2. Mocka
  3. Boston Contemporary Cot

Mocka Boston Contemporary Cot Assembly Instructions

  • Hello! I have reviewed the assembly instructions for the Boston Contemporary cot. This document provides a detailed guide on assembling the cot, including a list of supplied hardware, step-by-step instructions, safety tips, and information on recommended mattress size. I am ready to help you with any questions you may have regarding the cot assembly or its features.
  • What size mattress is recommended for this cot?
    What should I do before my child can sit up?
    How should i clean the cot?
WARNING: TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT
SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD
CAN SIT UP
Hardware Supplied
D E
Foot Pads
x 6
Allen Key
x 1
Bolt
x 4
Bolt
x 4
Bolt
x 8
Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power points.
Keep all medications, string, elastic, small toys or small items, such as money, out of reach from
any position in the cot.
Assembly
Care must be taken when attaching sides. Do not over-tighten screws as this can cause damage
to the cot.
Care and Maintenance
Regularly check all screws for tightness or damage that could render the cot unsafe.
To clean - use a damp cloth, avoiding the use of detergents or abrasives.
Recommended mattress size
This cot has been manufactured for use with a mattress which measures 1300mm long x 690mm
wide x 100mm in thickness. The width and length are specified because it is important that gaps
between the mattress and the sides and ends of the cot will not exceed 40mm. This is to minimize
the risk of a child’s limb becoming caught in the gap. The thickness of the mattress has been
specified to ensure that the depth of the cot is greater than 500mm with the mattress base in the
lower position to minimize the risk of a child climbing or falling out of the cot.
A
B
C
Boston Cot
Assembly Instructions
Thank you for your purchase.
Please follow the manufacturers assembly instructions
in detail to ensure the safety features of the cot are not
compromised.
1
mocka.co.nz | mocka.com.au | PO BOX 18, Pinkenba, QLD 4008
mocka.co.nz | mocka.com.au | PO BOX 18, Pinkenba, QLD 4008
12
Boston Cot
2
Assembly Instructions
Insert 4x screws (C) in the holes as shown. Tighten with the Allen key (D)
A
A
A
A
A
D
C
C
C
C
A
A
A
C
C
E
E
E
E
E
E
C
C
Attach 6 x foot pads(E) to panels [1] and [2]. Find one of the side panels
and attach to both end panels of the cot using 4x screws (A) in the holes
as shown. Insert 4x screws (C) in the
Allen key (D).
holes as shown. Tighten with the
A
A
D
1
2
mocka.co.nz | mocka.com.au | PO BOX 18, Pinkenba, QLD 4008
34
Boston Cot
3
Assembly Instructions
Turn the cot over so the bottom of cot is at the top.Attach the cot base to
the required level(newborn or Toddler) using 4 x screws(B) as shown
and tighten with allen key.Pictured is the lower toddler base.The higher
newborn level is closer to the top rail of the cot.
B
B
B
B
B
D
Slide the remaining side panel into place and attach using 4x screws
Turn the cot over so it is now upright.
(A) in the holes as shown. Tighten with the Allen key (D).
A
A
A
A
DA
mocka.co.nz | mocka.com.au | PO BOX 18, Pinkenba, QLD 4008
56
Boston Cot
4
Assembly Instructions
All done! Regularly check all screws are suitably tightened. Place the
correct size mattress into the cot before use. To clean use a damp
cloth, avoiding the use of detergents or abrasives. Once assembled lift
furniture into place, do not drag.
To adjust the base setting, remove the C screws from the end panels
and repeat steps 2 and 3 by removing the side panel and moving the
base to the corresponding hole. Securely attach again in the adjusted
position.
B
B
B
B
/