Feature Highlights:
■ Reversible seat conguration.
■ Seat capacity is 250 pounds.
■ Grab bar is designed and tested to
meet ADA standards.
■ Reversible slat seat only (HC-117)
Reversible Shower Slat Seat
HC-1, HC-2 & HC-117
Folding Slat Seat with Grab Bar
Installation Instructions
Grab Bar Construction
Tubing
■ Stainless steel contruction.
■ Exposed surfaces in satin nickel
nish.
Snap-On Flange
■ 3" diameter ange furnished with
3 stainless steel screws. 2 of 3
screws provided must be used when
mounting bar to wall.
■ Flanges and center posts are heliarc
welded to tubing.
Shower Seat Operation
■ Shower seat folds up when not in
use.
■Warning: to avoid damaging or
pulling seat out of the wall, sit down
gently. Do not drop down on seat
suddenly.
Compliance:
■ Americans with Disabilities Act
(ADA)
Warranty:
Limited Lifetime - to the original end
purchaser in consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty
for complete warranty information.
Grab Bar Installation
■ Secure to wall with three mounting
ends.
■ For installation on stud wall, steel or
berglass construction use in wall
backing at all fastener locations to
comply with local building codes.
■ For installation on solid walls, use
expansion anchors and screws in
compliance with local building
codes.
Note: Fasteners are not provided by
Symmons.
■ Clearance is the distance between the
nished wall surface and the inner
edge of the tubing. e standard
clearance furnished is 1-1/2"
(38mm).
■ Dimensions are measured from
centerline of tubing to wall, unless
otherwise noted.
For California Residents
WARNING: is product contains
chemicals known to the State of California
to cause cancer, birth defects, or other
reproductive harm.
Snap-on ange
1 1/2" (38mm)
1 1/2" (38mm)
(38mm) diameter tube
1-1/2"
Shower Seat Blocking
■ Install on stud walls or steel
construction using in wall backing at
all fastener locations to comply with
local building codes.
■ Fasteners supplied with seat must be
installed properly. Center on studs so
as to fully engage material.
■ Install fasteners with a minimum
of 2" from any edge of support
blocking.
Shower Seat Installation
■ Secure unit to the wall with two
mounting anges (3 fasteners each) at
top and the baseplate/guide bracket
below (4 fasteners).
■ Bottom of support tube must be
positioned within the baseplate and
guide bracket before they are secured
to wall.
■ Reversing Top - Remove four acorn
nuts and carriage bolts, rotate seat
end for end, and replace bolts and
nuts.
Dimensions Reversible Shower Seat, HC-1 & HC-2
Note: Design and Dimensions subject to change without notice.
7 1/4"
185mm
9 3/8"
240mm
2 1/4"
55mm
Dia.
Bolt Circle
4 1/2"
115mm
6 3/4"
170mm
2 1/4"
55mm
19 1/2"
495mm
22 1/4"
565mm
20 15/16"
530mm
1 3/8"
35mm
36"
914mm
seat wall
33"
840mm
13 3/8"
340mm
Top view Back view
base plate
support tube
mounting ange
17" – 19"
432mm – 483mm
33" – 36"
838mm – 914mm
33" illustrated
38"
965mm
control area
within 15" of
48"
1219mm
Dimensions Grab Bar for Reversible Shower Seat HC-1 & HC-2
Note: Design and Dimensions subject to change without notice.
32-1/4"
819 mm
20-1/4"
514 mm
8-1/4"
210 mm
Top view Front view
guide bracket
36"
914 mm
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
/
