Alpine 2013 Full-Size Truck Installation guide

Alpine
Brand
Alpine
Model
2013 Full-Size Truck
Category
Car navigation systems
Type
Installation guide

This manual is also suitable for

Chevrolet/GMC
FULL SIZE TRUCK & SUV 1/20
CHEVROLET/GMC
Model: Full Size Truck and SUV
Model Year: 2007-2014
Trim Level: All
Introduction
Design and specifications are subject to change without notice for improvement.
To Ensure Safe Use, Always Follow These Precautions
The installation of this product requires specialized skills and experience. We recommend that you have the
product installed by the store that you purchased it from.
Before you use this product, be sure to carefully read this installation manual and the separate user's manual
so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as
a result of failure to follow the instructions in the manuals.
This manual includes a number of symbols that are intended to help you use the product safely, to prevent
harm to you and others, and to protect against damage to property. These symbols and their meanings are
listed below. Make sure you fully understand these symbols before you begin reading the main text.
Explanations of Injury and Damage That May Result from Incorrect Use
Warning
Ignoring the content marked by this indication and using the product incorrectly is
expected to lead to death or serious injury.
Caution
Ignoring the content marked by this indication and using the product incorrectly is only
expected to lead to injury or property damage.
CHEVROLET
Model Year
SILVERADO LTZ 2007 - 2013
AVALANCHE 2007 - 2013
SUBURBAN 2007 - 2014
TAHOE 2007 - 2014
GMC
SIERRA SLT 2007 - 2013
YUKON 2007 - 2014
YUKON XL 2007 - 2014
* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is
not guarantee if the manufacturer has made production changes to the listed vehicles above.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 2/20
Types of Precautions
Forbidden
Indicates actions that are forbidden
(must not be performed)
Mandatory
Indicates actions that are
mandatory (must be performed)
Forbidden
Indicates that disassembly is
forbidden.
Marks content that should receive
your full attention.
Warning
Do not disassemble or modify the product. Doing so could lead to an accident, re,
or electric shock.
Forbidden
Store screws and other small objects where small children cannot reach them. If one of these
small objects is swallowed, consult with a doctor immediately.
When replacing fuses, be sure to use fuses with the specied current rating. Failing to do so could
lead to an accident or re.
Forbidden
Mandatory
Only connect the product to a 12 VDC negative ground car. Failing to do so could lead to
an accident or re.
Mandatory
Before you begin wiring, remove the ground wire from the negative terminal of the battery.
Failing to do so could lead to electric shock or injury.
Do not cut the insulation on a cord and take power from another device. Doing so could
lead to re or electric shock.
Forbidden
Do not install the product in a location where it will obstruct the driver’s forward view;
interfere with the operation of the steering wheel, gearshift, or the like; or pose a
threat to passengers. Doing so could lead to an accident or injury.
Forbidden
When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank,
electrical wiring, and the like. This kind of damage could lead to an accident or re.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 3/20
When installing and grounding the product, do not use any of the bolts or nuts of the
steering wheel, brakes, fuel tank, or the like. Doing so could make the brakes stop working
or lead to re.
Forbidden
Do not install the product near the passenger-side airbag. Doing so could interfere with the
operation of the airbag and lead to an accident or injury.
Forbidden
Bundle cords so that they don’t interfere with driving. Wrapping cords around the steering
wheel, gearshift, brake pedal, or the like, could lead to an accident or damage equipment.
Caution
Connect the product properly according to the instructions. Failing to do so could lead
to re or an accident.
Forbidden
Do not sandwich cords between the seat railing or allow them to touch protrusions.
Resulting breaks or shorts could lead to electric shock or re.
Do not block vents or heat sinks. Doing so could lead to re or damage equipment.
Use the accessories according to the instructions, and attach them securely.
Failing to do so could lead to an accident or damage equipment.
Forbidden
Do not install the product where it may be exposed to water or in a place with high levels
of humidity or dust. Doing so could lead to re or damage equipment.
Forbidden
The installation and wiring of this product requires specialized skills and experience.
Have the product installed and wired by the store that you purchased it from.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 4/20
Accessory List
Head Unit Box Parts (X009)
Owner’s Manual Disc X009 Head Unit X009 Camera Harness
AUX/Pre Out Harness GPS Antenna USB Extension Cable
8mm x 8 Screws Quick Reference Guides Registration Cards
QRG
Audio
QRG
Navigation
Alpine
Registration Card
NAVTEQ
Registration Card
iDatalink Maestro Box Parts (ALP-MRR/ALP-HRN-GM)
Main Harness Navigation Adapter Bose Adapter Harnesses
Rear Seat A/V Harness Chime Speaker USB to Mini USB Cable
Vehicle Camera Harness iDatalink Maestro Module
Chevrolet/GMC
FULL SIZE TRUCK & SUV 5/20
Installation Kit Parts (G-KTX-009-GM)
X009-GM Key Panel Key Harnesses Side Mounting Brackets
Screws x 12 Rear Support Bracket 8mm Screw x1
Cutout Template
Optional 3rd-Party Parts (Not Included)
PAC GMRVD2
*1
RCA A/V to 3.5 mm Adapter
*1
Needed with 2012-2014 Navi-equipped models.
Audio L
3.5 mm A/V
Audio R
Video
Allows front panel A/V input
to be used when vehicle is
equipped with factory rear seat
entertainment.
*2
*2
Note: To use this option, aux-3 input must be
switched from iPod video to aux-3 in the “aux-3
source select” menu.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 6/20
Component Locations
GPS Antenna Location
Head Unit
Chime
Speaker
GPS Antenna
Maestro/Speaker Location
Maestro/Speaker
Location
Top View
Front side center console driver side view
Maestro/Speaker
Location
Chevrolet/GMC
FULL SIZE TRUCK & SUV 7/20
X009-GM System Wiring for All Non-Navigation Equipped Vehicles And 2007-2011 Navigation-
Equipped Vehicles
Chime Speaker
X009 Camera
Harness
Camera Input Back-up
Camera In
HDMI Input
USB Extension
Cable
To SXM
Aux/Pre-out
Harness
X009 Head Unit
To X009-GM
Key Panel
GPS Antenna
Subwoofer
10-pin Green
Connector
3.5 mm Mini plug
10-pin Black
Connector
4-pin Black
Connector
Main Harness
18-pin Black
Connector
To Overhead
Screen
Center Out
Sub Out
Aux Output
PurpleRed
GreenWhite
GrayRed
WhiteWhite
Aux Input
Front
Rear
Front Rear A/V
Input
3-pin Black
Connector
4-pin Data
Connector
Blue Power Antenna
(Not used)
Green/
White
Blue/White Amp Turn-on
3.5 Mini plug
Speed Pulse
4-pin Data Connector
To ODB II
Connector
iDatalink MAESTRO Module
To Vehicle Connectors
Rear seat A/V
Harness
Vehicle Camera
Harness
Use only with aftermarket
amplifiers
Connect if factory-equipped using
RCA Y-cable to front RCA outputs
Connect if factory-equipped
X009
Power
Harness
If Bose is equipped,
connect Bose
adapter harness on
vehicle side.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 8/20
X009-GM System Wiring for 2012-14 Navigation Equipped Vehicles
To retain a pre-existing factory rearview camera
• Locate the 20-pin radio plug , connect the PINK or WHITE wire located at pin 5 to the center of yellow conductor of a yellow RCA, connect
the LIGHT BLUE or BARE wire located at pin15 to the shield of the yellow RCA.
X009 Head Unit
To X009-GM
Key Panel
Main Harness
Chime Speaker
X009 Camera
Harness
Camera Input Back-up
Camera In
HDMI Input
USB Extension
Cable
To SXM
Aux/Pre-out
Harness
GPS Antenna
Subwoofer
10-pin Green
Connector
3.5 mm Mini plug
10-pin Black
Connector
4-pin Black
Connector
18-pin Black
Connector
To Overhead
Screen
Center Out
Sub Out
Aux Output
PurpleRed
GreenWhite
GrayRed
WhiteWhite
Aux Input
Front
Rear
Front Rear A/V
Input
3-pin Black
Connector
4-pin Data
Connector
Blue Power Antenna
(Not used)
Green/
White
Blue/White Amp Turn-on
3.5 Mini plug
Speed Pulse
4-pin Data Connector
To ODB II
Connector
iDatalink MAESTRO Module
To Vehicle Connectors
Use PAC GMRVD2
or equivalent
Navigation
Adapter
Vehicle Camera
Harness
Use only with aftermarket
amplifiers
Connect if factory-equipped using
RCA Y-cable to front RCA outputs
Connect if factory-equipped
X009
Power
Harness
If Bose is equipped,
connect Bose
adapter harness on
vehicle side.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 9/20
Factory unit disassembly process
1 Use a panel removal tool to carefully unsnap the
trim bezel around the radio and HVAC controls.
2 Extract (8) 9/32” – 7mm screws securing the radio,
HVAC and cigarette lighter panel. Disconnect and
remove in the order shown.
3 Remove and disconnect by order number shown.
4 Remove driver side center console panel by
unsnapping it
5 Move the factory wire harness to the back of the
dash by accessing through the drivers side center
console area.
3
2
1
Chevrolet/GMC
FULL SIZE TRUCK & SUV 10/20
Steps to Get Started
1 INSTALL THE WEBLINK PLUG-IN
Go to:
idatalinkmaestro.com/plugin and follow the installation steps.
Review the System Requirements before installing.
If the plugin is already installed, the caution, “The plugin is already
installed” appears. Please skip to step 2.
2 REGISTER A WEBLINK ACCOUNT
Go to:
idatalinkmaestro.com/register and complete the registration process.
A conrmation email will be sent to you requiring validation.
For existing customers, click log in.
For existing customers, click log in.
3 CONNECT YOUR MAESTRO MODULE
Use the included USB cable to connect your Maestro module to your
PC.
4 LOG INTO WEBLINK
Go to:
idatalinkmaestro.com/login.
Enter your username and password, then click OK.
5 PROGRAM YOUR MODULE
Follow the programming steps for your vehicle.
6 COMPLETE INSTALLATION
Proceed to the next page to complete installation.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 11/20
Installation Instructions
1 Attach the Maestro module to the X009 main
harness.
2 Attach the chime speaker to the side of the center
console.
3 Insert the radio side of the main harness from
behind the dash to the radio cavity.
4 Connect factory harness to the X009 main harness
and secure it.
5 Place the GPS antenna on the top dash are as
illustrated and feed the cable in between the A/C
vents. Use the supplied magnetic base for the
best signal strength.
5
6 Access the OBDII connector located under the
driver side dashboard. Connect the BROWN /RED
wire from the Alpine harness to the TAN/BLACK
wire located at pin 6 of the OBDII connector.
Connect the BROWN /YELLOW wire from the
Alpine harness to the TAN wire located at pin 14 of
the OBDII connector.
7 Connect the X009 main harness to the headunit
and test all functions before snapping the
headunit bezel into the dashboard.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 12/20
Exploded-View Diagram
Parts assembly diagram for the X009-GM kit.
Switch panel assembly
X009 AVN Unit
Rear support bracket
Left spacer
Left bracket
Factory dash bezel
Right bracket
Right spacer
Factory HVAC controller (not supplied).
Requires trimming for proper t, refer to page 15.
Factory cigarette lighter panel (not supplied).
Needs trimming for proper t, refer to page 16.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 13/20
Bracket Assembly Procedure
Attach pre-assembled left and right bracket assemblies to the X009 unit using 4 supplied M5x8 bolts on each side.
Left bracket assembly
M5X8
X009 AVN Unit
M5X8
Rear support bracket
M5X8
Right bracket assembly
Bracket and spacer are
pre-assembled in the
X009-GM package.
Clip
Chevrolet/GMC
FULL SIZE TRUCK & SUV 14/20
Wiring Installation Procedure
Connect and route wires 1 and 2 as shown in the diagrams below.
Pass through
7-pin
20-pin
12-pin
12-pin
20-pin
20-pin
20-pin
12-pin
7-pin
To X009 key
panel connector
Rear View
Side ViewFront View
Bottom View
20-pin
7-pin
7-pin
12-pin
Chevrolet/GMC
FULL SIZE TRUCK & SUV 15/20
Trimming procedure for factory HVAC panel
The factory HVAC control needs to be trimmed to fit properly in the kit. Trim the top edges of the HVAC control as shown
in the diagram below.
+
–
+
–
+
–
+
–
+
–
+
–
Cut
out
Cut
out
Cut out
The included template can be used as a guide for
proper trimming.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 16/20
Trimming procedure for factory cigarette lighter panel
The factory cigarette lighter panel needs to be trimmed to fit properly in the kit. Trim the side and bottom edges of the
cigarette lighter panel as shown in the diagram below.
Cut out
Cut out
Cut out
Cut out
Cut out
Chevrolet/GMC
FULL SIZE TRUCK & SUV 17/20
Installing the X009-GM assembly
Attach the X009-GM assembly into the dash using 8 provided 4x12mm screws, 4 on each side.
Instrumental panel
Provided screws
X009 ASSY
Screw is close to the Monitor.
Don’t damage the Monitor.
Attach the assembly to the vehicle’s dashboard
at these 8 points using the provided screws.
Chevrolet/GMC
FULL SIZE TRUCK & SUV 18/20
Re-installing the factory HVAC controls
Connect the factory HVAC harnesses, and install the factory HVAC controller using two of the supplied 4x12mm screws.
Factory HVAC controller
(not supplied)
Included 4x12mm screws
Chevrolet/GMC
FULL SIZE TRUCK & SUV 19/20
Re-install the factory cigarette lighter panel
Connect the factory harnesses to the factory cigarette lighter panel, and attach it to the kit using two of the supplied
4x12mm screws.
Factory cigarette lighter
panel (not supplied)
Included 4x12mm
screw
Included
4x12mm screw
Chevrolet/GMC
FULL SIZE TRUCK & SUV 20/20
Install the switch panel assembly
Connect Wire 1 and Wire 2 to the switch panel assembly, and push the cables into the dash as the panel is installed. Snap
the bezel into place to complete the installation.
Clips on rear side
(6points)
Switch panel assembly
Wire-1
Wire-2
Wire-2
Push wires into inst panel.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Alpine 2013 Full-Size Truck Installation guide

Alpine
Brand
Alpine
Model
2013 Full-Size Truck
Category
Car navigation systems
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents