Sherpa 582040 User manual

Brand
Sherpa
Model
582040
Type
User manual

Sherpa 582040 allows you to mount your Rotopax containers securely to your window panel. It features vibration dampening plugs to protect your gear and the panel while on rough terrain. The mount installs easily and is compatible with Standard/DLX/LOX Rotopax mounts. Whether you're heading out for a weekend camping trip or a cross-country adventure, the Sherpa 582040 is the perfect way to transport your fuel or water.

Sherpa 582040 allows you to mount your Rotopax containers securely to your window panel. It features vibration dampening plugs to protect your gear and the panel while on rough terrain. The mount installs easily and is compatible with Standard/DLX/LOX Rotopax mounts. Whether you're heading out for a weekend camping trip or a cross-country adventure, the Sherpa 582040 is the perfect way to transport your fuel or water.

WINDOW PANEL
ROTOPAX MOUNT
INSTALL INSTRUCTIONS
REV.1
44
1/4”-20 Nylock nut 1/4” Washer
Before you start
HARDWARE CHECKLIST
Exact hardware color counts may vary based on the options selected at checkout.
4
Vibration dampers
4
1/4”-20 Hex bolt
(5/8”)
It is suggested that all accessories are
installed while the window panel is o
of the vehicle. This makes the process of
positioning and fastening the accessory
much easier.
Setup
Required Components:
4x Rotopax carriage bolts
4x Rotopax flat washers
4x Rotopax nylock nuts
1x Rotopax Standard/DLX/LOX
If the bottom mounting plate supplied
with all standard/DLX/LOX Rotopax
mounts is not already installed, do
so using the 2x M8 x 12mm bolts
supplied by Rotopax.
Assembly 01
Required Components:
4x 1/4”-20 x 5/8” Hex bolt
4x 1/4” Flat Washers
4x Nylock nuts
Secure the rotopax assembly to the
window panel using the supplied hex
bolts, nuts, and flat washers. Each bolt
should sit at the ends of the X-pattern
on the window panel. Note that the bolts
should be run through the back side of
the panel so that the excess threads point
away from the glass. This is important
for maximizing the clearance between
the window panel components and the
window.
Back view
Assembly 02
Slide the Rotopax container over the
base and screw the supplied handle in
to secure the Rotopax container.
Front view
Assembly 03
Once the Rotopax container is
situated, lift it back o of the panel
slightly and install the supplied
vibration dampening plugs through
the slots in the four corners of contact
between the container and the panel.
Assembly 04
Repeat the installation process in
the two outer Rotopax mounting
locations on the panel if you plan to
use 2x 2 gallon containers, or 1x 4
gallon container.
EXPLORE.
All products built and designed by Sherpa Equipment Company are intended for
o-road use and should be assembled, installed, and used according to Sherpa
Equipment Company’s recommendations. Sherpa Equipment Companies products
should be used safely with good judgment towards others and surroundings.
By installing Sherpa Equipment Companies products on your vehicle you assume
all liability. Sherpa Equipment Company will not be held liable for damages or loss
associated with the installation or use of its products. It is recommended that you
inspect your roof rack within the first 100 miles of installation and every 500 miles
after.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Sherpa 582040 User manual

Brand
Sherpa
Model
582040
Type
User manual

Sherpa 582040 allows you to mount your Rotopax containers securely to your window panel. It features vibration dampening plugs to protect your gear and the panel while on rough terrain. The mount installs easily and is compatible with Standard/DLX/LOX Rotopax mounts. Whether you're heading out for a weekend camping trip or a cross-country adventure, the Sherpa 582040 is the perfect way to transport your fuel or water.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents