Little GIANT 506858 Owner's manual

Brand: Little GIANT

Model: 506858

Category: Water pumps

Type: Owner's manual

littlegiant.com

6EC & 10EC SERIES

Owner’s Manual

Sump Pumps

Table of Contents

SAFETY INSTRUCTIONS - - - - - - - - - 2

INTRODUCTION - - - - - - - - - - - - - 4

Product Description - - - - - - - - - 4

Specifications - - - - - - - - - - - - 4

INSTALLATION - - - - - - - - - - - - - 5

Physical Installation - - - - - - - - - - 5

Electrical Connections - - - - - - - - 7

OPERATION TESTING - - - - - - - - - - 8

Testing Automatic Pump Operation - - 8

Testing Manual Pump Operation - - - 9

MAINTENANCE - - - - - - - - - - - - - 10

Periodic Service - - - - - - - - - - - 10

Troubleshooting - - - - - - - - - - - 11

Replacement parts - - - - - - - - - - 12

LIMITED WARRANTY - - - - - - - - - - 13

SAFETY INSTRUCTIONS

Hazard Messages

SAFETY INSTRUCTIONS

Hazard Messages

This manual includes safety precautions and other important

information in the following formats:

IMPORTANT: Identifies information that controls correct assem-

bly and operation of the product.

NOTE: Identifies helpful or clarifying information.

This symbol alerts the user to the presence of dangerous

voltage inside the product that might cause harm or elec-

trical shock.

This symbol alerts the user to the presence of hot sur-

faces that might cause fire or personal injury.

Before Getting Started

This equipment should be installed and serviced by technically

qualified personnel. Failure to comply with national and local

electrical and plumbing codes and within Franklin Electric recom-

mendations may result in electrical shock or fire hazard, unsatis-

factory performance, or equipment failure.

Know the product’s application, limitations, and potential haz-

ards. Read and follow instructions carefully to avoid injury and

property damage. Do not disassemble or repair unit unless

described in this manual.

Refer to product data plate(s) for additional precautions, operat-

ing instructions and specifications.

Failure to follow installation/operation procedures and all appli-

cable codes may result in the following hazards:

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in minor or

moderate personal injury.

Indicates a potentially hazardous situation

which, if not avoided could result in damage to

equipment or other property.

Risk of death, personal injury, or

property damage due to explosion, fire,

or electric shock.

• Do not use to pump flammable or explosive fluids such as

gasoline, fuel oil, kerosene, etc.

• Do not use in explosive atmospheres or hazardous loca-

tions as classified by the NEC, ANSI/NFPA70.

• Do not handle a pump or pump motor with wet hands or

when standing on a wet or damp surface, or in water.

• When a pump is in its application, do not touch the motor,

pipes, or water until the unit is unplugged or electrically

disconnected.

• If the power disconnect is out of site, lock it in the open

position and tag it to prevent unexpected application of

power.

• If the disconnect panel is not accessible, contact the elec-

tric company to stop service.

SAFETY INSTRUCTIONS

Before Getting Started

High voltages capable of causing severe

injury or death by electrical shock are

present in this unit.

• To reduce risk of electrical shock, disconnect power before

working on or around the system. More than one discon-

nect switch may be required to de-energize the equipment

before servicing.

• This product is supplied with a grounding conductor and

grounding-type attachment plug. To reduce risk of electric

shock, be certain that it is connected only to a properly

grounded grounding-type receptacle. Do not remove the

third prong from the plug. The third prong is to ground the

pump to help prevent possible electric shock hazard. Do

not use an extension cord.

• Check electrical outlets with a circuit analyzer to ensure

power, neutral, and ground wires are properly connected.

If not, a qualified, licensed electrician should correct the

problem.

• Wire pump system for correct voltages.

• The pump has been evaluated for use with water only.

Pump should only be used with liquids compatible with

pump component materials. If the pump is used with liq-

uids incompatible with the pump components, the liquid

can cause failure to the electrical insulation system result-

ing in electrical shock.

Risk of damage to pump or other equipment.

• Do not use this pump for pumping sea water, beverages,

acids, chemical solutions, or any other liquid that pro-

motes corrosion as this can result in damage to the pump.

• Do not run pump dry. For optimal cooling and to prolong

the motor life, the liquid level being pumped should nor-

mally be above the top of the pump housing.

• This pump is not suitable for pond applications.

Risk of bodily injury, electric shock,

or equipment damage.

• This equipment must not be used by children or persons

with reduced physical, sensory or mental abilities, or lack-

ing in experience and expertise, unless supervised or

instructed. Children may not use the equipment, nor may

they play with the unit or in the immediate vicinity.

• Equipment can start automatically. Always unplug the

pump power cord and disconnect the electrical power

before servicing the pump or switch.

• An inoperative or malfunctioning pump could lead to

flooding, resulting in personal injury or property damage.

• In applications where property damage and/or personal

injury might result from an inoperative or leaking pump

due to power outages, discharge line blockage, or any

other reason, an automatic back-up system and/or an

alarm should be installed.

• Do not run the pump dry. If run dry, the surface tempera-

ture of the pump will rise to a high temperature that could

cause skin burns if touched and will cause serious damage

to the pump.

• Do not oil the motor. The pump’s motor housing is sealed,

and contains a high-grade dielectric oil for heat transfer

and lifetime lubrication. Use of other oils could cause seri-

ous electric shock and/or permanent damage to the

pump.

• Operation of this equipment requires detailed installation

and operation instructions provided in this manual for use

with this product. Read entire manual before starting

installation and operation.

• End User should receive and retain manual for future use.

• Keep safety labels clean and in good condition.

• Keep work area clean, well-lit, and uncluttered.

• Wear safety glasses while installing or performing mainte-

nance on the pump.

• Do not wear loose clothing, jewelry, or anything that may

be caught in the rotating parts. Tie up long hair and

remove jewelry.

INTRODUCTION

Product Description

INTRODUCTION

Product Description

This submersible pump is for use in basins or lift stations and is suitable for pumping clear water or effluent

gray water with up to 1/2" spherical semi-solids. Do not use the pump in applications where sewage or any other

debris (gravel, sand, floating debris, etc.), abrasives, or corrosives are present.

This product has been carefully tested, inspected, and packaged to ensure safe delivery and operation.

Please examine your item(s) carefully to ensure that no damage occurred during shipment. If damage has

occurred, please contact the place of purchase. They will assist you in replacement or repair, if required.

The pump motor is equipped with an automatic resetting thermal protector and may restart unexpectedly.

Protector tripping is an indication of motor overloading/overheating, which can be caused by application

issues such as an obstructed pump impeller, switch stuck in the ON position, pump running dry, pump air-

locked, pump short cycling, excessively high or low voltage supply, or possibly a pump, motor, bearings or

seal that have reached the end of their useful life.

Specifications

Gallons/Liters per Minute, at Height

Height 5 ft

1.5 m

10 ft

3 m

15 ft

4.5 m

20 ft

6.1 m

30 ft

9.1 m Shut Off

6EC 53 GPM 50 GPM 42 GPM 34 GPM –28 feet

8.5 meters

201 LPM 189 LPM 159 LPM 129 LPM

10EC 67 GPM 57 GPM 47 GPM 42 24 GPM 36 feet

11 meters

254 LPM 216 LPM 178 LPM 159 LPM 91 LPM

INSTALLATION

Physical Installation

INSTALLATION

Physical Installation

1. Pump must be installed in a suitable gas-tight basin that is at least 18" in diameter and 24" deep and

vented in accordance with local plumbing codes.

2. Clean any debris from the basin and set the pump in the center of the basin (refer to “Typical Installa-

tion” on page 6). A solid bottom will prevent clogging of the pump from sand and dirt.

3. The pump must be placed on a hard, level surface. Never place the pump directly on clay, earth or

gravel surfaces. These surfaces contain small stones, gravel, sand etc. that may clog or damage the

pump and cause pump failure.

4. Do not attempt to restrict the intake side of these pumps. Restricting the intake may cause damage to

the seal and may starve the pump. If reduced flow rates are required, place a valve on the discharge

side of the pump. Or, if flexible vinyl tubing is used, a clamp can be used on the tubing to restrict the

flow.

5. Connect discharge piping. Use pipe joint compound at all connections. Sump pumps can be piped to

discharge into the house drainage system, to a dry well, splash block, or to a storm drain, depending on

local plumbing codes. The discharge pipe should be as short as possible and contain as few elbows as

possible. The discharge pipe should be the same diameter as the discharge size to reduce pipe friction

losses. A smaller pipe will restrict capacity and reduce pump performance. The pump comes with a 1-1/

2" female pipe thread discharge.

• Support the pump and piping while assembling and when installed. Failure to do so may cause the

piping to break, the pump to fail, motor bearing failures, etc.

• Always install a union in the discharge line just above the basin cover to allow for easy removal of

the pump for cleaning or repair.

6. A check valve must be used in the discharge line to prevent backflow of liquid into the basin. The check

valve should be a free-flow valve that will easily pass solids.

7. Tape the pump and switch cords to the discharge line with electrical tape. This will protect the cord

from damage.

Risk of severe injury or death by electrical shock.

• Always disconnect the electrical power before touching the pump or discharge.

• Check local electrical and building codes before installation. The installation must be in accordance with

their regulations as well as the most recent National Electrical Code (NEC).

Risk of property damage due to flooding.

• Do not install the check valve in a vertical position, as solids may settle in the valve and prevent the

valve from opening on start-up. For best performance of the check valve when handling solids,

install it in a horizontal position or at an angle of no more than 45°.

• When a check valve is used, drill a relief hole (1/8" or 3/16" in diameter) in the discharge pipe. This

hole should be located below the floor line between the pump discharge and the check valve. Unless

such a relief hole is provided, the pump could “air lock” and will not pump water even though it will

run.

INSTALLATION

Physical Installation

8. Test the operation of the pump system by following the instructions in “Operation Testing” on page 8 of

this manual. Do not attempt to operate the pump without water; this will damage the seals and bear-

ings and could result in permanent damage to the pump.

9. Place cover over basin. This cover will help prevent debris from entering the pit and will guard against

accidental injury.

Typical Installation

INSTALLATION

Electrical Connections

Check the pump label for proper voltage required. Do not connect to voltage other than that shown.

A ground fault circuit interrupter (GFCI) is required.

The pump should be connected or wired to its own circuit, with no other outlets or equipment in the circuit

line. The fuses and circuit breaker should be of ample capacity in the electrical circuit.

The 6EC-CIA-RF and 10EC-CIA-RF pumps have automatic switches with piggyback plugs on the switch

cords. For automatic operation, plug the pump cord into the float switch cord. Plug the float switch cord

(with pump cord attached) into the GFCI outlet.

Pump HP Voltage Breaker Amps

6EC 1/3 115 V 15 A

10EC 1/2 115 V 15 A

Risk of severe injury or death by electrical shock.

• Always disconnect the electrical power before touching the pump or discharge.

• Check local electrical and building codes before installation. The installation must be in accordance

with their regulations as well as the most recent National Electrical Code (NEC).

• The flexible jacketed cord assembly mounted to the pump must not be modified in any way, with the

exception of shortening the cord to fit into a control panel. Any splice between the pump and the

control panel must be made within a junction box mounted outside of the basin and comply with the

National Electrical Code. Employ a licensed electrician.

• Do not use the power cord for lifting the pump.

• Do not remove the third prong from the plug, or cut plug from cord. These actions will void the war-

ranty.

• Do not use an extension cord.

OPERATION TESTING

Testing Automatic Pump Operation

OPERATION TESTING

If the pump does not operate properly, consult “Troubleshooting” on page 11. If the solution still cannot be

found, please contact the place of purchase or an authorized service center.

Do not let the unit run dry (without liquid). It is designed to be cooled by pumping fluid. The seal may be

damaged and the motor may fail if the pump is allowed to run dry.

If the unit is going to be idle for a period of time, follow the cleaning instructions outlined in the next sec-

tion. Do not let the unit freeze. This may cause cracking or distortion that may destroy the unit.

Testing Automatic Pump Operation

The 6EC-CIA-SFS and 10EC-CIA-SFS automatic pumps are equipped with an integral float-operated

mechanical switch. Automatic operation is achieved through the pump cord.

The 6EC-CIA-RF and 10EC-CIA-RF pumps have automatic switches with piggyback plugs on the switch

cords. The pump must be plugged into piggyback switch cord for automatic operation.

When these pumps are installed in a basin with a sealed cover, switch operation cannot be observed. The

basin cover will usually have a spare hole that is plugged with a rubber plug. This plug can be removed and

switch operation can be observed.

To test system operation, follow these steps:

1. Plug the power cord into a grounded receptacle with voltage consistent with the pump voltage, as indi-

cated on the pump nameplate.

2. Be sure the gate valve in the discharge line is open.

3. Run water into the basin until the pump is activated.

Do not attempt to run the pump without water; this could result in permanent damage to the pump.

4. Confirm that the pump and its control switch are functioning as intended.

5. Confirm that the ON/OFF levels are within specification, and confirm that no potential obstructions

exist that could inhibit switch operation.

6. Confirm that there are no leaks in the pump discharge plumbing and main home drain pipe plumbing.

NOTE: It is normal for a stream of water to spray from the air bleed hole in the pump’s plumbing.

(Water sprays out of a hole by a bolt on the base of the unit.) Confirm that this spray is captured within

the basin.

7. Allow the pump to operate through several on/off cycles.

Risk of damage to pump or other equipment.

• Do not attempt to run the pump without water; this could result in permanent damage to the pump.

• If pump is run dry, it may damage pump and will void the warranty.

OPERATION TESTING

Testing Manual Pump Operation

The 6EC-CIM and 10EC-CIM manual pumps do not include an automatic liquid level control. The pump cord

for these pumps can be plugged directly into a properly grounded receptacle with voltage consistent with

the pump nameplate for continuous pump operation.

For automatic operation of a manual pump, a separate float switch or other liquid level control may be used.

If a float switch or level control has been added, refer to “Testing Automatic Pump Operation” on page 8 for

testing operation.

To test manual pump operation, follow these steps:

1. Connect a discharge hose to the pump’s discharge port.

2. Place pump into a basin or test reservoir.

3. Direct the opposite end of the discharge hose back into the basin or test reservoir so that the water dis-

charged from the hose during testing will be contained within the basin or test reservoir. Secure the

hose to prevent the water pressure created during testing from causing the hose to exit the basin or

test reservoir.

4. If there is a valve on the discharge hose, be sure the valve is open.

5. Using a separate water source, fill the basin or test reservoir until the pump is fully submerged.

Do not attempt to run the pump without water; this could result in permanent damage to the pump.

Do not overfill the basin or test reservoir.

6. Plug the pump’s power cord into a ground fault circuit interrupter (GFCI) receptacle with voltage con-

sistent with the pump voltage, as indicated on the pump nameplate.

7. Confirm that the pump is functioning as intended.

NOTE: It is normal for a stream of water to spray from the air bleed hole in the pump’s plumbing.

(Water sprays out of a hole by a bolt on the base of the unit.) Confirm that this spray is captured within

the basin.

8. If pump is not functioning as intended, unplug the pump’s power cord from the receptacle and refer to

“Troubleshooting” on page 11. If the solution still cannot be found, please contact the place of purchase

or an authorized service center.

9. If the pump is functioning as intended, unplug the pump’s power cord from the receptacle before

attempting to remove it from the basin or test reservoir.

Risk of bodily injury or damage to pump or other equipment.

• Manual, continuous pump operation should be used only for emergencies, or when a large volume of

water is to be pumped. The pump must be continuously monitored during operation and discon-

nected from power before the pump runs dry.

• If an accessory float switch or other liquid level control is installed, refer to manufacturer’s instruc-

tions. Failure to install control in compliance with national and local electrical and plumbing codes

and within manufacturer’s recommendations may result in electrical shock or fire hazard, unsatisfac-

tory performance, or equipment failure.

MAINTENANCE

Periodic Service

MAINTENANCE

Periodic Service

Inspect and test the pump system condition and operation every three months—more frequently in heavy

use applications.

Let pump cool for a minimum of 2 hours before attempting to service. Submersible pumps contain oil that

becomes pressurized and hot under normal operating conditions.

1. Check the power cords and electrical outlet for damage or corrosion. The power cord on these units

cannot be replaced. In case of damage, the whole unit must be replaced.

2. Remove all debris (gravel, sand, floating debris, etc.) from the basin.

3. Check the pump system components (basin, pump, switch, etc.) for any build-up (sludge, sediment,

minerals, etc.) that would inhibit functionality of the components. If significant, remove build-up or

replace affected components.

4. Confirm that all flexible coupling hose clamps are fully engaged with plumbing and fully tightened.

5. Test operation of the pump system. Refer to “Operation Testing” on page 8.

6. While the pump is running, make sure a stream of water is escaping from the air bleed hole. If not, clear

the hole of any deposits or debris.

Cleaning Impeller and Volute

Periodic cleaning of the pump parts will prolong the life and efficiency of the pump. Refer to the assembly

and disassembly of the pumping head.

1. Remove the five screws that hold the base to the volute, then separate the base from the volute. Do not

remove the motor housing cover.

2. Remove the base and clean the impeller and the volute passage. Do not use strong solvents on the

impeller. Do not remove the impeller.

3. Be sure the impeller turns freely after cleaning.

4. Attach the base to the volute and secure it with the five screws.

Risk of severe injury or death by electrical shock, high temperatures, or

pressurized fluids.

• Always unplug the pump power cord in addition to removing the fuse or shutting off the circuit

breaker before working on the pump or switch.

• Let pump cool for a minimum of 2 hours before attempting to service. Submersible pumps contain

oil that becomes pressurized and hot under normal operating conditions.

Risk of damage to pump or other equipment.

• This unit is permanently lubricated. Oiling is not required. Do not open the sealed portion of the unit

or remove housing screws.

• Do not remove the motor housing cover.

• Do not remove the impeller

• Warranty is void if the motor housing cover, impeller, or seals have been removed. Repairs on the

motor or impeller require special tools.

MAINTENANCE

Troubleshooting

Problem Probable Causes Corrective Action

Pump does not turn on

Pump not plugged in. Plug in pump.

Circuit breaker off or fuse removed. Turn on circuit breaker or replace fuse.

Accumulation of trash on float. Clean float.

Float obstruction. Check float path and provide clearance.

Defective switch. Replace switch.

Defective motor. Replace pump.

Pump will not shut off

Float or float rod obstruction. Check float and float rod path and provide clearance.

Pump is air locked. Remove pump and clean air bleed hole.

Liquid inflow matches pump capacity. Larger pump required.

Defective switch. Replace switch.

Pump runs but does not

discharge liquid

Check valve installed backwards. Check flow indicating arrow on check valve body to ensure

proper installation.

Check valve stuck or plugged. Remove check valve and inspect for proper operation.

Lift too high for pump. Check rated pump performance.

Inlet to impeller plugged. Pull pump and clean.

Pump is air locked. Remove pump and clean air bleed hole.

Pump does not deliver

rated capacity

Lift too high for pump. Check rated pump performance.

Low voltage, speed too slow. Check that supply voltage matches the nameplate rating.

Impeller or discharge pipe is clogged. Pull pump and clean. Check pipe for scale or corrosion.

Impeller wear due to abrasives. Replace pump.

Pump cycles continuously

No check valve in long discharge pipe

allowing liquid to drain back into basin.

Install a check valve in discharge line.

Check valve leaking. Inspect check valve for correct operation.

Basin too small for inflow. Install larger basin.

Water sprays out of a hole

by a bolt on the base of

the unit.

This pump comes with a bleed hole

that allows trapped air to escape from

the pump, preventing air lock.

Water spraying out of this hole is com-

pletely normal.

No corrective action is required.

MAINTENANCE

Replacement parts

Number Part Number Description

1110970101 Cover Assembly, 115 V, Automatic, with Switch, 20' Cord

1 110970102 Cover Assembly, 230 V, Automatic, with Switch, 20' Cord

1 110970103 Cover Assembly, 115 V, Manual, 20' Cord

1 110970104 Cover Assembly, 230 V, Manual, 20' Cord

2 110970201 Capacitor kit, 115 V, with Bracket, Seal Ring

2 110970202 Capacitor kit, 230 V, with Bracket, Seal Ring

3 110970301 Float Assembly with Stem Strap

4 110970401 Volute Base, Plastic, with Gasket

4 110970402 Volute Base, Cast Iron, with Gasket

5 599118 Remote Float Switch, 10' Cord, 115/230 V

5 599210 Remote Float Switch, 20' Cord, 115/230 V

SEWAGE & EFFLUENT 3 YEAR WARRANTY STATEMENT

LIMITED WARRANTY

THIS WARRANTY SETS FORTH THE COMPANY’S SOLE OBLIGATION AND PURCHASER’S EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT.

Franklin Electric Company, Inc. and its subsidiaries (hereafter “the Company”) warrants that the products accompanied by this warranty

are free from defects in materials or workmanship of the Company that exist at the time of sale by the Company and which occur or exist

within the applicable warranty period. Any distributor, sub-distributor, recipient, end-user and/or consumer agrees that by accepting

the receipt of the products, the distributor, sub-distributor, recipient, end user and/or consumer expressly agrees to be bound by the

terms of the warranty set forth herein.

I. Applicable Warranty Period

The products accompanied by this warranty shall be covered by this Limited Warranty for a period of 36 months from the date of original purchase

by the consumer. In the absence of suitable proof of purchase date, the warranty period of this product will begin to run on the product's date of

manufacture.

II. Instructions Applicable to this Limited Warranty

1. Consumers wishing to submit a warranty claim must return the products accompanied by this warranty to the point of purchase for war-

ranty consideration.

2. Upon discovery of a defect, any personal injury, property damage or any other type of resulting damage, if applicable, shall be reasonably

mitigated to the extent possible.

3. At its discretion, the Company may inspect products either at its facilities or in the field, and after determination of a warranty claim, will, at

its option, repair or replace defective parts. Repaired or replaced parts will be returned freight prepaid by the Company.

4. This warranty policy does not cover any labor or shipping charges. The Company shall not be liable for any costs or charges attributable to

any product testing, maintenance, installation, repair or removal, or for any tools, supplies, or equipment needed to install, repair, or

remove any product.

III. Limitations Applicable to this Limited Warranty

THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:

1. Brushes, impeller or cam on models with brush-type motors and/or flex-vane impellers.

2. Any product that is not installed, applied, maintained, and used in accordance with the Company's published instructions, applicable

codes, applicable ordinances and/or with generally accepted industry standards.

3. Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, tampering, acts of God (including light-

ning), acts of terrorism, acts of war, fire, improper storage or installation, improper use, improper maintenance or repair, damage or casu-

alty, or to an excess of the recommended maximums as set forth in the product instructions.

4. Any product that is operated with any accessory, equipment, component, or part not specifically approved by the Company.

5. Use of replacement parts not sold by the Company, the unauthorized addition of non-Company products to other Company products, and

the unauthorized alteration of Company products.

6. Products damaged by normal wear and tear, normal maintenance services and the parts used in connection with such service, or any other

conditions beyond the control of the Company.

7. Any product that has been used for purposes other than those for which it was designed and manufactured.

8. Any use of the product where installation instructions and/or instructions for use were not followed.

9. Products connected to voltage other than indicated on nameplate.

10. Products where the pump was exposed to any of the following: sand, gravel, cement, grease, plaster, mud, tar, hydrocarbons, hydrocarbon

derivatives (oil, gasoline, solvents, etc.) or other abrasive or corrosive substances.

11. Products in which the pump has been used for pumping of liquids above 140 °F.

12. Products in which the pump was allowed to operate dry (fluid supply cut off).

13. Products in which the sealed motor housing has been opened or the product has been otherwise dismantled by customer.

14. Products in which the cord has been cut to a length of less than three feet.

Franklin Electric Co., Inc. | Oklahoma City, OK 73157-2010

800.701.7894 | littlegiant.com

For technical assistance, please contact:

Form 998913 Rev. 003 05/19

The Company reserves the right at any time, and from time to time, to make changes in the design and/or improvements upon its prod-

uct without thereby imposing any obligation upon itself to make corresponding changes or improvements in or upon its products

already manufactured and/or previously sold. The Company further reserves the right to substitute parts or components of substantially

equal quality in any warranty service required by operation of this Limited Warranty.

This written Limited Warranty is the entire warranty authorized and offered by the Company. There are no warranties or representations beyond

those expressed in this document.

THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES INCLUDING WITHOUT LIMITATION, WARRAN-

TIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY SPECIFICALLY DISCLAIMED AND

EXPRESSLY EXCLUDED. CORRECTION OF NON-CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME AS SET FORTH ABOVE,

SHALL CONSTITUTE FULFILLMENT OF ALL LIABILITY OF THE COMPANY TO THE PURCHASER WHETHER BASED ON CONTRACT, NEGLI-

GENCE, OR OTHERWISE.

THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES SUCH AS, BUT NOT LIMITED TO:

DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF USE OF EQUIPMENT, FACILITIES OR SERVICE, LOSS OF PROFIT

OR SALES, COST OF PURCHASES OR REPLACEMENT GOODS, CLAIMS OF CUSTOMERS OF THE PURCHASER, FAILURE TO WARN AND/

OR INSTRUCT, LOSS OF OTHER PRODUCTS, OR COSTS OF ENVIRONMENTAL REMEDIATION, OR DIMINUTION IN PROPERTY VALUE.

THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF THE COMPANY SHALL NOT, EXCEPT

AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCTS UPON WHICH SUCH LIABILITY IS BASED. DAMAGES AS

SET FORTH IN THIS PARAGRAPH SHALL BE REASONABLY MITIGATED TO THE EXTENT POSSIBLE. THIS PARAGRAPH SHALL ALSO

APPLY TO ALL DAMAGES RESULTING FROM CONDITIONS SET FORTH IN SECTION III ABOVE AND (1) DEFECTS IN PRODUCT PROTO-

TYPES OR REPLACEMENT PART PROTOTYPES THAT HAVE NOT BEEN PUT INTO PRODUCTION, CIRCULATED AND SOLD BY THE COM-

PANY, AND/OR (2) DEFECTS THAT WERE NOT FOUND AT THE TIME OF SALE DUE TO SCIENTIFIC AND TECHNOLOGICAL REASONS.

This Limited Warranty gives you specific legal rights. You may have other rights, which vary according to the applicable laws and

regulations. Where any term of this warranty is prohibited by such laws, it shall be null and void, but the remainder of this war-

ranty shall remain in full force and effect.

DISCLAIMER: Any oral statements about the product made by the seller, the Company, the representatives or any other parties, do not

constitute warranties, shall not be relied upon by the user, and are not part of the contract for sale. Seller’s and the Company’s only obli-

gation, and buyer’s only remedy, shall be the replacement and/or repair by the Company of the product as described above. Before

using, the user shall determine the suitability of the product for his intended use, and user assumes all risk and liability whatsoever in

connection therewith.

littlegiant.com

FRANÇAISFR

SÉRIE 6EC & 10EC

Manuel du propriétaire

Pompes de puisard

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ - - - - - - - - 16

INTRODUCTION - - - - - - - - - - - - - 18

Description du produit - - - - - - - - 18

Spécifications - - - - - - - - - - - - 18

INSTALLATION - - - - - - - - - - - - - 19

Installation Physique - - - - - - - - - 19

Branchements électriques - - - - - - 21

TEST DE FONCTIONNEMENT - - - - - - - 22

ENTRETIEN - - - - - - - - - - - - - - - 24

Service Périodique - - - - - - - - - - 24

Dépannage - - - - - - - - - - - - - - 25

Pièces de Remplacement - - - - - - - 26

GARANTIE LIMITÉE - - - - - - - - - - - 27

CONSIGNES DE SÉCURITÉ

Messages d’alertes

CONSIGNES DE SÉCURITÉ

Messages d’alertes

Ce manuel comprend des précautions de sécurité et d’autres ren-

seignements importants présentés dans le format suivant:

IMPORTANT: Présente l’information qui permet un

assemblage et un fonctionnement adéquats du produit.

REMARQUE: Présente de l’information utile ou des précisions.

Ce symbole avise l’utilisateur de la présence d’une ten-

sion dangereuse dans le produit présentant un risque de

blessures ou d’électrocution.

Ce symbole avise l’utilisateur de la présence de surfaces

chaudes présentant un risque d’incendie ou de blessures

corporelles.

Avant de Commencer

L'installation et l'entretien de l'équipement doivent être effectués

par un employé techniquement qualifié. Le non-respect des

codes électriques et codes de plomberie local et national et des

recommandations de Franklin Electric pourrait mener à une élec-

trocution ou un incendie, une mauvaise performance ou une

défaillance de l’équipement.

Soyez consient(e) de l’application, des limites et des risques

potentiels du produit. Lire et suivre attentivement ces instructions

pour éviter toute blessure ou tout dommage matériel. Ne pas

désassembler ou réparer l’unité, sauf si cela est décrit dans le

présent manuel.

Consulter la plaque signalétique du produit pour obtenir des

instructions, précautions et des spécifications de fonctionnement

supplémentaires.

Le non-respect des procédures d’installation/utilisation et de tous

les codes applicables peut entraîner les risques suivants:

Indique une situation dangereuse imminente

qui, si elle n’est pas évitée, entraînera la mort

ou des blessures graves.

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, peut

entraîner la mort ou des blessures graves.

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, peut

entraîner des blessures corporelles mineures

ou modérées.

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, peut

entraîner des dommages à l’équipement ou

matériels.

Risque de mort, de blessure corporelle

ou de dommage matériel en raison

d’une explosion, d’un incendie ou d’une

électrocution.

• Ne pas utiliser pour pomper des liquides inflammables ou

explosifs comme l’essence, le mazout, le kérosène, etc.

• Ne pas utiliser dans une atmosphère explosive ou un

emplacement dangereux selon le Code national de l’élec-

tricité, ANSI/NFPA70.

• Ne pas manipuler une pompe ou un moteur de pompe

avec les mains mouillées ou debout sur une surface

humide ou mouillée, ou dans de l’eau.

• Lorsqu’une pompe est en mode de fonctionnement, ne

pas toucher le moteur, les tuyaux ou l’eau tant que l’unité

n’a pas été débranchée ou déconnectée électriquement.

• Si le dispositif de coupure du circuit d’alimentation se

situe hors site, le verrouiller en position ouverte et le

consigner afin d’empêcher toute mise sous tension

inopinée.

• Si le panneau du disjoncteur n’est pas accessible, con-

tacter la compagnie d’électricité afin que le courant soit

coupé.

CONSIGNES DE SÉCURITÉ

Avant de Commencer

Cette unité contient des hautes tensions

capables de causer de graves blessures

ou la mort par électrocution.

• Pour réduire le risque de choc électrique, débranchez l’ali-

mentation avant de travailler sur le système ou autour de

celui-ci. Plusieurs interrupteurs d’isolement peuvent être

nécessaires pour décharger l’équipement avant de

procéder à son entretien.

• Ce produit est fourni avec un conducteur de mise à la terre

et une fiche munie d’une attache de mise à la terre. Pour

réduire le risque de décharge électrique, assurez-vous de

seulement brancher la pompe à une prise électrique cor-

rectement mise à la terre. Ne retirez pas la troisième

branche de la fiche. La troisième branche sert à la mise à

la terre de la pompe, afin de prévenir tout risque possible

de décharge électrique. N’utilisez pas un cordon de ral-

longe.

• Vérifier les prises électriques à l’aide d’un analyseur de

circuit pour s’assurer que les fils de phase, de neutre et de

terre sont correctement branchés. Si ce n’est pas le cas, le

problème doit être corrigé par un électricien qualifié

agréé.

• Raccorder le système de pompe en respectant la tension

indiquée.

• La pompe a été évaluée pour être utilisée avec de l’eau

uniquement. La pompe doit être utilisée uniquement avec

des liquides compatibles avec les matériaux de ses com-

posants. Si la pompe est utilisée avec des liquides incom-

patibles avec les composants de la pompe, le liquide peut

provoquer une défaillance du système d'isolation élec-

trique entraînant un choc électrique.

Risque de dommages à la pompe ou d’autres

équipements.

• Ne pas utiliser la pompe pour pomper de l’eau de mer, des

boissons, de l’acide, des solutions chimiques ou tout autre

liquide qui favoriserait la corrosion, ce qui pourrait

endommager la pompe.

• Ne pas faire tourner la pompe à sec. Pour obtenir un

refroidissement optimal et pour prolonger la durée de vie

de la pompe, le niveau de liquide pompé doit

normalement dépasser le dessus du boîtier de la pompe.

• Cette pompe n’est pas prévue pour être utilisée dans un

étang.

Risque de blessures corporelles

ou de dommages matériels.

• Cet équipement ne doit pas être utilisé par des enfants ou

des personnes ayant des capacités physiques, sensori-

elles ou mentales réduites ou un manque d’expérience, à

moins qu’elles ne soient supervisées ou dirigées. Les

enfants ne doivent pas utiliser l’équipement ni jouer avec

le produit ou à proximité de celui-ci.

• L’équipement peut démarrer automatiquement. Toujours

débrancher le cordon d’alimentation de la pompe et

couper l’alimentation électrique avant d’entretenir la

pompe ou l’interrupteur.

• Une pompe inopérante ou défectueuse pourrait entraîner

une inondation, des blessures corporelles ou des dom-

mages matériels.

• Dans les applications où des dommages matériels et/ou

des blessures corporelles pourraient découler du non-

fonctionnement ou d’une fuite de la pompe en raison de

pannes de courant, d’une obstruction de la ligne d’évacu-

ation ou de toute autre raison, un système de sauvegarde

automatique et/ou une alarme doivent être installés.

• Ne pas faire fonctionner la pompe à sec. En cas de

fonctionnement à sec, la température à la surface de la

pompe augmentera à un niveau susceptible de causer

des brûlures cutanées en cas de contact et entraînera de

graves dommages à votre pompe.

• Ne pas graisser le moteur. Le carter moteur de la pompe

est scellé et renferme une huile diélectrique de qualité

supérieure pour la transmission de chaleur et la lubrifica-

tion à vie. L’utilisation d’autres huiles peut causer de

graves électrocutions et/ou des dommages permanents

de la pompe.

• Le fonctionnement de cet équipement requiert les

instructions d’installation et de fonctionnement détaillées

fournies dans le présent manuel. Lire tout le manuel

avant d’installer et d’utiliser le produit.

• L’utilisateur final doit recevoir et conserver le manuel

pour consultation ultérieure.

• Garder les étiquettes de sécurité propres et en bon état.

• Garder la zone de travail propre, bien éclairée et dégagée.

• Porter des lunettes de sécurité lors de l’installation ou de

l’entretien de la pompe.

• Ne pas porter de vêtements amples, de bijoux ou tout

autre accessoire qui pourrait se prendre dans les pièces

mobiles de l’équipement. Attacher les cheveux longs et

retirer les bijoux.

INTRODUCTION

Description du produit

INTRODUCTION

Description du produit

Cette pompe immergée est prévue pour être utilisée dans des bassins ou des stations de relèvement. Elle peut être

utilisée pour pomper de l’eau claire ou des effluents eau grise contenant des semi-solides de forme sphérique jusqu’à

12,7mm (1/2po) de diamètre. Ne pas utiliser cette pompe dans des applications où d’autres débris (gravier, sable,

débris flottants, etc.), des abrasifs ou des matières corrosives sont présents.

Ce produit a été soigneusement testé, inspecté et emballé pour en assurer la livraison et le fonctionnement sécu-

ritaires. Veuillez examiner votre ou vos articles soigneusement afin de vous assurer qu’aucun dommage ne s’est pro-

duit pendant l’expédition. Dans le cas contraire, veuillez communiquer avec le vendeur. Il vous aidera à obtenir un

remplacement ou une réparation, le cas échéant.

Le moteur de la pompe est muni d’un protecteur thermique à réinitialisation automatique et peut redémarrer subite-

ment. Le déclenchement du protecteur est une indication que le moteur est surchargé ou surchauffe, ce qui peut être

causé par des problèmes d’application, comme un impulseur de pompe obstrué, un interrupteur coincé en position

de mise en marche, une pompe qui fonctionne à vide, une pompe bloquée par de l’air, un cycle court de pompe, une

alimentation à tension excessivement élevée ou faible, ou possiblement la fin de la durée de vie utile d’une pompe,

d’un moteur, de paliers ou d’un joint d’étanchéité.

Spécifications

Gallons par minute, à la hauteur/Litres par minute, à la hauteur

La taille 5 pieds

1.5 mètres

10 pieds

3 mètres

15 pieds

4.5 mètres

20 pieds

6.1 mètres

30 pieds

9.1 mètres Coupure

6EC 53 GPM 50 GPM 42 GPM 34 GPM –28 pieds

8.5 mètres

201 LPM 189 LPM 159 LPM 129 LPM

10EC 67 GPM 57 GPM 47 GPM 42 24 GPM 36 pieds

11 mètres

254 LPM 216 LPM 178 LPM 159 LPM 91 LPM

INSTALLATION

Installation Physique

INSTALLATION

Installation Physique

1. La pompe doit être installée dans un bassin étanche au gaz approprié d’au moins 18 po (45,7 cm) de diamètre et

24 po (61,0 cm) de profondeur, et ventilé conformément aux codes locaux de plomberie.

2. Enlevez tout débris dans le bassin et placez la pompe au centre de ce dernier (se référer à “Installation Typique”

à la page 20). Un fond solide empêchera la pompe d’être obstruée par du sable et des saletés.

3. La pompe doit être placée sur une surface dure et de niveau. Ne placez jamais la pompe directement sur une sur-

face d’argile, de terre ou de gravier. Ces surfaces comportent de petites roches, du gravier, du sable, etc., qui

peuvent obstruer ou endommager la pompe et provoquer sa défaillance.

4. N’essayez pas de restreindre le côté prise de ces pompes. La restriction de la prise peut endommager le joint

d’étanchéité et sous-alimenter la pompe. S’il est nécessaire de réduire les débits, une soupape peut être installée

sur le côté refoulement de la pompe. Ou si un tuyau flexible en vinyle est utilisé, une bride peut être utilisée sur le

tuyau pour restreindre le débit.

5. Connectez la tuyauterie de refoulement. Utilisez une pâte à joint de tuyau sur toutes les connexions. Le tuyau de

refoulement doit être aussi court que possible et comporter le moins de coudes possible. Le tuyau de

refoulement doit être du même diamètre que celui du refoulement, afin de réduire les pertes par frottement. Un

tuyau plus petit restreint la capacité et réduit le rendement de la pompe. La pompe d’égout est livrée avec un

refoulement à filetage femelle de 1.5 po (38 mm).

• Soutenez la pompe et la tuyauterie au cours de l’assemblage et de l’installation. Un manquement pourrait

entraîner la rupture des tuyaux, la défaillance de la pompe, la défaillance des paliers du moteur, etc.

• Installez toujours un raccord union dans le conduit de refoulement, juste au-dessus du couvercle de bassin,

afin de permettre le retrait facile de la pompe à des fins de nettoyage ou de réparation.

6. Un clapet anti-retour doit être utilisé dans le conduit de refoulement pour empêcher un refoulement du liquide

dans le bassin. Le clapet anti-retour doit être une vanne à débit direct qui laisse facilement passer les solides.

Risque de blessure grave ou de mort par électrocution.

• Débranchez toujours l’alimentation électrique avant de toucher à la pompe ou au refoulement.

• Avant l’installation, vérifiez les codes locaux de l’électricité et du bâtiment. L’installation doit

respecter leur réglementation, de même que le plus récent Code national de l’électricité (CNE).

Risque de dommages matériels dus aux inondations.

• N’installez pas le clapet antiretour en position verticale, car des solides peuvent se déposer dans le

clapet d'et empêcher le clapet d'ouverture au moment du démarrage. Pour un rendement optimal

du clapet anti-retour dans la gestion des solides, installez dans une position horizontale ou à un

angle d’au plus 45°.

• Lorsqu’un clapet anti-retour est utilisé, percez un orifice de sûreté (de 1/8 po ou 3/16 po [3,2 mm ou

4,8 mm] de diamètre) dans le tuyau de refoulement. Cet orifice doit être situé sous le niveau du

plancher, entre le refoulement de la pompe et le clapet anti-retour. Si un tel orifice de sûreté n’est

pas percé, la pompe peut être « bloquée par de l’air » et ne pas pomper d’eau, même si elle est en

marche.

INSTALLATION

Installation Physique

7. Fixez les cordons d’interrupteur et de pompe au conduit de refoulement avec du ruban d’électricien. Cela aidera

à protègera le cordon de tout dommage.

8. Testez le fonctionnement du système en suivant les instructions présentées dans “Test de fonctionnement” à la

page 22 de ce manuel. Ne tentez pas de faire fonctionner la pompe sans eau; cela endommagerait les joints

d’étanchéité et les paliers, et risquerait de provoquer des dommages permanents à la pompe.

9. Placez le couvercle par-dessus le bassin. Ce couvercle aide à empêcher des débris d’entrer dans le bassin et

protège contre les blessures accidentelles.

Installation Typique

Page is loading ...

Little GIANT 506858 Owner's manual

Brand: Little GIANT

Model: 506858

Category: Water pumps

Type: Owner's manual

Download PDF

report

in other languages

français: Little GIANT 506858 Le manuel du propriétaire
español: Little GIANT 506858 El manual del propietario

Little GIANT 506858 Owner's manual

Little GIANT 506858 Owner's manual

in other languages

Related papers

Other documents