Nice Apollo EDSWG/A Wireless Era Digital Keypad Quick start guide

Brand: Nice Apollo

Model: EDSWG/A Wireless Era Digital Keypad

Type: Quick start guide

Nice Apollo EDSWG/A Wireless Era Digital Keypad

The Nice Apollo EDSWG/A Wireless Era Digital Keypad is a wireless keypad that can be used to control your gate or garage door opener. It features three channel buttons that can be programmed to different codes, allowing you to open and close your gate or garage door from multiple locations. The keypad also has a built-in 10-digit LED display that shows the code that is being entered, as well as the status of the gate or garage door.

Here are some of the features and possible use cases of the Nice Apollo EDSWG/A Wireless Era Digital Keypad:

Nice Apollo EDSWG/A Wireless Era Digital Keypad

Here are some of the features and possible use cases of the Nice Apollo EDSWG/A Wireless Era Digital Keypad:

EDSWG/A Quickstart Guide

Technical Bulletin

TB16060102

Publish Date:

June 8, 2016

The EDSWG Wireless Keypad will only work with NICE radio receivers.

FACTORY CODES:

Channel button A is 1 1

Channel button B is 2 2

Channel button C is 3 3

TRANSMITTING:

Press the code, then the channel button

*Example: 1 1 A will transmit on channel A

*Note: The same code can be programmed for each channel.

*Note: The keypad will transmit as long as the channel button is held down.

MODE 1 RECEIVER PROGRAMMING:

Mode 1 = Button A is receiver channel 1, button B is receiver channel 2 and button C is receiver channel 3

OXI/A

i. Press and hold the learn button on the OXI/A receiver until the light comes on solid

and release

ii. On the keypad, press 1 1 and then hold A until the receiver light goes out

iii. Programming is complete for buttons A, B and C

318N (only buttons A and B will function)

i. Press and release the learn button on the 318N receiver

ii. Immediately after releasing the learn button, on the keypad press 1 1 and then hold

A until the receiver light goes out

iii. Release A and immediately press A again until the light on the receiver come

s back

and flashes

iv. Programming is complete for all buttons A and B

CHANGING CODES:

Codes are configurable from 1 to 8 digits in length

STORE CODES IN A SAFE PLACE ! Resetting to default can only be done at the factory.

i. Press and hold 0

ii. While holding 0, press and release A

iii. Release 0

iv. Press the exsiting code

v. Press A

vi. Press the new code

vii. Press A

viii. Press the new code

ix. Press A

*Note: The same procedure is used to program all channel buttons

TO USE THE KEYPAD WITHOUT A CODE:

This allows the keypad to work as a simple entry/exit button with a single press of the channel button

Activate code for channel button A, B or C

This example uses channel button A.

Deactivate code for channel button A, B or C

This example uses channel button A.

i. Press and hold 0

ii. While holding 0, press and release A

iii. Release 0

iv. Press A

v. Press your new code

vi. Press A

vii. Press your new code again

viii. Pre

ss A

i. Press and hold 0

ii. While holding 0, press and release A

iii. Release 0

iv. Press the existing code

v. Press A

vi. Press A

vii. Press A

www.ApolloGateOpeners.com | (800) 878-7829 | Sales@ApolloGateOpeners.com

Nice Apollo EDSWG/A Wireless Era Digital Keypad Quick start guide

Brand: Nice Apollo

Model: EDSWG/A Wireless Era Digital Keypad

Type: Quick start guide

Nice Apollo EDSWG/A Wireless Era Digital Keypad

Here are some of the features and possible use cases of the Nice Apollo EDSWG/A Wireless Era Digital Keypad:

Download PDF

report

Nice Apollo EDSWG/A Wireless Era Digital Keypad Quick start guide

Nice Apollo EDSWG/A Wireless Era Digital Keypad Quick start guide

Related papers

Other documents