Elvox 6621 Operating instructions

Brand: Elvox

Model: 6621

Category: Telephones

Type: Operating instructions

Installation and operation manual

Interphones and monitors for Two-Wire Elvox systems

RESET

INDEX

Monitor series TAB Pag. 4

type 7529, 7529/D

Interphone series TAB Pag. 10

type 7509, 7509/D

Interphone series PETRARCA Page 15

type 6209

Monitor series PETRARCA Page 18

type 6029 - 6029/C

Monitor series Giotto 6300 Page 19

type 6329, 6329/C

Interphone series 8870 Page 23

type 8879

Monitor series 7200 Page 26

type 7211

Monitor series 6600 Page 31

type 6621, (6621/F), 6611, (6611/F) flush-mounted version

type 662C, (662C/F), 661C , (661C/F) table version

type 6721, (6721/F), 6711, (6711/F) surface wall-mounting version

RESET

Interphone series 6900 Page 39

Art. 6901, 6901/D

Interphone series 6600 Page 35

type 6601/AU, (6601/AUF), 6611/AU, (6611/AUF) flush-mounted version

type 660C/AU, (660C/AUF), 661C/AU, (661C/AUF) table version

type 6701/AU, (6701/AUF), 6711/AU, (6711/AUF) surface wall-mounting version

ID list and respective secondary (video)interphones Due Fili Elvox (Two Wire Elvox) Page 44

Bus termination for elvox two-wire installations Page 45

Tab series monitor for Due Fili Elvox (Two-Wire Sy-

stems)

Art. 7529, 7529/D*

Fig. 1.1

E2 E3

Description

Monitor made of thermoplastic material with handset and 3.5” LCD colour

display. Equipped with four buttons for the main video door entry functions:

door lock release, self-start, auxiliary services (stair light), ringtone muting

and 4 programmable supplementary keys that can execute up to 4 auxiliary

functions or intercommunicating calls.

The following settings can be made: ringtone volume, ringtone muting when

“User Away” function is activated and ringtone type selection. Option of

setting different ringtones for calls made from different points, e.g.: outdoor

entrance panel, door call, intercommunicating call.

LED signalling of “door/gate open” and “Unanswered calls” (up to 4 calls

with monitor in ringtone muted state).

For use in Elvox Two-Wire systems with power supply 6922.

Article 7529/D has a hearing aid function.

Before commencing programming, read the instructions carefully to

get a clear idea of the product’s characteristics, functions and featu-

res.

Technical characteristics

• Surface-mounted monitor made of ABS with mirror gloss finish on front

panel.

• Designed for external wall mounting with metal coupling plate or fitting

to a box (can be mounted directly on the wall using wall plugs or to a

Vimar V71303 type unified 3-module rectangular flush-mount back box

or a 60 or 70 mm round flush-mount back box).

• 3.5” LCD display.

• Touch-sensitive keys with backlit symbols (during operation).

• Power supply from Two-Wire Bus

• Input current:

- on standby: 7mA

- maximum conversation current: 150mA

- peak current limited to call time: 200mA

• Operating temperature: 0° ÷ 40°C

• Electronic chime: different ringtones for panel call, intercom call and

door call.

• 10 different ringtones can be selected.

• Output for additional chime 860A or relay 0170/101.

• Input for door call.

• Input for additional power supply (type 6923).

• Monitor 7529 dimensions: 160x180x45 mm

A Self-start: for self-start/auto-activation of interphone (to

Master entrance panel by default).

B Ringtone muting: Mutes ringtone during call.

C Door lock: Lock opening command (programming can be

adjusted using the programmer).

D Auxiliary 1 (Stair light): For auxiliary service (actuator 1 of

relay 69RH or 69PH activated by default).

E1 Button 1: Programmable button to activate auxiliary ser-

vice or intercommunicating call (actuator 2 of relay 69RH or

69PH activated by default).

E2 Button 2: Programmable button to activate auxiliary ser-

vice or intercommunicating call.

E3 Button 3: Programmable button to activate auxiliary ser-

vice or intercommunicating call (entrance panel function F1

activated by default, the last entrance panel to make a call).

E4 Button 4: Programmable button to activate auxiliary ser-

vice or intercommunicating call (entrance panel function F2

activated by default, the last entrance panel to make a call).

Buttons

RESET

E+

E-

12V

50Ω

100Ω

OPEN

PROG

Fig. 1.2

Dip-switch for Bus termination

Connection terminal block

Connection terminal block:

1, 2 Two pairs of terminals for Two-Wire bus

E+, E- Additional power supply for monitor with power supply unit type

6923.

12V Connection of additional chime (positive reference 12V).

CH Connection of additional chime (call repetition).

FP Input for door call button (with reference to terminal M).

M Earth reference.

B During normal operation:

- Flashing light: indicates that the interphone is receiving

a call (from outdoor entrance panel or from an intercom-

municating device).

- Steady light: ringtone muted (User Away function).

- Steady light flashing every 10s: if calls have been

made from the entrance panel while the ringtone was

muted, the LED flashes a number of times equal to the

number of calls received from the entrance panel (up to

4 calls are memorised). The flash log is reset when the

ringtone volume is restored.

During programming:

- Flashing light: indicates programming mode.

C During normal operation:

- Steady light: indicates that the door is open if the sen-

sor has been installed on at least one entrance panel

and connected between terminals PA and M.

During adjustment:

- Flashing light: indicates that ringtone selection or vo-

lume adjustment is in progress.

Signals:

Settings

H Brightness setting: allows the screen brightness to be

adjusted.

I Contrast setting: allows contrast to be adjusted.

L Colour setting: allows the colour to be adjusted.

Hearing aid function (art. 7529/D only)

Art. 7529/D has an internal coil which allows hearing aid wearers to use the

device. In this operating mode, the hearing aid must be switched to the

“T” position. However, for correct operation of the hearing aid refer to its

instruction manual.

Note: metal objects or electronic equipment in the vicinity may affect the

quality of the sound received by the hearing aid.

Operation

Important: For the monitor to work, the ID must have already been pro-

grammed. To check this, press any of the monitor buttons. If an ID has been

assigned to the monitor, a beep will sound when a button is pressed; if no

ID has been assigned or it has been deleted, a triple beep will sound.

Operating times

The answer and conversation times depend on the configuration of the cor-

responding entrance panel parameters (to change these times, please refer

to the electronic entrance panel unit instructions).

- Answer time (for entrance panel call): Default value 30 s

(minimum value 1 s, maximum value 255 s)

- Answer time (for intercommunicating call): 30 s (fixed value)

- Conversation time (for entrance panel call): Default value 120 s

(minimum value 10 s, maximum value 2550 s)

- Conversation time (for intercommunicating call): Default value 5 minutes

(can be modified to unlimited time).

Answering a call

A call from the outdoor entrance panel or from an intercommunicating de-

vice can be answered during the chime cycle or once it has ended. To an-

swer, lift the handset; to end the call, replace the handset.

Receiving a door call

The monitor can receive calls from a door call button if connected to termi-

nals M and FP directly or via interface 6120 (see wiring versions).

When the door call button is pressed, the monitor emits a different tone to

the one used for outdoor entrance panel calls or intercommunicating calls.

