Chapin 63980 User manual

Brand: Chapin

Model: 63980

Type: User manual

This manual is also suitable for

63985

Model 63985 • 4G/ 15L

013723 R0115

Carefully Read These Instructions Before Use

WARNING

DO NOT RETURN THIS

SPRAYER TO STORE

Call: 1-800-950-4458

www.chapinmfg.com

Use and Care Manual

BackpackBackpack

SprayerSprayer

ProSeriesProSeries

™

Chapin International, Inc

P.O. Box 549

700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458

www.chapinmfg.com

WARNING

WARNING: Handling the brass parts of this product will expose you to lead, a chemical

known to the State of California to cause birth defects and other reproductive harm.

Wash hands after handling.

CAUTION

WARNING: Improper use or failure to follow instructions can result in explosive

failure causing serious eye or other injury. For safe use of this product you must read

and follow all instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause

pressure build-up resulting in possible explosion. Do not store or leave solution in tank after

use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when

spraying. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s

original parts. Never spray ammable, caustic, acidic, chlorine, bleach or other

corrosive solutions or heat, pressure, or gas producing chemicals. Always read

and follow chemical manufacturer’s instructions before use with this sprayer as

some chemicals may be hazardous when used with this sprayer.

• PRE-USE CHECK: Before each use check tightness of hose nut to be sure hose is

securely attached to the shut-off assembly. Insure that all nozzle and wand

connections are tight.

• Do Not exceed a tank solution temperature of 120º F/ 49º C.

NOTE: The tank and hose may have residual water in it due to quality testing

performed on the sprayer.

WARNING

This sprayer is designed to operate with a Black & Decker 20V Lithium Ion battery ONLY.

Any other batteries could cause serious harm or injury to the operator and serious damage to

the sprayer.

WARNING: For safe operation, read this manual before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack and

charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS

• Donotincineratethebatterypackevenifitisseverelydamagedoriscompletelyworn

out. The battery pack can explode in a ﬁre. Toxic fumes and materials are created when battery packs

are burned.

• DoNotchargeorusebatteryinexplosiveatmospheres,suchasinthepresenceof

ammableliquids,gasesordust. Inserting or removing the battery from the charger may ignite the

dust or fumes.

• Ifbatterycontentscomeintocontactwiththeskin,immediatelywashareawithmild

soapandwater. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or

until irritation ceases. If medical attention is needed, the battery electrolyte for Lithium-Ion batteries is

composed of a mixture of liquid organic carbonates and lithium salts.

• Contentsofopenedbatterycellsmaycauserespiratoryirritation. Provide fresh air. If

symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be ﬂammable if exposed to spark or ﬂame.

• Charge the battery packs only in Black&Decker chargers.

•DONOTsplashorimmerseinwaterorotherliquids. This may cause premature cell failure.

•Donotstoreorusethetoolandbatterypackinlocationswherethetemperaturemay

reachorexceed105ºF(40ºC)(suchasoutsideshedsormetalbuildingsinsummer).

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or

damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery

pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e.,

pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to

service center for recycling.

WARNING:Firehazard.Donotstoreorcarrybatterysothatmetalobjectscancontact

exposedbatteryterminals. For example, do not place battery in aprons, pockets, tool boxes, product

kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transportingbatteriescanpossiblycauseresifthebatteryterminalsinadvertentlycome

incontactwithconductivematerialssuchaskeys,coins,handtoolsandthelike.The US

Department of transportation Hazardous Material Regulations (HMR) actually prohibit transporting

batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they

are properly protected from short circuits. So when transporting individual batteries, make sure that the

battery terminals are protected and well insulated from materials that could contact them and cause a

short circuit. NOTE:Lithium-Ionbatteriesshouldnotbeputincheckedbaggage.

STORAGERECOMMENDATIONS

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.

2. Long storage will not harm the battery pack or charger.

CHARGINGPROCEDURE

Black&Deckerchargers are designed to charge

Black&Deckerbattery packs in 3.5-4 hours depending

on the pack being charged.

1. Plug the charger into an appropriate outlet before inserting the

battery pack.

2. Insert the battery pack into the charger as shown in gureA.

3. The green LED will ﬂash indicating that the battery is being charged.

4. The completion of charge is indicated by the green LED remaining on continuously. The pack is fully

charged and may be used at this time or left on the charger.

IMPORTANTCHARGINGNOTES

1. Longest life and best performance can be obtained if the battery pack is charged when the

air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent

serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal

condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment such as

in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance.

b. Check to see if receptacle is connected to a light switch which turns power off when you turn out

the lights.

c. Move charger and battery pack to a location where the surrounding air temperature is

approximately 65°F and 75°F (18°- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your local service center.

4. The battery pack should be recharged when it fails to produce sufﬁcient power on jobs which

were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging

procedure. You may also charge a partially used pack whenever you desire with no adverse affect

on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or

any buildup of metallic particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING:Shockhazard. Do not allow any liquid to get inside charger. Never attempt to open the

battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a

service center for recycling.

INSTALLINGANDREMOVINGTHEBATTERYPACK

FROMTHESPRAYER

WARNING:Make sure switch is in the off position.

TO INSTALL BATTERY PACK: Insert battery pack into

tool until an audible click is heard (Figure B). Make

sure battery pack is fully seated and latched into

position.

TOREMOVETHEBATTERYPACK: Depress the

battery release button as shown in Figure C and pull

battery pack out of tool.

Rechargedischargedbatteriesassoonaspossibleafteruseorbatterylifemaybegreatly

diminished.Forlongestbatterylife,donotdischargebatteriesfully. Itisrecommendedthat

thebatteriesberechargedaftereachuse.

LEAVINGTHEBATTERYINTHECHARGER

The charger and battery pack can be left connected with the green LED glowing indeﬁnitely. The charger

will keep the battery pack fresh and fully charged.

SAVE THESE INSTRUCTIONS

•Pullbyplugratherthancordwhendisconnectingcharger.This will reduce risk of damage to

electric plug and cord.

• Makesurethatcordislocatedsothatitwillnotbesteppedon,trippedover,orotherwise

 subjectedtodamageorstress.

•Donotuseanextensioncordunlessitisabsolutelynecessary.Use of improper extension

cord could result in risk of ﬁre, electric shock, or electrocution.

•Anextensioncordmusthaveadequatewiresize(AWGorAmericanWireGauge)for

 safety. the smaller the gauge number of the wire, the greater the capacity of the cable, that is 16

gauge has more capacity than 18 gauge. When using more than one extension to make up the

total lenght, be sure each idividual extension contains at least the minimum wire size.

•Donotoperatechargerwithdamagedcordorplug - have them replaced immediately.

•Donotoperatechargerifithasreceivedasharpblow,beendropped,orotherwise

 damagedinanyway. Take it to an authorized service center.

•Donotdissassemblecharger;take it to an authorized service center when service or repair is

required. Incorrect reassembly may result in a risk of electric shock electrocution or ﬁre.

•Disconnectthechargerfromtheoutletbeforeattemptinganycleaning. This will reduce the

risk of electric shock. Removing the battery pack will not reduce the risk.

•NEVERattempttoconnect2chargerstogether.

•Thechargerisdesignedtooperateonstandardhouseholdelectricalpower(120Volts).Do

 notattempttouseitonanyothervoltage.

Symbols

The label on your tool may include the following symbols.

volts

Hz hertz

min minutes

direct current

Class I Construction

(grounded)

Class II Construction

( double insulated)

Read instruction

manual before use

Use proper eye protection

amperes

watts

alternating current

no load speed

earthing terminal

safety alert symbol

/min or rpm revolutions or

reciprocation per minute

Use proper

respiratory protection

Use proper hearing protection

SAVETHESEINSTRUCTIONS:This manual contains important safety instructions for battery

chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery pack, and

product using battery pack.

WARNING:Shockhazard.Do not allow any liquid to get inside charger.

CAUTION:Burnhazard.To reduce the risk of injury, charge only designated Black&Decker

batteries. Other types of batteries my burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged into the power supply, the charger

can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited

to, steel wool, aluminum foil, or any build up of metalic partices should be kept away from charger

cavities. Always unplug the charger from the power supply when there is no battery pack in the

cavity. Unlplug charger before attempting to clean.

WARNING:DONOTattempttochargethebatterypackwithanychargersotherthanthe

onesinthismanual. The charger and battery pack are speciﬁcally designed to work together.

•ThesechargersarenotintendedforanyusesotherthanchargingdesignatedBlack

&Deckerrechargeablebatteries. Any other uses may result in risk of ﬁre, electric shock or

electrocution.

•Donotexposechargertorainorsnow.

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

1. Poly

Nozzle Cap

2. Retaining

Nut

3. Nozzle

Body

4. Nozzle

Gasket

5. Elbow

Figure 3Figure 2Figure 1

1. Brass

Nozzle Cap

2. Retaining

Nut

3. Nozzle

Body

4. Nozzle

Gasket

5. Elbow

Nozzle

Gasket

Retaining Nut

Elbow

Fan Nozzle Tip

Avoid using a sprayer for general cleaning purposes if plant protection or herbicide chemicals have

already been used in the sprayer. If a sprayer has been used for plant protection or as an herbicide, clean

the sprayer completely (see cleaning section) before using.

Plant Food: Use different spray patterns for optimum foliage feeding or for fungicide and pesticide

application.

Herbicides: Reduce weeds and unwanted plants but avoid using the same sprayer for plant feeding or

protection without thoroughly cleaning (see cleaning section) the sprayer ﬁrst.

General Household Use: Apply detergents, cleaning solutions, warm water (do not exceed

120°F/49°C) or nontoxic household cleaning chemicals for carpets, ﬂoors, walls, glass, counter tops and

ceilings. DO NOT use sprayer that has been used with herbicides, pesticides or other toxic chemicals for

household applications.

General Outdoor Use: Use the sprayer for cleaning windows or with a detergent for general purpose

cleaning.

SPRAYER COMPONENTS & USE INFORMATION

NOZZLE ASSEMBLY

Figure 1-2

Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the

elbow (5). Unscrew the retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of

the retaining nut (2). To reinstall the nozzle, reverse the above instructions.

Figure 3

Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining

nut. To reinstall the nozzle, reverse the above instructions.

APPLICATIONS & USE FOR YOUR SPRAYER

SPRAYER COMPONENTS & USE INFORMATION, Continued

O-ring

Wand

Retaining Nut

Shut-off

Valve

WAND ASSEMBLY

1. Make sure the o-ring is installed on the end of the wand. Insert the wand into shut-off valve.

2. Turn and tighten the retaining nut clock-wise onto the shut-off valve.

The top of the shoulder straps are attached to the tank.

Attach the lower end of the straps by clipping the strap hooks to the

metal frame between where the frame exits the tank and curves around.

INSTALLING THE SHOULDER STRAP

Figure 1

Stage 1

(Filter

basket)

3 STAGE FILTERING SYSTEM

Stage 2

(Removable

In-Tank Filter

Pressure

Cylinder

This backpack sprayer is equipped with a 3 stage ﬁltering system (see ﬁgure

1). Stage 1 is a ﬁlter basket incorporated into the tank opening where ﬂuid is

added. Stage 2 ﬁlter is located at the inlet of the pressure cylinder. Stage 2

is a removable In-Tank ﬁlter. Stage 3 is a removable ﬁlter incorporated into

the shut-off assembly. Periodic cleaning of these ﬁlters is recommended to

insure consistent ﬂuid ﬂow through the sprayer. This will also reduce sprayer

component wear.

The stage 3 ﬁlter is a removable ﬁlter incorporated into the inlet side of the

shut-off valve (see section “disassembling and repairing the shut-off valve”) .

Make sure pressure is released before detaching the hose from the shut-off.

It is best to have no or minimal ﬂuid in the pressure cylinder before removing

and reinstalling the stage 3 shut-off ﬁlter as ﬂuid can leak from the hose.

Stage 3

(removable

Shut-off ﬁlter)

Figure 2 Stage 2 (removable In-Tank ﬁlter)

Guide edge facing away from

pressure cylinder

Guide edge on pressure

cylinder

FILLING THE SPRAYER

Make sure the ﬁlter basket is in place to keep debris from entering the tank.

Determine the amount of mixture needed for your application. Add the proper amount of water to

the tank. Add the proper amount of chemical to the tank (check the chemical label for proper ratio of

chemical). Stir mixture in tank with a clean utensil (like a paint stirrer). The tank will hold the 4-gallon

(15.1L) capacity plus the chemical.

It is not necessary to completely ﬁll the sprayer tank with each use. You can ﬁll the tank with only the

amount needed for each application.

Always follow the manufacturer’s instructions included on their product label.

SPRAYER COMPONENTS & USE INFORMATION, Continued

CLEANING

• Always empty the sprayer and clean the tank thoroughly after each use.

Other Cleaning Hints:

• Improper spray distribution usually means the nozzle is clogged, remove the nozzle and clean it.

• Soap can be added to the water to clean the tank.

• Do not use strong cleaning agents or abrasives.

• If you use a chemical agent to clean the tank follow the manufacturer’s recommendations for the

disposal of the waste water.

• Follow the chemical manufacturers instructions for clean up.

OPERATING THE SPRAYER

• Plug in charged battery

• Turn switch to on position

• Spray liquid back into tank to prime pump

• Close shut-off. Pump should stop running.

• Replace cap & begin spraying.

STORING / MAINTAINING YOUR SPRAYER

The Battery Should be removed prior to storage.

• The sprayer should be stored out of direct sunlight in a cool dry space.

• Before freezing weather make sure to drain all liquid in the tank, pump, hose,

shut-off valve, wand and nozzle, to avoid liquid expansion and cracking in the sprayer components

(See “Cleaning” section). Lock the shut-off valve in the “open” position.

• When service is required call your nearest dealer and always insist on original manufactured

replacement parts.

• Inspect the hose, wand, tank and shut-off valve for wear, damage or leaks on a regular basis

and repair defects promptly.

POWDER-BASED CHEMICALS

Powder-based chemicals (powder mixed with liquids to make the spraying agent) are usually

abrasive and can cause wear. When you use a powder-based chemical in your sprayer, make sure it

is thoroughly dissolved in the liquid solution. Thoroughly clean and ﬂush the sprayer with water to

extend the life of the sprayers parts.

When ﬁnished spraying turn switch to off position.

Remove and re-charge battery.

Note: Unit is equipped with a battery protection circuit. If sprayer abruptly stops after spraying for an

extended period of time, the battery may require charging.

DISASSEMBLING AND REPAIRING THE SHUT OFF VALVE

1) Assembled shut-off valve (Figure 1).

2) Remove the retaining pin (A) (Figure 2) place the notched end

of the retaining pin on a hard surface and push down. Remove the

retaining pin and slide the handle off the valve.

3) Remove the retaining nut (o-ring attached), spring, and valve stem (B)

(Figure 3). Replace worn parts. Lubricate the O-rings and reassemble by

reversing the steps above. Place the handle groove in the slotted area of

the valve stem and make sure the locking clip is positioned in the neutral

position (see “Helpful Spraying Information” section). Insert the retaining

pin. Push down on the handle a few times to distribute the lubricant

evenly. Check ﬁlter (C) in end of shut-off valve for debris. Remove ﬁlter

and ﬂush with water to clean out.

Figure 3

Figure 1

Figure 2

Valve

Stem

Unit runs but does not spray Pump is not primed Activate shut-off handle until liquid

sprays out. Release handle and pump

will shut-off.

Unit will not start Battery pack not installed properly Check battery pack installation

Battery pack not charged Check battery pack charging requirements

Battery pack will not charge Battery pack not inserted into charger Insert battery pack into charger until

green LED appears

Charger not plugged in Plug charger into a working outlet.

Refer to “Important Charging Notes” for

more details

Surrounding air temperature too hot or too cold Move charger and battery pack to a

surrounding air temperature of

above 40 degrees F (4.5ºC) or below

105 degrees F (+40.5º)

Unit shuts off abruptly Battery pack has reached its maximum thermal limit. Allow battery pack to cool down.

Out of charge. (To maximize the life of the battery Place on charger and allow to charge.

pack it is designed to shutoff abruptly when the

charge is depleted.)

Shut-off leaks Connections loose Tighten connection

Worn or damaged shut-off Rebuild or replace the shut-off valve

Wand assembly leaks Connections loose Tighten connection

Damaged or worn o-ring/gasket Replace o-ring/gasket

Nozzle assembly leaks Connections loose Tighten connection

Damaged or worn o-ring/gasket Replace o-ring/gasket

Leak between pump assembly Pump clamp loose Tighten clamp

and tank O-ring worn or damaged Replace pressure chamber o-ring

Hose leaking at tank outlet Hose clamp loose Tighten clamp

Hose leaking at shut-off Connection loose Tighten retaining nut

Damaged or worn o-ring/gasket Replace o-ring/gasket

TROUBLE SHOOTING YOUR SPRAYER

Symptom Possible Reason Correction

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lithium-ion battery (or battery pack)

indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been

paid by Black & Decker. In some areas, it is illegal to place spent lithium-ion batteries in the trash or municipal

solid waste stream and the RBRC program provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has been established programs in

the United States and Canada to facilitate the collection of spent lithium-ion batteries. Help protect our

environment and conserve natural resources by returning the tool to an authorized Black & Decker service

center for recycling. You may also contact your local recycling center for information on where to drop off the

spent battery, or call 1-800-8-BATTERY.

6-8138

Shut-off

Assembly

11E

REPLACEMENT PARTS ORDER INFORMATION

6-8096

Flat Fan

Nozzle

6-8122

Brass

Adjustable

Nozzle

6-8093

Poly

Adjustable

Nozzle

Retaining

Nut

Nozzle

gasket

Elbow with

o-ring

6-8148

Nozzle Kit

6-8120B

Shut-off Valve

Repair Kit

6-8131

Nozzle Kit

6-8169

Filter

Replacement

Kit

6-8101

Wand

Assembly

Wand

O-ring

Screw

Cap

Congratulations!

You have just purchased a quality Chapin product.

Chapin International, Inc

P. O. Box 549 700 Ellicot St. • Batavia, NY 14021-0549 U.S.A. • 1-800-950-4458 • www.chapinmfg.com

Due to our ongoing product improvement process, product speciﬁcations may change without notice. U.S. and foreign patents pending.

REPLACEMENT PARTS ORDER INFORMATION

6-8153

O-ring Kit

Elbow O-ring

Hose Gasket

Nozzle Gasket Wand O-ring

6-8146-1

Filter Basket

& Cap

6-8137

Straps

6-8105

Hose

Assembly

Hose Washer

Retaining Nut

Hose

Modelo 63985 • 4G/ 15L

013723 R0115

Lea estas instrucciones atentamente antes de utilizarlo

Chapin International, Inc

P.O. Box 549

700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458

www.chapinmfg.com

NO DEVOLVER ESTE

PULVERIZADOR A LA TIENDA.

LLAMAR AL: 1-800-950-4458

www.chapinmfg.com

ADVERTENCIA

Manual de uso

y cuidado

Pulverizador

de mochila

Proseries

™

Pulverizador

de mochila

Proseries

™

Page is loading ...

Modèle 63985 • 4 G/ 15 L

013723 R0115

lisez attentivement ces instructions avant l’utilisation

Chapin International, Inc

P.O. Box 549

700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458

www.chapinmfg.com

NE PAS RETOURNER CE

PULVÉRISATEUR AU MAGASIN.

APPELER: 1-800-950-4458

www.chapinmfg.com

AVERTISSEMENT

Manuel d’utilisation

et d’entretien

Pulvérisateur

de sac à dos

Proseries

™

Pulvérisateur

de sac à dos

Proseries

™

Page is loading ...

Chapin 63980 User manual

Brand: Chapin

Model: 63980

Type: User manual

This manual is also suitable for

63985

Download PDF

report

in other languages

français: Chapin 63980 Manuel utilisateur
español: Chapin 63980 Manual de usuario

Chapin 63980 User manual

This manual is also suitable for

Chapin 63980 User manual

in other languages

Related papers

Other documents