Symmons HC-1 Installation guide

Symmons
Brand
Symmons
Model
HC-1
Category
Wall & ceiling mounts accessories
Type
Installation guide

This manual is also suitable for

Symmons HC-1 is a reversible shower seat with a grab bar that provides a safe and comfortable showering experience. It has a 250-pound capacity and is ADA-compliant. It installs easily on stud walls or steel construction using in-wall backing at all fastener locations. The grab bar meets ADA standards and has a 1-1/2" clearance from the finished wall surface. The seat folds up when not in use and can be installed with the seat on either the left or right side.

Symmons HC-1 is a reversible shower seat with a grab bar that provides a safe and comfortable showering experience. It has a 250-pound capacity and is ADA-compliant. It installs easily on stud walls or steel construction using in-wall backing at all fastener locations. The grab bar meets ADA standards and has a 1-1/2" clearance from the finished wall surface. The seat folds up when not in use and can be installed with the seat on either the left or right side.

Feature Highlights:
■ Reversible seat conguration.
■ Seat capacity is 250 pounds.
■ Grab bar is designed and tested to
meet ADA standards.
■ Reversible slat seat only (HC-117)
Reversible Shower Slat Seat
HC-1, HC-2 & HC-117
Folding Slat Seat with Grab Bar
Installation Instructions
Grab Bar Construction
Tubing
■ Stainless steel contruction.
■ Exposed surfaces in satin nickel
nish.
Snap-On Flange
■ 3" diameter ange furnished with
3 stainless steel screws. 2 of 3
screws provided must be used when
mounting bar to wall.
■ Flanges and center posts are heliarc
welded to tubing.
Shower Seat Operation
■ Shower seat folds up when not in
use.
■Warning: to avoid damaging or
pulling seat out of the wall, sit down
gently. Do not drop down on seat
suddenly.
Compliance:
■ Americans with Disabilities Act
(ADA)
Warranty:
Limited Lifetime - to the original end
purchaser in consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty
for complete warranty information.
Grab Bar Installation
■ Secure to wall with three mounting
ends.
■ For installation on stud wall, steel or
berglass construction use in wall
backing at all fastener locations to
comply with local building codes.
■ For installation on solid walls, use
expansion anchors and screws in
compliance with local building
codes.
Note: Fasteners are not provided by
Symmons.
■ Clearance is the distance between the
nished wall surface and the inner
edge of the tubing. e standard
clearance furnished is 1-1/2"
(38mm).
■ Dimensions are measured from
centerline of tubing to wall, unless
otherwise noted.
For California Residents
WARNING: is product contains
chemicals known to the State of California
to cause cancer, birth defects, or other
reproductive harm.
Snap-on ange
1 1/2" (38mm)
1 1/2" (38mm)
(38mm) diameter tube
1-1/2"
Shower Seat Blocking
■ Install on stud walls or steel
construction using in wall backing at
all fastener locations to comply with
local building codes.
■ Fasteners supplied with seat must be
installed properly. Center on studs so
as to fully engage material.
■ Install fasteners with a minimum
of 2" from any edge of support
blocking.
Shower Seat Installation
■ Secure unit to the wall with two
mounting anges (3 fasteners each) at
top and the baseplate/guide bracket
below (4 fasteners).
■ Bottom of support tube must be
positioned within the baseplate and
guide bracket before they are secured
to wall.
■ Reversing Top - Remove four acorn
nuts and carriage bolts, rotate seat
end for end, and replace bolts and
nuts.
Dimensions Reversible Shower Seat, HC-1 & HC-2
Note: Design and Dimensions subject to change without notice.
7 1/4"
185mm
9 3/8"
240mm
2 1/4"
55mm
Dia.
Bolt Circle
4 1/2"
115mm
6 3/4"
170mm
2 1/4"
55mm
19 1/2"
495mm
22 1/4"
565mm
20 15/16"
530mm
1 3/8"
35mm
36"
914mm
seat wall
33"
840mm
13 3/8"
340mm
Top view Back view
base plate
support tube
mounting ange
17" – 19"
432mm – 483mm
33" – 36"
838mm – 914mm
33" illustrated
38"
965mm
control area
within 15" of
48"
1219mm
Dimensions Grab Bar for Reversible Shower Seat HC-1 & HC-2
Note: Design and Dimensions subject to change without notice.
32-1/4"
819 mm
20-1/4"
514 mm
8-1/4"
210 mm
Top view Front view
guide bracket
36"
914 mm
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2018 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-413 REV C ■ 021618
  • Page 1 1
  • Page 2 2

Symmons HC-1 Installation guide

Symmons
Brand
Symmons
Model
HC-1
Category
Wall & ceiling mounts accessories
Type
Installation guide
This manual is also suitable for

Symmons HC-1 is a reversible shower seat with a grab bar that provides a safe and comfortable showering experience. It has a 250-pound capacity and is ADA-compliant. It installs easily on stud walls or steel construction using in-wall backing at all fastener locations. The grab bar meets ADA standards and has a 1-1/2" clearance from the finished wall surface. The seat folds up when not in use and can be installed with the seat on either the left or right side.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents