FLEXCO Manual Roller Lacer Operating instructions

Type
Operating instructions

FLEXCO Manual Roller Lacer is a versatile tool that can be used for a variety of lacing applications. With its ability to handle both 2-layer and 3-layer face strips, this lacer is perfect for a wide range of projects. The quick and easy conversion process allows you to switch between face strips in a matter of minutes, giving you the flexibility to tackle any job that comes your way.

The FLEXCO Manual Roller Lacer is also incredibly durable, with a heavy-duty construction that can withstand even the toughest conditions. The precision-machined components ensure smooth operation and accurate lacing, making it the perfect tool for professionals and DIYers alike.

FLEXCO Manual Roller Lacer is a versatile tool that can be used for a variety of lacing applications. With its ability to handle both 2-layer and 3-layer face strips, this lacer is perfect for a wide range of projects. The quick and easy conversion process allows you to switch between face strips in a matter of minutes, giving you the flexibility to tackle any job that comes your way.

The FLEXCO Manual Roller Lacer is also incredibly durable, with a heavy-duty construction that can withstand even the toughest conditions. The precision-machined components ensure smooth operation and accurate lacing, making it the perfect tool for professionals and DIYers alike.

It is recommended that you follow these steps when converting lacers with serial numbers 3500-59999 if you will be using the 3- layer
face strip exclusively. If both the 3-layer and 2-layer face strips will be used, you may use the 3- layer Face Strip with the Locking
Lever(s) and Backup Bar Assembly in place but not engaged. Both of the Face Strip Retaining Latches will need to be installed.
Converting the Manual Roller Lacer®
to accept the 3-Layer Face Strip
(Serial Numbers 3500 - 59999)
UNLOCKED
LOCKED
1. Make sure Locking Levers are in
the unlocked/upright position.
2. Remove the 2-layer Face Strip by
rst loosening the thumb screw or
slotted style screw and then sliding
the Face Strip out through either
end of the lacer.
3. Remove the rst End Plates by starting at
one end of the lacer and removing the 12
self-tapping machine screws that secure the
End Plate to the extruded components of
the Roller Lacer. The 24” Roller Lacer and
the Microlacer only have one Locking Lever.
Remove the End Plate from this side. A
gentle pull or slight tap with a hammer may
be needed to free the End Plate from the
spring pin stop for the Locking Lever.
4. Remove and discard the Locking
Lever Assembly.
5. Remove and discard the Backup Bar
Assembly located in the Extruded
Body.
6. Locate the two Face Strip Retaining Latches
included with the Face Strip Kit.
HOOK END
FACE STRIP
RETAINING
LATCH
7. Reattach the End Plate. Be sure not to over-
torque the self-tapping machine screws
when tightening.
a. Install one of the Face Strip Retaining
Latches so that the Lacer Pin clearance
notch faces towards the Face Strip. The
hook end of the Face Strip Retaining
Latch should be located at the top. Insert
spacer sleeve and screw through hole in
other end of latch. See Fig. 6.
b. Tighten the screws making sure not to
over-torque them.
8. For 36", 48" and 60" Roller Lacers repeat
Steps 3 through 8 for opposite side.
9. Install the new 3-Layer Face Strip into the Extruded Body.
a. Loosen the top screw securing the Face Strip Retaining Latch and
pivot the latch towards the back of the lacer. See Fig. 9a.
b. Insert the Face Strip all the way into the Extruded Body.
c. Pivot the Face Strip Retaining Latch back into position. See Fig. 9b.
d. Tighten the top screw.
CLEARANCE
NOTCH
Fig. 6
Fig. 5
Fig. 4
Fig. 1 Fig. 3
Fig. 2
Fig. 9a Fig. 9b
INSERT FACE STRIP
PIVOT LATCH BACK
INTO POSITION,
TIGHTEN SCREW
REMOVE 12
SCREWS
ENDPLATE
INSERT SPACER
SLEEVE AND SCREW
THRU HOLE IN LATCH
LOOSEN SCREW,
PIVOT LATCH
TOWARD BACK
OF LACER
2525 Wisconsin Avenue • Downers Grove, IL 60515-4200 • USA
Tel: (630) 971-0150 • Fax: (630) 971-1180 • E-mail: info@flexco.com
Visit www.flexco.com for other Flexco locations and products.
©2021 Flexible Steel Lacing Company. 11/16/21. For reorder: X1457
Patents: www.flexco.com/patents
  • Page 1 1

FLEXCO Manual Roller Lacer Operating instructions

Type
Operating instructions

FLEXCO Manual Roller Lacer is a versatile tool that can be used for a variety of lacing applications. With its ability to handle both 2-layer and 3-layer face strips, this lacer is perfect for a wide range of projects. The quick and easy conversion process allows you to switch between face strips in a matter of minutes, giving you the flexibility to tackle any job that comes your way.

The FLEXCO Manual Roller Lacer is also incredibly durable, with a heavy-duty construction that can withstand even the toughest conditions. The precision-machined components ensure smooth operation and accurate lacing, making it the perfect tool for professionals and DIYers alike.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI