2. iLight
  3. Plexineon Recessed Static Color
Plexineon Recessed Static Color

iLight Plexineon Recessed Static Color User manual

  • Hello! I am an AI chatbot trained to assist you with the iLight Plexineon Recessed Static Color User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation Instructions - Plexineon Recessed Static Color
Models: Plexineon Fixture Recessed Mount Static Color
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. RECESSED MOUNT ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV0.1
10252022
1 / 6
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Installation Instructions - Plexineon Recessed Static Color
Models: Plexineon Fixture Recessed Mount Static Color
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. RECESSED MOUNT ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV0.1
10252022
2 / 6
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
1.1 Screw end plate onto extrusion housing.
1
1.1
extrusion housing
end plate
screw
NOTE: Prior to installation all 24VDC wires must be present within 72” of the installation. Refer to the power supply
installation instruction for additional information.
NOTE: More than one person is recommended for this installation.
2
2.1 If more than one extrusion housing, use two alignment pins to connect both side of the extrusion housing.
2.1
extrusion housing extrusion housing
alignment pin
Installation Instructions - Plexineon Recessed Static Color
Models: Plexineon Fixture Recessed Mount Static Color
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. RECESSED MOUNT ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV0.1
10252022
3 / 6
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
INSTALLATION OPTIONS
extrusion housing extrusion housing
paint mask
plaster plate
NOTE: Use paint mask to protect extrusion housing when doing a surface/
wall finishing. Install plexineon fixtures after removing paint mask NOTE: Use plaster plate when doing a mud-in installation. Use paint mask to
protect extrusion housing during surface/wall finishing.
INSTALLATION OPTIONS NOTE: Blocks are provided by others.
dry wallextrusion housing
blocks
fixture support
dry wall
extrusion housing
plaster plate mud-in
Wood Blocking Installation Mud-in Installation
Installation Instructions - Plexineon Recessed Static Color
Models: Plexineon Fixture Recessed Mount Static Color
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. RECESSED MOUNT ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV0.1
10252022
4 / 6
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
3.1 Drill or punch Ø 5/8” hole into extrusion housing.
3.2
3.3
Clamp powerfeed strain relief to wire.
Snap powerfeed strain relief into hole.
3.1
3.2
33.3
5/8”
extrusion housing
powerfeed strain relief
powerfeed wire
snap
powerfeed strain relief
4
4.1 Install recessed mounting clips to fixture. Make sure they are approximately 30” apart.
4.2 Use gule to fill in all gaps between recessed mounting clips and plexineon fixture.
GLUE
30”
recessed mounting clip
plexineon fixture
glue
NOTE: Drill hole on extrusion housing before install into wall/surface.
4.1 4.2
Installation Instructions - Plexineon Recessed Static Color
Models: Plexineon Fixture Recessed Mount Static Color
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. RECESSED MOUNT ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV0.1
10252022
5 / 6
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
4.1 Peel back power cord to expose wires.Connect power supply wires to fixture wires. Waterproof wire nuts recommended in this step.
4.2 Snap plexineon fixture with glued mounting clips into extrusion housing.
3.1
4powerfeed strain relief
extrusion housing
plexineon fixture
powerfeed wire
recessed mounting clip
extrusion housing
waterproof
wire nuts
3.2
Installation Instructions - Plexineon Recessed Static Color
Models: Plexineon Fixture Recessed Mount Static Color
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. RECESSED MOUNT ONLY
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV0.1
10252022
6 / 6
5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
to Plexineon
Plexineon xture Plexineon xture Plexineon xture
Multiple Fixtures
5.1 Connect +24 VDC strip color from
the Plexineon to the power supply
+24 VDC red wire.
Connect -24 VDC solid color wire
from the Plexineon to power supply
-24 VDC black wire.
5.1
/