Dunkirk DKVLT-100 Installation & Operation Manual

WALL MOUNTED

GAS BOILER

INSTALLATION, OPERATION &

MAINTENANCE MANUAL

An ISO 9001-2008 Certied Company

P/N# 240008888, Rev. M [01/2014]

Models

DKVLT-050

DKVLT-075

DKVLT-100

DKVLT-150

DKVLT-200

DKVLT-299

Manufactured by:

ECR International, Inc.

2201 Dwyer Avenue, Utica NY 13501

web site: www.ecrinternational.com

050/075/100/150/200

SIZE SHOWN

2

Description

Item

No. Illustration

Fully Assembled Boiler 1

Metal Wall Bracket 2

Lag Bolt, 3/8" x 3" Hex (4 ea) 3

*Safety Relief Valve 4

3/4" Tee 5

3/4" Nipple 6

3/4" x 1/4" Elbow 7

Air Vent 8

**Temperature Pressure Gauge 9

Bushing 3/4" x 1/4" 10

3/4" Tee (Same as No. 11) 11

Nipple 1¼ x 5½ 12

Drain Valve, 3/4" 13

3/4" Tee 14

Nipple 1¼ x 5½ 15

Bushing 7/8" OD, Heyco (2 ea) 16

Used for electrical wire knockouts.

Stopper, Rubber 5/16" (2 ea) 17 Used for packaging holes on back of boiler.

Plastic Plug (2 ea) 18 Used for packaging holes on back of boiler.

Outdoor Sensor 19 Used for measuring outside temperature.

Critical Installation Instruction 20 11" x 17" Page for critical installation issues.

Document Package 21 Includes essential documents.

4

5

6

7

8

2

3

9

10

12

13

14

11

15

299 SIZE

SHOWN

VERIFY CONTENTS RECEIVED

* Boiler provided with 30 psig (206 kpa) safety relief valve. Field source safety relief valve if system pressure

greater than 25 psig.

** Boiler provided with 75 psig temperature pressure gauge. Field source temperature pressure gauge if system

pressure greater than 60 psig.

3

(C)

DIMENSIONS

FIGURE 1-1 Dimensions

(D)

Wall Hanging

Bracket

(D)

(A)

(E)

Vent Connector

Combustion Air

Safety Relief

Valve

Connection

(¾ NPT)

(B)

Condensate Drain Connection (L)

Return Water (F)

Supply Water (F)

Gas Connection (K)

(G)

(J)

Table 1 : Physical Data

Models

050/075/100 150/200 299

Width (A) 20" (508mm)

23" (584mm)

Height (B) 30" (762mm)

40" (1041mm)

Depth (C) 14" (356mm)

16.0"

(406mm)

18.3"

(465mm)

Bracket (D) 28" (711mm)

40" (1016mm)

Height (E) 31" (787mm)

42" (1092mm)

Water

Connections

Size(F) 1-1/4" NPT

1-1/4" NPT

Location (G) 2" (51mm) 2" (51mm)

Location (H)

5" (127mm)

2" (51mm)

Location (I)

3" (76mm)

4-½"

(114mm)

Gas

Connection

Location (J) 4-1/2" (114mm) 4-1/2" (114mm)

Size (K)

1/2"

NPT

3/4"

NPT

Condensate Drain

Connection (L)

3/4" NPT

Weight

Shipping 111 lb (50 kg)

~182 lb

(83 kg)

~225 lb

(102 kg)

Unit 91 lb (41 kg)

~157 lb

(71 kg)

~195 lb

(89 kg)

Vent Connector 2" (51mm) 3" (76mm)

(H)

(I)

DIMENSIONS

4

1 - Introduction ............................................................................................................................... 5

2 - Important Safety Information ....................................................................................................6

3 - Component Listing ..................................................................................................................... 7

4 - Locating Boiler ......................................................................................................................... 11

5 - Hydronic Piping ........................................................................................................................ 13

5.2 Special Conditions ................................................................................................................. 13

5.3 Safety Relief Valve and Air Vent............................................................................................ 13

5.4 Trim Piping ........................................................................................................................... 14

5.5 System Piping....................................................................................................................... 14

6 - Combustion Air And Vent Piping ............................................................................................... 21

6.2 Removal of Existing Boiler From Common Vent System........................................................... 21

6.3 Venting Materials ................................................................................................................. 21

6.4 Vent Pipe Installation ............................................................................................................. 22

6.5 Vent Termination .................................................................................................................. 22

6.6 Venting Congurations ........................................................................................................... 23

6.7 Side Venting Terminal Requirements..........................................................................................28

6.8 Multiple Boiler Venting Installation............................................................................................30

6.9 Condensate Piping ................................................................................................................. 31

7 - Gas Supply Piping .................................................................................................................... 32

8 - Electrical Connections .............................................................................................................. 34

8.3 Line Voltage Connections ....................................................................................................... 34

8.4 External Connections ............................................................................................................. 34

9 - Start Up Procedure ................................................................................................................... 36

9.6 Perform CSD-1 Compliance Test ......................................................................................................40

9.7 Complete Start Up Procedure .................................................................................................. 41

10 - Operating Instructions ........................................................................................................... 42

11 - General Maintenance And Cleaning ........................................................................................ 43

12 - Ratings And Capacities ........................................................................................................... 46

13 - Trouble Shooting .................................................................................................................... 47

14 - Wiring Diagram ...................................................................................................................... 65

15 - Glossary ................................................................................................................................. 68

Appendix A - Control Module ......................................................................................................... 70

1.1 Introduction ......................................................................................................................... 70

1.2 Operation ............................................................................................................................. 70

1.3 Status Indication ................................................................................................................... 70

1.4 Sequence of Operation ........................................................................................................... 71

1.5 Theory of Operation .............................................................................................................. 73

TABLE OF CONTENTS

5

1.1 Designated Use

• Hot water heating boiler.

• Indoor installation.

• Closet or alcove installation.

• Direct vent boiler.

• For use with natural gas or liqueed petroleum gases

(LP/propane).

1.2 The unit MUST NOT:

• Directly heat potable water. Indirect heating is acceptable.

• Heat water with non-hydronic heating system chemicals

present (example, swimming pool water).

• Exceed 150 psig (1.03 MPa) maximum allowable

working pressure.

• Exceed 195°F (90.5°C) system design temperature.

1.3 Operational Features

• Modulating: 20-100%.

• Integral Dual Limit.

• Integral Low Water Cutoff (with test button).

• Outdoor Temperature Reset.

• Integral Multiple Boiler Control.

Check our website frequently for updates: www.ecrinternational.com

Information and specications outlined in this manual in effect at the

time of printing of this manual. ECR International reserves the right to

discontinue, change specications or system design at any time without

notice and without incurring any obligation, whatsoever.

1 - INTRODUCTION

6

2.3 Installation shall conform to requirements of

authority having jurisdiction or in absence of such

requirements:

• National Fuel Gas Code, ANSI Z223.1/NFPA 54

.

• National Electrical Code, NFPA 70.

2.4 Where required by authority having jurisdiction,

installation shall conform to Standard for Controls

and Safety Devices for Automatically Fired Boilers,

ANSI/ASME CSD-1.

Additional manual reset low water cutoff may be required.

2.5 Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not

limited to:

Installation by licensed plumber or gas tter.

NOTICE

Used to address practices not related to personal

injury.

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

!

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

!

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in death or serious injury

!

This is the safety alert symbol. Symbol alerts you to

potential personal injury hazards. Obey all safety messages

following this symbol to avoid possible injury or death.

2.2 Become familiar with symbols identifying

potential hazards.

2.1 General

Boiler installation shall be completed by qualied agency.

See glossary for additional information.

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in death or

serious injury. Read this manual and understand all

requirements before beginning installation.

!

2 - IMPORTANT SAFETY INFORMATION

7

3.1 Component Listing - Refer to diagrams on

following pages.

1.

User Interface Displays information regarding boiler

condition. Allows adjustment of boiler operating

parameters. NOTE: Does not replace thermostat used

to control central heating space.

2.

Combustion Air Inlet (2"/3") See section 6.

3.

Return Water From Heating System (In)

Connection supplied at bottom of boiler. See section 5.

4.

Low Voltage Terminal Strip Connection of all low

voltage wiring, including thermostat.

5.

Igniter

6.

Flame Sensor

7.

Sight Glass Permits observation of burner ame.

8.

Burner (see page 40)

9.

Heat Exchanger

10.

Condensate Collector

11.

Return Water Temperature Sensor

12.

Drain Valve (see page 14)

13.

Internal Primary Loop Ball Valve

14.

Supply Water Outlet to Heating System (Out)

Connections supplied for connecting from bottom of

boiler. See section 5.

15.

Vent Temperature Sensor

16.

Condensate Drain Boiler produces a liquid

(condensate) as a by-product of combustion. Condensate

must be piped to appropriate drain. See section 6.

17.

Heat Exchanger Pump

18.

Gas Shutoff Valve Fuel supply isolation during

servicing. See section 7

19.

Combustion Air Blower Delivers proper quantity of

combustion air, receives fuel from gas valve, mixes air

and fuel sending mixture to burner for combustion.

20.

Gas (Control) Valve Delivers proper quantity of fuel

to Combustion Air Blower. See section 7.

21.

Supply Water Temperature Sensor and High Limit

Switch

22.

Low Water Cutoff Senses inadequate quantity of

water. Turns off boiler before damage can occur.

23.

Safety Relief Valve Factory supplied, Field installed.

See section 5.

24.

High Voltage Junction Box For connection of 120V

components. See section 8.

25.

Vent Connector See section 6.

26.

Gas Connection See section 7.

27.

Wall Hanging Support Bracket (see page 12)

Integral to boiler. Allows wall mounting when used

with supplied wall mounting bracket. See section 4.

28.

Air Vent

29.

Boiler Control Module

30.

Lower Jacket Panel Gently pull upward then forward

to access.

31.

Transformer Supplies 24V power to low water cutoff.

32.

Flue Air Mixture Pressure Test Port - Not available

on all models.

33.

Combustion Analysis Test Port

34.

Internal Pump Relay - Not available on all models.

35.

Heat Exchanger Surface Temperature Switch

36.

ASME Plate

3 - COMPONENT LISTING

8

FIGURE 3-1 Boiler Components (Viewed from Back of Boiler)

VENT CONNECTOR

NOTE:

See Section 5-3 For

Safety Relief Valve

Piping Instructions

COMBUSTION

AIR INLET

SAFETY RELIEF VALVE

AIR VENT

FIGURE 3-3 Upper and Lower Jacket Latch (Viewed

from front of boiler)

Lift Jacket up,

engage jacket with

chassis,

push down.

FIGURE 3-2 Lower Jacket (Viewed from front of boiler)

Disconnect connector

before removing lower

jacket

Lower Jacket

Connector to User

Interface

(1) User Interface

Service Switch

Upper and Lower

Jacket Latch

WALL MOUNT

SUPPORT

BRACKET

3 - COMPONENT LISTING

9

FIGURE 3-4 Boiler Components 50/75/100 MBH (View from Front of Boiler) As seen on front cover

(18) GAS SHUTOFF

VALVE

(SHOWN IN OPEN

POSITION)

(25) VENT CONNECTOR

(19) COMBUSTION

AIR

BLOWER

(20) GAS (CONTROL)

VALVE

(22) LOW

WATER CUTOFF

(23) SAFETY RELIEF VALVE

(28) AIR VENT

(2) COMBUSTION

AIR INLET

NOTE:

See Section 5

For Piping

Instructions

(17) HEAT EXCHANGER

PUMP

(10) CONDENSATE

COLLECTOR

(3) RETURN WATER

FROM HEATING

SYSTEM (IN)

(14) SUPPLY WATER TO

HEATING SYSTEM (OUT)

(4) LOW VOLTAGE

TERMINAL STRIP

(15) VENT

TEMPERATURE

SENSOR

(26) GAS CONNECTION

(33) COMBUSTION

ANALYSIS TEST

PORT

(24) HIGH VOLTAGE

JUNCTION BOX

(9) HEAT

EXCHANGER

(29) BOILER

CONTROL

MODULE

Fuse and

Holder

(5) IGNITER

(6) FLAME

SENSOR

(7) SIGHT GLASS

(32) FLUE

AIR MIXTURE

PRESSURE

TEST PORT

(16) CONDENSATE

DRAIN

(31) TRANSFORMER

(11) RETURN WATER

TEMPERATURE SENSOR

(13) INTERNAL PRIMARY

LOOP BALL VALVE

(35) HEAT EXCHANGER

SURFACE TEMPERATURE

SWITCH

3 - COMPONENT LISTING

(36) ASME

PLATE

(21) SUPPLY WATER

TEMPERATURE SENSOR

& HIGH LIMIT SWITCH

10

FIGURE 3-5 Boiler Components 299 MBH (View from Front of Boiler)

(18) GAS SHUTOFF

VALVE

(SHOWN IN OPEN

POSITION)

(25) VENT CONNECTOR

(20) GAS (CONTROL)

VALVE

(22) LOW WATER

CUTOFF

(21) SUPPLY WATER

TEMPERATURE SENSOR &

HIGH LIMIT SWITCH

(23) SAFETY RELIEF VALVE

(28) AIR VENT

(2) COMBUSTION

AIR INLET

NOTE:

See Section 5

For Piping

Instructions

(17) HEAT EXCHANGER

PUMP

(10) CONDENSATE

COLLECTOR

(3) RETURN WATER

FROM HEATING

SYSTEM (IN)

(14) SUPPLY WATER TO

HEATING SYSTEM (OUT)

(4) LOW VOLTAGE

TERMINAL STRIP

(33) COMBUSTION

ANALYSIS TEST

PORT

(26) GAS CONNECTION

(24) HIGH VOLTAGE

JUNCTION BOX

(9) HEAT

EXCHANGER

(29) BOILER CONTROL

MODULE

Fuse and Holder

(6) FLAME SENSOR

(16) CONDENSATE

DRAIN

(31) TRANSFORMER

(13) INTERNAL PRIMARY

LOOP BALL VALVE

(19) BLOWER

VENTURI

(35) HEAT

EXCHANGER SURFACE

TEMPERATURE SWITCH

(34) INTERNAL

PUMP RELAY

(7) SIGHT GLASS &

(5) IGNITER

(15) VENT TEMPERATURE

SENSOR

(11) RETURN

TEMPERATURE

SENSOR

3 - COMPONENT LISTING

(36) ASME

PLATE

11

FIGURE 4-1 Clearance to Combustible Materials

TABLE 2: BOILER CLEARANCES

Dimension

Combustible

Materials

(1)

Service

(1)(2)

Model

050/075/100/

150/200/299

050/075/100/

150/200/299

Top (A)

0" (0 cm) 14" (36 cm)

Left Side (B)

0" (0 cm) 0" (0 cm)

Right Side (C)

0" (0 cm) 0" (0 cm)

Front (D)

0" (0 cm) 6" (16 cm)

Back (E)

0" (0 cm) 0" (0 cm)

Bottom (F)

0" (0 cm) 12" (32 cm)

Combustion Air/Vent

piping

0" (0 cm)

6" (16 cm)

Hot Water Piping

See local code 6" (16 cm)

(1)

Required distances measured from boiler jacket.

(2)

Service, proper operation clearance recommendation.

A

E

D

A

C

B

A

FLOOR

F

4.1 Boiler Location Considerations

• Ambient room temperature always above 32°F (0°C) to

prevent freezing of liquid condensate.

• Approved for installation in closets.

• Protect gas ignition system components from water

(dripping, spraying, rain, etc.) during operation and

service (circulator replacement, condensate trap, control

replacement, etc.).

• Wall mount only.

• Access to outdoors to meet minimum and maximum

pipe lengths for combustion air and vent piping. See

section 6.

• Disposal of condensate. See section 6.

• Drainage of water (or water - antifreeze solution) during

boiler service or from safety relief valve discharge. See

section 5.

• Access to system water piping, gas supply, and electrical

service. See sections 5, 7 and 8.

• Clearances to combustible materials and service

clearances. See Table 2 and gure 4-1.

• Multiple Boilers can be wall mounted, placed side by

side, or back to back.

4 - LOCATING BOILER

12

4.2 Pre-pipe supply and return water connections

with factory ttings before wall mounting.

4.3 Wall Mounting

Mount boiler on wall using wall mounting bracket included

with unit.

• Structure must be capable of supporting boiler weight

plus 60 lbs (28 kg). See Table 1, page 2.

• Wall mount bracket has 4 slots allowing mounting on

two (2) wall studs spaced at 11½" to 16½" on center.

See gure 4-2.

• Boiler includes (4) 3/8" x 3" lag screws and (4) washers

for attaching wall mount bracket to wood studs. Field

source appropriate fasteners for other wall constructions

(masonry, concrete).

• Attach wall mount bracket level on wall.

• Boiler must engage with wall mount bracket.

• Avoid overhang on sides of wall mount bracket. Verify

boiler bracket is centered on wall bracket. See gure

4-2.

WARNING

Fire, explosion hazard. Mount boiler vertically or

slightly tilted backward to insure proper function of

low water cutoff. Failure to follow these instructions

could result in death or serious injury.

• When mounting boiler onto wall insert two plastic

stoppers and two plastic plugs to packaging holes on

back of boiler. See parts listed on page 2, number 17

and 18.

• Mount boiler vertically or slightly tilted backward to

insure the low water cutoff functions properly. See

gure 4-3 for low water cutoff orientation.

FIGURE 4-2 Wall Mount Bracket Engaged with

Bracket on Boiler

CAUTION

Boiler weight exceeds 75 pounds (34 kg). Do not

lift boiler onto wall without assistance.

!

4 Slots for attaching

Wall Mount Bracket

to Studs

NOTICE

Lift boiler using chassis. Using front jacket, vent

piping, water or gas ttings to lift boiler may cause

damage to the boiler.

Center brackets. Avoid

overhang on sides of

wall mount bracket.

4 - LOCATING BOILER

FIGURE 4-3 Low Water Cutoff Orientation

5° ~ 15°

Factory Default

10°

13

5.1 General

• Install piping in accordance with authority having jurisdiction.

NOTICE

Use two (2) wrenches when tightening and tting

to pipe boiler's threaded ttings. Boiler's internal

piping can be damaged if subjected to excessive

torque.

• Support system piping and safety relief valve discharge

piping. Boiler's internal piping and wall mount bracket can

be damaged if subjected to excessive weight.

• Size central heating pump (and domestic hot water

pump, if used) for system requirements only. Internal

heat exchanger pump compensates for pressure drop

through boiler internal piping and heat exchanger.

• Thoroughly clean and ush system before connecting to

boiler.

• If oil is present in system water, use approved detergent to

wash system.

• Flush system to remove any solid objects such as metal

chips, bers, or Teon tape, etc.

5.2 Special Conditions

• System piping exposed to freezing conditions: Use

inhibited propylene glycol solutions certied by uid

manufacturer for use with closed water heating system.

Do not use automotive or ethylene glycol.

• Boiler installed above radiation level (or as required by

authority having jurisdiction). Integral low water cutoff

provided in boiler. See pages 9 & 10.

• Boiler used in connection with refrigeration system.

Install piping in parallel with boiler, with appropriate

valves to prevent chilled medium from entering boiler.

• System piping connected to heating coils located in air

handling unit exposed to refrigerated air circulation. Install

ow control valves or other automatic means to prevent

gravity circulation of boiler water during cooling cycle.

5.3 Safety Relief Valve and Air Vent

NOTICE

Boiler rated at 150 psig (1.03 MPa) maximum

allowable working pressure. Boiler provided with

30 psig (206 kPa) safety relief valve. Field source

safety relief valve for system pressures greater

than 25 psig. Temperature Pressure Gauge and Air

Vent satisfactory for 75 psig operation. Field source

temperature pressure gauge for system pressures

greater than 60 psig.

• Install safety relief valve and air vent using pipe ttings

provided with boiler. See gure 5-1

• Install safety relief valve with spindle in vertical position.

• Do not install shutoff valve between boiler and safety

relief valve.

WARNING

• Poison hazard. Ethylene glycol is toxic. Do not

use ethylene glycol.

• Never use automotive or standard glycol antifreeze,

even ethylene glycol made for hydronic systems.

• Ethylene glycol can attack gaskets and seals used

in hydronic systems.

• Use only inhibited proplyene glycol solutions

certied by uid manufacturer as acceptable for

use with closed water heating system.

• Thoroughly clean and ush any system that used

glycol before installing new Boiler.

• Provide user with Material Safety Data Sheet

(MSDS) on uid used.

!

NOTICE

Do not expose boiler and condensate piping to

freezing temperatures.

FIGURE 5-1 Safety Relief Valve & Air Vent (Viewed

from front of boiler)

Safety Relief

Valve

3/4" NPT

Nipple

3/4" x 1/4" NPT

90° Elbow

3/4"F x 3/4"M

NPT Tee

3/4 NPT

Air Vent

Position Air Vent and Safety Relief Valve

to provide space for discharge piping.

5 - HYDRONIC PIPING

14

• Install discharge piping from safety relief valve. See

gure 5-2.

• Use ¾" or larger pipe.

• Use pipe suitable for temperatures of 375°F (191°C)

or greater.

• Individual boiler discharge piping shall be independent

of other discharge piping.

• Size and arrange discharge piping to avoid reducing

safety relief valve relieving capacity below minimum

relief valve capacity stated on rating plate.

• Run pipe as short and straight as possible to location

protecting user from scalding and properly drain

piping.

• Install union, if used, close to safety relief valve outlet.

• Install elbow(s), if used, close to safety relief valve

outlet and downstream of union (if used).

• Terminate pipe with plain end (not threaded).

5.4 Trim Piping

• Temperature - Pressure Gauge. Install temperature

pressure gauge using nipple, tee and bushing provided

with boiler. See gure 5-3.

• Drain Valve. Install drain valve using nipple, tee and

bushing provided with boiler. See gure 5-3.

5.5 System Piping

• See Table 3 for basic system piping congurations.

• Systems with automatic ll valves require back ow

prevention device.

• Single boiler system. See gures 5-4, 5-5, 5-6, 5-7A, & B

for general guidance. Additional considerations:

• Boiler control is designed for single central heating

pump. Installer responsible for integration of

multiple central heating pumps.

• Boiler control allows domestic hot water

prioritization. Function could be lost if central

heating pump not directly connected to control

system.

• Multiple boiler system.

See gure 5-8A, B & C

for general

guidance. Additional considerations:

• Control system requires equivalent water

temperatures entering each boiler to properly

sequence and adjust system supply temperature.

• Install multi boiler sensor kit. See "Parts, Kits &

Optional Accessories" manual for part number.

• Heating system with existing primary loop, close internal

primary loop ball valve.

• Heating system without existing primary loop, leave internal

primary loop ball valve open to use internal primary loop.

FIGURE 5-3 Temperature Pressure Gauge and Drain

Valve Installations

Temperature Pressure

Gauge shown at

System Supply

Connection

Check Local Codes

For Maximum

Distance To Floor

WARNING

Burn and scald hazard. Safety relief valve could

discharge steam or hot water during operation.

Install discharge piping per these instructions.

!

FIGURE 5-2 Safety Relief Valve Discharge Piping

Drain Valve shown

at System Return

Connection to Boiler

Safety Relief Valve

Gas Supply

5 - HYDRONIC PIPING

15

Piping Legend

FIGURE 5-4 System Piping

NOTICE

Illustrations are meant to show system piping

concept only. Installer responsible for all

equipment and detailing required by authority

having jurisdiction.

System

Return

System

Supply

Safety Relief Valve

WALL

MOUNTED

ONLY

Pipe to

condensate

drain

Table 3 - System Piping Congurations

Single Boiler

Two Pipe Zoned System

With Zone Valves gure 5-5

With Zone Pumps gure 5-6

Primary/Secondary Pumping

Closed External Primary Loop

gure 5-7A

Open External Primary Loop gure 5-7B

Multiple Boilers

Two Pipe Zoned System

With Zone Valves gure 5-8A

With Zone Pumps Not Shown

Primary/Secondary Pumping

Closed External Primary Loop gure 5-8B

Open External Primary Loop

gure 5-8C

5 - HYDRONIC PIPING

16

FIGURE 5-5 Single Boiler Two-Pipe Zoned System With Zone Valves

FIGURE 5-6 Single Boiler Two-Pipe Zoned System With Zone Pumps

Heat exchanger

ball valve open

(as shipped)

Heat exchanger

ball valve open

(as shipped)

DHW

Pump

CH/System

Pump

DHW

Pump

Zone

Pump

5 - HYDRONIC PIPING

3/8"/10mm Open

End Wrench may

be required to

turn valve

3/8"/10mm Open

End Wrench may

be required to

turn valve

17

Heating Load Heating Load

Heating Load

CH/System

Pump

12"(305mm) Maximum

separation

12"(305mm)

Maximum

separation

Existing closely spaced tees

in primary system loop

Heating Load Heating Load

Heating Load

FIGURE 5-7A Single Boiler Using Primary/Secondary Pumping With Closed External Primary Loop

Heating system

with existing

primary loop.

Internal primary

loop ball valves

closed

FIGURE 5-7B Single Boiler Using Primary/Secondary Pumping With Open External Primary Loop

CH/System

Pump

12"(305mm) Maximum

separation

Existing closely spaced tees

in primary system loop

Limit length

to

5' (1.6m)

12"(305mm)

Maximum

separation

Limit length

to

5' (1.6m)

Internal primary loop

ball valves open.

Heating system

without existing

primary loop.

5 - HYDRONIC PIPING

3/8"/10mm Open

End Wrench may

be required to

turn valve

3/8"/10mm Open

End Wrench may

be required to

turn valve

18

FIGURE 5-8A Multiple Boiler Two Pipe Zoned System With Zone Valves - (See Multiple Boiler Guide)

5 - HYDRONIC PIPING

Up to 16

boilers

DHW

Pump

(See Multiple Boiler Guide)

CH/System

Pump

12"/305mm Maximum Separation

System

Temperature

Sensor

Size common piping

per maximum heat

capacity of entire

system

All internal

primary loop

ball valves

closed

Limit

length to

5' (1.6m)

3/8"/10mm Open

End Wrench may

be required to

turn valve

19

FIGURE 5-8B Multiple Boilers Using Primary/Secondary Pumping with Closed External Primary Loop

5 - HYDRONIC PIPING

Heating Load Heating Load

Heating Load

Existing closely spaced tees

in primary system loop

12"/305mm

Maximum

Separation

Up to 16

boilers

CH/System

Pump

12"/305mm Maximum Separation

System

Temperature

Sensor

Size common piping

per maximum heat

capacity of entire

system

All internal

primary loop

ball valves

closed

Limit

length to

5' (1.6m)

3/8"/10mm Open

End Wrench may

be required to

turn valve

20

5-8C Multiple Boilers Using Primary/Secondary Pumping with Open External Primary Loop

Existing closely spaced tees

in primary system loop

12"/305mm

Maximum

Separation

CH/System

Pump

12"/305mm Maximum Separation

System

Temperature

Sensor

Size common piping

per maximum heat

capacity of entire

system

Heat exchanger

ball valve open

(as shipped)

Limit

length to

5' (1.6m)

5 - HYDRONIC PIPING

3/8"/10mm Open

End Wrench may

be required to turn

valve

Up to 16

boilers

Page is loading ...

Dunkirk DKVLT-100 Installation & Operation Manual

Dunkirk DKVLT-100 Installation & Operation Manual

Related papers

Other documents