To assure that assembly is carried out properly, make sure to read these instructions before you begin the assembly.
Parts Check
A
B
C
1
2
3
4
5
6
Plain washers: 8
Spring washers: 8
Hex bolts: 8
Screws (4 x 20 mm): 4
Screws (4 x 16 mm): 2
Headphone hook: 1
A
B
C
Legs: 3
Lyre assembly: 1
Lyre support sticks: 2
D
Caster cups: 3
A
A
C
D
7
Cord clamps: 3
* The tools used for assembly are not included. You will need to separately provide a Philips screwdriver (no. 2)
and a box wrench (19 mm across ats, length 200 mm or less).
Do not use an electric screwdriver. Doing so might strip the bolt or damage the screw threads.
Assembly Procedure
5 This leaet is for a dealer or a qualied professional installer. The customer should not attempt to move or
assemble the instrument.
5 Please consult your Roland dealer or a piano specialist to move or disassembling / assemble the piano.
Roland cannot warrant the safety of the assemble operation, if this operation is carried out by the
customer.
5 Save this leaet together with the Owner’s Manual so that it will be available for reference by a piano specialist when disassembling or
moving the instrument.
Attach the Lyre Assembly
1. Place a spring washer
2
and a plain washer
1
in that
order onto each hex bolt
3
. Use the box wrench to
fasten the lyre assembly
B
to the piano with the bolts
(two locations).
* Do not tighten hex bolts
3
excessively. Stop tightening when the
spring washer
2
becomes at.
2. Use screws
4
to fasten the pedal support sticks
C
(four locations).
Take care that the
support rod is in
the correct vertical
orientation.
Placing the Casters on the Caster Cups
NOTE
Be sure to place the casters on the caster cups. If the casters are
not secured by the caster cups, the piano will move when force
is applied to it, causing a hazardous situation.
1. Place the casters on the caster cups
D
(three locations).
* Be careful not to pinch your hands or drop this unit on your foot.
2. Position the casters and the metal parts that support
the casters in the directions shown in the illustration
below.
Direction of casters
Direction of the
metal parts that
support the
casters
Attach the Other Parts
1. Use two screws
5
to fasten the headphone hook
6
.
2. Connect the pedal cord to the Pedal connector.
3. As shown in the illustration, use the cable fasteners to
secure the pedal cord (three locations).
Cable fastener
4. Insert the included power cord into the AC adaptor,
and use a cable fastener to secure it (one location).
5. Insert the power cord plug into an AC outlet.
6. As necessary, ax cord clamps
7
to fasten the pedal
cord.
This completes assembly.
First hand-tighten each
bolt ve or six turns,
and then use the
box wrench to
tighten it rmly.
1
2
3
B
To AC outlet
AC adaptor
Cable fastener
Power cord
Leaet For a Dealer or a Qualied Professional Installer
Attach the Legs to the Piano
NOTE
The surface of the piano unit and the stand are very delicate;
handle with care to avoid scratching them.
1. Position the legs
A
in place beneath the piano.
2. Place a spring washer
2
and a plain washer
1
in that
order onto each hex bolt. After provisionally hand-
tightening the bolts, use the box wrench to secure the
legs
A
to the main piano unit (two locations).
* Do not tighten hex bolts
3
excessively. Stop tightening when the
spring washer
2
becomes at.
A
First hand-tighten
each bolt ve or six
turns, and then use
the box wrench to
tighten it rmly.
1
2
3
3. Fasten the two other legs
A
to the piano in the same
fashion.
Copyright© 2017 ROLAND CORPORATION
1
* Since this product is very heavy, you must make sure that a sucient number of people are on hand to help, so you can lift and move it safely,
without causing strain. When assembling the unit, obtain the assistance of enough people that assembly can be performed safely and as
directed.
* Do not place the main piano unit itself directly on the oor. Doing so will damage the jack enclosure, AC adaptor, and headphone hook that are
located on the bottom of the main piano unit.
* Be careful not to pinch your hands or drop this unit on your foot during assembly or transport.
Box wrench
200 mm or less
19 mm across ats
* 5 1 0 0 0 5 9 2 1 4 - 0 1 *
1
ROOMS TO GO 22158958 Assembly Instructions
Artesia DP-3+ Assembly Manual
Artesia Dp-10e Assembly Manual
Artesia AG-40 Assembly Manual
Artesia AP-100 Assembly Manual
Suzuki G-33 Easy Assembly Manual
Kawai EP308 Owner's manual
Yamaha YV3030MS Owner's manual
