AWID LR-2000KIT Quick Installation Manual

AWID
Brand
AWID
Model
LR-2000KIT
Type
Quick Installation Manual

AWID LR-2000KIT is a UHF Reader Test Kit designed for planning, installing, and testing LR-2000, LR-2200, and LR-3000 readers, as well as their tags and cards. It's an essential tool for building confidence in the performance of long-range readers and their tags.

With the LR-2000KIT, you can:

  • Demonstrate the LR-2000-EVAL reader to potential customers or test its capabilities before installation.

  • Test the planned location for reliable reader operation, ensuring optimal performance at the desired site.

  • Observe the performance of a regular LR-2000/3000-family reader, whether in bench-testing or installed at the site.

AWID LR-2000KIT is a UHF Reader Test Kit designed for planning, installing, and testing LR-2000, LR-2200, and LR-3000 readers, as well as their tags and cards. It's an essential tool for building confidence in the performance of long-range readers and their tags.

With the LR-2000KIT, you can:

  • Demonstrate the LR-2000-EVAL reader to potential customers or test its capabilities before installation.

  • Test the planned location for reliable reader operation, ensuring optimal performance at the desired site.

  • Observe the performance of a regular LR-2000/3000-family reader, whether in bench-testing or installed at the site.

LR-2000KIT Quick Installation Guide
18300 Sutter Blvd., Morgan Hill, CA 95037
Quick Installation Guide
If you are new to the LR-2000, LR-
2200 or LR
we suggest that you call AWID Technical Support at 408
The LR-
2000KIT UHF Reader Test Kit is for planning, installing and testing the LR
readers, and their tags and cards. Keep the complete Kit, with this Guide, for quick access in your truck or shop.
It is your prime tool to build confidence in performance of the LR
Uses for the LR-2000KIT UHF Read
er Test Kit
• Demonstrate the LR-2000-EVAL
•
Test the planned location, to assure
• Observe performance of a regular
LR
•
Select the ideal location for mounting the vehicle tags, or holding the card
•
Prove that the vehicle tags operate well after they are mounted in
• Substitute for the installed LR-
2000/3000
Inside the Kit’s Case
• “EVAL” Reader –
This is the 8 inch by 8 inch reader. It is a permanent part of this Kit. It has no data output.
It can not interface to your system. It is for demo and test only. The “EVAL” reader contains
• LR-Sounder Test Unit –
This unit (about 3 inches by 4
reader. It beeps and changes LED color when the tag is read. It is perfect for demoing and testing an installation.
• USB-to-DB9 Adapter – It
extends the serial adapte
• DB9-to-Clips Adapter –
It connects a reader to a PC or controller
• DC Power Unit –
It provides 12 volts DC to test an LR
• Credentials – 10 UHF tags and
cards
HT-UHF Hangtag, VT-UHF Sunv
isor Tag, WS
Metal-Mount Tag, RV-
UHF Rearview Mirror Tag
• Instructions – This
Quick Installation Guide, laminated for long life.
Recommended Accessories
Camera tripod, for temporary
Version 1.10
Applied Wireless Identifications Group, Inc.
18300 Sutter Blvd., Morgan Hill, CA 95037
• Voice 1-408-825-1100 • Fax 1
-
Quick Installation Guide
– LR-
2000KIT UHF Reader Test Kit
2200 or LR
-
3000 reader, or if this is your first long
we suggest that you call AWID Technical Support at 408
-825-
1100.
2000KIT UHF Reader Test Kit is for planning, installing and testing the LR
-
2000, LR
readers, and their tags and cards. Keep the complete Kit, with this Guide, for quick access in your truck or shop.
It is your prime tool to build confidence in performance of the LR
-2000/3000-
family reader and its tags.
er Test Kit
reader (special
unit
included in the Kit) to your sales prospects and customers.
Test the planned location, to assure
reliable operation of the long-
range reader at the site.
LR
-2000/3000-family reader, either in bench-
testing or installed at the site.
Select the ideal location for mounting the vehicle tags, or holding the card
s
, inside or outside the vehicle
Prove that the vehicle tags operate well after they are mounted in
or on the vehicles.
2000/3000
-family reader in a service call.
This is the 8 inch by 8 inch reader. It is a permanent part of this Kit. It has no data output.
It can not interface to your system. It is for demo and test only. The “EVAL” reader contains
This unit (about 3 inches by 4
-
1/2 inches) alerts you to every read of the tag by the
reader. It beeps and changes LED color when the tag is read. It is perfect for demoing and testing an installation.
extends the serial adapte
r below to a USB port on your PC or controller.
It connects a reader to a PC or controller
that has a 9-
pin “D” serial port.
It provides 12 volts DC to test an LR
-2000/3000-
family reader, or to demo the “EVAL” reader.
cards
: GR-UHF Graphics Card, CS-
UHF Clamshell Card,
isor Tag, WS
-UHF Windshield Tag (
on a piece of windshield glass
UHF Rearview Mirror Tag
, SV-UHF Sideview Mirror Tag
, and PT
Quick Installation Guide, laminated for long life.
Camera tripod, for temporary
reader support at 6 feet height (supplied by the user).
Page 1 of 2
Applied Wireless Identifications Group, Inc.
-
408-782-7402 • www.awid.com
2000KIT UHF Reader Test Kit
3000 reader, or if this is your first long
-range installation,
1100.
2000, LR
-2200 and LR-3000
readers, and their tags and cards. Keep the complete Kit, with this Guide, for quick access in your truck or shop.
family reader and its tags.
included in the Kit) to your sales prospects and customers.
range reader at the site.
testing or installed at the site.
, inside or outside the vehicle
s.
This is the 8 inch by 8 inch reader. It is a permanent part of this Kit. It has no data output.
It can not interface to your system. It is for demo and test only. The “EVAL” reader contains
no LED or beeper.
1/2 inches) alerts you to every read of the tag by the
reader. It beeps and changes LED color when the tag is read. It is perfect for demoing and testing an installation.
r below to a USB port on your PC or controller.
(Black jacket.)
pin “D” serial port.
(Gray jacket.)
family reader, or to demo the “EVAL” reader.
UHF Clamshell Card,
KT-UHF Keytag,
on a piece of windshield glass
), MT-UHF
, and PT
-UHF Portable Tag..
reader support at 6 feet height (supplied by the user).
LR-2000KIT Quick Installation Guide Version 1.10 Page 2 of 2
Connections for Testing with the “EVAL” Reader
Use only the components from this LR-2000KIT UHF Reader Test Kit, including the “EVAL” Reader.
1. Clip together the LR-Sounder’s black lead, the power module’s black clip, and the reader’s black and yellow wires.
2. Clip the LR-Sounder’s orange lead to the “EVAL” reader’s orange wire.
3. Clip together the LR-Sounder’s red lead, the power module’s red clip, and the “EVAL” reader’s red wire.
4. Plug the power module into a 120 volts AC receptacle.
Connections to Test a Standard LR-2000/3000-Family Reader or a uAxcess Near-Field UHF Reader
Use an LR-2000/3000-family reader that is installed and interfaced to the host system, or being tested before installation.
1. Clip together the LR-Sounder’s black lead, the power module’s black clip, and the reader’s black and yellow wires.
2. Clip the LR-Sounder’s orange lead to the LR-2000/3000-family reader’s orange wire.
3. Clip together the LR-Sounder’s red lead, the power module’s red clip, and the LR-2000/3000 reader’s red wire.
4. Plug the power module into a 120 volts AC receptacle.
Connections to Interface a Reader with RS-232 Data Output into a PC
Use an AWID UHF reader, either long-range (LR) or near-field (uAxcess).
1. Clip the three spring clips of the gray RS-232 Cable Adapter to the same colors of the reader’s RS-232 data lines.
For uAxcess readers, connect the adapter’s orange wire to the reader’s violet wire.
2. Plug the 9-pin “D” connector on the adapter into the serial port of the PC or controller
If the PC has only USB ports, use the black USB Cable Adapter to extend the RS-232 adapter.
3. In the PC, run the AWIDACReaderSettings downloaded program. Print out the Instructions, which are zipped with it.
4. Observe the reader’s RS-232 data output as a row of 18 hexadecimal characters for each read of a tag or card.
Measuring Performance
Test for these standard performance parameters.
(Note: Avoid holding the reader by hand. You will measure best read range when the reader and tags are away from your hands and body.)
• Hang the reader in a large open space, 8 feet from the floor and side walls, clear in front for 30 feet or more.
• Starting close to the “EVAL” reader, move the test tag back along an imaginary line from the front of the reader.
Search for the farthest point at which a read is indicated by the LR-Sounder – often 25 feet or more for
the tags and cards. This determines the maximum range of the reader.
• Holding the tag at half of the maximum range, move the tag up and down, and side to side, to determine the
height and width of the effective RF field. This may be a circle with cross-section diameter up to 16 feet.
• Hold the test tag at 15 to 20 feet in front of the reader. Move the tag around to measure the cross-section of the
effective RF field. This is the “sweet spot” at which most vehicle tags will be read after the reader is installed.
• Attach the vehicle tag temporarily inside the vehicle at the proposed location. Support the “EVAL” reader outside
the vehicle, facing the tag, parallel to the tag. Move the reader away from the tag to find the maximum reading
distance. (When holding the reader for portable testing, keep your fingers away from the edges of the reader.)
Suggestions
LR-Sounder: The tester is not necessary with the LR-3000 reader. This reader has built-in LEDs that show DC power and tag reads.
Tags: Use only one UHF tag or card in the reader’s Effective RF Field. Move other tags and cards 30 feet behind the reader.
More Information
Visit AWID’s web site (www.awid.com) for product data and downloads. For Technical Support questions,
contact www.awid.com/support, or call in the U.S. +1-408-825-1100 from 5:00 a.m. to 5:00 p.m. Pacific Time.
  • Page 1 1
  • Page 2 2

AWID LR-2000KIT Quick Installation Manual

AWID
Brand
AWID
Model
LR-2000KIT
Type
Quick Installation Manual

AWID LR-2000KIT is a UHF Reader Test Kit designed for planning, installing, and testing LR-2000, LR-2200, and LR-3000 readers, as well as their tags and cards. It's an essential tool for building confidence in the performance of long-range readers and their tags.

With the LR-2000KIT, you can:

  • Demonstrate the LR-2000-EVAL reader to potential customers or test its capabilities before installation.

  • Test the planned location for reliable reader operation, ensuring optimal performance at the desired site.

  • Observe the performance of a regular LR-2000/3000-family reader, whether in bench-testing or installed at the site.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents