Vizio CCU-11B is an intercom system that allows for various functions and additional equipment. Below you will find brief product information for Vizio CCU-11B:
- All Call Paging and Response: Page all stations simultaneously and respond from any station.
- Call Holding/Call Transfer: Place calls on hold and transfer them to another station.
- Calling Tone Duration: Adjust the duration of the calling tone.
- Time Interval Adjustment before All Call Paging Preannounce Tone: Set the time interval before the pre-announce tone for All Call Paging.
- Remote Control (Door): Use master stations to remotely open doors.
Vizio CCU-11B is an intercom system that allows for various functions and additional equipment. Below you will find brief product information for Vizio CCU-11B:
- All Call Paging and Response: Page all stations simultaneously and respond from any station.
- Call Holding/Call Transfer: Place calls on hold and transfer them to another station.
- Calling Tone Duration: Adjust the duration of the calling tone.
- Time Interval Adjustment before All Call Paging Preannounce Tone: Set the time interval before the pre-announce tone for All Call Paging.
- Remote Control (Door): Use master stations to remotely open doors.
INTERCOM SYSTEM
Central Control Unit
TOA ELECTRIC CO., LTD.
KOBE, JAPAN
TOA EXES-1
000
INTERCOM SYSTEM
CCU-11B
INSTALLATION HAND BOOK
133-21-012-7A
CONTENTS
Page
1. Introduction ................................................................ 2
2.
Functions which
Require
Additional Units
........................................
2
3.
Precautions
for
Installation
of
CCU-11B
...........................................
3
5. DIP
Switch
for
Function
Selection
on
CCU-11
B.
....................................
5
6.
Station
No. 11
Programming
for
Each
Function
................................
. . . . . 5
7.
Remote Control
Relay
(RY1
&
RY2)
on
CCU-11B.
.................................
.8
7-1 Functions and Operations ..............................................8
7-2 Connection ........................................................... .9
8.
Programming List
for
Functions
.................................................
10
4.
Initial CCU-11B Set Up
......................................................
.4
— 1 —— —
.
1. INTRODUCTION
This manual forms part of the Installation Manual for
TOA INTERCOM SYSTEM EXES-1000.
You may add to the CCU-11B to your TOA INTERCOM
SYSTEM EXES-1000, according to your specific needs,
to obtain various other functions.
Correct operation of these additional functions are not
available by only connection of the additional equip-
ments/devices.
Provision of such additional functions requires the
followings:
(1) Connection of the additional equipment, as required,
(2) Selection of functions which satisfy your needs and
setting up these functions in the respective equipment.
For (1) Connections of Equipment, etc., refer to Manual
of Installation Hand Book of EXES-1000 (EX-110)
Exchange.
This "Installation Hand Book of CCU-11B" deals prin-
cipally with (2) selection of functions and setting up of
respective equipment.
There are certain minimum installation requirements to
be met even though you may not need many additional
functions or additional equipment,
it is still necessary to
read "4. Initial CCU-11B Set Up (Page 4.)".
When you may
use only some of the additional functions or equipments,
it is not necessary to read instructions on unrequired
functions. Make sure, however, that careful study of the
necessary parts of this booklet should be done before
proceeding further.
EXES-1000 Installation Hand Book
EXES-1000 (EX-110)
Installation Handbook of Exchange.
or
EXES-1000 Installation Handbook
EXES-1000 (CCU-11B)
Installation Handbook
(133-21-012-7A)
2. FUNCTIONS WHICH REQUIRE ADDITIONAL UNITS
Functions of CCU-11B which require either the addition of specific units or processing in existing units are as men-
tioned below.
Function
Additional Equip-
ment Required
Unit Model No.
Remarks
Talk-Back from
paging speaker
Talk-Back Unit
TKU-11
Optional amplifier (10W max.) may be
required depending on application.
— 2 —
Please read following instructions carefully to ensure
proper operation of the CCU-11B.
1. Be careful about damage by static electricity as the
CCU-11B incorporates CMOS IC's. Do not touch com-
ponents and connectors.
2. Turn off the AC power switch when you take out or
insert the CCU-11B unit or any other unit.
3. Always insert the CCU-11B unit into the "CCU" slot.
Otherwise, there is a danger that the unit will be
damaged.
4. Make sure mini-jumper for battery back-up is always
placed in "ON" position each time it is used.
5. Incorrect setting of function select switches may lead
to incorrect performance.
3. PRECAUTIONS FOR INSTALLATION OF CCU-11B.
6. Even if you do not need programming functions, be
sure to carry out initial programming and registration
at station No. 11 when you install the new unit.
Otherwise, some other functions may not work
properly.
7. The Ni-Cd battery GB50-3FA1 is capable of saving im-
portant memory registration data even at times of
power failure and we suggest you replace it at least
every 4 years.
8. When shipping the CCU-11B unit independently, place
the mini-jumper for battery back-up in "OFF"
position. Then cover CCU back with cardboard, wrap
connector section in aluminium foil and put it in a con-
ductive bag.
— 3 —
PROGRAM SWITCH for No. 11 Programming
Set this in "ON" position only at time of initial pro-
gramming of the exchange and registration of functions.
In this case, station No. 11 is "programming station" but
becomes a normal station when switch is placed in "OFF"
position.
Remote Control
Replay Output
(RY1
and
RY2)
SW-B (1 ~ 6)/SW1 These switches
SW-A (1 ~ 6)/SW2 select functions.
Mini-Jumper for Battery Back-up.
Ni-Cd Battery
GB50-3FA1 (3.6V 50mAH)
4
INITIAL CCU-11B SET UP
Make sure that you have turned off the AC power switch.
Remove the CCU card from the card rack of exchange.
Set mini-jumper on the CCU card to "BATT. ON" position.
Set function selection DIP switches (SW-A & SW-B) on the CCU card for
required functions.
Insert the CCU card into the card rack of exchange, and make necessary
connection correctly.
Turn on the AC power switch of exchange.
Turn on PROGRAM switch on the CCU card.
No
First installation?
Yes
Initial set
Is all programming data required to be cleared?
No
Yes
Dial operation from station #11
Confirmation tone
Touch ten times
Is Continuously Called Station necessary?
Yes
To Continuous Calling Tone
No
Is Secretary Transfer necessary?
Yes
No
To Secretary Transfer
Is Master/Sub-station necessary?
Yes
To Master/Sub-station
Is Executive Priority necessary?
Yes
To Executive Priority
Dial operation from station #11.
Touch
Key.
Turn off PROGRAM switch on the CCU card of exchange.
Station #11 returns to an ordinary station.
— 4 —
5 DIP SWITCH FOR FUNCTION SELECTION ON CCU-11B
The DIP switches on the CCU-11B allow selection of the following functions;
Switches
Functions
DIP-SW "ON "Position DIP-SW "OFF "Position
Mini-Jumper for Battery
Battery "ON"
Position
Battery "OFF"
Position
OFF
OFF
Remote Control (Door)
Continues Calling Tone
OFF
OFF
Priority & Executive Priority
Press to Talk Control
Time Interval Adjustment
before All Call Paging Pre-
announce Tone
Calling Tone Duration
Call Transfer
All Call Paging & Response
Make/Break Relay Output
Activate
Activate
Activate
1 ~ 2
sec.
Short (0.7 sec)
Activate
Activate
One shot Relay Output
(4
sec.)
Not Activate
Not Activate
Not Activate
None
Long (1.3 sec)
Not Activate
Not Activate
Programming Switch
Station No. 11 is
"Programming station'
Station No. 11 is a
normal station
PROG
sw
SW-B (SW1)
SW-A (SW2)
1: BATT. OFF
2: BATT. ON
OFF
ON
A. All Call Paging and Response
B. Call Holding/Call Transfer
C. Calling Tone Duration
D. Time Interval Adjustment before All Call Paging
E. PTT Control
F. Priority and Executive Priority
G. Remote Control
H. Continuous Calling Tone
— 5 —
6. STATION NO. 11 PROGRAMMING FOR EACH FUNCTION
Use station #11 for programming of "Continuous Calling Tone", "Secretary Transfer", "Master/Sub-Relationship" and/or
"Executive Priority" functions.
Remarks: 1. In the event of failure to touch keys for correct dialing, privacy tone will be sound.
Re-start from the beginning.
2. When All Call Paging is used, the registration to the station #10 can not be done.
The following shows how to register the functions:
1. Continuous Calling Tone
New registration ?
No
Yes
Ascertain holding tone.
Continuously called station number
No
All registration finished ?
Yes
No
Release ?
Yes
Ascertain holding tone.
Station number to be released
No
Release finished ?
Yes
Return
— 6 —
2. Secretary Transfer
New registration ?
Station Number Station Number
of executive of secretary
Ascertain holding tone
All registration finished ?
Release ?
Station Number Station Number
of executive of executive
Ascertain holding tone
Release finished ?
Return
3. Master/Sub-Relationship
New registration ?
Sub-station Number Master station Number
Ascertain holding tone
All registration finished ?
Release ?
Sub-station Number Sub-station Number
Ascertain holding tone
Release finished ?
Return
4. Executive Priority
New registration ?
Number of station where Executive Priority is
registered.
Ascertain holding tone
All registration finished ?
Release ?
Number of station where registration of Executive
Priority is release.
Ascertain holding tone
Release finished ?
Return
— 7 —
7. REMOTE CONTROL RELAYS (RY1 & RY2) ON CCU-11B
Remark: Relay Control Capacity: 30VDC, 2A
Relays (RY1 & RY2) on CCU-11B are available for following functions.
Relay
No.
DIP Switch Position
Functions and Operations
SW-A-3 "OFF"
A Door Remote Control (One-shot-Make Relay Output)
Every master station can be used as a remote control device for door open-
ing. Touch dial
the door opening.
gives approximately 4 seconds make-contact for
SW-A-3 "ON"
RY1
B Door Remote Control (Make-Break Relay Output)
Every master station can be used as a remote control device for door
opening. Touch dial
gives continuous make-contact for door
opening. Then touch dial
gives break-contact for door closing.
SW-B-2 "OFF"
RY2
C Power ON/OFF Remote Control
When the system is used in conjunction with PA amplifier for the external
All-Call paging, the power switch of the PA amplifier can be turned on/off
with the relay built in the system. Touch dial
gives the make-contact
together with the All-Call function until the function is canceled by dialing
(Remark: Touch dial
gives break-contact of the relay.)
SW-B-2 "ON"
D Press To Talk Control
Touch dialing the specific station #17.
One way conversation is activated while the Press-To-Talk bar is continu-
ously depressed, same as the Press-To-Talk (selected simplex) function, and
the relay is activated with continuous make-contact.
One way conversation is reversed when the Press-To-Talk bar is released, and
the relay is activated with break-contact.
— 8 —
7-2. Connections
A. Connect 4-pin connector from TBM-11 (Terminal module) to P2 connection socket on the CCU-11B.
B. R M
1
terminals on TBM-11 are for the door remote control relay contacts and RM
2
terminals on TBM-11
are for the power ON/OFF remote control or press to talk remote control relay contacts.
(Please refer to the following diagram.)
YEL
DOOR
ORG
RED
BRN
AC
RM
2
AC
In the case of power ON/OFF remote control.
— 9 —
RM
1
8. PROGRAMMING LIST FOR FUNCTIONS
Use these tables to keep a record of those functions assigned to each station.
Function Table for Stations
Functions
Name
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Continuous
Calling
Tone
Executive
Priority
Secretary
Station
No.
Master
Station
No.
— 10 —
TOA ELECTRIC CO., LTD.
KOBE, JAPAN
Printed in Japan
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Vizio CCU-11B is an intercom system that allows for various functions and additional equipment. Below you will find brief product information for Vizio CCU-11B:
- All Call Paging and Response: Page all stations simultaneously and respond from any station.
- Call Holding/Call Transfer: Place calls on hold and transfer them to another station.
- Calling Tone Duration: Adjust the duration of the calling tone.
- Time Interval Adjustment before All Call Paging Preannounce Tone: Set the time interval before the pre-announce tone for All Call Paging.
- Remote Control (Door): Use master stations to remotely open doors.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Aiphone BA-1P Operating instructions
-
TOA Electronics CP-63 User manual
-
-
-
ViewSonic EXES-2000 User manual
-
TOA Electronics CP-66 User manual
-
Panasonic dBs Operating instructions
-
-
Sony HXCU-D70 User manual
-
Aiphone IS User manual
