TEAC CD-RW890MK2-B User manual

Z

CD-RW890MK"

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

CD Recorder

77-20RW89000007

ENGLISH FRANÇAIS ESPAÑOL

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A

SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN

REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

Model for USA

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Declaration of Conformity

Responsible party:

TEAC AMERICA, INC.

Address: 1834 Gage Road, Montebello, California, U.S.A.

Telephone number : 1-323-726-0303

This device complies with Part.15 of FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including interference

that may cause undesired operation of the device.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

DECLARATION OF CONFORMITY

We, TEAC AUDIO EUROPE, Liegnitzer Straße 6, 82194

Gröbenzell, Germany declare in own responsibility,

the TEAC product described in this manual is in

compliance with the corresponding technical standards.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

IMPORTANT SAFETY PRECAUTIONS

2

Laser information

This product contains a semiconductor laser system inside the cabinet

and is classified as a “CLASS 1 LASER PRODUCT”.

To prevent being exposed to the laser beam, do not try to open the

enclosure.

Laser:

Type: LO-DWH02/LO-DWH02B

Manufacturer: Lite-space Technology Co., Ltd.

Laser output: Less than 131.9 mW (CD) and 147.8 mW (DVD)

on the objective lens

Wavelength: 785 nm (CD) typical

661 nm (DVD) typical

Model for USA

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

V Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to fire,

injury or the staining of nearby things. Please read and observe the

following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery com-

partment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

(a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

(b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on human

health and the environment.

(c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

(d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

(e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat regis-

ters, stoves, or other apparatus (including amplifiers) that produce

heat.

9) Do not defeat the safety purpose of the polarized or ground-

ing-type plug. A polarized plug has two blades with one wider

than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particu-

larly at plugs, convenience receptacles, and the point where they

exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The power plugs are used as disconnect devices; the disconnect

devices shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or equiv-

alent type.

Company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

4

5

ENGLISH

Before Using the UnitContents

Thank you for choosing TEAC. Read this manual carefully

to get the best performance from this unit.

IMPORTANT SAFETY PRECAUTIONS ...............................2

IMPORTANT SAFETY INSTRUCTIONS ..............................4

Before Using the Unit ............................................5

Using the TEAC Global Site .......................................5

Product registration .............................................. 5

Discs ............................................................6

Connections .....................................................7

Unit Functions and Remote Control ..............................8

Remote Control Unit .............................................9

Playback

Basic Operation .................................................10

Basics of Playback ...............................................10

Direct Playback .................................................12

Shuffle Playback ................................................12

Time Display ....................................................13

Repeat Playback ................................................13

A-B Repeat ...................................................... 14

Programmed Playback ..........................................14

Recording

About Recording ................................................16

Before Recording ...............................................17

Recording ......................................................17

Synchronous Recording .........................................20

Finalize .........................................................21

Unfinalize .......................................................21

Erasing the Last Track (CD-RW) ..................................22

Erasing All Tracks (CD-RW) .......................................23

Erasing All Tracks In Refresh Mode (CD-RW) ......................24

Troubleshooting ................................................25

Messages .......................................................26

Specifications ...................................................27

Read this before attempting any operations.

< The nominal temperature should be between 5°C and 35°C (41°F

and 95°F). The CD-RW recorder is more sensitive to extremes of

temperature than ordinary CD players.

< Relative humidity should be 30 to 85 percent non condensing.

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also avoid

locations subject to vibrations and excessive dust, heat, cold or

moisture.

< Do not place the unit on an amplifier/receiver.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into the

unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank the cord.

< To keep the laser pickup clean, do not touch it and always close

the disc tray.

< Do not attempt to clean the unit with chemical solvents as this

might damage the finish. Use a clean, dry cloth.

< Keep this manual in a safe place for future reference.

< Do not tilt the main unit while a disc is inserted. Doing so may

cause a malfunction.

DO NOT MOVE THE UNIT DURING PLAYBACK/RECORDING

During playback or recording, the disc rotates at high speed.

Do NOT lift or move the unit during playback or recording.

Doing so may damage the disc or the unit.

WHEN MOVING THIS UNIT

When changing the unit’s location or packing the unit for moving,

be sure to remove the disc. Moving this unit with the disc loaded

may result in damage to this unit.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to open

the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the “Search by Model Name” section to open the Downloads

page for that product. (Users in Europe should click the product

name in the “Products” section instead.)

4) Select and download the updates that are needed.

Product registration

Customers in the USA, please visit the following TEAC website to

register your TEAC product online.

http://audio.teac.com/support/registration/

6

Playable discs

The main unit can play the above discs without an adapter. Other

discs are not available.

If you attempt to play discs other than the above, a loud

noise may occur to damage the speakers or your hearing.

Do not play such discs.

< Copy-protected discs, DualDiscs and other discs which do not

conform to the CD standard may not play back correctly in this

player. If you use such discs in this unit, TEAC Corporation and

its subsidiaries cannot be responsible for any consequences or

guarantee the quality of reproduction. If you experience problems

with such non-standard discs, you should contact the producers of

the disc.

About CD-R and CD-RW discs

The main unit can play CD-R and CD-RW discs recorded in audio CD

format (CD-DA).

< Remember to finalize a disc recorded with the CD recorder.

< Depending on the quality of the disc and/or the condition of the

recording, some CD-R/CD-RW discs may not be playable.

< If you are in any doubt as to the care and handling of a CD-R/

CD-RW disc, read the precautions supplied with the disc, or

contact the disc manufacturer directly.

Recordable discs

Cautions for use

< Do not use cracked discs as doing so may cause a malfunction.

< Printable CD-R and CD-RW discs are not recommended, as the

label side might be sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do not

use any protective coating spray.

< Use a soft oil-based felt-tipped pen to write the information on the

label side. Never use a ball-point or hard-tipped pen, as this may

cause damage to the recorded side.

< Never use a stabilizer. Using commercially available CD stabilizers

with this unit will damage the mechanism and cause them to

malfunction.

< Do not use CDs with an irregular shape (octagonal, heart shaped,

business card size, etc.). CDs of this sort can damage the unit:

Handling disc

< Always place the disc on the disc tray with the label side

uppermost. (Compact discs can be played or recorded only on

one side.)

< Scratches, fingerprints, dirt, etc. on the signal recording surface

(without labels) may cause a playback error. Be careful when

handling.

< To remove a disc from its storage case, press down on the center

of the case and lift the disc out, holding it carefully by the edges.

How to remove the disc How to hold the disc

Storing disc

< Discs should be returned to their cases after use to avoid dust and

scratches that could cause the laser pickup to “skip”.

< Do not expose discs to direct sunlight or high humidity and

temperature for extended periods. Long exposure to high

temperatures will warp the disc.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they are

not stored in a location where direct sunlight will fall on them, and

away from sources of heat such as radiators or heat-generating

electrical devices.

< Dirt on the disc may cause the sound to skip or lower the sound

quality. Always keep it clean when storing.

Maintenance

< Should the disc become dirty, wipe the surface radially (from the

center hole outward towards the outer edge) with a soft, dry cloth.

< Never use such chemicals as record sprays, antistatic sprays or

fluid, benzine or thinner to clean the discs. Such chemicals will do

irreparable damage to the disc’s plastic surface.

Discs

Please use CD discs bearing the “COMPACT disc DIGITAL

AUDIO” logo.

CD-R and CD-RW discs properly recorded and finalized in

audio CD format.

CD-R and CD-RW discs bearing the "DIGITAL AUDIO" logo

7

ENGLISH

RL

CD-RW890MK

"

A B

C

Connections

CAUTION:

< Switch off the power to all equipment before making connections.

< Read the instructions of each component you intend to use with this unit.

< Be sure to insert each plug securely. To prevent hum and noise, avoid bundling

the signal interconnection cables together with the AC power cord.

CD Player, MD Deck, etc. Amplifier

DIGITAL OUT

REC PLAY

A

DIGITAL IN terminal

To record digital audio signals, connect this terminal to the digital output terminal of a

digital device such as a CD player with a commercially available optical digital cable.

B

ANALOG IN/OUT jacks

Analog 2-channel audio signal is input or output from these jacks. Connect these jacks to

the amplifier with RCA cables.

CD-RW890MK@

Amplifier

ANALOG OUT q

CD-R (TAPE) PLAY

ANALOG IN q

CD-R (TAPE) REC

Make sure to connect:

white plug q white jack (L: left channel)

red plug q red jack (R: right channel)

C

AC Power Cord

After all other connections are complete, connect the plug to the AC wall socket.

Be sure to connect the power cord to an AC outlet which supplies the correct voltage.

Hold the power plug when plugging or unplugging the power cord. Never pull or yank

on the power cord.

< If the unit will not be used for a long period of time, unplug the power cord.

AC Outlet

8

Unit Functions and Remote Control

J

I

J

F

H

G

a

d

e

f

g

h

i

b

c

A

B

C

D

Q

P

O

N

M

L

K J

E

F

G

H I

Only on Remote control unit

a

Numeric buttons

Use these buttons to select track numbers.

b

REPEAT (1/ALL, A-B)

Use these buttons to select a repeat mode.

c

Search (m/,)

Use these buttons to search for a part of a track.

d

TIME

Use this button to change the display mode.

e

PROGRAM

Use this button to program tracks.

f

CLEAR

Use this button to clear programmed tracks.

g

PROGRAM CHECK

Use this button to check the programmed contents.

h

SHUFFLE

Use this button for shuffle playback.

i

Skip (.//)

Use these buttons to skip tracks.

Note:

To simplify explanations, instructions in this manual refer

to the names of the buttons and controls on the front panel

only. Associated controls on the remote control will also operate

similarly.

9

ENGLISH

Main unit and Remote control unit

A

POWER

Press this button to turn the unit on or off.

B

Display

The total number of the tracks, the total play time of the disc, etc.

are displayed.

C

Disc Tray

D

OPEN/CLOSE (L)

Use this button to open and close the disc tray.

E

MUSIC SKIP (.//)

Use these buttons to skip tracks.

Hold down these buttons to search for a part of a track.

F

Play (y)

Use this button to start playback, recording, finalizing, unfinalizing

and erasing.

G

Pause (J)

Use this button to pause playback or recording.

H

Stop (H)

Use this button to stop playback or recording.

I

RECORD

Use this button to enter record pause mode. During recording, use

this button to divide tracks.

J

REC LEVEL

Use these buttons to adjust the analog recording level.

K

PHONES

For private listening, first reduce the volume level to minimum.

Then insert the plug from your headphones into the PHONES jack,

and adjust the volume by turning the LEVEL knob.

L

INPUT SELECT

Use this button to select a source to be recorded.

M

AUTO/MANUAL

Use this button to select the mode of track number assignment.

N

SYNC 1/ALL

Use this button for digital synchronized recording.

O

FINALIZE

Use this button to finalize a CD-R/CD-RW disc.

P

ERASE

Use this button to erase or unfinalize a CD-RW disc.

Q

REMOTE SENSOR

When operating the remote control unit, point it towards the

REMOTE SENSOR.

The provided remote control unit allows the unit to be operated

from a distance. When operating the remote control unit, point it

towards the REMOTE SENSOR on the front panel of the unit.

< Even if the remote control unit is operated within the effective

range, remote control operation may be impossible if there are any

obstacles between the unit and the remote control.

< The remote control may not work if the remote sensor is exposed

to direct sunlight or electric lighting. In this case, move the main

unit.

< If the remote control unit is operated near other appliances which

generate infrared rays, or if other remote control devices using

infrared rays are used near the unit, it may operate incorrectly.

Conversely, the other appliances may operate incorrectly.

Battery Installation

1

Remove the battery compartment cover.

2

Insert two “AA” (R6, SUM-3) dry batteries. Make sure that the

batteries are inserted with their positive “+” and negative“_” poles

positioned correctly.

3

Close the cover.

Battery Replacement

If the distance required between the remote control unit and main

unit decreases, the batteries are exhausted. In this case replace the

batteries with new ones.

For more information about collection of batteries, please contact

your local municipality, your waste disposal service or the point of

sale where you purchased the items.

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

< Be sure to insert the batteries with correct positive “+” and

negative “_” polarities.

< Use batteries of the same type. Never use different types of

batteries together.

< Rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

< When the remote control unit is not to be used for a long time

(more than a month), remove the batteries from the remote

control unit to prevent them from leaking. If they leak, wipe

away the liquid inside the battery compartment and replace the

batteries with new ones.

< Do not heat or disassemble batteries and never dispose of old

batteries by throwing them in a fire.

< Do not carry or store batteries with metal accessories. Doing so

may cause short-circuiting, leakage, breakage, etc.

Remote Control Unit

10

1

Press the OPEN/CLOSE (L) button.

The disc tray is opened.

2

Place a disc on the tray with the disc label side up.

< Never place more than one disc on the tray.

< The disc must be placed in the center of the disc tray. If the disc

is not correctly loaded, it may not be possible to open the tray

again once it has closed, so you should ensure the disc is always

centered on the tray.

< Do not force the tray by hand during opening and closing

operations.

3

Press the OPEN/CLOSE (L) button to close the tray.

The tray is closed. Take care that you do not catch your fingers in

the tray.

< It takes a few seconds for the unit to load the disc. No buttons will

work during loading. Wait until the total number of the tracks and

the total play time of the disc are displayed.

Turning on the power

Press the POWER button to turn on the unit.

Using Headphones

For private listening, first reduce the volume level to minimum.

Then insert the plug from your headphones into the PHONES jack,

and adjust the volume by turning the LEVEL knob.

When turning the power on/off, unplug the headphones. Failure

to observe this precaution may cause a noise to be produced.

Basic Operation Basics of Playback

11

ENGLISH

The disc type indicator shows the type of disc currently loaded.

CD:

A commercial pre-recorded CD

CD-R:

A finalized CD-R

CD-RW:

A finalized CD-RW

CD-R

NO TOC

:

A CD-R which has yet to be finalized

CD-RW

NO TOC

:

A CD-RW which has yet to be finalized

< As for non-audio discs, the content may be detected but will not

be played.

< When no disc is inserted, “NO DISC” appears.

4

Press the PLAY (y) button to start playback.

Disc playback starts from the first track.

< If you load the disc, and then press the Play (y) button without

closing the disc tray, the disc tray closes automatically and

playback starts.

< When the track number changes during playback of continuous

music such as live performances, the sound may be cut then

played.

To pause playback

Press the Pause (J) button during playback. Playback stops at the

current position. To resume playback, press the Play (y) button or

the Pause (J) button.

To stop playback

Press the Stop (H) button to stop playback.

To skip to the next or previous track

During playback, repeatedly press the Skip (.or/) button

until the desired track is found. You can also skip to next or

previous tracks rapidly by holding down the Skip (.or/)

button of the remote control unit. The selected track will be

played from the beginning.

In the stop mode, press the Skip (.or/) button repeatedly

until the track you want to listen to is found, and press the Play (y)

button to start playback from the selected track.

< When the . button is pressed during playback, the track

being played will be played from the beginning. To return to the

beginning of the previous track, press the . button twice.

< During programmed playback, the playback skips to the previous

or next track in the program.

Search for a part of a track

During playback, hold down the Skip (. or /) button of

the main unit and release it when the part you want to listen to is

found.

Use the Search (m or ,) button when operating with the

remote control unit.

disc type indicator

total number of the tracks total play time of the disc

12

Direct Playback Shuffle Playback

While in stop or playback mode, you can use the numeric buttons of

the remote control unit to select a track.

Playback starts from the selected track.

< If the above operation is performed while paused, playback will be

paused at the beginning of the selected track.

< Direct playback is not possible during shuffle playback and

programmed playback.

During playback, press the SHUFFLE button so that the tracks can be

played randomly.

In the stop mode, press the SHUFFLE button, then the Play (y)

button.

When the shuffle playback of all the tracks has been finished, the

unit stops and the shuffle playback mode is cancelled.

< If you press the / button during shuffle playback, next track

will be randomly selected and played. If you press the .

button, the currently played track will be played from the

beginning. A track cannot be replayed during shuffle playback.

< Shuffle playback does not work during programmed playback and

A-B repeat.

< A-B repeat does not work during shuffle playback.

< Shuffle playback works with finalized discs only.

< If one of the following buttons is pressed, shuffle mode will be

cancelled:

SHUFFLE (while in the stop mode), OPEN/CLOSE (L), POWER

< When the SHUFFLE button is pressed during REPEAT 1 playback, all

tracks are played in a random order.

track 7:

track 10:

13

ENGLISH

Time Display

Each time the TIME button is pressed, the display changes as

follows:

CD/CD-R/CD-RW playback

Unfinalized CD-R/CD-RW, stopped

During recording / While recording is paused

Each time the REPEAT button is pressed, the repeat mode changes

as follows:

REPEAT ALL (Repeat all the tracks)

All the tracks of the disc will be played repeatedly.

REPEAT 1 (Repeat one track)

The track being played will be played repeatedly. If you press the

Skip (.//) button and select another track, the track you

selected will be played repeatedly.

It is also possible to select a track to be repeated in the stop mode.

Press the REPEAT button twice and then select the track number

by pressing the Skip (.//) button. Press the Play (y) button

to start playback.

< REPEAT ALL or REPEAT 1 playback works with finalized discs only.

< If one of the following buttons is pressed, repeat mode will be

cancelled:

OPEN/CLOSE (L), POWER

< During shuffle playback, REPEAT 1 cannot be selected.

REPEAT ALL REPEAT 1

Repeat Playback

elapsed time of the current track

(Ex.)

time remaining for the current track

total elapsed time of the disc

time remaining for the disc

total play time of the disc

total number of the tracks remaining recording time of the disc

(Ex.)

elapsed recording time of the disc

remaining recording time of the disc

(Ex.)

(off)

14

Up to 32 tracks can be programmed in the desired order.

< Insert a disc before beginning programming.

< Programmed playback works with finalized discs only.

1

Press the PROGRAM button in the stop mode.

“PROGRAM” indicator blinks, and “0P00” appears on the display.

2

Press the numeric button to select a track.

The selected track is programmed. To program more than one

track, press the numbers subsequently.

You can also use the Skip (.//) button and the PROGRAM

button to program tracks. Select a track using the Skip (.//)

button, and press the PROGRAM button. Repeat this step to

program other tracks.

< If you made a mistake, press the CLEAR button. The last

programmed number will be deleted.

< To stop programming, press the Stop (H) button. The program

indicator (PROGRAM) stops blinking and lights up. When the

PROGRAM button is pressed again, the “PROGRAM” indicator starts

blinking again, and you can continue programming.

Programmed Playback (1)

You can play back the designate point of track repeatedly.

Start playback and designate the point at which the A-B repeat

should start (point A) by pressing the A-B button.

“REPEAT A-” blinks on the display.

When the point at which repeat playback should end (point B) is

reached, press the A-B button again.

The designated section will be played repeatedly.

< The interval between points A and B must be 10 seconds or longer.

< CD-R/CD-RW discs that have not been finalized cannot be used for

A-B repeat.

< After designating point A, the Search (m/,) button can be

used to fast-forward or fast-backward to point B.

Note that the point B should be forward the point A. Do not go

back beyond the point A.

< The Skip (.//) buttons do not work during A-B repeat.

< A-B repeat does not work during programmed playback and

shuffle playback.

< Shuffle playback does not work during A-B repeat.

< If one of the following buttons is pressed, A-B repeat will be

canceled:

A-B, Stop (H), OPEN/CLOSE (L), POWER

A-B Repeat

track 7:

track 10:

total time of the programmed tracks

track number program number

15

ENGLISH

3

When the selection of track numbers has been finished,

press the Play (y) button to start program playback.

The “PROGRAM” indicator stops blinking and lights up. Playback of

the program starts.

To check the programmed order

In the stop mode, press the PROGRAM CHECK button repeatedly to

show the track numbers that have been stored in memory.

< This cannot be used while the “PROGRAM” indicator blinks.

To add a track to the end of the program

1

Press the PROGRAM button in the stop mode.

2

Press the numeric button to select a track.

The track is added to the end of the program.

To overwrite the program

1

In the stop mode, press the PROGRAM button repeatedly

until the program number to be changed appears on the

display.

2

Press the numeric button to select a track.

The track is overwritten to the selected track.

Continue to the next page

track 7:

track 10:

track 7:

track 10:

16

Programmed Playback (2)

To delete a track from the program

1

In the stop mode, press the PROGRAM CHECK button

repeatedly until the program number to be deleted

appears on the display.

2

Press the CLEAR button.

The track is removed from the program, and the program numbers

of the following tracks are moved up.

To clear the program

In the stop mode, hold down the CLEAR button for more than 2

seconds.

If one of the following buttons is pressed, the programmed contents

will also be cleared.

OPEN/CLOSE (L), POWER

About Recording

CD-R and CD-RW

A CD-R disc can be recorded only once. Recorded tracks cannot be

erased. However, if some recording time is still available, additional

recording is possible. If you finish recording and finalize the CD-R

disc, it can be played with a normal CD player. (Some CD players

may not be compatible.)

On a CD-RW disc, even if no recording time is available, you can

erase tracks already recorded and record tracks repeatedly. You can

erase all tracks at once or the last track only. However, you cannot

erase only tracks in the middle of the disc.

CD-RW discs can only be played with compatible CD players.

Serial Copy Management System

This unit is in compliance with the Serial Copy Management

System standard. This standard has been established to restrict

digital-to-digital copying to only the first generation. The basic

rules governing this system are as follows:

Rule 1

A digital recording is possible from a digital source such as a CD,

DAT or MD onto a recordable CD-R, CD-RW, MD or DAT through

a digital input connection. However, further digital to- digital

recording is prohibited for the second and later generations.

Rule 2

When an analog source such as an analog disc or FM broadcast

is digitally recorded by using a CD-R, CD-RW, MD or DAT, this

recorded source can be digitally recorded on another CD-R,

CD-RW, MD or DAT. However, further digital copying is prohibited.

17

ENGLISH

Before you start recording, make sure that you understand

the following points:

<

Up to 99 tracks can be recorded according to the CD standards.

When a 100th track is about to be recorded, recording will stop

automatically.

<

A track less than 10 seconds in length on an audio CD cannot be

recorded .

<

If the Stop

(H)

button or Pause

(J)

button is pressed within 10

seconds from the beginning of a track, the unit continues to

record no signal and stops when the track’s length reaches 10

seconds.

<

When recording is finished, “PMA WRITE” blinks for a few seconds,

and then the unit goes into the stop mode. Do not apply shock or

vibration to the unit while recording or “PMA WRITE” blinks.

<

When the available recording time reaches 0, recording will stop

automatically.

<

If a half-way recorded disc is inserted, recording continues next to

the last recorded track.

<

You can add tracks to an unfinalized recordable disc. Once

finalized, a CD-R disc is “fixed” and behaves in the same way as a

CD. Finalized CD-RW discs, however, can be unfinalized, erased and

re-recorded.

<

When the auto track function is used, the tracks are separated

based on the specified level. Therefore, if a silent part is contained

at the beginning or in the middle of a track, the playback time may

not be the same as the actual length of the track.

<

When track numbers are added to continuous music such as live

performances, the sound is cut a moment.

<

If a disc recorded with this unit is played with another player,

noises may occur when the track changes.

Before Recording

1

Load a recordable CD-R or CD-RW disc into the unit.

Press the OPEN/CLOSE (L) button, place a disc on the disc tray

with the disc label side up, and then press the OPEN/CLOSE (L)

button to close the disc tray.

Make sure “NO TOC” and “CD-R” (or “CD-RW”) indicator lights on

the display.

2

Select the source to be recorded using the INPUT SELECT

button.

Each time the INPUT SELECT button is pressed, the display changes

as follows:

DIGITAL (OPTICAL IN)

Select this to record a source connected to the DIGITAL IN terminal.

ANALOG (ANALOG IN)

Select this to record a source connected to the ANALOG IN

terminal.

< The input source cannot be changed during recording.

3

Select the mode of track number assignment using the

AUTO/MANUAL button.

When the AUTO/MANUAL button is pressed once, the current

increment level is displayed. Press the AUTO/MANUAL button

repeatedly to select another setting.

MANUAL

S-LVL -60 S-LVL -50

S-LVL -40 S-LVL -30

A-TIME xx*

* Appears only when using ANALOG input

< After 2 seconds have passed, the display returns to the track/time

display.

Recording (1)

Continue to the next page

18

Recording (2)

S-LVL-60/50/40/30

Track numbers are added automatically when silence is detected.

The auto track function activates and “A-TRACK” appears. The

displayed number indicates the increment level.

The track numbers are automatically added during recording. If

a track change is detected via DIGITAL or if silence (lower than

the increment level**) continues for three seconds or longer

then the next track starts (when sound becomes louder than

the increment level) via ANALOG, and the track numbers are

automatically updated.

** Increment level

Sound level to detect “silence” to add track numbers using auto

track when recording from external devices via ANALOG or to

perform synchronous recording for digital sources such as CD, MD,

and DAT.

This instruction manual describes “silence” as the situation where

the recording source level is lower than the specified increment

level.

−60, −50, −40, and −30 dB can be selected.

A-TIME

Track numbers are added at the set time intervals. This is only

enabled when using ANALOG input.

“A-TRACK” appears on the display when the auto track function is

on. The number shows the time increment used. Track numbers

will be added automatically during recording. Use the skip

(.//) buttons to set the time interval for adding track

numbers. The interval can be set to 1–10 minutes in one-minute

increments.

The track number will not change if the next track started after

analog audio input was silent (less than the set increment level) for

3 or more seconds.

MANUAL

Track numbers will not be added automatically.

To add track numbers manually, press the RECORD button.

< The setting can be configured for DIGITAL and ANALOG

respectively. When the power is turned on, the setting is –60dB for

DIGITAL, and –50dB for ANALOG.

< The setting is stored until the power is turned off.

< If a CD is recorded via DIGITAL, the track numbers are added based

on the CD's digital signals. There is usually no need to change the

increment level.

< In digital recording, even if the auto track function is activated, track

numbers may not be added depending on the digital source player.

In such a case, add track numbers manually (see page 19).

< When you record digital broadcasts or other sources without

track numbers, track numbers are not added even if the auto track

function is activated. To add a track number, press the RECORD

button while recording a track.

< When you record classical music or other sources containing silent

parts via ANALOG, track numbers may not be properly added even

if the auto track function is activated. To add a track number in this

case, deactivate the auto track function, and press the RECORD

button while recording a track.

< When you record a record or other sources with much

interference, more track numbers than expected may be added

unintentionally.

< The AUTO/MANUAL button cannot be used during recording.

If track numbers are not properly added

When you record sources with interference via ANALOG, track

numbers may not be added if the increment level is lower than the

interference level. In this case, set the increment level higher than

the interference level.

If there is little interference and the track starts with a small sound

resulting in the beginning of the recorded track being truncated,

set the increment level lower.

4

Press the RECORD button.

and J indicators on the display will light, and the unit

enters the record pause mode.

< No button will work while “WAITING” is displayed. Wait a few

seconds until “WAITING” disappears from the display. When

DIGITAL is selected in step

2

, the sampling frequency of the

digital source (“FS 44_1K”, “FS 48K” or “ FS 32K”) briefly appears

after “WAITING”.

< “DIN UNLOCK” appears when the unit cannot perceive the digital

signal. In that case, connect a digital device to the DIGITAL IN

terminal, switch it on, and wait a few seconds until the unit enters

the record pause mode.

< You cannot record if “MONITOR” appears on the display. In that

case, reload a recordable disc, wait a few seconds until “NO TOC”

and “CD-R” (or “CD-RW”) indicators light on the display, then press

the RECORD button again.

5

If necessary, adjust the recording level using the REC LEVEL

buttons.

The recording level can be adjusted only when “ANALOG” is

selected in step

2

.

The recording level is 0 dB when the power is turned on. Usually,

recording is possible even if the recording level has not been

adjusted.

19

ENGLISH

Play the source to be recorded and adjust the recording level so

that the loudest sound does not exceed the “OVER” indicator on

the peak level meter.

The level can be adjusted as follows:

< When the POWER button or the Stop (H) button is pressed, the

recording level is reset to 0 dB.

< The volume level differs depending on the source (record, cassette

tape, CD, etc.). To record various sources at the appropriate volume,

the recording level should be adjusted for each source.

6

Press the Play (y) or the Pause (J ) button to start

recording.

Recording starts.

7

Play the source to be recorded.

When the playback of the source has been finished, press the Stop

(H) button to stop recording.

To stop recording

Press the Stop (H) button to stop recording.

< If the CD-R is finalized, it can be played with another CD player.

To pause recording

Press the Pause (J) button. “WAITING” briefly appears on the

display, then recording is paused.

To restart recording, press the Play (y) button or the Pause (J)

button.

< You cannot restart recording while “WAITING” is displayed.

< Remember that every time recording is paused or stopped, a new

track number will always be assigned. It is not possible to record in

two “stages” within one track.

To monitor the input signal

When no recordable disc is loaded in the unit, press the RECORD

button.

“MONITOR” appears on the display, and you can monitor the input

source via the PHONES jack and the output terminals. The meters

show the current input level.

Exit the monitor mode by pressing the Stop (H) button.

Manual track division

It is possible to divide a track into multiple tracks by pressing the

RECORD button while recording.

< Manual track division is possible regardless of the AUTO/MANUAL

setting.

< A track cannot be less than 10 seconds in length. The RECORD

button will not work if it is pressed within 10 seconds from the

beginning of a track.

0 dB–

∞

+12 dB−60 dB

MIN. DOWN UP MAX.

20

Synchronous Recording

The convenient synchronous recording function automatically starts

recording when receiving analog or digital signals from an externally

connected device such as a CD player and MD deck, and stops

recording when signal reception is complete.

For CD, MD, or DAT, synchronous recording starts when a digital

signal is detected, which is the beginning of a track. Synchronous

recording stops if there is a period where the sound is quieter than

the specified increment level lasting five seconds.

For digital sources other than the above or analog sources,

synchronous recording starts when a sound louder than the

specified increment level is detected. Synchronous recording stops

if there is a period where the sound is quieter than the specified

increment level lasting 8 seconds.

1

Load a recordable CD-R or CD-RW disc into the unit.

Press the OPEN/CLOSE (L) button, place a disc on the disc tray

with the disc label side up, and then press the OPEN/CLOSE (L)

button to close the disc tray.

2

Select the source to be recorded using the INPUT SELECT

button.

3

Select the mode of track number assignment using the

AUTO/MANUAL button.

4

Press the SYNC 1/ALL button and select “SYNC 1” or “SYNC

ALL”.

5

Press the RECORD button.

and J indicators on the display will light, and the unit

enters the record pause mode.

< The Play (y) button and Pause (J) button cannot be used during

synchronous recording.

6

Start playing the source.

< If no sound is heard for 5 seconds or longer during synchronous

recording, recording stops. To record the music with such periods

of silence, turn off synchronous recording. After turning off

synchronous recording, start recording manually, then play the

source to be recorded.

< Press the Stop (H) button to stop the recording manually.

< If you press the Stop (H) button or the Pause (J) button during

recording, the synchronous recording function will be cancelled.

< The synchronous recording function automatically turns off after

recording.

< The SYNC 1/ALL button cannot be used during recording or in the

record pause mode.

< When “SYNC ALL” is selected, the auto track function is always on.

Select –60, 50, 40 or 30 dB using the AUTO/MANUAL button.

< Even if the AUTO/MANUAL button is set to MANUAL, the auto track

function will be on during synchronous recording. The increment

level is set to –60 dB (–50 dB when recording via ANALOG). The

setting automatically returns to MANUAL after the recording.

< In digital recording, synchronous recording may not start

depending on the digital source player. In such a case, start and

stop recording manually.

< To prevent the beginning of a track from being cut off, manually

start recording by pressing the Play (y) button before you play

the source to be recorded.

Page is loading ...

TEAC CD-RW890MK2-B User manual

This manual is also suitable for

TEAC CD-RW890MK2-B User manual

in other languages

Related papers

Other documents