To stop the chime, lift the handset.

In the case of a door call by means of a button connected directly to the

monitor’s terminals FP and M; chime cycle duration depends on how long

the button was held down (max. 10 s)

Making an intercommunicating call

To make a call to another indoor unit, one or more buttons must have been

programmed (see “Button programming” section).

To make the call, press the button programmed for the relevant indoor unit.

During the call, the monitor emits a tone in order to signal that the call is

being made. If the interphone/monitor is already engaged in another call, a

tone will be heard on the monitor making the call to indicate that the user

receiving the call is busy.

When the indoor unit receiving the call answers, communication begins au-

tomatically. Replace the handset to end the conversation.

The maximum conversation time is 5 minutes (default).

Muting the ringtone during a call (Mute function)

When receiving a call from an outdoor entrance panel or from an intercom-

municating device or a door call via device 6120, the call ringtone can be

muted by pressing button B.

Door lock command

Press the lock button (with the handset hooked on or in conversation) to

send a lock opening command to the entrance panel (by default, the last

entrance panel to make a call).

Self-start

- Self-start with dedicated button (button A):

to use the self-start function and communicate with the master entrance

panel, briefly press button A (self-start) to turn on the monitor and lift the

handset to start the conversation. Replace the handset to end the con-

versation.

- Self-start with programmed button to a specific panel:

to use the self-start function and communicate with a specific entrance

panel, press and release the button programmed to call that entrance

panel (see “Programming the self-activation/self-start button to a spe-

cific panel ” section).

Calling a porter switchboard

To call a porter switchboard (if present in the system): lift the handset and

press button C (lock) to make the call.

E+

E-

12V

50Ω

100Ω

OPEN

Dip-switch for

Bus termination

Fig. 1.4

100Ω

50Ω

Fig. 1.3

OPEN

Configurations

Choice of ringtones

10 different ringtones can be selected. Different ringtones can also be set

for outdoor, intercommunicating and door calls (see below). The ringtones

must be selected with the monitor on stand-by and the handset on the

hook.

The button for entering configuration mode is button A (self-start).

Button E1 selects the ringtone for ENTRANCE PANEL CALL.

Button E2 selects the ringtone for INTERCOMMUNICATING CALL.

Button E3 selects the ringtone for DOOR CALL (exclusively using the but-

ton interface module 6120 or Vimar landing call button). In the case of a

door call by means of a button connected directly to the monitor’s termi-

nals FP and M, the ringtone cannot be changed.

Configuration:

1) Press button A (self-start) and hold down (for 2 s) until the LED C (lock)

begins flashing and the monitor emits an audible signal.

2) Press and hold down the button for the chosen ringtone (button

E1/button E2/button E3) until the ringtone is heard on the monitor.

3) Press the button repeatedly (button E1/button E2/button E3) to select

the desired type of ringtone.

4) After choosing the desired ringtone, press button A or refrain from tou-

ching any buttons for 5s to save. After completing the configuration,

the LED flashes and then turns off.

Ringtone volume adjustment

The ringtone volume can be set to 6 levels plus mute.

Press button A (self-start) to enter configuration mode.

Press button B (bell) to lower the ringtone volume.

Press button C (key) to increase the ringtone volume.

The ringtone volume must be adjusted with the monitor on stand-by and

the handset on the hook.

Configuration:

1) Press button A and hold down (for 2 s) until the LED C (lock) begins fla-

shing and the monitor emits an audible signal.

3) Press button B to lower or button C to increase the volume. Each time

the buttons are pressed the volume changes by one level.

4) After choosing the desired volume, press button A or refrain from tou-

ching any buttons for 5s to save. After completing the configuration,

the flashing LED goes off and a “beep” is emitted.

Muting the ringtone (User Away function)

Using the volume adjustment procedure described above, pressing button

B a sufficient number of times results in the ringtone being muted. The

“Ringtone muted” status is indicated by the button B LED (ringtone muted)

lighting up steadily.

If the monitor receives a call from the entrance panel while the ringtone is

muted, this is indicated by the LED/button B emitting one flash for each

unanswered call up to a maximum of 4 calls (these flashes occur every 10

s). When the ringtone volume is restored, at least to its minimum level, this

indication will be reset.

Maintenance

Clean the monitor using a soft cloth, which can be dry or slightly dampe-

ned with water. Do not pour water directly onto the screen and do not use

any type of chemical product.

Bus termination for video signal stabilisation

The BUS termination dip-switches for video signal stabilization are located

in the rear of the monitor, near the terminal block.

Depending on the connection configuration (interphones/monitors connec-

ted in series or derived from a distributor), set the dip-switches in the ap-

propriate position (position A, B or C) according to the instructions given in

the note “Bus termination for ELVOX TWO-WIRE INSTALLATIONS” in the

wiring diagrams section below.

Manual programming

Basic interphone/monitor programming is as follows:

- Programming ID, which must be performed on the monitor that recei-

ves the call individually or on the first monitor of a group of interpho-

nes/monitors with simultaneous calls (master interphone/monitor).

- Programming secondary ID, which must be done for interpho-

nes/monitors associated with a master interphone/monitor.

- Programming programmable buttons or changing the default setting

of supplementary buttons, for auxiliary services or intercommunicating

calls.

Programming must be carried out with the system switched on, without

active communication and only after the interphones/monitors have been

connected to the system and the entrance panels have been programmed.

N.B.: all the programming or deletion phases must be performed with the

interphone/monitor handset lifted and held against the user’s ear.

Programming ID identification code

The identification code is programmed by means of a main entrance panel

(MASTER), already configured and present in the system.

The monitor is supplied without associated identification code. To verify

this, press the lock release button and the monitor should emit an audible

signal (triple beep).

To program the ID, proceed as follows:

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED B

(ringtone mute) begins flashing.

3) Release the buttons.

4) Press button C and hold it down (for 2 sec.) until the handset emits an

audible signal and communication between the monitor and the out-

door entrance panel begins.

5) Release button C.

Important: you will have 5 s in which to press button C (as indicated in

step 4). If button C is not pressed within the 5 s, steps 1, 2 and 3 must

be repeated.

6) You now have approx 30 seconds to assign the ID code of the external

entrance panel:

- in the case of an alphanumeric panel, key in the primary ID and press

the “bell” button to confirm.

- in the case of a push-button entrance panel, press the button you want

to use to call the monitor.

Important: If the system already contains an interphone/monitor with the

same associated identification code, the entrance panel emits a low tone

and the process must be repeated from the start in order to assign a diffe-

rent code.

Programming secondary ID

Programming the secondary ID is only necessary when you want more than

one monitor to ring in response to the same pushbutton or call code. The

monitors that are to ring at the same time are associated with the same

group. The “master” monitor is programmed first by means of the “identi-

fication code programming” procedure described above, while the addi-

tional group monitors are programmed with the secondary identification

code.

The maximum number of monitors that can be associated with the same

group without using a 950C programmer is 3 plus a master unit.

Alternatively, a 950C programmer or SaveProg software can be used to

program activation of the ringtone of all Monitors and the monitor of only

the master unit. Before answering from a secondary audio/Monitor, the re-

levant monitor can be turned on by means of the self-start button.

To program the secondary ID, proceed as follows:

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED B

(ringtone mute) begins flashing.

3) Release the buttons.

4) Press buttons A and C simultaneously and hold them down (for 2 sec.)

until the handset emits an audible signal and communication between

the monitor and the outdoor entrance panel begins.

5) Release buttons A and C.

Important: you will have 5 s in which to press buttons A and C (as in-

dicated in step 4). If buttons A and C are not pressed within the 5 s,

steps 1, 2 and 3 must be repeated.

6) You now have approx 30 seconds to assign the ID code of the external

entrance panel:

- in the case of an alphanumeric panel, key in the primary ID and press

the “bell” button to confirm.

- in the case of a push-button entrance panel, press the button you want

to use to call the monitor.

Important: When programming the primary and secondary ID, the monitors

undergoing programming automatically acquire a code that depends on

the association with the button or code used to call the outdoor entrance

panel. Correspondence between the primary ID and the respective secon-

dary ID codes is provided in the table below.

Example: If ID = 8 is given to a second interphone/monitor, the automatic

second interphone/monitor identification attribution procedure will automa-

tically assume ID = 72 (see table).

When a call is made to ID = 8, both monitors/interphones will chime and

both can be used to answer. If, on the other hand, in the case of an alpha-

numeric panel you enter 72 (the ID automatically assigned by the proce-

dure), a chime is emitted by the interphone/monitor for which the secondary

ID assignation procedure was carried out and only this interphone can be

used to answer the call.

Table of primary and corresponding secondary ID codes:

Important: to delete from a group, the programming deletion procedure

described in the “Default data restore procedure” section must be perfor-

med.

Button programming

Important: without programmer 950C or SaveProg software, the only fun-

ctions that can be assigned are intercommunication, specific entrance

panel self-activation, restoring buttons programmed by the installer to their

default settings and restoring default data.

Primario

ID Secondario

1 2 3

26 126 127 128

27 129 130 131

28 132 133 134

29 135 136 137

30 138 139 140

31 141 142 143

32 144 145 146

33 147 148 149

34 150 151 152

35 153 154 155

36 156 157 158

37 159 160 161

38 162 163 164

39 165 166 167

40 168 169 170

41 171 172 173

42 174 175 176

43 177 178 179

44 180 181 182

45 183 184 185

46 186 187 188

47 189 190 191

48 192 193 194

49 195 196 197

50 198 199 200

Primario

ID Secondario

1 2 3

1 51 52 53

2 54 55 56

3 57 58 59

4 60 61 62

5 63 64 65

6 66 67 68

7 69 70 71

8 72 73 74

9 75 76 77

10 78 79 80

11 81 82 83

12 84 85 86

13 87 88 89

14 90 91 92

15 93 94 95

16 96 97 98

17 99 100 101

18 102 103 104

19 105 106 107

20 108 109 110

21 111 112 113

22 114 115 116

23 117 118 119

24 120 121 122

25 123 124 125

Button programming procedure for intercommunicating calls

To program the buttons, proceed as follows:

1) Press the “talk/listen” button or lift the handset (depending on model

installed) for the interphone/monitor TO BE CALLED.

2) Lift the handset to be programmed (the caller handset).

3) Press buttons B and A on the monitor to be programmed (caller) simul-

taneously and hold them down until LED B (ringtone mute) begins fla-

shing.

4) Release buttons B and A.

5) Press and hold down the button to be programmed (e.g. E1, E2, E3, E4).

6) Wait until the monitor handset emits a continuous tone.

7) Release the button to be programmed on the caller monitor.

8) Press a button (lock/F1/F2) on the interphone/monitor to be called.

9) An audible signal in the handset of the (caller) monitor being program-

med confirms that the procedure has been completed correctly.

Procedure for restoring default data for each individual button

(E1, E2, E3, E4)

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED B

(ringtone mute) begins flashing.

3) Release buttons B and A.

4) Press and hold down the button you want to return to default program-

ming (not valid for Self-start and Lock buttons).

5) Wait until the monitor handset emits an audible signal.

6) Release the button.

7) Press the button again to confirm. The monitor handset will again emit

a signal. The button has now been restored to its default value.

Important: This procedure can be used to manually reprogram all buttons

with the exception of the lock and self-start buttons, for which programmer

950C or SaveProg software is required.

Programming the self-activation/self-start button to a speci-

fic pane

(different from the self-start function enabled using button “A”)

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED B

(ringtone mute) begins flashing.

3) Release buttons B and A.

4) Press and hold down the button to be programmed (D, E1, E2, E3, E4).

5) Wait until the monitor handset emits a tone.

6) Release the button.

7) Call the monitor from the panel you want to perform direct self-start

from:

- On push-button entrance panels, press the button corresponding to

the monitor on which the button is being saved.

- On alphanumeric panels, enter the ID corresponding to the monitor

on which the button is being saved and press the bell button on the

panel to confirm.

8) At the end of the procedure described above, the monitor handset emits

an audible signal to indicate that the procedure has been completed

correctly.

Default data restore procedure

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED B

(ringtone mute) begins flashing.

3) Release buttons B and A.

4) Press and hold down button A again.

5) While the monitor handset is emitting an audible signal, release button

A and press button C briefly.

The monitor programming has now been deleted. To check that program-

ming has been deleted, press button C; the monitor handset should emit

an audible signal.

Programming with SAVEPROG software

SaveProg is a PC software package supplied together with interfaces 692I

and 692I/U. These interfaces allow the PC to be connected to an entrance

panel or other suitable device, type 692I via an RS232 port and type 692I/U

via a USB connection.

After connecting the interface and installing SaveProg, on opening the pro-

gram the following window appears.

It is now possible to proceed with programming in two different ways:

1) with virtual 950C: clicking on icon opens an interactive image of

t950C programmer, which allows programming to be performed by si-

mulating use of the 950C programmer.

2) with the SaveProg windows: clicking on icon opens the “Device

configuration” window.

It is now possible to change button programming, create groups, select

ringtone types, adjust ringtone volume and enable or disable functions.

On completing the desired settings:

- save by clicking on .

- transfer the program to the device by clicking on the icon .

The device has now been reprogrammed.

Programming and configuring with programmer

type 950C

Interphone/monitor programming can be carried out using programmer

type 950C. The programmer must be connected to an entrance panel and

device configuration mode started. This programmer can be used to

change button programming, create groups, select ringtone types, adjust

the ringtone volume and enable or disable functions. For use of the pro-

grammer, please refer to the instructions.

Tab series interphone for Due Fili Elvox (Two-wire sy-

stems)

Art. 7509, 7509/D*

Fig. 2.1

Description

Interphone made of thermoplastic material with handset. Equipped with

four buttons for the main video door entry functions: door lock release,

self-start, auxiliary services (stair light), ringtone muting and 4 programma-

ble supplementary keys that can execute up to 4 auxiliary functions or in-

tercommunicating calls.

The following settings can be made: ringtone volume, ringtone muting

when “User Away” function is activated and ringtone type selection. Option

of setting different ringtones for calls made from different points, e.g.: out-

door entrance panel, door call, intercommunicating call.

LED signalling of “door/gate open” and “Unanswered calls” (up to 4 calls

with interphone in ringtone muted state).

For use in Elvox Two-Wire systems with power supply 6922.

Article 6901/D has a hearing aid function.

Before commencing programming, read the instructions carefully to

get a clear idea of the product’s characteristics, functions and featu-

res.

Technical characteristics

• Surface-mounted interphone made of ABS with mirror gloss finish on

front panel.

• Designed for external wall mounting or fitting to a box (can be mounted

directly on the wall using wall plugs or to a Vimar V71303 type unified 3-

module rectangular flush-mount back box or a 60 or 70 mm round flush-

mount back box).

• Touch-sensitive keys.

• Power supply from Two-Wire Bus

• Input current:

- on standby: 7mA

- maximum conversation current: 60mA

- peak current limited to call time: 100mA

• Operating temperature: 0° ÷ 40°C

• Electronic chime: different ringtones for panel call, intercom call and door

call.

• 10 different ringtones can be selected.

• Output for additional chime 860A or relay 0170/101.

• Input for door call.

• Interphone 7509 dimensions: 105x180x35 mm

A Self-start: for self-start/auto-activation of interphone (to

Master entrance panel by default).

B Ringtone muting: Mutes ringtone during call.

C Door lock: Lock opening command (programming can be

adjusted using the programmer).

D Auxiliary 1 (Stair light): For auxiliary service (actuator 1 of

relay 69RH or 69PH activated by default).

E1 Button 1: Programmable button to activate auxiliary ser-

vice or intercommunicating call (actuator 2 of relay 69RH or

69PH activated by default).

E2 Button 2: Programmable button to activate auxiliary ser-

vice or intercommunicating call.

E3 Button 3: Programmable button to activate auxiliary ser-

vice or intercommunicating call (entrance panel function F1

activated by default, the last entrance panel to make a call).

E4 Button 4: Programmable button to activate auxiliary ser-

vice or intercommunicating call (entrance panel function F2

activated by default, the last entrance panel to make a call).

Buttons

Fig. 2.2

F During normal operation:

- Flashing light: indicates that the interphone is receiving

a call (from outdoor entrance panel or from an intercom-

municating device).

- Steady light: ringtone muted.

- Steady light flashing every 10s: if calls have been

made from the entrance panel while the ringtone was

muted, the LED flashes a number of times equal to the

number of calls received from the entrance panel (up to

4 calls are memorised). The flash log is reset when the

ringtone volume is restored.

During programming:

- Flashing light: indicates programming mode.

G During normal operation:

- Steady light: indicates that the door is open if the sen-

sor has been installed on at least one entrance panel

and connected between terminals PA and M.

During adjustment:

- Flashing light: indicates that ringtone selection or vo-

lume adjustment is in progress.

Signals:

Connection terminal block:

1, 2 Two pairs of terminals for Two-Wire bus

E+, E- Additional power supply for monitor with power supply unit type

6923.

12V Connection of additional chime (positive reference 12V).

CH Connection of additional chime (call repetition).

FP Input for door call button (with reference to terminal M).

M Earth reference.

Connection terminal block

Operation

Important: For the interphone to work, the ID must have already been pro-

grammed. To check this, press any of the interphone buttons. If an ID has

been assigned to the interphone, a beep will sound when a button is pres-

sed; if no ID has been assigned or it has been deleted, a triple beep will

sound.

Operating times

The answer and conversation times depend on the configuration of the

corresponding entrance panel parameters (to change these times, please

refer to the electronic entrance panel unit instructions).

- Answer time (for entrance panel call): Default value 30 s

(minimum value 1 s, maximum value 255 s)

- Answer time (for intercommunicating call): 30 s (fixed value)

- Conversation time (for entrance panel call): Default value 120 s

(minimum value 10 s, maximum value 2550 s)

- Conversation time (for intercommunicating call): Default value 5 minu-

tes (can be modified to unlimited time).

Answering a call

A call from the outdoor entrance panel or from an intercommunicating de-

vice can be answered during the chime cycle or once it has ended. To an-

swer, lift the handset; to end the call, replace the handset.

Receiving a door call

The interphone can receive calls from a door call button if connected to

terminals M and FP directly or via interface 6120 (see wiring versions).

When the door call button is pressed, the interphone emits a different tone

to the one used for outdoor entrance panel calls or intercommunicating

calls. To stop the chime, lift the handset.

In the case of a door call by means of a button connected directly to the

interphone’s terminals FP and M; chime cycle duration depends on how

long the button was held down (max. 10 s).

Making an intercommunicating call

To make a call to another indoor unit, one or more buttons must have been

programmed (see “Button programming” section).

To make the call, press the button programmed for the relevant indoor unit.

During the call, the interphone emits a tone in order to signal that the call

is being made. If the interphone/monitor is already engaged in another call,

a tone will be heard on the interphone making the call to indicate that the

user receiving the call is busy.

When the indoor unit receiving the call answers, communication begins

automatically. Replace the handset to end the conversation.

The maximum conversation time is 5 minutes (default).

Muting the ringtone during a call (Mute function)

When receiving a call from an outdoor entrance panel or from an intercom-

municating device or a door call via device 6120, the call ringtone can be

muted by pressing button B.

Door lock command

Press the lock button (with the handset hooked on or in conversation) to

send a lock opening command to the entrance panel (by default, the last

entrance panel to make a call).

Self-start

- Self-start with dedicated button (button A):

to use the self-start function and communicate with the master entrance

panel, lift the handset and briefly press button A (self-start) and lift the

handset to start the conversation. Replace the handset to end the con-

versation.

- Self-start with programmed button to a specific panel:

to use the self-start function and communicate with a specific entrance

panel, lift the handset and press and release the button programmed to

call that entrance panel (see “Programming the self-activation/self-start

button to a specific panel ” section).

Calling a porter switchboard

To call a porter switchboard (if present in the system): lift the handset and

press button C (lock) to make the call.

Fig. 2.3

Fig. 2.4

Hearing aid function (art. 7509/D only)

Art. 7509/D has an internal coil which allows hearing aid wearers to use the

device. In this operating mode, the hearing aid must be switched to the “T”

position. However, for correct operation of the hearing aid refer to its in-

struction manual.

Note: metal objects or electronic equipment in the vicinity may affect the

quality of the sound received by the hearing aid.

Configurations

Choice of ringtones

10 different ringtones can be selected. Different ringtones can also be set

for outdoor, intercommunicating and door calls (see below). The ringtones

must be selected with the interphone/monitor on stand-by and the handset

on the hook.

The button for entering configuration mode is button A (self-start).

Button E1 selects the ringtone for ENTRANCE PANEL CALL.

Button E2 selects the ringtone for INTERCOMMUNICATING CALL.

Button E3 selects the ringtone for DOOR CALL (exclusively using the but-

ton interface module 6120 or Vimar landing call button). In the case of a

door call by means of a button connected directly to the interphone’s ter-

minals FP and M, the ringtone cannot be changed.

Configuration:

1) Press button A (self-start) and hold down (for 2 s) until the LED G

“door/gate open” begins flashing and the interphone emits an audible

signal.

2) Press and hold down the button for the chosen ringtone (button

E1/button E2/button E3) until the ringtone is heard on the interphone.

3) Press the button repeatedly (button E1/button E2/button E3) to select

the desired type of ringtone.

4) After choosing the desired ringtone, press button A or refrain from tou-

ching any buttons for 5s to save. After completing the configuration, the

LED flashes and then turns off.

Ringtone volume adjustment

The ringtone volume can be set to 6 levels plus mute.

Press button A (self-start) to enter configuration mode.

Press button B (bell) to lower the ringtone volume.

Press button C (key) to increase the ringtone volume.

The ringtone volume must be adjusted with the interphone/monitor on

stand-by and the handset on the hook.

Configuration:

1) Press button A (self-start) and hold down (for 2 s) until the LED G

“door/gate open” begins flashing and the interphone emits an audible si-

gnal.

3) Press button B to lower or button C to increase the volume. Each time

the buttons are pressed the volume changes by one level.

4) After choosing the desired volume, press button A or refrain from tou-

ching any buttons for 5s to save. After completing the configuration, the

flashing LED goes off and a “beep” is emitted.

Muting the ringtone (User Away function)

Using the volume adjustment procedure described above, pressing button

B a sufficient number of times results in the ringtone being muted. The “Rin-

gtone muted” status is indicated by the LED F (ringtone muted) lighting up

steadily.

If the interphone receives a call from the entrance panel while the ringtone

is muted, this is indicated by the LED F (ringtone muted) emitting one flash

for each unanswered call up to a maximum of 4 calls (these flashes occur

every 10 s). When the ringtone volume is restored, at least to its minimum

level, this indication will be reset.

Bus termination for video signal stabilisation

The BUS termination dip-switches for video signal stabilization are located

inside the interphone.

Depending on the connection configuration (interphones/monitors connec-

ted in series or derived from a distributor), set the dip-switches in the ap-

propriate position (position A, B or C) according to the instructions given

in the note “Bus termination for ELVOX TWO-WIRE INSTALLATIONS” in

the wiring diagrams section below.

Dip-switch for

Bus termination

OPEN

100Ω

50Ω

Manual programming

Basic interphone/monitor programming is as follows:

- Programming ID, which must be performed on the interphone that recei-

ves the call individually or on the first interphone of a group of interpho-

nes/monitors with simultaneous calls (master interphone).

- Programming secondary ID, which must be done for interphones asso-

ciated with a master interphone/monitor.

- Programming programmable buttons or changing the default setting of

supplementary buttons, for auxiliary services or intercommunicating calls.

Programming must be carried out with the system switched on, without ac-

tive communication and only after the interphones/monitors have been con-

nected to the system and the entrance panels have been programmed.

N.B.: all the programming or deletion phases must be performed with

the interphone/monitor handset lifted and held against the user’s ear.

Programming ID identification code

The identification code is programmed by means of a main entrance panel

(MASTER), already configured and present in the system.

The interphone is supplied without associated identification code. To verify

this, press the lock release button and the interphone should emit an audi-

ble signal (triple beep).

To program the ID, proceed as follows:

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED F

(ringtone mute) begins flashing.

3) Release the buttons.

4) Press button C and hold it down (for 2 sec.) until the handset emits an

audible signal and communication between the interphone and the out-

door entrance panel begins.

5) Release button C.

Important: you will have 5 s in which to press button C (as indicated in step

4). If button C is not pressed within the 5 s, steps 1, 2 and 3 must be repea-

ted.

6) You now have approx 30 seconds to assign the ID code of the external

entrance panel:

- in the case of an alphanumeric panel, key in the primary ID and press

the “bell” button to confirm.

- in the case of a push-button entrance panel, press the button you

want to use to call the interphone.

Important: If the system already contains an interphone with the same as-

sociated identification code, the entrance panel emits a low tone and the

process must be repeated from the start in order to assign a different code.

Programming secondary ID

Programming the secondary ID is only necessary when you want more than

one interphone/monitor to ring in response to the same pushbutton or call

code. The interphones/monitors that are to ring at the same time are asso-

ciated with the same group. The “master” interphone/monitor is program-

med first by means of the “identification code programming” procedure

described above, while the additional group interphones/monitors are pro-

grammed with the secondary identification code.

The maximum number of interphones/monitors that can be associated with

the same group without using a 950C programmer is 3 plus a master unit.

Alternatively, a 950C programmer or SaveProg software can be used to pro-

gram activation of the ringtone of all video door entry units and the monitor

of only the master unit. Before answering from a secondary audio/video

door entry unit, the relevant monitor can be turned on by means of the self-

start button.

To program the secondary ID, proceed as follows:

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED F

(ringtone mute) begins flashing.

3) Release the buttons.

4) Press buttons A and C simultaneously and hold them down (for 2 sec.)

until the handset emits an audible signal and communication between

the interphone and the outdoor entrance panel begins.

5) Release buttons A and C.

Important: you will have 5 s in which to press buttons A and C (as indica-

ted in step 4). If buttons A and C are not pressed within the 5 s, steps 1, 2

and 3 must be repeated.

6) You now have approx 30 seconds to assign the ID code of the exter-

nal entrance panel:

- in the case of an alphanumeric panel, key in the primary ID and

press the “bell” button to confirm.

- in the case of a push-button entrance panel, press the button you

want to use to call the interphone.

Important: When programming the primary and secondary ID, the inter-

phones undergoing programming automatically acquire a code that de-

pends on the association with the button or code used to call the outdoor

entrance panel. Correspondence between the primary ID and the respec-

tive secondary ID codes is provided in the table below.

Example: If ID = 8 is given to a second interphone, the automatic second

interphone identification attribution procedure will automatically assume ID

= 72 (see table).

When a call is made to ID = 8, both interphones will chime and both can be

used to answer. If, on the other hand, in the case of an alphanumeric panel

you enter 72 (the ID automatically assigned by the procedure), a chime is

emitted by the interphone for which the secondary ID assignation proce-

dure was carried out and only this interphone can be used to answer the

call.

Table of primary and corresponding secondary ID codes:

Important: to delete from a group, the programming deletion procedure de-

scribed in the “Default data restore procedure” section must be performed.

Button programming

Important: without programmer 950C or SaveProg software, the only fun-

ctions that can be assigned are intercommunication, specific entrance

panel self-activation, restoring buttons programmed by the installer to their

default settings and restoring default data.

Button programming procedure for intercommunicating calls

To program the buttons, proceed as follows:

1) Press the “talk/listen” button or lift the handset (depending on model in-

stalled) for the interphone/monitor TO BE CALLED.

2) Lift the handset to be programmed (the caller handset).

3) Press buttons B and A on the interphone to be programmed (caller) si-

multaneously and hold them down until LED F (ringtone mute) begins

flashing.

4) Release buttons B and A.

5) Press and hold down the button to be programmed (e.g. E1, E2, E3, E4).

6) Wait until the interphone handset emits a continuous tone.

7) Release the button to be programmed on the caller interphone.

8) Press a button (lock/F1/F2) on the interphone/monitor to be called.

9) An audible signal in the handset of the (caller) interphone being program-

med confirms that the procedure has been completed correctly.

Primary ID

Secondary ID

1 2 3

26 126 127 128

27 129 130 131

28 132 133 134

29 135 136 137

30 138 139 140

31 141 142 143

32 144 145 146

33 147 148 149

34 150 151 152

35 153 154 155

36 156 157 158

37 159 160 161

38 162 163 164

39 165 166 167

40 168 169 170

41 171 172 173

42 174 175 176

43 177 178 179

44 180 181 182

45 183 184 185

46 186 187 188

47 189 190 191

48 192 193 194

49 195 196 197

50 198 199 200

Primary ID

Secondary ID

1 2 3

1 51 52 53

2 54 55 56

3 57 58 59

4 60 61 62

5 63 64 65

6 66 67 68

7 69 70 71

8 72 73 74

9 75 76 77

10 78 79 80

11 81 82 83

12 84 85 86

13 87 88 89

14 90 91 92

15 93 94 95

16 96 97 98

17 99 100 101

18 102 103 104

19 105 106 107

20 108 109 110

21 111 112 113

22 114 115 116

23 117 118 119

24 120 121 122

25 123 124 125

Procedure for restoring default data for each individual button

(E1, E2, E3, E4)

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED F

(ringtone mute) begins flashing.

3) Release buttons B and A.

4) Press and hold down the button you want to return to default program-

ming (not valid for Self-start and Lock buttons).

5) Wait until the interphone handset emits an audible signal.

6) Release the button.

7) Press the button again to confirm. The interphone handset will again

emit a signal. The button has now been restored to its default value.

Important: This procedure can be used to manually reprogram all buttons

with the exception of the lock and self-start buttons, for which programmer

950C or SaveProg software is required.

Programming the self-activation/self-start button to a specific

panel

(different from the self-start function enabled using button “A”)

1) Lift the handset.

2) Press buttons B and A simultaneously and hold them down until LED F

(ringtone mute) begins flashing.

3) Release buttons B and A.

4) Press and hold down the button to be programmed (D, E1, E2, E3, E4).

5) Wait until the interphone handset emits an audible signal.

6) Release the button.

7) Call the interphone from the panel you want to perform direct self-start

from:

- On push-button entrance panels, press the button corresponding to

the interphone on which the button is being saved.

- On alphanumeric panels, enter the ID corresponding to the inter-

phone on which the button is being saved and press the bell button

on the panel to confirm.

8) At the end of the procedure described above, the interphone handset

emits an audible signal to indicate that the procedure has been com-

pleted correctly.

Default data restore procedure

1) Lift the handset.

2) Press buttons B and A on the interphone to be programmed (caller)

simultaneously and hold them down until LED F (ringtone mute) begins

flashing.

3) Release buttons B and A.

4) Press and hold down button A again.

5) While the interphone handset is emitting an audible signal, release but-

ton A and press button C briefly.

The interphone programming has now been deleted. To check that pro-

gramming has been deleted, press button C; the interphone handset should

emit an audible signal.

Programming with SAVEPROG software

SaveProg is a PC software package supplied together with interfaces type

692I and type 692I/U. These interfaces allow the PC to be connected to an

entrance panel or other suitable device, type 692I via an RS232 port and

type 692I/U via a USB connection.

After connecting the interface and installing SaveProg, on opening the pro-

gram the following window appears.

It is now possible to proceed with programming in two different ways:

1) with virtual 950C: clicking on icon opens an interactive image of

the 950C programmer, which allows programming to be performed by

simulating use of the 950C programmer.

2) with the SaveProg windows: clicking on icon opens the “Device

configuration” window.

It is now possible to change button programming, create groups, select

ringtone types, adjust ringtone volume and enable or disable functions.

On completing the desired settings:

- save by clicking on .

- transfer the program to the device by clicking on the icon .

The device has now been reprogrammed.

Programming and configuring with programmer

type 950C

Interphone/monitor programming can be carried out using programmer

type 950C. The programmer must be connected to an entrance panel and

device configuration mode started. This programmer can be used to

change button programming, create groups, select ringtone types, adjust

the ringtone volume and enable or disable functions. For use of the pro-

grammer, please refer to the instructions.

Fig. 3.5

226 mm

65 mm

89 mm

Interphone series Petrarca

type 6209

Description

Type 6209 is an interphone in the Petrarca series for ELVOX 2-WIRE audio

and video door entry systems. It is supplied as standard with 3 pushbut-

tons, one for lock release, one for self-start of the interphone in the system

even when not called, and one for the auxiliary “stair light” service. The in-

terphone can be fitted with an additional 3 pairs of pushbutton types 692P

(692P/M or 692P/R), for auxiliary services or intercommunicating calls, and

the accessory type 6153/682 for: call volume adjustment, call signal mute,

call denied luminous indicators, signal to indicate unanswered calls, signal

to indicate services not available and luminous signal for gate/door open.

The interphone can be installed as a wall-mounted version or desktop

using the conversion kit type 6140 or 6A40, or in combination with moni-

tors in the Petrarca series type 6029 (b/w monitor) or type 6029/C (colour

monitor) by means of wall bracket type 6145 or desktop conversion kit

type 6142 or 6A42.

Connection and connector terminal board

1, 2) BUS line.

4, 6P) Connection for door call pushbutton.

5, 6S) Connection of additional door ringtone

-, +)

Additional power supply for monitor with power supply type 6923.

VARIAT.) Connection for module type 6153/682.

VIDEO) Connection for monitor type 6029 or 6029/C.

T1) 1st pair of pushbuttons type 692P.

T2) 2nd pair of pushbuttons type 692P.

T3) 3rd pair of pushbuttons type 692P.

T4) 4th pair of pushbuttons type 692P.

Controls

The call volume can be adjusted by moving the loudspeaker wire from

connector A+ (high) to A- (low); otherwise use accessory type 6153/682,

leaving the loudspeaker wire connected to connector A-.

Fig. 3.4

BL BIRO A+ CAA- VARI AT.

SERR.

SERIALE

PRG.

VIDEO

Per art. 6153/682

RESET

SERRATURA

Per art. 6009 o

6009/C

Stabilizzazione

segnale video

TR1

TR2

Video signal

stabiliser

TR1, TR2) Do not touch, trimmers already set by the firm.

For

Lock

For Art. 6029 o

Art. 6029/C

INSTALLATION

Wall-mounted installations of the interphone do not require additional ac-

cessories.

However a vertical 3-module box may be used to facilitate fixture and cable

routing. For desktop installations and combinations with monitors, refer to

the respective instructions of the conversion kit or monitor.

Fig. 3.7

Fig. 3.6

VIDEO SIGNAL STABILISATION

Inside the interphone there are some connec-

tors (A-B-C) and some jumpers for the video si-

gnal stabilization.

This jumper must be used in video installations

with several appliances (interphones and moni-

tors) connected in series (Fig. 3.6).

In series configuration displace the jumper

(only in the last set) into “B” position and keep

the jumpers of other interphones/monitors in

the initial position, i.e. “A”. (Fig. 3.6).

For other wiring configurations see note: "Bus

termination for ELVOX TWO-WIRE installations"

provided (Page. 44).

PROGRAMMING

There are three interphone programming modes: assignment of an iden-

tification code or call code (indispensable), assignment of a secondary

identification code (for interphones associated with a master interphone),

programming of pushbuttons for auxiliary services and intercommunica-

ting calls (when necessary).

Programming must be performed with the system switched on, without

active communication and only after connecting the interphones/monitors

to the system and programming the panels.

Identification code programming

The identification code is programmed via an entrance panel (MASTER),

already configured and present on the system.

The interphone is supplied without associated identification code. To ve-

rify this condition, press the lock release pushbutton and the interphone

should emit a triple “Beep”.

Attention: during the interphone/video interphone identification code

programming you have 30 seconds from the moment you enter the

programming in the interphone/video interphone and the moment

you press the call push-button on the panel or you send the code.

Programming phase:

1) Remove the interphone cover.

2) Press and hold the RESET pushbutton on the interphone.

3) Press and hold the tab on the lock release pushbutton, together with

the RESET pushbutton.

4) Release the RESET pushbutton, keeping the lock release pushbutton

pressed.

5) After 2 seconds the interphone emits a high tone and communication

is enabled with the panel. If the monitor is also connected to the inter-

phone, it is switched on and connected to the camera of the entrance

panel.

6) Release the tab of the lock release pushbutton.

7) On pushbutton entrance panels, press the call button for the inter-

phone, while on alphanumeric keypads, enter the call code and press

pushbutton “ ”.

8) If the system contains an interphone that already has the same asso-

ciated identification code, the panel emits a low signal and the opera-

tion should be repeated from point 2.

9) Otherwise the code is associated with the interphone and communi-

cation is terminated.

Intercommunicating call pushbutton programming

Programming phase:

1) Raise

the handset of the interphone/video interphone to call

(when using series 8870, Giotto, Petrarca). With other versions of

series 6600 (without handset) press and keep pressed the

talk/listen push-button .

2) Remove the cover of the interphone to be programmed.

3) Press and hold the RESET push-button on the audio door entry unit to

program.

4) Press and hold the additional pushbutton to make the intercommuni-

cating call together with the RESET pushbutton.

5) Release the RESET pushbutton, keeping the call pushbutton pressed.

6) After 2 seconds the interphone emits a high tone, while the other in-

terphone emits a 3-tone ascending scale.

7) Release the intercommunicating call pushbutton.

8) On the interphone called (with the 3-tone ring), press one of the pro-

grammed pushbuttons (such as lock, F1, F2 or actuator).

9) A high tone confirms the end of the procedure.

Repeat the same procedure for the other interphones and any other inter-

communicating call pushbuttons.

Programming the self-start pushbutton to a specific panel.

Programming phase:

1) Remove the interphone cover.

2) Press and hold the RESET pushbutton on the interphone.

3) Press and hold the additional pushbutton to activate the self-start fun-

ction together with the RESET pushbutton.

4) Release the RESET pushbutton, keeping the self-start pushbutton

pressed.

5) After 2 seconds the interphone emits a high tone.

6) Release the self-start pushbutton.

7) On pushbutton entrance panels, press the call button for the inter-

phone, while on alphanumeric keypads, enter the call code and press

pushbutton “ ”.

8) A high tone confirms the end of the procedure.

Restoring default values of pushbuttons

(P2,P3,P4,P5,P6,P7,P8)

Programming phase:

1) Remove the interphone cover.

2) Press and hold the RESET pushbutton on the interphone.

3) Press and hold the relative pushbutton to be reprogrammed together

with the RESET pushbutton.

4) Release the RESET pushbutton, keeping the other pushbutton pressed.

5) After 2 seconds the interphone emits a high tone.

6) Release the pushbutton to restore to default and then press again.

Deleting all settings.

Programming phase:

This procedure is advised when you want to change the ID of an inter-

phone/monitor previously programmed and you do not want keep the ope-

ration programming of the appliance.

1) Remove the interphone cover.

2) Press and hold the RESET pushbutton on the interphone.

3) Press and hold the self start pushbutton together with the RESET pu-

shbutton.

4) Release the RESET pushbutton, keeping the self-start pushbutton

pressed.

5) After 2 seconds the interphone emits a continuous tone for two se-

conds.

6) Release the self-start pushbutton.

7) During the continuous tone, press the tab on the lock release pushbut-

ton.

If the deletion procedure is successful, when the lock release tab is

pressed once more the interphone emits a triple “Beep”.

Secondary identification code programming

Programming of the secondary identification code is only required when

more than one interphone is to be called by means of the same pushbut-

ton or call code. The interphones that ring at the same time are associa-

ted with the same group. The “master” interphone is programmed first by

means of the “identification code programming” procedure described

above, while the additional group interphones are programmed with the

secondary identification code (see table page 44).

A maximum of three audio door entry units plus one group master can

be associated with the same group, without the need for programmer

Type 950C or SaveProg .

If the interphones are combined with Petrarca monitors, an additional

power supply type 6923 must be fitted for each additional monitor

after the second monitor. Using programmer type 950C, activation of

the ringtone on all monitors can be programmed, without simultane-

ous activation of all monitors, to then enable activation of the moni-

tor from the interphone used to answer the call with the self-start

pushbutton; this avoids the need to use additional power supplies.

Programming phase:

1) Remove the interphone cover.

2) Press and hold the RESET pushbutton on the interphone.

3) Press and hold the tab on the lock release pushbutton and the self

start/auto-activation pushbutton (the first pushbutton below the tab),

together with the RESET pushbutton.

4) Release the RESET pushbutton, keeping the other two pushbuttons

pressed.

5) After 2 seconds the interphone emits a high tone and communication

is enabled with the panel. If the monitor is also connected to the inter-

phone, it is switched on and connected to the camera of the entrance

panel.

6) Release the tab on the lock release pushbutton and the self start pu-

shbutton.

7) On pushbutton entrance panels, press the call button for the “master”

interphone, while on alphanumeric keypads, enter the call code of the

“master” interphone and press pushbutton “ ”.

8) When the secondary code is associated with the interphone and com-

munication is terminated.

To know the number assigned see table shown in the wiring diagram section.

Pushbutton programming

The interphone is supplied with a pair of additional pushbuttons type 692P,

for the functions self start and the auxiliary service “stair light”, which ac-

tivates the 1st relay of the 1st actuator (type 692R), if connected to the sy-

stem. A further three pairs of pushbuttons type 692P can be inserted in

the interphone, to be connected to connectors T2-T3-T4, corresponding to

the following default functions.

Pushbutton Connector In program. Default function

1° T1 P1 Self-start

2° T1 P2 Stair light (1st relay of 1st

actuator, type 692R)

3° T2 P3 Auxiliary (2nd relay of 1st

actuator, type 692R)

4° T2 P4 Not associated

5° T3 P5 Not associated

6° T3 P6 Not associated

7° T4 P7 Function F1 on panel

8° T4 P8 Function F2 on panel

P0 is the lock button.

To change the operating mode of buttons P0 and P1, use programmer type

950C or the Save Prog software.

OPERATION

Calls from an entrance panel, intercommunicating calls and door calls are

differentiated by means of different tones.

Door calls.

Calls from entrance panels do not follow the pressed pushbutton but are

generated inside the interphone. The call interval is 1 s of ringtone and 2 s

of pause repeated twice (default value set on panel). To answer, raise the

handset. If the handset is already raised during the call, replace and raise

it again. The call answer time (30 s) and the conversation time (2 minutes

by default) are set in the panel parameters. When the conversation time

has elapsed, the user can continue without replacing the handset if a new

call is made within 10 s from the same panel.

Intercommunicating call.

Lift the handset and press the intercommunicating button for the inter-

phone/monitor to be called. On the handset of the interphone called a call

tone will ring (if the call is enabled) or an engaged tone (if not enabled). On

the called interphone the ringtone starts sequentially at intervals of 1 s rin-

ging and 4 s pause. The maximum duration of the call is 30 s (6 cycles). To

answer the call, simply raise the handset; the maximum duration of the

conversation is 60 seconds. When the conversation time has elapsed, the

user can continue without replacing the handset if a new call is made wi-

thin 10 s. Calls from the panel have priority over intercommunicating calls.

Denied calls.

Installation of type 6153/682 in the interphone, enables the user to vary

the call intensity or mute the ringtone. Call mute is indicated by perma-

nent illumination of the red LED. If calls are made to the interphone when

the call mute is enabled, they are denied. A denied call causes the red Led

to briefly switch off according to the number of times calls are denied (ma-

ximum 4 denied calls). The signal is repeated every 10 s (approx.). Deletion

of denied calls is by: reenabling the ringtone, resetting the interphone or a

system power failure. On the panel, a denied call is indicated by means of

a dissuasion tone (a series of “Beeps” at 100ms intervals with a pause of

100ms for a total of 5 s).

The message “Do not disturb” also appears on panels with display.

Lock Button

The lock button of each device works in the following manner.

- Device with handset at rest lock to the last entrance panel with

which it has spoken or from which it has been called.

- Device with handset raised but not engaged in a conversation

call to switchboard if the Switchboard flag is YES. Otherwise it goes

back to the first case.

- Device with handset raised and engaged in an internal conversation

as in the first case.

- Device with handset raised and engaged in an external conversation or

called from entrance panel lock to the entrance panel being spo-

ken with or from which it has been called.

In practice a lock is always activated except when the handset is raised

and you immediately press the lock button. This can also be taken to the

standard case if the system has no porter switchboard and the Switchbo-

ard flag is set on NO.

Type 6029 - 6029/C

PETRARCA SERIES MONITOR FOR TWO ELVOX WIRES

DESCRIPTION

PETRARCA series monitor type

6029

or 6029/C

can work in conjunction

with interphone type

6209 or 62I8

for video door entry systems series

TWO WIRES ELVOX or TWO WIRES VIDEOKIT.

TECHNICAL CHARACTERISTICS OF type 6029

- Slim-line surface wall-mounted monitor with 3.5” B/W

- Video signal standard: CCIR with 625 lines and 50 frames (EIA stan-

dard available on request)

- Passband: 4 MHz

TECHNICAL CHARACTERISTICS OF type 6029/C

- Slim-line surface wall-mounted monitor with LCD colour screen 3.5”

- Video signal standard: PAL

Contrast (colour) Brightness

MONITOR DIMENSIONS AND ADJUSTMENTS

226 mm

48 mm135 mm

Fig. 3.8

Monitor series Giotto

type 6329, 6329/C

Description

Type 6329 and 6329/C are interphones in the Giotto series respectively

with B/W (6329) and colour screen (6329/C) for ELVOX 2-WIRE video door

entry systems. They are supplied as standard with 3 pushbuttons, one for

lock release, one for self-start of the monitor in the system even when not

called, and one for the auxiliary “stair light” service. Supplied with call vo-

lume adjustment on 3 levels and call mute. The luminous indicators of: call

signal mute, unanswered calls, services not available and gate/door open,

are signalled by means of two LEDs (red and green) present on the moni-

tor.

The monitor can be installed as a wall-mounted version, by means of the

bracket (R684) supplied with the monitor, or desktop version by means of

the conversion kit type 661A or 661F.

220 mm

71 mm204 mm

Fig. 4.1

Monitor technical specifications

- Wall-mounted monitor in ABS

- Backing plate and plugs for wall-mounted fixture or 3-module box.

- 3.5" flat screen for 6329 and 3.5" flat screen for 6329/C.

- Electronic circuit on interchangeable cards.

- Standard video signal CCIR 625 lines 50 squares for 6329 and PAL for

6329/C.

- Video pass band 4 MHz

- Operating temperature from 0° to +40° C.

- Electronic ringtone.

- Input for door calls with different ringtone from panel calls.

- Output for additional ringtone type 860A.

- Supply of data from bus.

- Input for additional power supply (type 6923) if the system is configured

to enable simultaneous activation of more than two monitors.

Connection and connector terminal board

3, 4) Additional ringtone connection

1, 2) BUS line.

12 +, 13 -) Additional power supply for monitor with power supply type 6923.

V3, M) Connection for door call pushbutton.

CN1) Connection for monitor.

Fig. 4.2

ELVOX

CS2350

271103

4 3 2 1

A S

BUS

12 13 V3 M

EXT. 24V

F.P.

+ -

CN2

CN1

Stabilizzazione

segnale video

Per monitor

Video signal

stabilization

For monitor

Fig. 4.5

Fig. 4.3

Fig. 4.4

P1 + P2 (Toghether) =

Fig. 4.6

Controls and adjustments (Fig. 4.4 - 4.5)

A - Ringtone volume and mute control.

B - Brightness control.

C - Contrast control for 6329 and color for 6329/C

D - Lock release pushbutton .

E - System self-start pushbutton .

F - Pushbutton for auxiliary service, 1st relay of 1st actuator type

69RH.

When the pushbuttons and are pressed together, a second

auxiliary service is activated, 2nd relay of 1st actuator type 69RH.

G - RESET pushbutton for monitor programming.

H - Ringtone mute LED. The fixed light illuminates when the ringtone mute

is enabled by means of slider "A" and flashes when calls have been

denied (red led).

I - Door open LED. On systems in which this function is used, the LED re-

mains lit permanently when the door/gate is open (green led).

VIDEO SIGNAL STABILISATOR

On the monitor intercommunication card

there is a connector (A-B-C) and a jumper for

the video signal balance (Fig. 4.5).

This jumper must be used on the installations

where there are more appliances (interpho-

nes or monitors) connected in series (Fig.

4.5).

Displace the jumper into "B" (Termination 100

Ohm) only on the last set and keep the jum-

pers on the other appliances in the initial po-

sition "A" (No termination).

For other wiring configurations see note:

"Bus termination for ELVOX TWO-WIRE in-

stallations" provided (Page. 44).

Page is loading ...

Elvox 6621 Operating instructions

Brand: Elvox

Model: 6621

Category: Telephones

Type: Operating instructions

Download PDF

report

Elvox 6621 Operating instructions

Elvox 6621 Operating instructions

Related papers

Other documents