Dwyer Series TG User manual

Brand: Dwyer

Model: Series TG

Type: User manual

Series TG Polycarbonate Wall Mount Thermostat Covers

Specifications - Installation and Operating Instructions

Bulletin H-2-TG

The Series TG Polycarbonate Thermostat Cover

prevents physical damage and unauthorized adjustments of

thermostats. Two sizes of covers are available to fit most

common thermostats and transmitters. The low profile

design with ventilation slits allows exceptional air flow in

order to obtain accurate measurements.

TOOLS LIST

Included:

1 Series TG Thermostat Cover

2 Keys

4 Concrete Screws

4 Drywall Screws

4 Plastic Anchors

Tools Required:

Pencil

Hammer

#2 Phillips Screwdriver

5/16˝ (8 mm) nut driver (for concrete screws)

Hand Drill

9/32˝ (7.1 mm) drill bit (drywall screws)

5/32˝ (4 mm) drill bit (concrete screws)

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com

Fig. 1

Mounting Screws, Concrete screw on the left,

Drywall screw on the right.

4.650

[118.1]

MAXIMUM

INTERNAL

FOOTPRINT

6.890

[175]

MAXIMUM

INTERNAL

FOOTPRINT

9.450

[240]

6.650

[168.9]

3.000

[76.2]

2.890

[73.4]

MAXIMUM

INTERNAL

FOOTPRINT

2.000

[50.8]

MAXIMUM

INTERNAL

FOOTPRINT

MAXIMUM

INTERNAL

FOOTPRINT

2.930

[74.4]

4.840

[122.9]

MAXIMUM

INTERNAL

FOOTPRINT

2.125

[53.98]

4.750

[120.7]

6.750

[171.5]

H-2-TG:TEMPLATE 6/4/08 10:18 AM Page 1

MOUNTING

Note: The Series TG cover comes off the mounting

base (it does not rotate on hinge).

Step 1: Removing the Cover

A) Use the key to unlock the cover.

B) Open the cover approximately 15 degrees.

C) Slide the cover off the hinge.

Step 2: Mount the Base

A) Place the cover over the device to be protected and

mark the mounting holes using a pencil.

B) Cover the device to be protected with a damp towel

to prevent dust from getting into the device.

C) For drywall applications, drill four 9/32˝ (7.1 mm)

holes in the marked location from step 2A. For

concrete or cinder block applications, drill four

5/32˝ (4 mm) holes to a depth of 1-3/4˝ (45 mm) in

the marked location from step 2A. Skip step 2D for

concrete and cinder block applications.

D) Insert the plastic anchors until they are flush with the

wall surface.

E) Attach the base to the wall using the appropriate

screws provided.

Step 3: Re-Attach Cover

A) Slide cover hinge slots over the hinge tabs on the

base.

B) Close cover to base.

C) Use the key to lock the cover in place.

Note: Replacement keys may be purchased from the

factory using model number TG-KEY.

MAINTENANCE

Upon final installation of the Series TG Polycarbonate Wall

Mount Thermostat Covers, no routine maintenance is

required. The Series TG is not field serviceable and should

be returned if repair is needed (field repair should not be

attempted and may void warranty). Be sure to include a

brief description of the problem plus any relevant

application notes. Contact customer service to receive a

return goods authorization number before shipping.

Fig. 2

Mounting Diagram

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com

H-2-TG:TEMPLATE 6/4/08 10:18 AM Page 2

Dwyer Series TG User manual

Dwyer Series TG User manual

Dwyer Series TG User manual

Related papers