Thor DRM1050 Installation guide

Thor
Brand
Thor
Model
DRM1050
Type
Installation guide

Below you will find brief information for DRM1050, DRM750, DRM95-20A. This guide provides connection instructions for Thor Technologies Ripple Filters DRM1050 & DRM750 and an example of how to connect them in series with a DRM95-20A Mains Filtered Surge Protection product. It emphasizes the importance of using a totally isolated neutral output and proper wiring by a licensed electrician, adhering to local regulations. The guide also covers maximum current limits and highlights the need for independent, isolated circuits to prevent overheating and product failure.

Below you will find brief information for DRM1050, DRM750, DRM95-20A. This guide provides connection instructions for Thor Technologies Ripple Filters DRM1050 & DRM750 and an example of how to connect them in series with a DRM95-20A Mains Filtered Surge Protection product. It emphasizes the importance of using a totally isolated neutral output and proper wiring by a licensed electrician, adhering to local regulations. The guide also covers maximum current limits and highlights the need for independent, isolated circuits to prevent overheating and product failure.

HARD WIRE PRODUCT INSTALLATION GUIDE FOR DRM1050 AND DRM750 RIPPLE FILTER
INCLUDING AN EXAMPLE OF INSTALLATION IN SERIES WITH A DRM95-20A.
DISCLAIMER:
This guide has been compiled as a connection guide only for Thor Technologies Ripple Filter
DRM1050 & DRM750. In addition, and as an option, if it is wired in Series with Thor Technologies
Mains Filtered Surge Protection product DRM95-20A, an example of how to connect is outlined.
It is not a guide or instruction for the configuration/orientation of a switchboard or any of the
fittings used therein.
The important parts are highlighted in the wiring diagrams for the Thor Technologies DRM1050 &
DRM750 and if a DRM95-20A is used.
Each CB*/RCD*/RCBO has some variations as to the wiring. Please read the instructions of the safety
device before installing with a DRM1050 or DRM750 and a DRM95-20A. The maximum current
allowable for the safety device to be used is 10A as the Ripple Filter Maximum current load is 10A.
All wiring must be carried out by a licensed electrician and all work is subject to regulations in each
state or territory.
Special instructions for all Thor Technologies hardware products:
The neutral connection output from the Thor Technologies hardware product like the Ripple Filter or
DRM95-20A must be used as a totally isolated neutral out for the circuit being protected/filtered
output.
Do not return the Neutral out from the Ripple Filters or from the DRM95-20A to the common Neutral
Bar in the switchboard or cross wire into existing circuits where that circuit’s neutral is returned to
the common neutral bar at the switchboard. Doing so will cause the product to overheat and
subsequently fail. If wired incorrectly with continuous current draw it may cause the casing to melt
or lead to other major problems.
Installer created or existing problems are not covered by Thor Technologies product warranties
written, implied or otherwise.
THE Ripple Filter Circuit and the DRM95-20A circuit if used should be totally independent and
isolated.
All drawings subject to change without notice.
*shown on diagram
WIRING EXAMPLE OF SWITCHBOARD USING AN RCD AND DRM1050/DRM750
10A RCD Note: No Earth connection required. Outputs use Earth bar
Recommended 10A max per circuit. Not per Outlet.
Subject to Regulations
Guide only for DRM1050/DRM750. All wiring subject to Regulations in each State and Territory.
Cable used must meet 10A Standards and must use 10A RCD as Ripple Filter 10A max.
WIRING EXAMPLE OF SWITCHBOARD USING AN RCD AND THOR’S MAINS FILTERED
DRM9520A IN SERIES WITH DRM1050/DRM750 RIPPLE FILTER
10A RCD Note: Earth connection required DRM95 20A Input only.
Recommended For Output connections always use Earth Bar.
Subject to Regulations
Guide only for DRM1050/DRM750. All wiring subject to Regulations in each State and Territory.
Cable used must meet 10A Standards and must use 10A RCD as Ripple Filter 10A max.
Must be fully isolated.
Connect only from
Ripple Filter out to the
circuit
To LED
circuit
  • Page 1 1
  • Page 2 2

Thor DRM1050 Installation guide

Thor
Brand
Thor
Model
DRM1050
Type
Installation guide

Below you will find brief information for DRM1050, DRM750, DRM95-20A. This guide provides connection instructions for Thor Technologies Ripple Filters DRM1050 & DRM750 and an example of how to connect them in series with a DRM95-20A Mains Filtered Surge Protection product. It emphasizes the importance of using a totally isolated neutral output and proper wiring by a licensed electrician, adhering to local regulations. The guide also covers maximum current limits and highlights the need for independent, isolated circuits to prevent overheating and product failure.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents