TEAC PD-H600 Owner's manual

Brand: TEAC

Model: PD-H600

Category: CD players

Type: Owner's manual

ENGLISH

PD-H600

Compact Disc Player

OWNER’S MANUAL

MANUEL DU PROPRIÉAIRE

MANUAL DEL USUARIO

FRANÇAIS ESPAÑOL

D01022020A

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider

than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong

are provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of the

obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning

storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally,

or has been dropped.

< Do not expose this apparatus to drips or splashes.

< Do not place any objects filled with liquids, such as vases, on the

apparatus.

< Do not install this apparatus in a confined space such as a book

case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

< The apparatus should be located close enough to the AC outlet

so that you can easily grasp the power cord plug at any time.

< The main plug is used as the disconnect device, the disconnect

device shall remain readily operable.

< An apparatus with Class

! construction shall be connected to an

AC outlet with a protective grounding connection.

< Batteries (battery pack or batteries installed) shall not be exposed

to excessive heat such as sunshine, fire or the like.

< Excessive sound pressure from earphones and headphones can

cause hearing loss.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

 For U.S.A.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE WITHIN!

< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

< USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

For U.S.A.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

M Reorient or relocate the equipment and/or the receiving

antenna.

M Increase the separation between the equipment and receiver.

M Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

M Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class 1 laser product. There is not hazardous invisible laser

radiation during operation because invisible laser radiation emitted

inside of this product is completely confined in the protective

housings.

The label required in this regulation is shown .

Optical pickup :

Type : SF-P101VZ

Manufacturer : Sanyo Electric Co., Ltd

Laser output : Less than 1mW on the objective lens

Wavelength : 790±30nm

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS

and Thomson.

This product is protected by certain intellectual property rights of

Microsoft.

Use or distribution of such technology outside of this product is

prohibited without a license from Microsoft.

Thank you for choosing TEAC. Read this manual carefully to

get the best performance from this unit.

Before Use ....................................................5

Discs .........................................................6

MP3 and WMA ................................................7

Remote Control Unit ..........................................7

Connection ...................................................8

Parts Identification ...........................................10

Basic Playback ...............................................12

Direct Track/File Selection ....................................14

Folder/File Search ............................................14

Repeat Playback .............................................15

Shuffle Playback .............................................15

Programmed Playback (Audio CD only) .......................16

Dimmer .....................................................17

Display ......................................................18

Troubleshooting .............................................19

Specifications ................................................19

Contents

Information for Users on Collection and Disposal of Old

Equipment and used Batteries

These symbols on the products, packaging, and/or

accompanying documents mean that used electrical and

electronic products and batteries should not be mixed with

general household waste. For proper treatment, recovery

and recycling of old products and used batteries, please

take them to applicable collection points, in accordance

with your national legislation and the Directives 2002/96/EC

and 2006/66/EC.

By disposing of these products and batteries correctly,

you will help to save valuable resources and prevent

any potential negative effects on human health and the

environment which could otherwise arise from inappropriate

waste handling.

For more information about collection and recycling

of old products and batteries, please contact your local

municipality, your waste disposal service or the point of sale

where you purchased the items.

Information on Disposal in other Countries outside the

European Union

These symbols are only valid in the European Union. If

you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of

disposal.

Note for the battery symbol (bottom right two symbol

examples):

This symbol might be used in combination with a chemical

symbol. In this case it complies with the requirement set by

the Directive for the chemical involved.

ENGLISH

Read this before attempting any operations.

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also

avoid locations subject to vibrations and excessive dust, heat,

cold or moisture.

< Do not place the unit on an amplifier/receiver.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into the

unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank the cord.

< To keep the laser pickup clean, do not touch it, and always close

the disc tray.

< Do not attempt to clean the unit with chemical solvents as this

might damage the finish. Use a clean, dry cloth.

< Keep this manual in a safe place for future reference.

During playback

During playback, the disc rotates at high speed. Do not lift or

move the unit during playback. Doing so may damage the disc

or the unit.

When moving this unit

When moving or packing the unit, be sure to remove the disc

and close the disc tray. Then, turn off the power and disconnect

the power cord. Moving this unit with the disc loaded may result

in damage to this unit.

Before Use

Beware of condensation

When the unit (or a disc) is moved from a cold place to a warm

place, or used after a sudden temperature change, there is a

danger of condensation: vapor in the air could condense on the

internal mechanism, making correct operation impossible. To

prevent this, or if this occurs, leave the unit for one or two hours

with the power turned on. Then the unit will stabilize at the

temperature of its surroundings.

Maintenance

If the surface of the unit gets dirty, wipe with a soft cloth or

use diluted neutral cleaning liquid. Be sure to remove any fluid

completely. Do not use thinner, benzine or alcohol as they may

damage the surface of the unit.

< Printable CD-R and CD-RW discs are not recommended, as the

label side might be sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do not

use any protective coating spray.

< Use a soft oil-based felt-tipped pen to write the information on

the label side. Never use a ball-point or hard-tipped pen, as this

may cause damage to the recorded side.

< Never use a stabilizer. Using commercially available CD stabilizers

with this unit will damage the mechanisms and cause them to

malfunction.

< Do not play irregular shape CDs (octagonal, heart shaped,

business card size, etc.). They can damage the unit.

< If you are in any doubt as to the care and handling of a CD-R/

CD-RW disc, read the precautions supplied with the disc, or

contact the disc manufacturer directly.

Discs

This unit can play the following discs:

< Conventional audio CDs bearing the COMPACT DISC DIGITAL

AUDIO logo on the label:

< Properly finalized CD-R and CD-RW discs

< MP3/WMA CDs

Note

< Depending on the quality of the disc and/or the condition of the

recording, some CD-R/CD-RW discs may not be playable.

< Copy-protected discs and other discs which do not conform to

the CD standard may not play back correctly in this unit. If you

use such discs in this unit, TEAC Corporation and its subsidiaries

cannot be responsible for any consequences or guarantee the

quality of reproduction. If you have problems with such non-

standard discs, you should contact the producers of the disc.

< Always place the disc on the disc tray with the label side up.

< To remove a disc from its storage case, press down on the center

of the case and lift the disc out, holding it carefully by the edges.

< Should the disc become dirty, wipe the surface radially (from the

center hole outward towards the outer edge) with a soft and dry

cloth.

< Never use such chemicals as record sprays, antistatic sprays or

fluid, benzine or thinner to clean the discs. Such chemicals will do

irreparable damage to the disc’s plastic surface.

< Discs should be returned to their cases after use to avoid dust

and scratches that could cause the laser pickup to ”skip”.

< Do not expose discs to direct sunlight or high humidity and

temperature for extended periods. Long exposure to high

temperatures will warp the disc.

< Do not play any disc that is warped, deformed or damaged.

Playing such discs may cause irreparable harm to the playing

mechanisms.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they

are not stored in a location where direct sunlight will fall on

them, and which is away from sources of heat such as radiators or

heat-generating electrical devices.

ENGLISH

This unit can play MP3 and WMA files recorded on a CD-R or CD-RW

disc.

< File names of MP3 or WMA should be alphanumeric characters.

This unit cannot display symbols and full-size or double-byte

characters (such as Japanese, Chinese, etc.) correctly. Also, be

sure to use the file extension. (”.mp3” for MP3 files, ”.wma” for

WMA files.)

< MP3 files are mono or stereo MPEG-1 Audio Layer 3 format. This

unit can play MP3 files with a sampling frequency of 44.1 kHz or

48 kHz and a bit-rate of 320 kbps or less.

< This unit can play WMA files with a sampling frequency of 44.1

kHz and a bit-rate of 192 kbps or less.

< Audio encoded at 128 Kbps should sound close to regular audio

CD quality. Although this unit plays lower bit-rate MP3 tracks, the

sound quality deteriorates noticeably at lower bit-rates.

< The disc must be finalized in order to play.

< The CD-ROM must be ISO 9660 compatible.

< When more than 255 files are recorded on a disc, the unit might

not play it correctly.

Remote Control Unit

You can operate the unit using the supplied remote control unit

RC-1182.

When operating the remote control unit, point it towards the

remote sensor on the front panel of the unit.

< Remote control operation may be impossible if there are any

obstacles between the unit and the remote control.

< If the remote control unit is operated near other appliances which

generate infrared rays, or if other remote control devices using

infrared rays are used near the unit, it may operate incorrectly.

Conversely, the other appliances may operate incorrectly.

Battery Installation

1. Remove the battery compartment cover.

2. Insert two ”AAA” (R03, UM-4) dry batteries. Make sure that the

batteries are inserted with their positive ”+” and negative ”_”

poles positioned correctly.

3. Close the cover.

Battery Replacement

If the effective range decreases, the batteries are exhausted. In

this case replace the batteries with new ones.

Precautions concerning batteries

< Be sure to insert the batteries with correct positive ”+” and

negative ”_” polarities.

< Use batteries of the same type. Never use different types of

batteries together.

< Rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

< When the remote control unit is not to be used for a long time

(more than a month), remove the batteries from the battery

compartment to prevent them from leaking. If they leak, wipe

away the liquid inside the battery compartment and replace the

batteries with new ones.

< Do not heat or disassemble batteries and never dispose of old

batteries by throwing them in a fire.

MP3 and WMA

Connection

CAUTION

< Switch off the power to all equipment before connecting any

components.

< Read the instructions of each component you intend to use with

this unit.

(LINE IN)SYSTEM CONTROL

DIGITAL IN

(COAXIAL)

AG-H600 series receiver

PD-H600

CD recorder etc.

ENGLISH

LINE OUT jacks

These jacks transmit an analog 2-channel audio signal. Connect

them to the CD jacks of a receiver or an amplifier with the

provided RCA cables.

< Make sure to connect the cables as follows:

White plug q White jack (L: left channel)

Red plug q Red jack (R: right channel)

< Be sure to insert each plug securely. To prevent hum and noise,

avoid bundling the signal interconnection cables together with

the AC power cord or speaker cables.

DIGITAL OUT jack

Connect it to a digital coaxial input terminal of a digital

apparatus such as a CD recorder with a commercially-available

digital coaxial cable.

< Make sure that the cable is firmly inserted.

SYSTEM CONTROL jack

If you have TEAC AG-H600 series receiver, convenient system

control functions are available.

Connect it to the SYSTEM CONTROL jack on the AG-H600 series

receiver with the provided system control connection cord.

Then set the SYSTEM CONTROL SELECTOR switch on this unit to

“SYSTEM”. (See

Available system control functions are as follows:

N When you turn on or standby the AG-H600 series receiver

using the remote control unit (RC-1181) of the receiver, this

unit is also turned on or standby synchronously.

N When you change the source from CD to another on

AG-H600 series receiver, playback stops and display turns off

on this unit.

Refer also to the manual of the AG-H600 series receiver.

SYSTEM CONTROL SELECTOR switch

When you want to use the system control functions, connect

the SYSTEM CONTROL jacks (see

), and set the switch to

“SYSTEM”.

< The STANDBY/ON button on the remote control unit of this unit

does not work while the switch is set to “SYSTEM”.

< When you do not use the system control functions or do not

have a AG-H600 series receiver, set the switch to “SINGLE“.

Otherwise, you cannot turn on or standby the unit.

SIGNAL GND terminal

Connect the signal ground of other components using a

commercially available jacketed cable (PVC-covered cable or

others).

< Note that this is NOT an electrical safety ground (earth).

AC Inlet

Use only the supplied power cord.

< Use of other power cord may result in fire or electric shock.

< Unplug the power cord when you are not going to use the unit

for an extended period of time.

White (L)

Red (R)

White (L)

Red (R)

Parts Identification

H GI F E

B C D

POWER

Press this switch to turn the unit on or off.

The standby indicator lights orange when the unit is in the standby mode.

When the unit is turned on, the indicator lights blue.

< If you use the system control function, leave the power switch being on.

Disc tray

Skip (.//)

Use these buttons to skip tracks/files. (See page 13.)

Open/Close (L)

Use this button to open or close the disc tray.

Play/Pause (G/J)

Use this button to start or pause playback.

Stop (H)

Use this button to stop playback.

REPEAT

Use this button to select a repeat playback. (See page 15.)

Display

Remote Sensor

When operating the remote control unit, point it towards the remote sensor.

ENGLISH

STANDBY/ON

Use this button to turn on or standby the unit.

< While the system control functions are activated, this button does

not work. To turn on or standby this unit, use the remote control

unit (RC-1181) of the AG-H600 series receiver.

TIME

Use this button to change the time information on the display.

(See page 18.)

DISPLAY

Use this button to change the information on the display. (See

page 18.)

PROGRAM

Use this button to enter the program mode. (See page 16.)

Numeric buttons

Use these buttons to select a track/file number. (See page 14.)

FOLDER (°/‡)

Use these buttons to select a folder of MP3/WMA. (See page 14.)

DIMMER

Use this button to dim the display. (See page 17.)

CLEAR

Use this button to clear a programmed track. (See page 16.)

Search (m/,)

During playback, use these buttons to search the part you want

to listen to. (See page 13.)

FILE (°/‡)

Use these buttons to select a file of MP3/WMA. (See page 14.)

SHUFFLE

Use this button to enter the shuffle playback mode. (See page

15.)

ENTER

Use this button to confirm the selection of a folder/file. (See page

14.)

< You can also use the following buttons on the remote control

unit (RC-1181) of the AG-H600 series receiver:

REPEAT,

Stop (H),

SHUFFLE,

Skip (.//),

Play/Pause (G/J),

Search (m/,)

Refer to the manual of the AG-H600 series receiver.

Audio CD:

MP3/WMA disc:

< When you press the play/pause button (G/J) (or the numeric

buttons of the remote control unit) before closing the disc tray,

the disc tray closes and playback starts.

< Keep fingers clear of moving tray to avoid trapping them.

Press the play/pause button (G/J) to start playback.

Playback starts from the first track/file.

Audio CD:

MP3/WMA disc:

< When the play time of a file is more than 100 minutes, the

elapsed time is displayed in hours and minutes and the colon

flashes.

< When the play time of a file is more than 4 hours (240 minutes),

“OVER” appears instead of the elapsed time.

Press the POWER switch to turn the unit on.

The standby indicator lights blue.

< When the system control functions are activated, always set this

switch on, and turn the unit on or standby using the remote

control unit (RC-1181) of the AG-H600 series receiver.

Press the open/close button (L) to open the disc tray.

Place a disc on the disc tray with the printed label faced up.

< The disc tray closes automatically after a minute.

< Place a disc in the center of the disc tray. If the disc is not

correctly placed, the disc tray may not open again after it closes.

Press the open/close button (L) to close the disc tray.

Standby indicator

Stop

T15 43:08

Stop

Total Files 144

5A B

4 CED

Song title, artist name and album name (scrolled)

Current track

number

Elapsed time of the

current track

MP3/

00:42

xxxxx xxx xxxxxx

CD/

T01 00:42

Elapsed time of the current file

(minutes and seconds)

Total number

of the tracks

Total play time of

the disc

Total number of files of the disc

Basic Playback

ENGLISH

Note

< It takes a few seconds to load a disc. No buttons work during

loading. Wait until the total number of the tracks and/or the total

play time of the disc are displayed.

< Playback stops automatically after all the tracks/files are played.

< “No Disc“ appears on the display when no disc is loaded in the

unit.

< MP3/WMA files recorded out of folders are recognized as the

contents of “ROOT“ folder. Playback starts from the first file of the

“ROOT” folder.

< If there are folders that has no MP3/WMA file, this unit skips them.

To stop playback

Press the stop button (H).

< To start playback again, press the play/pause button (G/J).

Playback starts from the first track/file.

To pause playback

Press the play/pause button (G/J).

“J” appears on the display.

< To resume playback, press the play/pause button (G/J) again.

To open or close the disc tray

Press the open/close button (L).

< When you press the open/close button (L) during playback,

playback stops and the disc tray opens.

< After ejecting the disc, press the open/close button (L) again to

close the disc tray.

To skip to the next or a previous track/file

Press the skip buttons (.//).

The selected track/file is played from the beginning.

< When playback is stopped or paused, press the skip buttons

(.//) repeatedly until the track/file you want to listen to is

found. Then press the play/pause button (G/J).

< When the skip button (.) is pressed during playback, the

current track is played from the beginning. To return to the

beginning of the previous track, press the skip button (.)

twice.

< During programmed playback, playback skips to the next or

previous track in the program.

To search for a part of a track/file

During playback, hold down the skip buttons (.//) until

the part you want to listen to is found.

< On the remote control unit, hold down the search buttons

(m/,).

< Playback stops when the searching reaches the end of the last

track/file.

While playing or playback is stopped, you can select and play a

desired folder or a desired file in an MP3/WMA folder.

Select a folder.

Press the FOLDER buttons (°/‡).

< When the disc has no folder or only one folder, go to

< The order of the folders may changed depending on the

hierarchy of the folders.

Confirm the selection.

Press the ENTER button.

Playback starts from the beginning of the selected folder.

Select a file if you want.

Press the FILE buttons (°/‡).

Confirm the selection.

Press the ENTER button.

Playback starts from the selected file.

You can use the numeric buttons of the remote control to select a

track/file.

Press the numeric buttons to select a track/file.

Examples:

Track/file 3:

Track/file 15:

File 107:

< If a numeric button is pressed and leave the unit more than 5

seconds, the selection will be entered.

Playback starts from the selected track/file.

Direct Track/File Selection Folder/File Search

Numeric buttons

ENGLISH

Each time you press the REPEAT button, repeat playback changes

as follows:

RP 1 (Repeat one track)

RP F (Repeat folder)*

RP A (Repeat all)

(Repeat off)

* MP3/WMA discs only

< When you stop playback, repeat playback is cancelled.

RP 1 (Repeat one track):

The track/file being played is played repeatedly. When you

select another track/file, the track/file you selected will be played

repeatedly.

If you select “RP 1” while playback is stopped and select a track/

file, the selected track/file will be played repeatedly.

RP F (Repeat Folder) (MP3/WMA discs only):

All the files in the folder will be played repeatedly. When you

select another folder, the files in the folder you selected will be

played repeatedly.

If you select “RP F” while playback is stopped and select a folder,

the files in the selected folder will be played repeatedly.

RP A (Repeat All):

All the tracks/files are played repeatedly.

< During programmed playback, the programmed contents are

played repeatedly.

Repeat Playback

When the SHUFFLE button is pressed, the tracks/files of the disc

are played randomly.

< To cancel shuffle playback, press the SHUFFLE button again.

< When you stop playback, shuffle playback is cancelled. The unit

repeats shuffle playback until you press the stop button (H).

< If you press the skip button (/) during shuffle playback,

next track is randomly selected and played. If you press the skip

button (.), the current track/file is played from the beginning.

You cannot go back to the previous track/file.

< The numeric buttons, FOLDER buttons (°/‡) and FILE buttons

(°/‡) do not work during shuffle playback.

Shuffle Playback

CD/

SFL

T05 00:13

Note

< When you stop programmed playback, the total number of the

programmed tracks and total time are shown on the display.

< When you press the SHUFFLE button during programmed

playback or you press the SHUFFLE button then press the play/

pause button (G/J) while programmed playback is stopped,

shuffle playback starts, but program mode will not be cancelled.

You can return to the programmed playback by stopping shuffle

playback and pressing the play/pause button (G/J).

To stop programmed playback

Press the stop button (H).

< When the stop button (H) is pressed, playback stops, but program

mode will not be cancelled. You can return to programmed

playback by pressing the play/pause button (G/J).

To check the programmed order

Press the PROGRAM button repeatedly while playback is stopped.

The track number and program number are shown on the

display. “P-end” appears at the end of the program.

< To return to the normal display of programmed playback, start

and stop programmed playback.

You can play up to 30 tracks in a desired order.

< Insert a disc before programming.

Enter the program mode.

Press the PROGRAM button.

< You cannot program during playback.

Select a track using the numeric buttons.

Example: to select track/file 15

Repeat the selection until you finish programming desired tracks.

< If you attempt to program more than 30 tracks, ”P-full” (Program

is full) appears and no more tracks can be programmed.

< To correct a selection, press the CLEAR button. The last

programmed track is cleared.

< If you press the stop button (H), all the programmed tracks are

cleared.

Start programmed playback.

Press the play/pause button (G/J).

< “PRG” is displayed during programmed playback and while it is

stopped.

< Playback stops automatically after all programmed tracks are

played.

Selected track number

Stop PROGRAM

P-00 T00

Stop PROGRAM

P-01 T15

CLEAR

Program number

Programmed Playback (Audio CD only)

ENGLISH

To delete a track from the program

While playback is stopped, press the PROGRAM button repeatedly

until the track number to be deleted appears on the display, then

press the CLEAR button.

The selected track is deleted from the program and the next track

is displayed.

< If you hold down the CLEAR button for more than 3 seconds, all

the tracks will be cleared.

To add a track to the program

While playback is stopped, press the PROGRAM button repeatedly

until the program number that you want to insert a track appears

on the display. Then select a track using the numeric buttons.

< When you want to add a track to the end of the program, press

the PROGRAM button repeatedly until “P-end” appears on the

display. Then select a track using the numeric buttons.

To clear the program

While playback is stopped, press the PROGRAM button, then

press the stop button (H).

< When you press one of the following buttons, the program is also

cleared:

open/close (L),

STANDBY/ON on the remote control unit,

POWER

Each time you press the DIMMER button, the display changes as

follows:

NORMAL (Normal)

DIMMER (Dimmed)

LIGHT OFF (Display off)

Note

< This setting is not memorized when the unit turns standby/on.

The next time the unit is turned on, the display is illuminated as

normal.

< When the unit is operated during the setting is “LIGHT OFF“, the

display turns normal briefly and will turn off again.

< The display is turned off about 5 seconds after the last operation

regardless of the dimmer setting, if Tone Direct is active on the

AG-H600 series receiver linked with this unit through the system

control function.

Dimmer

Changing the information

You can change the information on the display.

Each time you press the DISPLAY button, the information changes

as follows.

Audio CD:

< Music calender shows the track number up to 15. When the disc

contains more than 15 tracks, “G” appears next to “15”.

< While a track is played, its track number of the music calendar

flashes. After playback of the track finishes, the track number

disappears.

MP3/WMA disc (During playback):

Song title, artist name and album name (scrolling)

Folder number and file number

File name

Song title

Artist name

Album name

CD/

00:42

123456789

101112131415

CD/

T01 00:42

Display

Music calendar

Changing the time information (Audio CD

only)

You can change the time information for audio CD playback.

Each time you press the TIME button during playback, the time

information changes as follows:

Current track number and elapsed time of the current track

Current track number and remaining time of the current track

Current track number and the total elapsed time of the disc

Current track number and the total remaining time of the disc

< While the music calendar is shown on the display, the time

information is shown at the upper right.

< The TIME button does not work during playback of an MP3/WMA

disc.

CD/

T08 43:08 TOTAL

CD/

T08 00:42

CD/

T08 -42:26 TOTAL

CD/

T08 -03:02

ENGLISH

Troubleshooting

If you have any problems with the unit, please take a moment

to look through this chart and see if you can solve the problem

yourself before you call your dealer or a TEAC service center.

No power.

e Check the connection to the AC power source. Check and

make sure the AC source is not a switched outlet and if it is, the

switch is turned on. Make sure there is power to the AC outlet

by plugging another item such as a lamp or fan.

e While the system control function is activated, turn on the unit

using the remote control unit (RC-1181) of the AG-H600 series

receiver.

e When you do not use the system control function, set the

SYSTEM CONTROL SELECTOR switch to “SINGLE“.

No sound.

e Check the connection to the amplifier/receiver.

e Check the operation of the amplifier/receiver.

Remote control doesn’t work.

e If the batteries are exhausted, change the batteries.

e Use remote control unit within the range (5m) and point at the

front panel.

e Make sure that there are no obstacles between the remote

control unit and the main unit.

e If a fluorescent light is near the unit, turn it off.

e While the system control function is activated, the STANDBY/

ON button on the remote control unit of this unit does not

work. Use the same button on the remote control unit (RC-

1181) of the AG-H600 series receiver.

Cannot play.

e Load a disc with the playback side facing down.

e A blank disc may be loaded. Load a prerecorded disc.

e Depending on the disc, etc. it may not be possible to play back

CD-R/CD-RW discs. Try again with another disc.

e You cannot play back unfinalized CD-R/CD-RW discs. Finalize

such a disc in a CD recorder and try again.

Sound skips.

e Place the unit on a stable place to avoid vibration and shock.

e If the disc is dirty, clean the surface of the disc.

e Do not use scratched, damaged or warped discs.

Cannot programmed play.

e If the unit turns off or the disc tray is opened, the programmed

contents are cleared.

No display.

e Set the dimmer setting to “NORMAL” or “DIMMER”.

e Change the source to CD on the AG-H600 series receiver.

e While Tone Direct is active on the AG-H600 series receiver, the

display is turned off.

If normal operation cannot be achieved, unplug the power

cord from the outlet and plug it again.

Specifications

Frequency Response .........................20 Hz - 20 kHz, ±0.5 dB

Total Harmonic Distortion (at 20 kHz LPF)

Less than 0.003 % (1 kHz)

Signal-to-Noise Ratio (S/N) (at 20 kHz LPF)

More than 110 dB (1 kHz, 0 dB, A weight)

Output ..........................Analog: 2.0 Vrms (RCA, 1 kHz, 0 dB)

Digital: RCA COAXIAL (0.5 V, 75 Ω)

Power Requirement .................................AC 230 V, 50 Hz

Power Consumption ...........................................9 W

Dimensions (W x H x D) ........................290 x 102 x 308 mm

Weight (Net) .................................................5.4 kg

Accessories

RCA cable x 1

System control connection cord x 1

Power cord x 1

Remote control unit (RC-1182) x1

Batteries (AAA) x2

Owner’s manual x1

Warranty card x1

< Design and specifications are subject to change without notice.

< Weight and dimensions are approximate.

< Illustrations may differ slightly from production models.

This appliance has a serial number located on the rear panel. Please record

the model number and serial number and retain them for your records.

Model number Serial number

TEAC CORPORATION

1-47 Ochiai, Tama-shi, Tokyo 206-8530, Japan Phone: (042) 356-9156

TEAC AMERICA, INC. 7733 Telegraph Road, Montebello, California 90640 Phone: (323) 726-0303

TEAC CANADA LTD. 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: (905) 890-8008

TEAC MEXICO, S.A. de C.V Rio Churubusco 364, Colonia Del Carmen, Delegación Coyoacàn, CP 04100, México DF, México Phone: (5255)5010-6000

TEAC UK LIMITED Unit 19 & 20, The Courtyards, Hatters Lane, Watford, Hertfordshire, WD18 8TE, U.K. Phone: (0845) 130-2511

TEAC EUROPE GmbH Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: 0611-71580

1108

MA-1431A

Page is loading ...

TEAC PD-H600 Owner's manual

Brand: TEAC

Model: PD-H600

Category: CD players

Type: Owner's manual

Download PDF

report

TEAC PD-H600 Owner's manual

TEAC PD-H600 Owner's manual

Related papers

Other documents