TRX 433MHz Operating instructions

433MHz
Brand
TRX
Model
433MHz
Category
Motion detectors
Type
Operating instructions

TRX 433MHz is a wireless pet-friendly passive infrared motion sensor designed for home security systems. It detects movement up to 12 meters away and features selectable LED indicators, a tamper switch for added security, and a long battery life of up to 5 years. The device is compatible with Freelink Supervised alarm systems and requires a TRX Transceiver for pairing. Installation is simple, with adjustable mounting height from 1.5 to 2.4 meters.

TRX 433MHz is a wireless pet-friendly passive infrared motion sensor designed for home security systems. It detects movement up to 12 meters away and features selectable LED indicators, a tamper switch for added security, and a long battery life of up to 5 years. The device is compatible with Freelink Supervised alarm systems and requires a TRX Transceiver for pairing. Installation is simple, with adjustable mounting height from 1.5 to 2.4 meters.

TRX PIR
Wireless Pet Friendly Passive Infrared Motion Sensor
Specifications:
Detection Method Passive Infrared
Coverage 12m x 12m @85˚
Frequency 917.1 to 921.3MHz
Mounting Height 1.5m to 2.4m
LED Indicator On/Off Selectable
Tamper Switch Front Cover Micro Switch
Battery Type 1 x CR123A/CR17335
Battery Life Up to 5 Years
Operating Temperature -20˚C to 50˚C
Environment Humidity 85% max.
Pet Immunity Small Animals 0-40cm High
Radio Device Protocol Freelink Supervised
Compatible Systems ESL, ESL-2, Elite-S, Runner
Requires TRX TRANSCEIVER
Hardware & Mounting
Detection Area
Pairing and Jumper Options
Movement Indicator LED:
Jumper ON = LED ON
Jumper OFF = LED OFF
Walk Test Mode (For testing purposes only, Install in Normal position)
Walk Test = Sends alarm triggers with every motion detection
Normal = Sends alarm trigger & will not generate another for 2mins
Pulse Count
2 = Normal conditions
4 = Hash conditions (makes detector less responsive)
TRX PIR
Pairing Button
Pairing LED
Programming
1. Insert Battery into TRX PIR
2. Connect the TRX Transceiver to Alarm panel
3. Press the Red Pairing Button on the TRX PIR until the Red Pairing LED starts flashing
4. Now press the Pairing button on the TRX Transceiver until the blue LED starts flashing
5. The Red Pairing LED should stop flashing to indicate dice is paired successfully
6. Enter programming mode on the Alarm panel (P 000000 E default installer code)
7. Press PROG 122 ENTER then the input number you wish to make wireless, followed by ENTER,
Next make sure options 1 & 5 are ON and ENTER, this makes the input active and wireless
8. Press PROG 164 ENTER then the input number you wish to enrol the device into and ENTER
9. Press ENTER again to start learning, the keypad will start beeping to indicate it’s searching
10. Activate the TRX PIR Tamper switch, the beeping should stop, indicating device is learnt
Tamper Switch
Testing
1. Once programming is complete, Fit the TRX PIR in place on the wall
2. Enter programming mode on the Alarm panel (P 000000 E default installer code)
3. Press PROG 200 Enter, 6 ENTER, ENTER (keypad will beep & WALK will come up on the display)
4. Leave the room with the detector in it undisturbed for at least 2 minutes.
5. After 2 minutes walk into the room and into the detection zone.
6. The keypads display will then indicate all the inputs that have been triggered.
These triggers will remain on the display until you exit the Walk test mode.
7. Exit programming mode.
ARROWHEAD ALARM PRODUCTS Ltd.
344b Rosedale Rd,
Albany,
Auckland.
Ph. 09 414 0085
Fax. 09 414 0088
www.aap.co.nz
v2.0
  • Page 1 1
  • Page 2 2

TRX 433MHz Operating instructions

433MHz
Brand
TRX
Model
433MHz
Category
Motion detectors
Type
Operating instructions

TRX 433MHz is a wireless pet-friendly passive infrared motion sensor designed for home security systems. It detects movement up to 12 meters away and features selectable LED indicators, a tamper switch for added security, and a long battery life of up to 5 years. The device is compatible with Freelink Supervised alarm systems and requires a TRX Transceiver for pairing. Installation is simple, with adjustable mounting height from 1.5 to 2.4 meters.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents