Front Runner RRAC112 Installation guide

Brand
Front Runner
Model
RRAC112
Type
Installation guide
RRAC106_REV_A03 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
front runner
RRAC106
ENG
1
Thank you for purchasing Runner Rotopax Side Mount Brackets.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
ROTOPAX SIDE MOUNT BRACKETS
RRAC106_REV_A03 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
7
1 2 X RotoPax Side Mount Brackets
2 2 X Support Bracket - 48mm Wide
3 4 X M8x20 Button Head
4 6 X M8x16x1.6 Flat Washer
5 6 X M8 Nyloc Nut
6 2 X M8x20 Hex Bolt
7 2 X M8 Nut Cap
5
4
3
2
6
5
1
10mm
13mm
4mm
5mm 13mm
RRAC106_REV_A03 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.1
2.2
2.3
Ensure that one of the RotoPax side mount
brackets are aligned with a slat.
Slide four M8 nyloc nuts (Item 5) in the side
profile as shown in 2.12.
Secure the RotoPax side mount brackets as
shown in 2.1.
Fit 2 RotoPax RX-PM mounts to the RotoPax
mounting plate (RRAC157). Fasteners are
supplied with the RotoPax RX-PM pack
mounts
Fit the Rotopax mounting plate to the
Rotopax side mounting brackets. Move
the side mounting brackets to the desired
position before fully tightening all the
fasteners.
The brackets angles and height can be
adjusted to suit the vehicle.
RotoPax RX-PM Pack mounts
RRAC157
R
7
5
4
2
5
3
1
1
13mm
13mm
13mm
13mm
5mm
RRAC106_REV_A03
4
FIT AND SECURE
2
2.4
2.1
2.4
Place the Rotopax over the RotoPax RX-PM
Pack mounts and thighten.
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
© 2021FRONT RUNNER VEHICLE OUTFITTERS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Front Runner RRAC112 Installation guide

Brand
Front Runner
Model
RRAC112
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents