Bulletin PC-BAP-K
The Model BAP-K Bin Aerator Pad Mounting Kit completely
eliminates the need to enter the bin to install or service aerators.
By cutting a 2-5/8” x 6-3/8” hole in the bin wall, the mounting kit
can be completely installed and serviced from outside of the bin.
After the initial hole has been cut, the bin aerator pad can be
mounted on the adapter assembly and inserted into the bin in less
than two minutes. There are no other holes to drill, tapping or
welding. The bin aerator pad is positively sealed and securely held
in place in the bin. Removal is just as simple and quick.
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com
Specifications - Installation and Operating Instructions
Model BAP-K Bin Aerator Pad Mounting Kit
7-1/2
[190.50]
3-3/4
[95.25]
11/16
[17.46]
5/32
[3.81]
1/8 FEMALE NPT
FOR TANK NIPPLE
1/16˝ GASKET
MOUNTING BRACKET
3/16˝ GASKET
SPRING
STEEL
CLAMP
Ø1/2˝ OPENING
IN CENTER
OF CLAMP
2X WASHERS
RUBBER
GASKET
1/8 NPT X 2˝
TANK NIPPLE
3/4˝ NUT
MOUNTING HARDWARE
OPTIONAL BAP-K MOUNTING KIT
BAP AERATOR
PC-BAP-K:TEMPLATE 12/12/08 9:48 AM Page 1
Installation Instructions:
1.
2.
3.
4.
5.
6.
7.
Cut a 2-5/8˝ x 6-3/8˝ hole in the bin wall (See Bulletin PC-BAP
for number of aerators and spacing).
Peel off the protective tape on one side of thin gasket (Figure 1,
Part A) and attach to the front side of the adapter (Part B). Refer
to Figure 1.
Peel off the protective tape on other side of gasket (Figure 1,
Part A) and place aerator on gasket. Upturned edges on
adapter will prevent aerator from turning in the bin.
Peel off the protective tape on the thick gasket (Figure 1, Part
C) and attach to back side of adapter. Longer legs on this side
of adapter keep adapter from turning when placed in bin wall
hole.
Insert tank nipple into aerator and tighten. The end with fewer
threads goes into the aerator. If the tank nipple is not secure in
aerator, it may unthread when aerator is removed from bin.
Slip clamp (Figure 1, Part D) over tank nipple with legs toward
aerator and thread on brass locking nut.
Holding the aerator by the tank nipple, slip the entire assembly
through bin wall. Rotate the clamp to bridge the opening and
tighten locknut. Aerator is securely held in place and hole in bin
wall is positively sealed (refer to Figure 3).
©Copyright 2008 Dwyer Instruments, Inc. Printed in U.S.A. 12/08 FR# R5-443675-00
MAINTENANCE
Upon final installation of the Series BAP-K Bin Aerator Pad
Mounting Kit, no routine maintenance is required. A periodic check
of system calibration is recommended. The Series BAP-K is not
field serviceable and should be returned if repair is needed (field
repair should not be attempted and may void warranty). Be sure to
include a brief description of the problem plus any relevant
application notes. Contact customer service to receive a return
goods authorization number before shipping.
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com
A.
B. C.
D.
Figure 1: Kit Parts
A. 1/16˝ gasket with adhesive both sides
B. Adapter (front view)
C. 3/16˝ gasket, adhesive one side
D. Spring steel clamp
Figure 2: BAP-K Assembly with BAP Bin Aerator Pad
AERATOR WITH
TANK NIPPLE
KIT: THIN
GASKET
KIT: ADAPTER
KIT: THICK
GASKET
KIT: SPRING
STEEL CLAMP
BRASS NUT
Figure 3: Aerator Kit Installed in Bin Wall
PC-BAP-K:TEMPLATE 12/12/08 9:48 AM Page 2
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Dwyer Series BAP User manual
-
-
-
-
-
-
-
-
-