or documentation contained in, or delivered to you in conjunction with, this User Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may

not be registered in other countries.

3Com and the 3Com logo are registered trademarks of 3Com Corporation.

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and

Windows NT are registered trademarks of Microsoft

Corporation. UNIX is a registered trademark in the

United States and other countries, licensed exclusively through X/Open Company, Ltd.

IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Inc.

All other company and product names may be trademarks of the respective companies with which they are

associated.

ENVIRONMENTAL STATEMENT

It is the policy of 3Com Corporation to be environmentally-friendly in all operations. To uphold our policy,

we are committed to:

Establishing environmental performance standards that comply with national legislation and regulations.

Conserving energy, materials and natural resources in all operations.

Reducing the waste generated by all operations. Ensuring that all waste conforms to recognized

environmental standards. Maximizing the recyclable and reusable content of all products.

Ensuring that all products can be recycled, reused and disposed of safely.

Ensuring that all products are labelled according to recognized environmental standards.

Improving our environmental record on a continual basis.

End of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of all end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting material.

Environmental Statement about the Documentation

The documentation for this product is printed on paper that comes from sustainable, managed forests; it is

fully biodegradable and recyclable, and is completely chlorine-free. The varnish is environmentally-friendly,

and the inks are vegetable-based with a low heavy-metal content.

CONTENTS

ABOUT THIS GUIDE

Conventions 7

Related Documentation 8

SWITCH 7700 COMPONENTS

Switch Chassis 9

Switch Backplane 9

Fabric Module 10

Submodule Slot 11

Reset Button 11

Fixed Ports 11

Module LEDs 12

Power LEDs 13

Fan LED 13

Fabric 32 Submodules 13

4-Port 1000BASE-X-GBIC Submodule 13

4-Port 10/100/1000BASE-T Submodule 14

I/O Modules 15

48-port 10/100BASE-T Auto-sensing FE Module 15

8-port 1000BASE-X GE Module 16

8-port 10/100/1000BASE-T GE Module 18

24-port 100BASE-FX MMF FE Module 19

20-Port 10/100/1000BASE-T Module 20

20-Port 1000BASE-X-SFP Module 22

1-Port 10GBASE-R-XENPAK Module 23

Power Module 24

Fan Assembly 25

Switch 7700 Specifications 26

Switch 7700 Software Features 27

INSTALLING THE SWITCH 7700

Preparing to Install 29

General Safety Recommendations 29

Electrical Safety 30

Moving the Switch 30

Laser Safety 30

General Site Requirements 30

Installation Space 31

Installation Checklist 31

Installing the Chassis 32

Installing in a Standard Cabinet 32

Installing on a Workbench 32

Installing the Cabling Rack 32

Installing a Module 33

Installing a Submodule 33

Connecting the Ground Wire 34

Connecting and Configuring Power 34

Connecting AC Power Cords 34

Connecting DC Power Cords 35

Configuring AC Power Sources 35

Installing the Fan Assembly 36

Installing Cables 36

Connecting the Console Cable 36

Connecting the AUX Cable 36

Connecting Module Cables 37

Installing Cabling 38

Bench-Mounted Switch 38

Rack-Mounted Switch 38

Cable Binding 38

Post-installation Checklist 39

CONFIGURING THE SWITCH 7700

Configuring the Switch 7700 and a Local Terminal 41

Setting Terminal Parameters 41

Booting the Switch 7700 44

Powering up and Booting 45

MAINTAINING SOFTWARE

Upgrading Software 47

Upgrading the Software Image 47

Upgrading an 8-Slot Chassis 47

Upgrading Software with FTP 48

Upgrading Software Using The BOOT Menu 49

Upgrading Software Using Xmodem 53

Upgrading Software Using TFTP 55

Lost Passwords 55

Using the BOOT Menu 55

MAINTAINING HARDWARE

Replacing a Power Module 57

Removing the AC Power Module 57

Installing the AC Power Module 57

Replacing a Power Supply 58

Replacing I/O Modules 59

Replacing the Fan Assembly 59

TROUBLESHOOTING

Troubleshooting the Configuration 61

No information is displayed on the terminal 61

The displayed characters are illegible 61

Troubleshooting Power 61

Troubleshooting the Fan 62

Troubleshooting the Modules 62

SWITCH 7700 CABLES

Console Cable 63

AUX Cable 63

Electrical Port Connector 64

Optical Fiber Cable Connectors 65

OBTAINING SUPPORT FOR YOUR SWITCH

Register Your Product to Gain Service Benefits 67

Purchase Value-Added Services 67

Troubleshoot Online 67

Access Software Downloads 67

Contact Us 68

Telephone Technical Support and Repair 68

ABOUT THIS GUIDE

This guide describes the 3Com

®

Switch 7700 and how to install hardware,

configure and boot software, and maintain software and hardware. This guide

also provides troubleshooting and support information for your switch.

This guide is intended for Qualified Service personnel who are responsible for

configuring, using, and managing the switches. It assumes a working knowledge

of local area network (LAN) operations and familiarity with communication

protocols that are used to interconnect LANs.

Always download the Release Notes for your product from the 3Com World Wide

Web site and check for the latest updates to software and product

documentation:

http://www.3com.com

Conventions Table 1 lists icon conventions that are used throughout this guide.

Table 2 lists text conventions that are used throughout this guide.

Table 1 Notice Icons

Icon Notice Type Description

Information note Information that describes important features or

instructions.

Caution Information that alerts you to potential loss of data

or potential damage to an application, system, or

device.

Warning Information that alerts you to potential personal

injury.

Tab le 2 Text Conventions

Convention Description

Screen displays This typeface represents information as it appears on the

screen.

Keyboard key names If you must press two or more keys simultaneously, the key

names are linked with a plus sign (+), for example:

Press Ctrl+Alt+Del

The words “enter” and “type” When you see the word “enter” in this guide, you must type

something, and then press Return or Enter. Do not press

Return or Enter when an instruction simply says “type.”

8 ABOUT THIS GUIDE

The following manuals offer additional information necessary for managing your

Switch 7700:

■ Switch 7700 Command Reference Guide — Provides detailed descriptions of

command line interface (CLI) commands, that you require to manage your

Switch 7700.

■ Switch 7700 Configuration Guide— Describes how to configure your Switch

7700 using the supported protocols and CLI commands.

■ Switch 7700 Release Notes — Contains the latest information about your

product. If information in this guide differs from information in the release

notes, use the information in the Release Notes.

These documents are available in Adobe Acrobat Reader Portable Document

Format (PDF) on the CD-ROM that accompanies your router or on the 3Com

World Wide Web site:

http://www.3com.com/

Words in italics Italics are used to:

Emphasize a point.

Denote a new term at the place where it is defined in the

text.

Identify menu names, menu commands, and software

button names.

Examples:

From the Help menu, select Contents.

Click OK.

Words in bold Boldface type is used to highlight command names. For

example, “Use the display user-interface command

to...”

Table 2 Text Conventions

Convention Description

1

SWITCH 7700 COMPONENTS

The chapter describes the following Switch 7700 components:

■ Switch Chassis

■ Switch Backplane

■ Fabric Module

■ Fabric 32 Submodules

■ I/O Modules

■ Power Module

■ Fan Assembly

■ Switch 7700 Specifications

■ Switch 7700 Software Features

Switch Chassis There are three Switch 7700 Models, the 4-Slot, 7-Slot, and the 8-Slot. Table 3 lists

the hardware features of each model.

Switch Backplane The Switch 7700 backplane is part of the integrated chassis and delivers

high-speed data transfer between the Fabric and I/O modules. The backplane

bandwidth capacity is 120 Gbps.

The backplane supports the following functions:

■ Interconnection of signals between modules

■ Provides communication channels

■ Hot swapping for modules

■ Auto-recognition of slots

■ Distribution of power and management of the power supply for the system

Tab le 3 Hardware Features of the Switch 7700 Models

4-Slot Chassis 7-Slot Chassis 8-Slot Chassis

Fabric slots 1 1 2

I/O module slots 3 6 6

Fan slot 1 1 1

AC Power module

slots

2 3 3

10 CHAPTER 1: SWITCH 7700 COMPONENTS

Fabric Module There are two Fabric modules for the Switch 7700:

■ Fabric 64 (3C16857 or 3C16857R)

■ Fabric 32 (3C16872)

The Fabric 64 and Fabric 32 are not interchangeable. You can install the Fabric 32

only in a 4-slot chassis. You can install the Fabric 64 only in the 7- or 8-slot chassis

The Fabric module is the core of Switch 7700 system. It has the following

functions:

■ Connects the I/O modules through the backplane and forwards Layer 2 and

Layer 3 data

■ Manages and calculates routing

■ Performs the switch’s software upgrade and system reset functions

■ Monitors system power and the fan frame

Figure 1 illustrates the front panel of the Fabric 64.

Figure 1 Fabric 64

1 Reset button

2 Console port

3 Ethernet port

4 Ethernet port LEDs

5 Fan LEDs

6 Power module LEDs

7 I/O module LEDs

Figure 2 illustrates the front panel of the Fabric 32.

Figure 2 Fabric 32

1 Submodule slot

2 Console port

3 Ethernet port

4 Ethernet port LEDs

5 Fan LEDs

6 Power LEDs

7 I/O module LEDs

8 Reset button

3C16857

1234

56

7

3C16872

1234567

8

Fabric Module 11

Table 4 lists Fabric specifications.

Submodule Slot The submodule slot in the Fabric 32 offers extended Ethernet capacity using the

following submodules:

■ 4-port 1000BASE-X-GBIC submodule

■ 4-port 10/100/1000BASE-T submodule

For more information on these submodules, see “Fabric 32 Submodules”on

page 13.

Reset Button The reset button resets the entire system.

Fixed Ports The Switch 7700 Fabric module provides the following fixed ports:

■ Console Port

■ Ethernet Port

Console Port

The console port is connected to the configuration terminal using an RJ-45

connector. You can use the console port for system debugging, configuration,

maintenance, management, and loading application files.

The console port can also be connected to a modem for functions such as remote

system debugging, configuration, maintenance, and management. You can

configure the baud rate on the console port.

Table 5 lists console port specifications.

Tab le 4 Fabric Specifications

Item Fabric 64 (3C16857 or 3C16857R) Fabric 32 (3C16872)

Bandwidth 64 Gbps 32 Gbps

CPU MPC8260 200 Mhz

BootROM 1 MB

SDRAM 256 MB

Flash 16 MB

Submodule slot 1

Dimensions (L x W) 366.7 mm x 340 mm (14.5 x 13.5 in)

External ports One console port that supports local and remote dial-up configuration

management of the switch.

One 10BASE-T/100BASE-TX port for upgrade and network management

Maximum power

consumption

80 W 70 W (with submodule)

Tab le 5 Console Port Specifications

Specification Description

Port connector RJ-45

Port standard Asynchronous EIA/TIA-232

12 CHAPTER 1: SWITCH 7700 COMPONENTS

Ethernet Port

The Ethernet port on the Fabric is connected to a computer using an RJ-45

connector. You can use the Ethernet port for system application downloading and

debugging. The Ethernet port can also be connected to devices such as a network

management workstation to manage the system remotely.

Table 6 lists Ethernet port specifications.

See “Electrical Port Connector” on page 64 for an illustration of the RJ-45

connector and MDI/MDI-X pinout details.

Table 7 describes the LEDs of the Ethernet port.

Module LEDs The module LEDs show the status of the I/O modules, as described in Table 8.

Baud rate 9600 bps (by default)

Transmission distance 15 m (45 ft)

Services Connects with character terminal

Connects with local or remote PC serial port and runs terminal

emulation on a PC (a pair of modems are required for a

remote connection)

Tabl e 6 Ethernet Port Specifications

Specification Description

Port connector RJ-45

Number of port(s) 1

Port speed 10 Mbps, half/full duplex

100 Mbps, half/full duplex

MDIX

Cable and maximum transmission

distance

Category-5 twisted pair for transmission within 100 m

(300 ft)

Port function Switch software upgrade and network management

Tabl e 7 Ethernet Port LEDs

LED Description

LINK Off — The line is not connected.

Green — The line is connected.

ACTIVE Green — No data is being transmitted.

Green flashing — Data is being transmitted.

Table 5 Console Port Specifications (continued)

Specification Description

Tabl e 8 I/O Module LEDs

LED Status description

RUN Green or off — The module failed or has not been inserted.

Green flashing — The module is working normally.

ALM Off — The module is working normally or has not been

inserted.

Green or green flashing — The module failed or is not

working normally.

Fabric 32 Submodules 13

Power LEDs PWR1, PWR2, and PWR3 LEDs show the status of the power modules, as

described in

Table 9.

Fan LED Fan LEDs show the status of the fan frame, as described in Table 10.

Fabric 32 Submodules The Fabric 32 provides a slot for one submodule. The Fabric 32 supports the

following submodules:

■ 4-Port 1000BASE-X-GBIC Submodule (3C16874)

■ 4-Port 10/100/1000BASE-T Submodule (3C16873)

4-Port 1000BASE-X-GBIC

Submodule

The 4-port 1000BASE-X-GBIC submodule provides four GE full-duplex Ethernet

GBIC ports.

Figure 3 illustrates the 4-port 1000BASE-X-GBIC submodule.

Figure 3 4-Port 1000BASE-X-GBIC Submodule

Ethernet GBIC port

2 Ethernet GBIC port LED

Table 11 describes the 4-port 1000BASE-X-GBIC submodule LEDs.

Tab le 9 Power LEDs

LED Description

OK Green — The corresponding power module work is working

normally.

Off — The corresponding power module is not working or

has not been installed.

FAIL Green — The corresponding power module is not working.

Off — The corresponding power module works normally or

has not been installed.

Tab le 10 Fan LEDs

LED Description

OK Green — The fan is working normally.

Off — The fan is not working or has not been installed.

FAIL Green — The fan is not working.

Off — The fan is working normally or has not been installed.

Tab le 11 4-Port 1000BASE-X-GBIC Submodule LEDs

LED Description

LINK/ACT Green — The link is operating normally.

Off — The link is not operating.

Green flashing — Data is being transmitted.

3C16874

12

14 CHAPTER 1: SWITCH 7700 COMPONENTS

Table 12 lists the specifications for each of the 4-port 1000BASE-X-GBIC

submodule.

4-Port

10/100/1000BASE-T

Submodule

The 4-Port 10/100/1000BASE-T submodule provides four 10/100/1000 Mbps

auto-negotiation service ports.

Figure 4 illustrates the 4-port 10/100/1000BASE-T submodule.

Figure 4 4-Port 10/100/1000BASE-T Submodule

1 Ethernet port

2 Ethernet port LEDs

Table 13 describes the 4-port 10/100/1000BASE-T submodule LEDs.

Table 14 lists specifications of the 4-port 10/100/1000BASE-T submodule.

Tabl e 12 4-Port 1000BASE-X-GBIC Submodule Specifications

Optional GBIC

Module

Central

Wavelength

Connector

Type

Interface Fiber

Specifications

Max.

Transmission

Distance

1000BASE-SX-MM

(3CGBIC91)

850 nm SC 50/125 µm

multi-mode fiber

62.5/125 µm

Multi-mode fiber

500 m (1640 ft)

220 m (722 ft)

1000BASE-LX-SM-IR

(3CGBIC92)

1310 nm SC 9/125 µm

Single-mode fiber

10 km (6 mi)

1000BASE-LX-SM

(3CGBIC97)

1550 nm SC 9/125 µm

Single-mode fiber

40 km (25 mi)

70 km (43.5 mi)

Tabl e 13 4-Port 10/100/1000BASE-T Submodule LEDs

LED Description

LINK Off — The link is not operating.

On — The link is operating normally.

ACT Off — No data is being transmitted.

Green flashing — Data is being transmitted.

Tabl e 14 4-Port 10/100/1000BASE-T Submodule Specifications

Specification Description

Connector type RJ-45

Number of ports 4

Port speed 1000 Mbps full duplex

100 Mbps half/full duplex

10 Mbps half/full duplex

MDI/MDI-X auto-sensing

Cable and maximum

transmission distance

Category 5 twisted pair up to 100 m (328 ft)

3C16873

12

I/O Modules 15

See “Electrical Port Connector” on page 64 for an illustration of the RJ-45

connector and MDI/MDI-X pinout details.

I/O Modules The Switch 7700 provides slots for three or six modules below the Fabric slots. The

following I/O modules are supported:

■ 48-port 10/100BASE-T Auto-sensing FE Module (3C16860)

■ 8-port 1000BASE-X GE Module (3C16858)

■ 8-port 10/100/1000BASE-T GE Module (3C16859)

■ 24-port 100BASE-FX MMF FE Module (3C16861)

■ 20-Port 10/100/1000BASE-T Module (3C16863)

■ 20-Port 1000BASE-X-SFP Module (3C16862)

■ 1-Port 10GBASE-R-XENPAK Module (3C16875)

Consider the following when selecting I/O modules:

■ You can configure several I/O modules of the same type

■ All I/O module slots are the same and any combination of I/O modules can be

inserted

■ You must select I/O module port cables that are compatible with each installed

I/O module

48-port 10/100BASE-T

Auto-sensing FE Module

The 48-port 10/100BASE-T Auto-sensing FE module provides 48 external

100Mbps Ethernet electrical ports.

Figure 5 illustrates the 48-port 10/100BASE-T Auto-sensing FE module.

Figure 5 48-port 10/100BASE-T Auto-sensing FE Module

Figure 6 illustrates the front panel and LEDs of the 48-port 10/100BASE-T

Auto-sensing FE module.

Figure 6 Front Panel of the 48-Port 10/100BASE-T Auto-sensing FE module

12

16 CHAPTER 1: SWITCH 7700 COMPONENTS

1 Ethernet port

2 Ethernet port LED

Each 100 Mbps Ethernet port has a green LED, indicating LINK/ACTIVE status.

Table 15 describes the 48-port 10/100BASE-T Auto-sensing FE module LED.

Table 16 describes the specifications of the 48-port 10/100BASE-T Auto-sensing FE

module.

See “Electrical Port Connector” on page 64 for an illustration of the RJ-45

connector and MDI/MDI-X pinout details.

8-port 1000BASE-X GE

Module

The 8-port 1000BASE-X GE module provides 8 external GBIC module ports. A

GBIC module is used for each data receiving/transmitting channel. The following

modules are available:

■ 3CGBIC91

■ 3CGBIC92

■ 3CGBIC97

Figure 7 illustrates the 8-port 1000BASE-X GE module.

Tabl e 15 48-Port 10/100BASE-T Auto-sensing FE module LED

LED Description

LINK/ACT Green — The port is connected

Off — The port is not connected

Green flashing — Data is being transmitted

Tabl e 16 Specifications for the 48-Port 10/100BASE-T Auto-sensing FE Module

Specification Description

CPU MPC850

BootROM 512 KB

SDRAM 64 MB

Dimensions (L X W) 366.7 x 340 mm (14.5 x 13.4 in)

Maximum power

consumption

55 W

Connector RJ-45

Number of ports 48

Port transmission

speed

10 Mbps half/full duplex

100 Mbps half/full duplex

MDI/MDIX auto-sensing

Cables and maximum

transmission distance

Cables are 2 100-ohm Category-5 twisted pairs up to 100 m (300 ft).

Compliance IEEE802.3

IEEE802.3u

IEEE802.3x

I/O Modules 17

Figure 7 8-Port 1000BASE-X GE Module

Every GBIC port has a LED, as shown in Figure 8.

Figure 8 Front Panel of the 8-Port 1000BASE-X GE Module

1 GBIC port

2 GBIC port LED

Table 17 describes the 8-Port 1000BASE-X (GBIC) GE module LED.

The cables for each of the supported 8GBIC modules are described inTable 18.

Table 19 describes the specifications of the 8-port 1000BASE-X GE module.

Tab le 17 8-Port 1000BASE-X (GBIC) GE Module LED

LED Description

LINK Off — The link is not connected

Green — The link is connected

ACT Off — No data is being transmitted

Green flashing — Data is being transmitted or received

Tab le 18 GBIC Module Port Cables

GBIC Module Type Central Wave Length

3CGBIC91 850 nm

3CGBIC92 1550 nm

3CGBIC97 1550 nm

Tab le 19 Specifications for the 8-Port 1000BASE-X GE Module

Specification Description

CPU MPC850

3C16858

12

18 CHAPTER 1: SWITCH 7700 COMPONENTS

8-port

10/100/1000BASE-T GE

Module

The 8-port 10/100/1000BASE-T GE module provides 8 external 10/100/1000

Mbps auto-sensing Ethernet electrical ports.

Figure 9 illustrates the 8-port 10/100/1000BASE-T GE module.

Figure 9 8-Port 10/100/1000BASE-T GE Module

Each port on the 8-port 10/100/1000BASE-T GE module has 2 LEDs, as shown in

Figure 10.

Figure 10 Front Panel of the 8-Port 10/100/1000BASE-T GE Module

1 Ethernet port

2 Ethernet port LEDs

BootROM 512 KB

SDRAM 64 MB

Dimensions (L x W) 366.7 x 340 mm (14.5 x 13.4 in)

Maximum power

consumption

50 W

Number of ports 8

Optional GBIC module

types

3CGBIC 91

3CGBIC 92

3CGBIC 97

Port transmission speed 1000 Mbps, full duplex

Compliance IEEE 802.3z

IEEE 802.3x

Table 19 Specifications for the 8-Port 1000BASE-X GE Module (continued)

Specification Description

12

I/O Modules 19

Table 20 describes the LEDs on the 8-port 10/100/1000BASE-T GE module.

Specifications of the 8-port 10/100/1000BASE-T GE module are described in

Table 21.

24-port 100BASE-FX

MMF FE Module

The 24-port 100BASE-FX MMF FE module provides 24 100 Mbps multi-mode

Ethernet optical port service channels.

Figure 11 illustrates the 24-port 100BASE-FX MMF FE module.

Figure 11 24-Port 100BASE-FX MMF FE Module

Tab le 20 8-Port 10/100/1000BASE-T GE Module LEDs

LED Description

LINK Off — The link is not connected

Green — The link is connected

ACT Off — No data is being transmitted

Green flashing — Data is being transmitted or received

Tab le 21 Specifications for the 8-Port 10/100/1000BASE-T GE Module

Specification Description

CPU MPC850

BootROM 512 Kb

SDRAM 64 MB

Dimensions (L x W) 366.7 x 340 mm (14.5 x 13.4 in)

Maximum power consumption 50 W

Connector type RJ-45

Number of ports 8

Port transmission speed 10 Mbps, half/full duplex

100 Mbps, half/full duplex

1000 Mbps, full duplex

Cables and maximum

transmission distance

4 100-ohm Category-5 non-shielded twisted pairs up to 100

m (300 ft).

Compliance IEEE 802.3ab

IEEE802.3

IEEE802.3u

IEEE802.3x

20 CHAPTER 1: SWITCH 7700 COMPONENTS

Each 100 Mbps optical port has a green LED, as shown in Figure 12.

Figure 12 Front Panel of the 24-Port 100BASE-FX MMF FE Module

1 Ethernet port

2 Ethernet port LED

Table 22 describes the status of the 24-port 100BASE-FX MMF FE module LEDs.

The 24-port 100BASE-FX MMF FE module requires a 62.5/125 µm multi-mode

optical fiber cable with an MT-RJ connector and a central wavelength of 1300 nm.

Table 23 describes the specifications of the 24-port 100BASE-FX MMF FE module.

20-Port

10/100/1000BASE-T

Module

The 20-Port 10/100/1000BASE-T module provides 20 10/100/1000BASE-T

auto-sensing Ethernet ports.

Figure 13 illustrates the 20-Port 10/100/1000BASE-T Module.

Tabl e 22 24-Port 100BASE-FX MMF FE Module LEDs

LED Description

LINK/ACT Green — The port is connected.

Off — The port is not connected.

Green flashing — Data is being transmitted or received.

Tabl e 23 Specifications for the 24-Port 100BASE-FX MMF FE Module

Specification Description

CPU MPC850

BootROM 512 KB

SDRAM 64 MB

Dimensions (L x W) 366.7 x 340 mm (14.5 x 13.4 in)

Maximum power

consumption

55 W

Connector type MT-RJ

Number of ports 24

Port transmission speed 100 Mbps, full-duplex

Cables and maximum

transmission distance

62.5/125 µm multi-mode optical fiber up to 2 km (1.3 mi)

Compliance IEEE 802.3

IEEE 802.3i

IEEE 802.3u

IEEE 802.3x

1

2

Page is loading ...

3com 3C16850 Installation guide

This manual is also suitable for

3com 3C16850 Installation guide

Related papers

Other documents