ESAB Gouging Shield Assembly Assembly Instruction
- Type
- Assembly Instruction
ESAB Gouging Shield Assembly is a 2-piece shield designed for use with the PT-121 torch. It replaces the standard heat shield for gouging applications. Its capabilities include:
- Compatible with PT-121 torch for gouging.
- User-friendly assembly by twisting motion until the O-ring engages the internal groove.
- Enhanced safety and protection from sparks and debris during gouging.
- Detailed operating instructions available in the PT-121 torch booklet (F-12-794) and "Plasmarc Gouging Guide" (F-7080).
ESAB Gouging Shield Assembly is a 2-piece shield designed for use with the PT-121 torch. It replaces the standard heat shield for gouging applications. Its capabilities include:
- Compatible with PT-121 torch for gouging.
- User-friendly assembly by twisting motion until the O-ring engages the internal groove.
- Enhanced safety and protection from sparks and debris during gouging.
- Detailed operating instructions available in the PT-121 torch booklet (F-12-794) and "Plasmarc Gouging Guide" (F-7080).
F-14-480
June, 1996
ESAB Welding & Cutting Products
PO Box 100545, SC 29501-0545
F-14-480 6/96 1M Printed in U.S.A.
This 2-piece gouging shield assembly is designed for
use with the PT-121 torch. It is used in place of a stan-
dard heat shield for gouging applications. For operat-
ing details on gouging refer to the booklet covering the
PT-121 torch, F-12-794 or “Plasmarc Gouging Guide”,
F-7080, which is packed with each PCM-150 power
source. The guide is also available from any ESAB dis-
tributor.
GOUGING SHIELD ASSEMBLY
P/N 20378
O-RING- 994092
(lubricate with silicone grease)
SHIELD -
20380
Assemble shield to this
end of adaptor.
ADAPTOR-
20379
Push shield into
adaptor with a
twisting motion
until first O-ring
engages internal
groove of adaptor.
F-14-480
June, 1996
ESAB Welding & Cutting Products
PO Box 100545, SC 29501-0545
F-14-480 6/96 1M Printed in U.S.A.
This 2-piece gouging shield assembly is designed for
use with the PT-121 torch. It is used in place of a stan-
dard heat shield for gouging applications. For operat-
ing details on gouging refer to the booklet covering the
PT-121 torch, F-12-794 or “Plasmarc Gouging Guide”,
F-7080, which is packed with each PCM-150 power
source. The guide is also available from any ESAB dis-
tributor.
GOUGING SHIELD ASSEMBLY
P/N 20378
O-RING- 994092
(lubricate with silicone grease)
SHIELD -
20380
Assemble shield to this
end of adaptor.
ADAPTOR-
20379
Push shield into
adaptor with a
twisting motion
until first O-ring
engages internal
groove of adaptor.
F-14-480
June, 1996
ESAB Welding & Cutting Products
PO Box 100545, SC 29501-0545
F-14-480 6/96 1M Printed in U.S.A.
This 2-piece gouging shield assembly is designed for
use with the PT-121 torch. It is used in place of a stan-
dard heat shield for gouging applications. For operat-
ing details on gouging refer to the booklet covering the
PT-121 torch, F-12-794 or “Plasmarc Gouging Guide”,
F-7080, which is packed with each PCM-150 power
source. The guide is also available from any ESAB dis-
tributor.
GOUGING SHIELD ASSEMBLY
P/N 20378
O-RING- 994092
(lubricate with silicone grease)
SHIELD -
20380
Assemble shield to this
end of adaptor.
ADAPTOR-
20379
Push shield into
adaptor with a
twisting motion
until first O-ring
engages internal
groove of adaptor.
F-14-480
June, 1996
ESAB Welding & Cutting Products
PO Box 100545, SC 29501-0545
F-14-480 6/96 1M Printed in U.S.A.
This 2-piece gouging shield assembly is designed for
use with the PT-121 torch. It is used in place of a stan-
dard heat shield for gouging applications. For operat-
ing details on gouging refer to the booklet covering the
PT-121 torch, F-12-794 or “Plasmarc Gouging Guide”,
F-7080, which is packed with each PCM-150 power
source. The guide is also available from any ESAB dis-
tributor.
GOUGING SHIELD ASSEMBLY
P/N 20378
O-RING- 994092
(lubricate with silicone grease)
SHIELD -
20380
Assemble shield to this
end of adaptor.
ADAPTOR-
20379
Push shield into
adaptor with a
twisting motion
until first O-ring
engages internal
groove of adaptor.
-
1
ESAB Gouging Shield Assembly Assembly Instruction
- Type
- Assembly Instruction
ESAB Gouging Shield Assembly is a 2-piece shield designed for use with the PT-121 torch. It replaces the standard heat shield for gouging applications. Its capabilities include:
- Compatible with PT-121 torch for gouging.
- User-friendly assembly by twisting motion until the O-ring engages the internal groove.
- Enhanced safety and protection from sparks and debris during gouging.
- Detailed operating instructions available in the PT-121 torch booklet (F-12-794) and "Plasmarc Gouging Guide" (F-7080).
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ESAB PT-19XL Mechanized Plasmarc Cutting Torch Troubleshooting instruction
-
-
-
-
-
ESAB ESP-150 User manual
-
-
-
-