Eclipse 091009 Assembly Instruction Manual

Brand: Eclipse

Model: 091009

Type: Assembly Instruction Manual

ECLIPSE

Cot Model # 091009

IMPORTANT:

RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

Due to variations in the style and design of our products, the photographs and illustrations

shown in this instruction manual are generic, therefore product fabrics, colour and

design may vary from images shown. CNP Brands reserves the right to alter product

specications without notice as a result of our ongoing policy of product improvement.

Contents

Assembly contents list

Assembly / Operating instructions

How to care for your Childcare Cot

Congratulations on your purchase of the

Childcare Eclipse Cot.

This product has been designed and developed with

safety, comfort and functionality in mind. Please take

the time to read this manual carefully before using

this product and keep it in a safe place for future

reference.

Read all instructions before assembly and use of the cot. Keep

instructions for future use. Follow the manufacturer’s assembly

instructions to ensure the safety features of the cot are not

compromised.

Safety Precautions

This cot has been manufactured for one child only, with a maximum weight of 18kgs in cot

conguration.

When the mattress base is assembled in the lower position, ensure the higher cot base holes are

covered tightly with the lling bolts supplied. This is to prevent nger entrapment, swallowing and

inhalation hazards.

Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power points.

Ensure the cot is completely assembled and check that all parts are securely tightened before

placing the child into the cot.

Ensure medication, string, elastic, small toys or small items such as money etc are always kept out

of the child’s reach when in the cot.

Do not over tighten bolts/screws.

Ensure that the child is clear of any moving parts when adjusting the cot.

RECOMMENDED MATTRESS SIZE:

THIS COT HAS BEEN MANUFACTURED FOR USE WITH A MATTRESS WHICH MEASURES 690

MM WIDE BY 1300 MM LONG AND 100 MM-150 MM IN THICKNESS. The width and length are

specied because it is important that the gaps between the mattress and the sides and ends of the

cot will not exceed 40 mm when the mattress is pushed to one side or end, and 20mm when the

mattress is centred in the cot. This is to minimise the risk of a child’s limb becoming caught in the

gap. The thickness of the mattress has been specied to ensure that the depth of the cot is greater

than 500 mm with the mattress base in the lower position to minimise the risk of a child climbing or

falling out of the cot.

WARNING

: TO PREVENT FALLS, THE MATTRESS

BASE OF THIS COT SHOULD BE ADJUSTED TO THE

LOWEST POSITION BEFORE THE CHILD CAN SIT UP.

RECOMMENDED MATTRESS SIZE:

690 MM WIDE X 1300 MM LONG X 100 MM-150 MM THICK.

Assembly ContentsAssembly Contents

Check what you have received...

You have received 1 box. Please check the contents of the box against the list below.

If anything is missing, please contact Customer Service. In Australia, contact CNP

Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution on

0800 567 5000.

Supplied loose in box:

End panel

Side panel

Mattress base

Feet

60mm bolt

(Assembly bolt for side - end panels)

25mm bolt

(For bottom feet assembly)

35mm bolt

(For mattress base assembly)

Filling bolt & nut (pre-assembled)

Allen Key

Assembly Kit:

Assembly / Operating Instructions

Cot mode

HELPFUL HINTS

It is advisable that two people assemble the cot in the room in which it is to be used.

As small parts are involved in assembly, children should be kept clear of the assembly area.

Dispose of all packaging material immediately after the cot is assembled. Identify all parts and

components. Clear an area on the oor for assembly and place a sheet on the oor to ensure

the cot is not scratched during assembly.

Mattress base height

Use four cot assembly bolts provided to adjust mattress base height.

1. Mattress base in high position;

This is for use when your baby is young and cannot sit up

unaided.

2. Mattress base in low position;

This is the normal position for an active baby which can sit up

unaided.

PLEASE NOTE:

THE COT COMES WITH FILLING BOLTS ALREADY LOCATED IN THE LOWER HOLES OF

THE END PANELS. IF CHANGING THE MATTRESS BASE FROM THE UPPER TO THE LOWER

POSITION, YOU MUST SWAP OVER THE FILLING BOLTS. IT IS IMPORTANT THAT THE FILLING

BOLTS ARE REPLACED INTO THE OPEN HOLES. ENSURE THEY ARE SECURED TIGHTLY

WITH THE ALLEN KEY AND CHECK REGULARLY THAT THEY DO NOT LOOSEN.

Assembly / Operating Instructions

To attach side and end panels

1. Place the side panel into the groove created by the end panels.

Please ensure the counter sunk on end panels are facing

outside.

2. Using four 60mm bolts x the side panels to the end panels as

shown.

3. Repeat for the other side panel.

4. Now that the side panels is in place. Tighten all bolts on the end

and side panels.

Assembly / Operating Instructions

1. To attach the mattress base in the low position.

3. Locate and hand fasten all four 35mm cot bolts loosely.

4. Once all four bolts are located begin tightening them.

2. Place mattress base inside the cot frame. Secure the mattress

base as outlined below.

Warning: Do not over tighten the bolts. Over tightening bolts

may cause panels to crack.

2. Transfer all four lling bolts to the high position holes from the

low position holes.

3. It is easier to assemble the mattress base if you place the cot on

it’s side.

4. Secure the mattress base as outlined above.

Assembly / Operating Instructions

To attach mattress base - High Conﬁguration

Warning: Do not over tighten the bolts. Over tightening bolts

may cause panels to crack.

To attach mattress base - Low Conﬁguration

1. To attach the mattress base in the high position.

1110

Assembly / Operating Instructions

Assembling bottom feet

1. Line up the four feet holes with the base frame holes. Ensure the

at surface of the base frame is on the contact side of the foot

and the feet are facing outward.

2. Turn the cot upside down. Secure the foot to the base frame

using four 25mm bolts.

3. Repeat the steps above in order to assemble all four feet to the

base frame.

Warning: Do not over tighten the bolts. Over tightening bolts

may cause panels to crack.

The cot is now ready for use.

4. Check and ensure that all four feet are properly tightened to the

base frame before continuing the assembly process.

Assembly / Operating Instructions

Cleaning

To ensure the long-lasting use of your cot, wipe down with a damp cloth and use a mild soap

solution if necessary. Do not use abrasive cleaners. Always store product in a clean dry place.

Maintenance

Always check parts regularly for tightness of bolts, nuts and other fasteners – tighten or

replace if required. To maintain the safety of your cot, seek prompt repairs for bent, torn, worn

or broken parts. Use only those parts and accessories approved by CNP Brands.

If the drop-side panel does not slide down smoothly, use a silicon based spray; ensuring it

penetrates the mechanism sufciently.

If you have any difculties in assembling the cot, please contact our Service Department.

In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse

Distribution on 0800 567 5000.

Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030

Customer Service 1300 667 137 www.cnpbrands.com.au

Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St,

Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand

Customer Service: 0800 567 5000 [email protected]

Eclipse 091009 Assembly Instruction Manual

Eclipse 091009 Assembly Instruction Manual

Eclipse 091009 Assembly Instruction Manual

Other documents