COOLING FANS
Model Number: DF9010 DF1210 DF1610
INSTRUCTIONS FOR USE
Thank you for purchasing this product
Please read these instructions carefully before use
2
Important: This appliance is not intended for use by persons including children with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliances by a person responsible for their safety.
WARNING: To reduce the risk of burns, electric shock, fire or injury to persons:
1. Read all instructions before using the appliance.
2. This appliance is for domestic use only. This appliance is for indoor use only. Do not use outdoors.
3. Make sure the voltage in your home corresponds to the one shown on the rating label of the appliance.
4. Do not operate this appliance if it has a damaged cord or plug, if it is not working properly or if it has
been damaged or dropped. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
5. WARNING: Children should be supervised to ensure that they do not play with the appliance.
6. Place fan on a flat even surface.
7. Do not use an extension lead with this desk fan.
8. Do not operate the fan without the blade guard fitted.
9. Do not insert fingers or objects through the blade guard.
10. Do not use in damp areas such as bathrooms.
11. Do not use by a window.
12. Do not use with semi-conductors speed control.
13. This fan should not be operated without the base fitted or laying down.
14. Do not cover the power cord. Ensure the position of the cord does not pose a hazard.
15. Unplug the fan when not in use.
16. Do not operate in areas where flammable liquids such as paint and petrol are used.
17. This fan is a Class II product and does not require earthing.
1. Guard screw
2. Front guard
3. Blades
4. Guard mounting nut
5. Rear guard
6. Motor housing
7. Oscillation control
8. Stand
9. Speed controls
10. Base
11. Base screws
Desk / Clip Fan at a Glance
SAFETY INSTRUCTIONS
There is an additional cap that fastens in front of
the blades (3). To loosen this cap turn clockwise
and to tighten turn anti-clockwise.
3
1. Attach the base (10) to the stand (8) by using the 4 screws (11) provided.
2. Loosen guard mounting nut (4) from the motor housing (6).
3. Position rear guard (5) firmly to motor housing and then fasten by turning guard mounting nut clockwise
tightly.
4. Push the blade (3) along the motor shaft and fasten it firmly with the spinner by turning anti-clockwise.
5. Hang the front guard (2) to the rear guard with the position fixer provided at the rim of the guard and then
fix together with the screw and clips provided.
1. Check that the mains voltage complies with the voltage stated on this product.
2. Ensure the fan is placed on a flat even surface.
3. To control the speed of the fan, press the 1, 2 or 3 button on the base of the fan.
• 1 = Low Speed
• 2 = Medium Speed
• 3 = High Speed
Note: DF9010 only has 2 speed settings.
4. Push down the Oscillation control (7) to turn on the Oscillating function. Pull the Oscillation Control up to
turn it off. Ensure the fan will not be obstructed when oscillating
5. To turn the fan off, press the 0 button on the base. Switch off at the mains and remove the plug.
1. Turn off the fan and remove the plug from the wall socket before cleaning.
2. Use a dry soft cloth to remove any dust from the fan.
3. If the fan is particularly dirty use a soft damp cloth and wipe dry.
4. Do not use any chemicals or detergents as they will damage the fan.
5. Store the fan in a ventilated and dry area.
SPECIFICATIONS
Power Consumption:
220-240V, 50Hz
DF9010 Output:
20 Watts
DF1210 Output:
35 Watts
DF1610 Output:
40 Watts
Disposal of old electrical appliances The European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances must not be disposed of in normal unsorted
municipal waste. Old appliances must be collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you
dispose of the appliance it must be separately collected. Consumers should contact their local authority
or retailer for information concerning the correct disposal of their old appliance.
Disposal Information
Cleaning and Care
Operation
Assembly
This product carries a 2 year
guarantee. If you experience any
problems with your Igenix product
please call our Customer Services
Department on 01473 271 272.
4
View the range online at www.igenix.co.uk
Distributed by Pik-a-Pak Home Electrical
38 Bluestem Road, Ransomes Europark, Ipswich. IP3 9RR Tel: 01473 271 272
/
