CAME MI6010, MI6020, MI6110, MI6120 Installation guide

Documentazione

Tecnica

M85

rev. 2.0

03/2003

©

CAME

CANCELLI

AUTOMATICI

119PM85-GB

AUTOMATIC DOORS

ANTIPANIC BREAKTHROUGH SYSTEM

ONLY FOR MOBILE DOORSCTRIC CONTROL PANELS

ARMOIRESARMOIRES

ARMOIRES

DEDE

DE

COMMANDECOMMANDE

COMMANDE

SCHALTTAFEL

CUADROSCUADROS

CUADROS

DEDE

DE

MANDOMANDO

MANDO

MI

CANCELLI AUTOMATICI

10

20

MI6010 - 6110

MI6020 - 6120

COMPLETE MECHANICAL ENSEMBLE

to be applied on sliding opening frames.

In emergencies, it allows the OPENING of the ESCAPE EXIT

by BREAKING THROUGH THE DOORS.

Up to 120 kg per door

- pg. 2 -

pg. 3

pg. 4

pg. 5

pg. 8÷13

pg. 16÷19

pg. 20

pg. 21/22

pg. 23

pg. 24

- Operation and Use Limits

- Type of MI Antipanic System

- What the MI Package Contains

MI FOR COMMERCIAL SERIES

- Section types and special instructions for door construction

MI FOR CAME S40 SERIES

- Section Types

- MI Antipanic Bar Machining

- Mounting of MI Antipanic System

- Spiral cable application and mobile door mounting

- Power connections

TABLE OF CONTENTSTABLE OF CONTENTS

TABLE OF CONTENTS

- pg. 3 -

Sliding door INTERNAL MOUNTING solution:

Antipanic breakthroughs are successful only IF THE DOOR

IS FULLY CLOSED, not during movement.

The sliding door's operation can be restarted simply by moving

the door/doors to the side.

Sliding door EXTERNAL MOUNTING solution:

Complete antipanic breakthrough can be achieved NO

MATTER WHAT POSITION THE SLIDING DOORS ARE

IN during movement;

This is the preferred solution to fully exploit the characteristics

of the antipanic breakthrough system.

Also in this case the sliding door's operation can be restarted

simply by moving the door/doors to the side.

INTERNO

locale da evacuare

ESTERNO

locale da evacuare

INTERNO

locale da evacuare

ESTERNO

locale da evacuare

EMPLOYMENT LIMITS

OPERATION and USE LIMITSOPERATION and USE LIMITS

OPERATION and USE LIMITS

htdiW A

)mm(

ELGNIS

ROOD

)gk(thgiew.xaM

repdettimda

ROODELGNIS

htiW ASROC

citamotua

metsys

htiW OEDOR

citamotua

metsys

005 57 021

006 57 09

007 57 08

008 06 07

009 05 06

0001 54 05

0011 04 04

ehtfognitnuomehT 3714P sileehw

yrotadnamrevohtiw 0011 otpudna

0051 (mm 0216IM/0116IM .)

For MI6010 and MI6020 (door width of up to 1100 mm),

the maximum weight for each door indicated can be increased

by attaching a sliding wheel on the ground (part. P4173, pages

5 & 13).

WARNING: if the P4173 sliding wheel is added, the

adequate linearity of the plane on which it must turn must be

ensured.

- pg. 4 -

COMPLETE ANTIPANIC BREAKTHROUGH

SYSTEM FOR 2 SLIDING DOORS

with A up to 1100 mm = MI6010

with A up to 1500 mm = MI6110

A

AA

MOUNTING FROM

INSIDE THE

ROOM TO BE

EVACUATED

MOUNTING FROM

OUTSIDE THE

ROOM TO BE

EVACUATED

MOUNTING FROM

INSIDE THE

ROOM TO BE

EVACUATED

MOUNTING FROM

OUTSIDE THE

ROOM TO BE

EVACUATED with A up to 1100 mm = MI6020

with A up to 1500 mm = MI6120

Types of MI Antipanic SystemsTypes of MI Antipanic Systems

Types of MI Antipanic Systems

COMPLETE ANTIPANIC BREAKTHROUGH

SYSTEM FOR 1 SLIDING DOOR

- pg. 5 -

Antipanic breakthrough kit componentsAntipanic breakthrough kit components

Antipanic breakthrough kit components

LOWER HINGE FOR MOBILE DOOR

ANTIPANIC SYSTEM FOR MOBILE DOOR

UPPER JOINT

ANTIPANIC SPRING LATCH

FIXED UPPER SECTION

OPENABLE LOWER SECTION

HOOKING PLATES TO CARRIAGES

LOWER HINGE

MOBILE DOOR

FLOOR GUIDE

ANTE MOBILIANTE MOBILI

ANTE MOBILI

MI6010/6110 represented; in

MI6020/6120 the components are

doubled.

SLIDING WHEEL

CONTACT CAPS

Art. P4116

Art. P4117

Art. PM338A

Art. PM205

Art. PM207

Art. PM208

Art. PM209

Art. PM912

Art. PM911A

Art. P4173

Art. PL593

GUIDE STOP

Art. PM339A

Art. PM909

+PM910

+PM913

Art. C7039

Art. PL564

Art. PM576

Art. TB57

Art. PM923

Art. FN930

TERMINAL

COUPLING

SUPPORT

FIXING SUPPORT

SLIDING TUBE

SPIRAL CABLE

NYLON YARN

Art. PI405

RIP CORD 2X0,5

WARNING!It is a standard piece in all

set and it must be used in

applications in which the size of the

doors is not observed.

See pg. 3.

- pg. 6 -

This page left intentionally blank

- pg. 7 -

MI System

applied to

commercial series

of sections for

automatic sliding doors

The sections, sizes, weather strip and everything else

mentioned in the following pages as

commercial series

are

purely indicative and appear solely for the purpose of illustrating

the applicability of the MI system on sliding doors with frames

other than our series S40 type.

- pg. 8 -

istruzioni di montaggio per istruzioni di montaggio per

istruzioni di montaggio per SERIE COMMERCIALISERIE COMMERCIALI

SERIE COMMERCIALISERIE COMMERCIALI

SERIE COMMERCIALI

Our MI antipanic breakthrough series have been designed to be applied even on

sliding doors built with any type of adequately adapted commercial series.To this

purpose, the following pages contain the necessary measurements and/or notes

to plan and resize the doors.

Preliminary Notes:

- The preparation of the doorframes must allow the insertion of the hinge pins; it is

recommended that the faced and fixed cross members be mounted with U-bolts;

- Upper and lower hinging alignment must be axial.

- Pay attention to how the hinge elements are attached to the structure. They should be fixed

rigidly in order to avoid that with time vibrations and movement limit efficiency and make the

system unsafe for users;

- If the structure is not strong enough, the assembler must reinforce it.

- Upper and lower hinges must be aligned axially.

- Only in case of mobile doors, it is recommended that the glass be firmly set with silicone

sealant in addition to any other types of weather strip.

- Only stratified or tempered glass should be used.

MOBILE DOORS:

- Resize the length of the upright and cross sections according to the size of the sections

used- follow indications on pages 9÷13;

- Fasten the elements that make up the antipanic system for mobile doors.

- If necessary, insert the "wheel" device (art. P4173). See pg. 3.

ANTIPANIC BAR

- Cut sections PM339A and PM338A and chamfer and bore holes in section PM338A as

indicated on page 20.

- Apply the bar on the mobile door, mount the spiral cable and finish mounting the doors on the

Corsa or Rodeo beam, adapting the instructions for the S40 series on pages 21-23.

- Carry out the power connections and checks as indicated on page 24.

MAKE SURE THE BREAKTHROUGH SIDE IS THE CORRECT ONE AND THAT THE ANTIPANIC SYSTEM FOR

MOBILE DOORS IS COMPLETE BEFORE PERFORMING ANY MACHINING WORK!

- pg. 9 -

Vertical section with COMMERCIAL SERIESVertical section with COMMERCIAL SERIES

Vertical section with COMMERCIAL SERIES

127

169

151

13

80

M

H

Y

15

29

9

40

±6

C

43

INSIDE THE ROOM TO BE EVACUATED

LC00

151

13

80

M

H

Y

15

29

9

135

195

40

±6

D

43

LD00

MOUNTING FROM OUTSIDE THE ROOM TO BE EVACUATED

LEGEND

H= wall opening heigh

Y= Corsa/Rodeo beam fixing height:

with LC00 = H + 18*

with LD00 = H + 44*

M= sliding door height** = Y -108

C/D = Height under beam box = H

* these measurements allow net light continuity at the

passage between indoors and outdoors (H = C/D);

**Other specific dimensions are not provided for the

mobile door. Please refer to the door supplier's

documentation.

The use of LC00 or LD00 does not affect the choice of

mounting solution (inside or outside); even the Y fixing

height can be adapted to individual needs, as long as

the other formulas are also adapted.

BREAKTHROUGH

DIRECTION

INSIDE THE ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

MOUNTING FROM INSIDE THE ROOM TO BE EVACUATED

- pg. 10 -

L

Vsf

A

6

min

29 ±6

LC00

LD00

LEGEND

L= wall opening width

Vsf = Width of passage created with breakthrough

A* = Sliding door width

* Use MI6010 or MI6020 with A up to 1100;

use MI6110 or MI6120 with A up to 1500.

BREAKTHROUGH

DIRECTION

INDOOR ROOM TO BE AVACUATED

L

Vsf

A

LC00

LD00

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

BREAKTHROUGH

DIRECTION

MI6010 / MI6110

MI6020 / MI6120

Horizontal sections with the COMMERCIAL SERIESHorizontal sections with the COMMERCIAL SERIES

Horizontal sections with the COMMERCIAL SERIES

MOUNTING FROM INSIDE THE ROOM TO BE EVACUATED

- pg. 11 -

Horizontal sections with the COMMERCIAL SERIESHorizontal sections with the COMMERCIAL SERIES

Horizontal sections with the COMMERCIAL SERIES

LEGEND

L= wall opening witdth

Vsf = Width of passage created with breakthrough

A* = Sliding door width

* Use MI6010 or MI6020 with A up to 1100;

use MI6110 or MI6120 with A up to 1500.

L

Vsf

A

29 ±6

LC00

LD00

BREAKTHROUGH

DIRECTION

INDOOR ROOM TO BE AVACUATED

LC00

LD00

L

Vsf

A

BREAKTHROUGH

DIRECTION

BREAKTHROUGH

DIRECTION

INDOOR ROOM TO BE AVACUATED

MI6010 / MI6110

MI6020 / MI6120

MOUNTING FROM OUTSIDE THE ROOM TO BE EVACUATED

- pg. 12 -

22

80 25 85 80

50

70 69 69 200 max

25 56

11

190

COMMERCIAL SERIES mounting instructionsCOMMERCIAL SERIES mounting instructions

COMMERCIAL SERIES mounting instructions

Art. PM339A

Art. PM338A

Art. PM208

Art. PM207

Art. PM205

Art. PM306

Art. PM911A Art. PL593

Thickening and reinforcing

the frame to be sized and

positioned are care of the

constructor.

INSIDE MOUNTINGINSIDE MOUNTING

INSIDE MOUNTING

OUTSIDE MOUNTINGOUTSIDE MOUNTING

OUTSIDE MOUNTING

HINGING OF

MOBILE DOORS

69

*MAM002 is simply a finishing accessory

that may be replaced with any other type of

finish the constructor chooses, even if it

requires a larger section of the door's

upright.

Art. MAM002*

- pg. 13 -

COMMERCIAL SERIES mounting instructionsCOMMERCIAL SERIES mounting instructions

COMMERCIAL SERIES mounting instructions

200 max

10

Art. PM339A

Art. PM338A

Art. PM909

+PM910

+PM913

Art. P4117

When sizing sections PM339A and PM338A, pay attention to

the type of finish for the door in order to correctly align all

components.

- MOBIL DOORS-

FRONTAL MATCH

SLIDING WHEEL - OPTIONAL

Place the wheel at a sufficient distance so as to avoid contact with the

ground during the sliding door's opening, but not too far as this would hinder

easy rehooking.

9

60

83

143

5

1 ÷ 3

Art. P4173

WARNING!!!

Sliding surfaces presenting

irregularities or furrows affect the

proper operation of this element.

- pg. 14 -

This page left intentionally blank

- pg. 15 -

MI System

Applied to our section series

for S40

automatic sliding doors

The following two pages have only some application examples

with our sections; for a complete series of the construction

types, heights and construction parts for the creation of these

doorframes, please refer to the technical documentation of

the S40 series.

- pg. 16 -

L

65

53

Vsf

A

H

M15

13

80

LC00

LEGEND

H= wall opening height

L= wall opening width

Vsf = Width of passage created with breakthrough

M= sliding door height

A* = sliding door width

* Use MI6010 or MI6020 with A up to 1100;

use MI6110 or MI6120 with A up to 1500.

INDOOR ROOM TO BE AVACUATED

BREAKTHROUGH

DIRECTION

BREAKTHROUGH

DIRECTION INDOOR ROOM TO BE AVACUATED

S40 series - sectionsS40 series - sections

S40 series - sections

MOUNTING FROM INSIDE THE ROOM TO BE EVACUATED

- pg. 17 -

S40 series - sectionsS40 series - sections

S40 series - sections

Vsf

L

A

4

H

M15

44

80

LD00

LEGEND

H= wall opening height

L= wall opening width

Vsf = Width of passage created with breakthrough

M= Mobile door height

A* = Sliding door width

* Use MI6010 or MI6020 with A up to 1100;

use MI6110 or MI6120 with A up to 1500.

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

BREAKTHROUGH

DIRECTION INDOOR ROOM TO BE AVACUATED

BREAKTHROUGH

DIRECTION

MOUNTING FROM INSIDE THE ROOM TO BE EVACUATED

- pg. 18 -

53

81

A

80

H

M15

13

L =Vsf

S40 series - sectionsS40 series - sections

S40 series - sections

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

LC00

MOUNTING FROM OUTSIDE THE ROOM TO BE EVACUATED

LEGEND

H= wall opening height

L= wall opening width

Vsf = Width of passage created with breakthrough

M= Mobile door height

A* = Sliding door width

* Use MI6010 or MI6020 with A up to 1100;

use MI6110 or MI6120 with A up to 1500.

- pg. 19 -

S40 series - sectionsS40 series - sections

S40 series - sections

44

15 M

H

80

L = Vsf

A

LD00

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

BREAKTHROUGH

DIRECTION

BREAKTHROUGH

DIRECTION

INDOOR ROOM TO BE EVACUATED

MOUNTING FROM OUTSIDE THE ROOM TO BE EVACUATED

LEGEND

H= wall opening height

L= wall opening width

Vsf = Width of passage created with breakthrough

M= Mobile door height

A* = Sliding door width

* Use MI6010 or MI6020 with A up to 1100;

use MI6110 or MI6120 with A up to 1500.

- pg. 20 -

- Take out the PM339A (1)

and PM338A (2) upper and lower

hooking sections from the

package and remove the parts

inserted into them.

- Cut them to the proper

length using the indicated formu-

la.

- Correctly evaluate the

breakthrough side of the doors and

work the lower section (2) as in

the illustration **. .

** The illustration shows the

work that must be performed on

the left door. The right door will

require mirror-image work.

ANTIPANIC BAR machiningANTIPANIC BAR machining

ANTIPANIC BAR machining

DX

SX

45°

42

111

180

Wl + 50

1

2

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

INDOOR ROOM TO BE EVACUATED

BREAKTHROUGH

DIRECTION

2

bore a ∅7 hole with a 200 max pitch

Page is loading ...

CAME MI6010, MI6020, MI6110, MI6120 Installation guide

CAME MI6010, MI6020, MI6110, MI6120 Installation guide

Related papers

Other documents